Search Documents

By B. Blumenthal

THE present investigation was planned as a survey of the lead-rich portion of the ternary lead-antimony-silver system by thermal analysis. Since, however, a rigorous application of the conventional thermal analytical method is time consuming, an attempt was made to speed up the investigation by reducing the time required for a single thermal analysis. This was done by increasing the rate of cooling to 12° to 18°C. per minute. Since such a rate does not permit even an approach to equilibrium conditions, the melt was stirred vigorously by a stirrer operating at the high rate of 665 r.p.m. This proved to be effective in obtaining cooling curves with distinct points of arrest and of excellent reproducibility, which satisfactorily compare with those obtained at a rate of 1° to 2°C. per min. with or without slow stirring (Fig. 1). By this method the lead-rich end of the lead-antimony system and a series of ternary alloys in sections parallel to the lead-antimony side of the ternary system were investigated and it was observed that the two branches of the' liquidus curve of the .binary alloys did not intersect at the eutectic temperature. An equivalent effect was observed in the ternary system. The eutectic temperature of the binary lead-antimony system was found to be 252.0°C., which confirms the recent investigation by Pellini and Rhines,1 who determined the eutectic temperature to be 251.5°C. The observation that the curves of primary crystallization of the lead-antimony system do not intersect at the eutectic temperature was previously made by Dean.2 Dean explains the phenomenon by assuming the existence of a compound Sb4Pb. He felt that super-cooling was not the cause of the phenomena because he was unable to influence them by inoculation. The X-ray investigation by Solomon and Morris-Jones,3. the metallographic investigations by Stead,4 Charpy,5 Gontermann,6 and Dean, Zickrick and Nix,7 and the numerous investigations of physical properties, definitely disprove the occurrence of any compound. The work of Dean was not confirmed by Broniewski and Sliwoski,8 whose experiments did not show any irregularity and who report a eutectic composition of 13 per cent antimony and a eutectic temperature of 250° to 252°C. at a rate of cooling of about 6°C. per min. Abel, Redlich and Adler9 then report a eutectic composition of 12.1 per cent upon reviewing the previous, publications and adding a few of their own cooling curves. In 1934 Quadrat and Jiriste10 found from careful analyses of the bottom portion of slowly cooled hypereutectic melts that the eutectic contains only 11,4 to 11.5 per cent antimony. (Previous analyses by Stead4 in 1881 gave 13 per cent:) Weaver," however, reported in 1935 that cooling curves indi-

Jan 1, 1943

By Benjamin S. Lindsey, James Norman

BARITE (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some kinds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to 100 per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaSO4, 11.11 per cent Si02, and 2.85 per cent R203. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder ,was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.' The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of nonmetallic minerals in the presence of a large amount of slime is usually very difficult, and when done is an innovation calling for conditions different from those under which granular material is separated. LABORATORY FLOTATION WORK Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coe1 for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1941

By Fred W. Stiefel

THIS paper covers the operation and maintenance of Diesel locomotives underground on a portion of the Delaware River Aqueduct.[t] This part of the tunnel is r5 miles long, with shafts 14 ft. in diameter spaced about 5 miles apart. These shafts (2, 2a and 3) are 825 ft., 1551 and 840 ft. deep, respectively. The grade of the tunnel is almost level, except for the 12,100 ft. north of shaft 2, which has a grade of 2.31 per cent. The tunnel is circular, 19 to 19 ft. in diameter, It lies at a depth of 400 ft. below sea level, with a maximum overburden of 2400 feet. The tunnel driving was carried on in six headings, using 15 storage-battery locomotive each of 13 gross tons and having a [inum] speed of 8 miles per hour. The longest haul was 3 miles, which proved to be the maximum distance for which storage-battery locomotives could be employed economically for the amount of material to be moved. One locomotive was used for switching cars at each heading, one for switching cars at the bottom of each shaft and one on the main-line haul from the heading to the shaft. The maximum amount of material hoisted in one shaft from two headings when 104 ft. of tunnel was driven in 24 hr. was 1000 cu. yd., or about 2000 tons of rock in place. The total quantity excavated was 950,000 cu. yd. (1,500,000 tons of rock). The tunnel-lining operations using con¬crete presented a problem of hauling a maximum distance of 5 miles in the tunnel. The concrete-placing equipment had a capacity of about 2000 cu. yd., or 4000 tons in 24 hours. Experience had shown that storage-battery equipment could not handle this quantity of material within the time required at the distance of 5 miles, Trolley-locomotive haulage was considered dangerous and expensive, and would cause interference because transmission equipment would be required. Therefore the performance of Diesel locomotives of 160 hp., with a speed of 18 miles per hour, in comparison with that of other types of locomotives, was studied. CHOICE OF LOCOMOTIVES In deciding upon the type of locomotive to be used for the 5-mile haul, four alternatives were considered, as follows: I. To purchase additional storage-battery locomotives with the necessary batteries over the 6 locomotives and 12 batteries available. 2. To convert the existing battery locomotives to the trolley type. 3. To purchase new trolley locomotives. 4. To purchase Diesel locomotives. PROPOSITION No. I The go-hp. storage-battery locomotives available (each weighing about 12 tons), when hauling a load of 64 tons, with a drawbar pull of about 1900 lb. on a level track, developed a speed of 8 miles per hour and could make five round trips in 8 hr. with a

Jan 1, 1942

By James Norman

BARITE (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some kinds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to loo per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaSO4, 11.11 per cent SiO2, and 2.85 per cent R2O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.' The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of nonmetallic minerals in the presence of a large amount of slime is usually very difficult and when done is an innovation calling for conditions different from those under which granular material is separated. LABORATORY FLOTATION WORK Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coe1 for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1941

By Kenneth M. Bravinder, Jonathan E. Koogle, Dean H. Sheldon

The solution of subsurface geological problems requires an analysis of vertical and horizontal dimensional relationships. For many, the ability to visualize structures in three dimensions is not easily acquired, and for areas where the structural conditions are complicated by faulting the need arises for illustrative models. This has led to the many forms of peg models, in which the usual course of construction includes a peg for the well bore, and the suspension of strings from peg to peg to illustrate the formation correlation between wells, thus developing the usual folds and flexures. Such models proved unsatisfactory for the analysis of fault problems. Consideration was then given to the use of transparent materials. A model of the Dominguez oil field was constructed in 1935, which consisted of a series of glass panels irom well to well on which the formations were shown in color. This model, though serving its purpose at the time, proved to be impractical from the standpoints of cost, breakage hazard, and extreme difficulty in maintenance. The cost of materials was estimated to be approxi-mately $300, and the construction required the services of one man for a period of from 10 to 12 months. Maintenance after actual construction was an additional expense. Consideration was then given to the use of celluloid, and aiter some experimental work it was found that the advantages in its use were: (I) a short construction time, (2) ease of handling the material, (3) sec-tions are easily reworked, (4) low cost. Construction It would be of little value to recount here the difficulties encountered in the building of the first celluloid model. The conclusions drawn, however, suggest the following pro-cedure for those who contemplate the construction of such a model: 1. Determilzatiolz of the Scale.—Accurate geological interpretation requires the use of the same scale horizontally and vertically. It should be emphasized that the limited size of the celluloid sheets (20 by 48 in. maximum dimensions), the area to be studied, the maximum depths to be plotted, and area of possible future development are the controlling factors in adopting a scale to he used. 2. Construction of the Base.—A satisfac-tory base may be constructed by using two pieces of three-ply wood separated by strips of I by 2-in. material. This type of construction prevents warping of the base. The size of the base is determined by the dimensions of the area to be studied plus 5 in. on all sides. A map of the same scale as that adopted for the model, indicating the lines of section to be used, should be fastened to the base. 3. Constructiolt of the Frame (Fig. I).—In the construction of the frame the use of %-in. 0.d. pipe welded in a box shape is suggested, with two horizontal rods on each of the four sides, top and bottom. The top rod should be at least r in. higher than the

Jan 1, 1941

By Ferit Gurses

EXTENSIVE coal and lignite deposits exist in Turkey. Bituminous coal is the nation's principal mineral resource; important not only as fuel for the industrial development of the country, but also as a means of obtaining foreign exchange. Of the electrical power generated during 1939, 82.8 per cent was derived from coal.1 It is anticipated that the lignite deposits will be one of the major sources of power for the electrification of the country. BITUMINOUS COAL The locations of the four principal bituminous-coal2 basins are indicated on Fig. 1. The Eregli-Zonguldak basin lies on the Black Sea northwest of Ankara; the Canakkale basin lies near the junction of the Dardannelles; the Trakya basin is in European Turkey northwest of the Bosphorus and the Erzurum basin lies far to the east. The Eregli-Zonguldak basin is the most important of the four. This coal basin was discovered in 1829 but did not arouse interest until 1848; up to 1865, its annual production had not exceeded 50,000 metric tons. In 1865, during the Sultanate, working of coal mines was started by the Navy department, and the annual production was 61,145 metric tons. In 1908, the Minister of Commerce and Agriculture was authorized to develop the whole coal basin. Production reached 264,397 metric tons in 1910, and during 1915-1922, preceding the revolution, the total production of the basin was 2,676,043, or an average of 334,000 metric tons annually. The period of national revolution that followed was marked by a steady increase in coal production in Turkey, although world production decreased, because of the crisis of 1929-1932, about 52 per cent. AREA AND GEOLOGY OF THE COAL BASIN The geology of the Eregli-Zonguldak area is not yet completely known. The basin begins at Gungazi, to the west of Eregli, and extends to Sogutozu, a distance of about 106 miles. The coal beds, however, appear only in places and the overlying Cretaceous strata hide them elsewhere. This area includes the most important centers, such as Kandilli, Alacaagzi, Teflenli, Kozlu, Gelik (see Fig. 2). The geological sequence of the district is correlated with the Cretaceous of the Balkans; which is, in turn, a prolongation of the Alpine zone. Geological surveys made by G. Ralli, R. Zeiller and P. Arni3 show that the Eregli-Zonguldak formations fall into three natural divisions. Series a, The Alacaagzi in the district of that name (Fig. 2), is of the Culm stage. The strata strike generally east-west and dip about 30° south. This series appears also around Kandilli and Camli, with a steeper angle of dip, but the deposits there lack regularity. The Alacaagzi stage appears also farther east, to the south of Kozlu and Gelik. The Alacaagzi series contains 15 seams of an average thickness of 2 ½ ft. of good coal. Series b, the Kozlu, best represented in Zonguldak, Kilimli, Catalagzi, and between

Jan 1, 1944

By Kenneth M. Bravinder, Jonathan E. Koogle, Dean H. Sheldon

The solution of subsurface geological problems requires an analysis of vertical and horizontal dimensional relationships. For many, the ability to visualize structures in three dimensions is not easily acquired, and for areas where the structural conditions are complicated by faulting the need arises for illustrative models. This has led to the many forms of peg models, in which the usual course of construction includes a peg for the well bore, and the suspension of strings from peg to peg to illustrate the formation correlation between wells, thus developing the usual folds and flexures. Such models proved unsatisfactory for the analysis of fault problems. Consideration was then given to the use of transparent materials. A model of the Dominguez oil field was constructed in 1935, which consisted of a series of glass panels irom well to well on which the formations were shown in color. This model, though serving its purpose at the time, proved to be impractical from the standpoints of cost, breakage hazard, and extreme difficulty in maintenance. The cost of materials was estimated to be approxi-mately $300, and the construction required the services of one man for a period of from 10 to 12 months. Maintenance after actual construction was an additional expense. Consideration was then given to the use of celluloid, and aiter some experimental work it was found that the advantages in its use were: (I) a short construction time, (2) ease of handling the material, (3) sec-tions are easily reworked, (4) low cost. Construction It would be of little value to recount here the difficulties encountered in the building of the first celluloid model. The conclusions drawn, however, suggest the following pro-cedure for those who contemplate the construction of such a model: 1. Determilzatiolz of the Scale.—Accurate geological interpretation requires the use of the same scale horizontally and vertically. It should be emphasized that the limited size of the celluloid sheets (20 by 48 in. maximum dimensions), the area to be studied, the maximum depths to be plotted, and area of possible future development are the controlling factors in adopting a scale to he used. 2. Construction of the Base.—A satisfac-tory base may be constructed by using two pieces of three-ply wood separated by strips of I by 2-in. material. This type of construction prevents warping of the base. The size of the base is determined by the dimensions of the area to be studied plus 5 in. on all sides. A map of the same scale as that adopted for the model, indicating the lines of section to be used, should be fastened to the base. 3. Constructiolt of the Frame (Fig. I).—In the construction of the frame the use of %-in. 0.d. pipe welded in a box shape is suggested, with two horizontal rods on each of the four sides, top and bottom. The top rod should be at least r in. higher than the

Jan 1, 1941

By A. Raman

The Nb-Co system was nuestigated in the range 10 to SO at. pct Co with X-rays. A pt phase with the W6Fe.r-type structure occurs in the system between 46 and 52 at, pct Co. Its unit-cell dimensions are nearly identical to those of the p Phases found in the Nb-Fe and Nb-Ni systems. Two Laves phases, one having the MgZnz-type structure and the other the MgCuz-type structure, already t-eported in the literature, are found to exist in the system. The ,l.IgZnz-type phase occurs between 62 and 64 at. pct Co. A MgNi2-type Laves phase, reported in the literature, is no! obtained. A binalry phase is found to exist belozv I000C around 82 at. pct Co. THE cobalt-rich side of the system Nb-Co has been repeatedly investigated by previous inestiators" and the following intermediate phases are known to occur: NbCo, which crystallizes in the MgCu2-type structure and Nbc03,' reported originally by Wall-bam, which has the MgNiz-type structre. Jordan and uwez' as well as lliott' were unable to find the MgNiz-type phase. Two phases, designated as x and y, were reported by Saito and eck.' The phase x was inferred to have a narrow composition range near 77 at. pct Co. No published work is known to the author which reports the investigations in the niobium-rich portions of the system. This paper presents the results of an investigation in the Nb-Co system between 10 and 80 at. pct Co. EXPERIMENTAL PROCEDURE Two or three grams of the alloys under investigation were prepared using niobium (99.9 pct +) and cobalt (98.8 pct + with 0.14 pct Fe and and 0.03 pct C) in a tungsten-electrode arc furnace under commercial argon atmosphere. They were then wrapped in molybdenum sheets and annealed for a period between 5 days and 1 week at 1300°C in high vacuum (10-" orr) or in evacuated quartz amules for 2 weeks at 1000°C. Powders of -325 mesh size were prepared for X-ray work by crushing and grinding the specimens. Subsequent reannealing of the powders was not undertaken since most of the alloys were brittle and broke easily. X-ray powder patterns of the as-cast and annealed samples were prepared in a Siemens cylindrical camera (57.3 mm radius) with Cr-K, radiation. A Siemens diffrac to meter was used to get the X-ray patterns of some new phases. Metal log raphic examination of the alloys supplemented the X-ray findings. RESULTS The results of the X-ray and microstructural analysis Of the alloys are in in Table I. The lattice parameters of the phases are listed in Table 11 for quick reference. A set of micro photographs in Fig. l(n) to (j) show the microstructures of some alloys. A probable equilibrium diagram is drawn in Fig. 2

Jan 1, 1967

By S. C. Sircar, B. K. Dhindaw

KINETICS and mechanism of sulfation reactions have been studied extensively. Qualitative and quantitative data are reported for the kinetics and mechanism of sulfation reaction of copper oxide pellets;''2 yet it remains a controversial Subject. The mechanism and kinetics of the sulfation of zinc oxide powder (B.D.H. analar quality) were studied by gravimetric technique. A spring of high-carbon steel wire with accuracy well within 0.2 mg was used for measuring weight change. The sample was taken in a Pyrex glass bucket, hanging freely inside a Pyrex glass tube reactor, with a gold wire attached to the spring, the reactor being surrounded by a movable furnace (double wound type) with a temperature control within *5"C. Flow of oxygen, 60 cu cm per min, and sulfur dioxide, 45 cu cm per min, were measured through calibrated flowmeters and the mixture dried over PZ05 before entering the reactor. The experimental results are presented in Figs. 1 and 2. The plot of weight change of zinc oxide, giving the amount of zinc sulfate formed, was found to be linear over the temperature range of 500" to 700° C and up to a conversion of approximately 60 pct, as beyond it they divert from linearity.' The rate of sulfation was found to be affected by total flow rate of gases at a fixed ratio of SO2/O2, up to 60 cu cm per min, and was found to be linearly dependent on quantity of total powdered sample taken. The plot of rate of sulfation of zinc oxide, 70 mg, with varying amounts of vanadium pentoxide, at a constant ratio of gases as mentioned above, and at a constant temperature of 625"C, was also found to be linear as seen in Fig. 2. Extrapolation to zero V2O5 addition gives the same rate of sulfation, as in case of pure zinc oxide, 70 mg. Vz05 was prepared by heating ammonium vanadate at 600°C for 15 min in a muffle furnace. The available literature points out that the theory of sulfation that has received the maximum support postulates the following mechanism for sulfation of ZnS: 2ZnS + 30, = 2Zn0 + 2SOZ; the ZnO formed acts as a catalyst for the reaction, 2 S02 + O2 = 2S03. This SO3 reacts with ZnO to give zinc sulfate. It is suggested here that the above widely supported mechanism is operative in the sulfation reaction and that the rate-controlling step in the sulfation reaction of ZnO is the formation of SO3 from SO, and 0,. The authors are carrying on further work in this line, and the details will be published later. The authors wish to acknowledge the facilities provided and the help extended by Prof. P. R. Dhar, Head, Department of Metallurgical Engineering, and the permission granted to publish this note by the Director, I. I. T., Kharagpur.

Jan 1, 1969

By James Norman, Benjamin S. Lindsey

BaritE (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the 'more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some kinds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to 100 per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaSO4, II.II per cent SiO², and 2.85 per cent R²O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.' The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of non-metallic minerals in the presence of a large amount of slime is usually very difficult, and when done is an innovation calling for conditions different from those under which granular material is scparated. Laboratory Flotation Work Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coe1 for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1942

By Benjamin S. Lindsey, James Norman

BARITE (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some kinds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to 100 per cent through 325mesh. The crude rock with which all test work was done assayed 85.1 per cent BaSO4, 11.11 per cent Si02, and 2.85 per cent R2O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.1 The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of nonmetallic minerals in the presence of a large amount of slime is usually very difficult, and when done is an innovation calling for conditions different from those under which granular material is separated. LABORATORY FLOTATION WORK Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coe1 for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1941

By Benjamin S. Lindsey, James Norman

BaritE (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the 'more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some kinds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to 100 per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaSO4, II.II per cent SiO², and 2.85 per cent R²O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.' The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of non-metallic minerals in the presence of a large amount of slime is usually very difficult, and when done is an innovation calling for conditions different from those under which granular material is scparated. Laboratory Flotation Work Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coe1 for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1942

By J. Philip Neal, Carroll P. Rogers

Feldspars, the most abundant minerals of the igneous rocks, occur in numerous forms and mixtures. The feldspars of commercial significance are found in widely distributed pegmatites as large crystals usually free of iron- bearing impurities and thus suitable for hand-cobbing, and also in larger bodies where the ore contains various types of feldspar inter- mingled with quartz and relatively free of iron- bearing impurities, or at least readily unlocked from impurities present at relatively coarse mesh. The latter type of ore includes some pegmatites, and the ''alaskite" bodies so common in the Spruce Pine district of North Carolina. On the west coast of the U.S. and in Oklahoma there is-r has been--commercial recovery of natural feldspathic sand as a source of alumina in glass and ceramics. "Aplite" in commercial terminology is a light-colored igneous rock with a granitic composition and a fine sugary texture, often banded with readily removable iron impurities. Two areas in Virginia produce aplite for the glass industry: one located in the vicinity of Piney River, Amherst County, and the other near Montpelier in Hanover County. According to Deer et al. (1966) the word feldspar derives from the Swedish feldt or falt (field) and "spath:" chunks of rock appearing in tilled ground overlying granite. Castle and Gillson (1960) indicate a Germanic origin, citing "spat," which is said to refer to any transparent or translucent material which is readily cleavable. The term "spar" has in the past been applied to minerals other than feld- spar, such as barite, calcite, and fluorite. It is correct to call the latter "fluorspar." There is a true barium feldspar, but it is rare and of no present economic importance. What is recognized as feldspar or "spar" by present producers and consumers consists of three silicate minerals which, if pure, would have the formu- las KAISi,O, (microcline or orthoclase), NaAlSi,O, (albite), and CaAl,Si,O, (anorthite). These are almost never found in pure form in nature, but occur together in great abundance in a three-component system. A considerable number of different combined ratios of these three exists, with the exception that isomorphism between potassium spar and calcium spar is very limited. User specifications for feldspar products are largely built around the prevalent naturally occurring ratios. Pas- sages following will refer to "K-spar," "Na- spar," or "Ca-spar." Nomenclature and Descriptive Terms Relating to both the mineralogy and the economics of feldspar are certain terms whose coverage it is useful to specify. Commercially, aplite is a feldspathic rock mined and beneficiated in two locations in Virginia, in which both titanium and feldspar minerals are present-the latter now being the major, if not the only, economic product. Technically, the term aplite when applied to this rock is of questionable accuracy. But, in light of accepted commercial usage, the term will be here used to designate it. Regarding the Virginia rock, Ross (1941) is cited.

Jan 1, 1975

By Walter S. Weeks

In this paper the effect of natural ventilation pressures is considered a part of the mine resistance and it is shown that their effect on the mine resistance is not the same as the total natural ventilation pressure of the shafts if the mine has several levels. It is shown that increasing the fan pressure causes the division of the air to approach the condition that would obtain if there were no natural ventilation pressure present. It is shown that if an appreciable difference in pressure is maintained between the beginning and end of a group of splits, the value of the integrated effect of the natural ventilation pressures on the individual splits does not change substantially with moderate changes of this pressure. A method is outlined for determining the resistance factor of the mine and the value of the effect of natural ventilation with the fan operating; also a method for determining this factor when circulation is caused by natural ventilation alone. Natural Ventilation Pressure Natural ventilation pressure (N.V.P.) is caused by the difference in weight of the air in two similar columns between two horizontal planes, and the difference in weight is caused principally by the difference in temperature of the two columns. The fan pressure causes some variation in density, but, since it is usually small and affects both columns, its effect is relatively unimportant. It has been suggested that "N.V.P." be called "stack effect"; but, since the term N.V.P. was used in a previous Institute paper,' applied in exactly the same manner, the term will be used. Frictional Resistance The frictional resistance to flow in a mine without natural ventilation may be expressed as RQ2 where R is a constant for a given air density and Q is the rate of flow. This frictional resistance plus the effect of velocity changes will be called the F pressure (F.P.) and a curve of F.P. against Q, the F characteristic of the mine. If a pressure is applied to a mine by a fan, the air flow so adjusts itself that the drop in pressure through any path from entrance to exit of mine, due to frictional resistances and velocity changes, is the same as that in any other path. The mine resistance varies as the square of the quantity. The air distribution without N.V.P. will be called "normal." Natural Ventilation Present When N.V.P. is irregularly distributed in a mine, it is more convenient in analysis to consider the N.V.P. as a part of the duct resistance. If it is so considered the resistance no longer varies as the square of the quantity, and if N.V.P. exists between levels the distribution of the air is no longer normal. The total N.V.P. of the mine is the pressure caused by the full length of the shafts. If a mine has several levels, N.V.P. exists

Jan 1, 1946

By G. H. Anderson

Cadmium-coppeR precipitate, a byproduct of the purification stage of the zinc plant, is composed mainly of zinc, cadmium and copper in varying amounts depending on the efficiency of precipitation and the cadmium and copper contents of the impure solution treated. The composition range is approximately: cadmium 10-12 pct, copper 6-8 pct, and zinc 3&35 pct. As received at the cadmium plant, the precipitate is a dark gray to black press cake produced by filter pressing the flocculent cadmium-copper precipitate formed when impure zinc solution is agitated with zinc dust. The details of the cadmium-copper precipitation are to be found in the paper "Electrolytic Zinc at Risdon, Tasmania," by W. C. Snow. Transactions AIME, 121, 501. The treatment, in addition to recovering cadmium as metal, yields a copper product as a residue for realization and recovers in solution for return to the zinc plant, the excess of zinc dust used during purification. The recovery of cadmium metal is approximately 200 tons† per year, but, with the amount of copper residue recovered, varies with the zinc production tonnage, composition of the original concentrates, degree of roasting and other operational factors. The operations involved in the recovery of the foregoing materials are carried out in a building adjacent to the purification section of the zinc plant and can best be described by dividing the process into the following stages: 1. Oxidation and Grinding of the cadmium-copper precipitate. 2. Leaching and Filtering. 3. Precipitation of cadmium. 4. Oxidation and Grinding of the precipitated cadmium. 5. Leaching oxidized cadmium precipitate and Purification of leach solution. 6. Electrolysis. 7. Melting, Casting and Packing. A feature of the process is the use of two distinct solution circuits. Spent electrolyte from the zinc plant circuit containing about 10 pct sulphuric acid is used as the primary solvent of the cadmium and zinc present in the oxidized precipitate. When the cadmium is later separated by precipitation and filtering, the filtrate, originally zinc plant spent electrolyte and now fortified in zinc, is returned to the zinc plant. The precipitated cadmium, after oxidation, is redissolved in spent electrolyte from cadmium electrolysis which solution is in closed circuit within the cadmium plant except for discards to the zinc plant circuit as mentioned in Section 5 hereinafter. (Fig 1.) Details of the various operations follow. I. Oxidation and Grinding of the Cadminm-copper Precipitate The precipitate having had a preliminary drying by compressed air in Dehne filter presses in the zinc plant is trucked to a storage platform of sufiicient length to store 3 to 4 days' production separately. After 48 hr exposure to atmosphere, oxidation is sufficient to enable all cadmium and zinc but only a portion of the copper to be dissolved in dilute sulphuric acid. The oxidized precipitate is shovelled into trucks and, after weighing and sampling, is broken in size by means of

Jan 1, 1950

By W. M. McCardell, W. O. Winsauer, M. Williams

The mechanism by which an electrical potential difference is developed between two salt solutions separated by shale is shown to be a consequence of the electrical double layer of the shale surfaces. A mathematical derivation is presented to show -the dependence of the potential on the shale characteristic.? and on the concentration of the salt solutions. The equations developed describe adequately the potential-concentration behavior of a long shale core. The equations also describe the variation of potential of sand-shale mixtures with variation of clay content. Ion adsorption i* an important factor in he developments of the surface charge on the shale. and electrical resistivity and ion transference number data are emlployed to estimate the increase of surface charge with concentration. Since the potential is shown to be dependent on the characteristics of the particular .system. water salinities estimated from the potential log by previously proposed methods may be low in some rase;. INTRODUCTION That the electric well log exists today may he attributed to the ingenuity of the Schlumberger brothers who adapted to the logging of wells techniques which were originally developed as surface prospecting methods for the location of ore bodies Empirically it was found that the potential curve of the electric log usually gave values for clean sands which were negative with respect to the values for shales. It was suggested that the potential was responsive to porosity. It was postulated in explanation? that the potential was the sum of a streaming potential, which differed for sands and shales, and of an "electro-chemical" potential of undetermined origin. Mounce and Rust in 1943 showed that the streaming potential is small in most cases and that the potential is generated by a process in which shale and a salinity difference play-essential party. Dickey.:' in the same year, concluded that the potential is dependent upon adsorptive properties of reservoir rock. Wyllie in 1949. and Wyllie and Patnode, in 1950, measured the potential-: between two salt solutions separated by barriers of either naturally-compacted or artificially-compacted shales and concluded that the potential can be expressed by where E is the potential R is the gas content F is Faraday's constant T is the absolute temperature are the activities of the two uni-univalent solutions These authors postulated that shale. in the ideal case is impermeable to the migration of negative ions. Any potential less than the "ideal" shale potential was considered to be due to imperfections in the shale barrier. Although the studies by Wyllie and Patnode of the development of the shale potential are fairly recent. investigators in fields other than well logging have discussed the mechanisms responsible for analogous potentials over a period of several decades. Although it is evident that much thought has been devoted to the question of the origin of the potential observed in wells, it is also apparent that all of the explanations presented to

Jan 1, 1953

By E. I. Radzinovsky, D. W. Dareing

This paper presents theory which is used to predict rock-bit bearing life reduction due to simple harmonic variations in bit forces. The theory is based on the premise that if a constant load acts for a certain fraction of the life which the bearing would have if that constant load were applied for its entire life, then the same fraction of thelife of the bearing is consumed. Total bearing life is related to simple harmonic variations in bearing life associated with instantaneous bearing loads. The results show that rock bit bearing life is not affected appreciably by forces commonly impressed upon a bit, but it is affecied appreciably by relatively large dynamic bit forces occasionally encountered during drilling. In addition, the results show that the life of sealed bearings is more sensitive to bit force variations than is the life of unsealed bearings. INTRODUCTION Roller bearings are important components in roller cone rock bits because they transmit a large portion of the drill collar weight to the formation being drilled. Unfortunately, they have a relatively short life under down-hole drilling conditions. Roller bearings are usually the first bit components to fail, and their failure leads immediately to failure of the entire bit. Short roller bearing life, and thus short bit life, is due mainly to high unit loads transmitted by the bit and to the adverse environment in which the bearings operate. The results of the study discussed in this report show how dynamic bit forces also affect roller bearing life. The purpose of this paper is to discuss theory developed to predict the effect of different magnitudes of periodic bit forces on roller bearing life. Theoretical results are used to compare the life of rock bit roller bearings subjected to steady forces to the life of rock bit roller bearings subjected to unsteady forces similar to the type of unsteady forces measured at the bit with a special downhole recording instrument. BACKGROUND AIanufacturers of bearings have conducted laboratory tests which show how bearing life is affected by steady bearing load. 1 The well-known empirical equation which defines bearing life follows from bearing test data. It is: where L = bearing life, hr P = bearing load, Ib C = constant q = exponent (constant). The effect of environment on bearing performance is manifested through the exponent q and the constant, C. King,2 in similar tests conducted on roller bearings used in rock bits, showed that, in addition to the load, the environment (abrasive materials, chemical components, etc.) greatly affects bearing life. His data, which show how the life of roller bearings in a 7-7/8-in. W7R bit rotating at 60 rpm is affected by bit weight and fluid environment, are displayed on a log-log plot by broken lines made up of straight line segments. Each broken line corresponds to a given environment. One segment (q = 1.4) of the broken line corresponding to a fluid environment of barite mud is shown in Fig. 1 along

Jan 1, 1966

By T. E. Tietz, J. E. Dorn

Activation energies for creep of copper at intermediate temperatures, where crystal recovery was negligible, were determined by the simple technique of rapidly alternating the test temperature between and T2 (T2 = TI + about 10°K) throughout a constant stress creep test. The activation energy for creep H was found to be 37,000± 3,000 cal per mol, independent of stress and strain. The same creep laws as have been previously established for high temperature creep were found to be valid for creep at intermediate temperatures. But the AH was found to be lower than that for self-diffusion in the intermediate temperature range whereas it is known to be equal to that for self-diffusion at high temperatures. IT is now well established that creep at high temperatures can be correlated by the functional relationship'-" e = f(?) s = constant [I] where E is the total plastic strain, f is the function that depends on the stress, ? = f e -- dt, t is the duration of test, e is the base of natural logarithms, AH is the activation energy for creep, R is the gas constant,T is the absolute temperature, and s is the stress. Thus, identical values of are achieved during creep under a given stress at two alternate temperatures at the same total strain. At the same strain therefore where subscripts refer to the two alternate temperature conditions of test. Consequently, the activation energy for high temperature creep is readily obtained with the aid of Eq. 2. Activation energies so obtained have been observed to be insensitive to the creep strain at which they are evaluated, the applied stress, grain size, minor alloying additions,'-' cold worked state, and the presence of thermally stable dispersions of intermetallic compounds in an a solid solution matrix Furthermore, the activation energy for high temperature creep is very nearly equal to that for self-diffusion in all cases where adequate data are available for comparison." " The apparent identity of the activation energies for high temperature creep and self-diffusion strongly suggest that high temperature creep arises from a dislocation climb process. This hypothesis is further strengthened by the fact that the energy of activation for high temperature creep is insensitive to the applied stress," and by the observations that the correlation suggested by Eq. 1 cannot be ex- tended to temperatures below those for rapid crystal recovery. When using the activation energy for self-diffusion, Eq. 1 fails to give the required correlations between creep curves at various intermediate temperatures.' This suggests that the dislocation climb mechanism for creep might be superseded by some alternate mechanism in the intermediate range of temperatures. This investigation was initiated in a preliminary attempt to ascertain the type of creep law that might be valid in the intermediate range of temperatures. Special consideration, however, was given to the determination of the activation energy for creep in this range because the Becker-Orowan', " and the Mott-Nabarro10 theories for transient creep suggest that the activation energy should increase

Jan 1, 1957

ROBERT PEELE, * New York, N. Y.-I should like to ask Mr. Neale how the members of the production committees at the individual mines, who came from the mine workers themselves, were chosen or appointed; also from what classes of employees they usually came? J. B. NEALE.-In the union fields, they were chosen by a local. In the non-union fields, they were chosen either by the men in mass meeting or by the company officials. The last way was very unsatisfactory because it gave the men an opportunity to say that they were going to be passed upon as to whether they were slackers or not, by men chosen by the company. When they were chosen by the locals or at mass meetings of the workers, the appointments have been very much more satisfactory. R. D. HALL, ? New York, N. Y.-The matter of inefficiency on the part of the operator is one that I think we may well take into account, because there is a very large inefficiency on the part of the coal operator; it has arisen from reasons almost beyond his control and will continue for these same reasons. It is no use arguing a moral responsibility on the part of the operator, when you make efficiency very largely a loss to the operator who puts it in force. If you ask a man working on a clay wage to work with more efficiency. he says, "Well, I may do it or I may not," it all depends how he feels, but he does not lose anything financially by not working hard. If you ask the man who is working by the ton to put out more tons, he makes a profit by putting out more tons. How is it with the operator? If he gives a man all the cars he needs and all the power he needs, if he runs after his working men and waits on them, he does not get his coal out any cheaper than before.. He gives the man a better chance and there is more efficiency, but at the same time he has increased his expenses all along the line. At the end of the year he finds that his profits have been less than if he had had less efficiency. The efficiency is really against him in many ways. Because he gets a larger tonnage, he reduces the overhead to a certain extent; but hiss tonnage may not be any greater because he may work fewer days. As Mr. Taylor remarked some tine ago, supposing he puts in a machine that is very much more effective than any he had before, he has the same scale; the miner gets out more coal, but he himself does not get any benefit out of it because he has a scale fixed, so much per ton.

Jan 4, 1919

R. H. Sweetser.—Mr. Reinartz spoke of slag containing 18 per cent FeO. I think he expressed the iron as oxide. I should like to ask at what point, in iron contents, it is usual practice to quit sending that open-hearth slag to the blast furnace? L. F. Reinartz.—NO problem is involved in disposing of open-hearth slag to our blast furnaces because, on account of the grades of iron and steel made by our company, the iron oxide in the slag is sufficiently high to make it very acceptable to the blast-furnace operator. I have been told that if the total iron oxide in the slag is under 18 to 20 per cent, it is not economical to use such slag in a blast furnace. J. T. Mackenzie,* Birmingham, A1a.—Mr. Reinartz mentioned sulfate in the limestone. I wonder if he did not use the wrong word. We always have assumed that the sulfate sulfur is practically harmless. Most limestone carries some pyrite (sulfide sulfur) which we thought was what gave the sulfur pick-up. L. F. Reinartz.—I have had no experience, personally, in the use of limestone high in sulfates. I have been told, on several occasions, by other open-hearth men, that the sulfates will be reduced and increase the sulfur content of the metal. We have never found any pyrite in our limestone. A. Hayes,† Middletown, Ohio.—I should think that sulfates would be readily reducible to sulfites, and possibly to sulfides at various distances through the slag layer, from the top down to the interface between the bath and the slag, because reducing conditions are certainly sufficiently strong next to the bath in the slag to reduce sulfates to sulfides. A. L. Feild,‡ Baltimore, Md.—What is Mr. Reinartz's theory as to the effect of silica in the slag on the iron oxide content of the metal? L. F. Reinartz.—I have no particular theory as to the effect of silica in the slag on the iron oxide content of the metal. I know from practical experience that it does have an influence on reduction of iron oxide in the metal. We know that if the silicon content of the charge, and, therefore, the silica of the slag is increased, the iron oxide in the slag will be decreased. Based on Dr. Herty's work, we assume that the iron oxide is correspondingly decreased in the metal. C. H. Herty, JR.,§ Bethlehem, Pa.—In the theory of iron oxide control, we have tackled the matter from the physical standpoint, rather than the chemical standpoint or from the slag itself, and we worked on the basis that the change in iron oxide content in a slag—that is, whether the slag increases or decreases in iron oxide—is due to the simple fact that if you put more iron oxide into the slag from the gas than you put oxygen from the slag into the metal, the slag must increase in iron oxide;

Jan 1, 1935