Search Documents

By P. F. Gnirk, J. B. Cheatham

Single bit-tooth penetration experiments under static load were conducted on six rocks at confining pressures of O to 5,000 psi using sharp wedge-shaped teeth with included angles ranging from 30 to 120° In general, the force-displacement curves for all rocks exhibit an increasingly nonlinear and discontinuous behavior with decreasing confining pressure. The confining pressure at which a rock exhibits a macroscopic transition from predominantly ductile to predominantly brittle behavior during penetration vmies from about 500 to 1,000 psi for the limestones to greater than 5,000 psi for dolomite. The correlation between calculated values of force per unit penetration based on plasticity theory and experimental values is quite encouraging, even at confining pressures as low as 1,000 psi A qualitative correlation between volume of fragmented rock per unit energy input for a single bit-tooth and drilling rate for microbits appears to exist over a confining pressure range of 0 to 5,000 psi. INTRODUCTION Laboratory experiments utilizing a small-scale drilling apparatus have demonstrated that penetration rates are reduced considerably as a result of increasing the confining pressure from atmospheric to a few thousand psi?-3 This undesirable situation can, in general, be attributed to a combination of decreased efficiency of chip removal at the bottom of the borehole, increased rock-failure strength, and a possible change in the mechanism of chip generation and rock fragmentation with increasing confining pressure. To more fully understand the principles underlying the last circumstance, it is the purpose of this investigation to experimentally study the mechanism of single bit-tooth penetration into dry rock at low confining pressures and, in particular, to establish the confining pressure at which the penetration mechanism may undergo a brittle to ductile transition for various rock types commonly encountered in drilling. Confining pressure as used here refers to the differential pressure between the borehole fluid pressure and the formation-pore fluid pressure. EXPERIMENTAL PROCEDURE Using an experimental apparatus previously described: a single, sharp wedge-shaped tool was forced under a "statically" applied load into an effectively semi-in finite dry rock sample subjected to a prescribed confining pressure. To prevent the invasion of the con fining-pressure fluid into the pores of the rock sample during penetration, the exposed surface of the rock was jacketed with a layer of silicon putty.* Electrical instrumentation incorporated into the apparatus yielded a graphical plot of force on the tool as a function of penetration or displacement of the tool into the rock during an experiment. During the course of the experimentation the following conditions were maintained constant: (1) pore pressure — atmospheric (i.e., the rock was dry); (2) temperature — 75F; (3) rate of loading — essentially static (approximately 0.002 in./sec); (4) bit tooth — a sharp wedge-shaped tool loaded normal to the rock surface; (5) rock surface — smooth and flat; (6) drilling fluid — hydraulic oil; and (7) maximum depth of penetration — approximateiy 0.1 in. In addition, each experiment was performed on a different rock sample so the rock surface is free of a layer of cuttings and of any previous indentation craters. The influence of the corners of a borehole was neglected, since each rock sample was cemented inta a section of aLuminum tubing to simulate a semi-infinite body. Indentation experiments were made on a sandstone, two limestones, a marble, a dolomite and a schist with a 60' bit-tooth over a range of confining pressures from atmospheric to 5,000 psi and at a constant confining pressure of 1,000 psi for a variety of bit-teeth with angles ranging from 30 to

Jan 1, 1966

By W. D. Forgeng, R. L. Folkman, D. C. Hilty

The solubility of oxygen in molten Fe-Cr alloys has been determined at 1550° , 1600°, and 1650°C for alloys containing up to alloyshasbeenabout 50 pct Cr and found to decrease as chromium increases to 6 pet and then to increase gradually. Phase relations in the Fe-Cr-0 system at steelmaking temperatures have been evaluated and two previously unreported oxides have been identified. OPERATIONS in the melting and refining of chromium steels are dependent to a major degree on the reactions of chromium and iron with oxygen and are primarily directed toward controlling and modifying these reactions to secure maximum advantage in the utilization of chromium. Although fairly effective practices have been developed empirically, understanding of the specific reactions is limited. Moreover, the ability of molten steel to dissolve oxygen that subsequently precipitates as oxide inclusions during solidification is well known, so that clarification of the effect of chromium on the nature and mechanism of formation of these inclusions is desirable. Study of the problem indicated that increased knowledge of the fundamental Fe-Cr-0 system is essential to further technical and economic improvement. Consequently, an investigation of the influence of chromium on the solubility of oxygen in molten iron and of phases and phase relations in the Fe-Cr-0 system was undertaken at the Metals Research Laboratories of the Electro Metallurgical Co. as part of a general program on the effective utilization of chromium in chromium steel production. Experimental Procedure All of the experimental runs made during this investigation were carried out in the rotating crucible induction furnace which has been described in detail in a previous publication.' In review, the principle underlying this furnace is that rotational forces in the crucible cause the molten metal to assume a concave shape in such a manner that the slag is contained in the molten metal cup, thereby minimizing slag/crucible contact and subsequent reaction. Practically all of the heats were melted in commercial-quality magnesia crucibles of the type usually furnished for laboratory induction furnaces. All of the runs were made under an argon atmosphere after the furnace chamber had been degassed. Bath temperatures were controlled by Pt—Pt-10 pct Rh thermocouples. The basic furnace charge consisted of a premelted 12 to 15 lb electrolytic iron slug which had been cast to a shape convenient for fitting into the rotating furnace crucible. A typical analysis of the electrolytic iron slugs is given in Table I. For certain runs, it was desirable to melt down charges containing high initial chromium contents. In these cases the chromium was added to the electrolytic iron during the premelting operations. Chromium was added to the rotating furnace bath in the form of electrolytic chromium of the analysis given in Table 11. In all of the constant temperature runs, the standard procedure was to melt down the electrolytic iron or alloy slug under vacuum, admit argon to slightly greater than atmospheric pressure, and adjust rotational speed to develop a well formed "cup" on the bath surface. The melt was then saturated with oxygen by an addition of ferric oxide and the temperature of the bath adjusted to within +5°C of the desired level. At this point the heat was permitted to come to equilibrium prior to sampling or further addition. This time interval was varied from 15 min to 2 hr but generally was about 20 min. After sampling, the desired chromium addition was made and the bath again equilibrated prior to subsequent sampling. This cycle of addition and sampling continued for the duration of the run which lasted from 4 to 8 hr. At the end of this period, power was shut off and the bath allowed to solidify in the furnace. Quenched metal samples were taken from the equilibrated melts by means of the "Taylor sampler" which has been described by Taylor and Chipman.' Before being submitted to chemical analysis, all samples were carefully examined for surface slag occlusions and cold shuts. Later in the study, each sample was radiographed and examined metal-lographically in cross-section to determine the presence of internal defects. On the basis of these examinations, sound and apparently clean specimens were selected from the Taylor samples for chemical analysis.

Jan 1, 1956

By L. A. Geoffrion, R. H. Perkins, J. C. Biery

Densities of cerium metal and several lour-melting binary cerium alloys were measured over the range 25° to 800°C. A rolumeter, using NaK as working fluid, was used to obtain the data. The cerium, Ce-Co, Ce-Ni, and Ce-Cu alloys all exhibited an increase in density on melting, while a Ce-Mn alloy expanded on melting. FOR the proper design of a nuclear reactor, the change in density of the fuel with temperature must be known. This is especially important in a system utilizing molten fuel, such as LAMPRE (Los Alamos Molten Plutonium Reactor Experiment), since a relatively large change in density usually occurs during the solid-liquid transition. The fuel for LAMPRE is a Pu-2.5 wt pct Fe alloy with a melting temperature of 410°C. However, limitations in reactor design with this fuel have led to consideration of other plutonium-containing alloys for use in future generations of this type of reactor. Several ternary alloys containing plutonium and cerium as two components have satisfactorily low melting points. The system that at the present time appears to be most acceptable is Pu-Ce-Co; it exhibits little change in melting temperature with wide variation in plutonium concentration. Other alloys that have received some consideration contain nickel, copper, and manganese as the third constituent. The proposed fuel alloys are difficult to handle experimentally in the 25" to 800°C temperature range since they oxidize readily, react with many solvents, and contain a poisonous fissionable material. In addition, in this temperature range the alloys pass through the solid-liquid transition. Several techniques are available for measuring the densities and volume coefficients of expansion of solids or liquids. However, the only apparatus that appears suitable for measuring expansion coefficients over this temperature range and through the phase transition is a volumeter. In a volumeter, the indicating medium must be essentially inert to and insoluble in the material being studied. It must also possess a low vapor pressure over the operating temperature range, and its coefficient of expansion must be accurately known. One material that is satisfactory in nearly all of these respects is the alloy Na-78 wt pct K, which melts at -10°C and has a vapor pressure of 860 mm Hg at 800°C. This relatively high vapor pressure at 800°C requires an overpressure of an inert gas to prevent boiling. While a volumeter is capable of determining accurately the volume coefficients of expansion of materials, it cannot be used for absolute density measurements. Therefore, a density determination at a known temperature must be coupled with the volumeter measurements to give all the desired data. The weight-loss technique using immersion in bromobenzene at room temperature proved to be satisfactory. The preliminary work that was done on this experimental program involved developing and calibrating the equipment, and measuring the densities and volume coefficients of expansion of cerium and some low-melting binary cerium alloys. The complications that are caused with the introduction of plutonium into the system were avoided until the equipment was proved to be satisfactory and until experience was gained in its operation. It is this first phase of the experimental work that is described in this report. DESCRIPTION OF EQUIPMENT AND OPERATING PROCEDURE The NaK volumeter is shown schematically in Fig. 1. Basically, the equipment consists of two weld-sealed stainless-steel containers of nearly identical volume. One container holds a tantalum crucible and the specimen being measured; the other contains a tantalum crucible and a tantalum specimen used as a control reference material. To avoid temperature gradients, the bombs are located in a copper block inside the furnace. Stainless-steel capillaries of equal length and volume connect each stainless-steel container to a glass viewing capillary. The stainless-steel containers, stainless-steel capillaries, and a portion of the glass capillaries are filled with NaK (22 wt pct Na-78 wt pct K). The NaK/gas interface in the glass capillary is viewed with a cathetometer which is accurate to *0.5 mm. The cathetometer readings are used to calculate the volume changes of the samples during a run. This volumeter is basically the same as that described by F. Knight in Plutonium 1960. 2 However, changes in equipment design and operating procedure were made to eliminate some major operating difficulties. These changes are summarized below. 1) In filling the manometer with NaK, gas was frequently entrained in the system. Evacuation of the system before filling failed to eliminate the en-

Jan 1, 1965

By Arthur Notman

THE COMMITTEE on Production Control of the Institute has accomplished little or nothing tangible during the last year. For this the chairman must accept responsibility and whatever praise or blame goes with it. However, we have all had plenty of opportunity to observe the results obtained by various producing groups in their attempts to regulate production to meet demand dur¬ing the last few years. It would be putting it mildly to say that these have not been such as to inspire confidence in the methods pursued. The present plight of the wheat, cotton, coffee and sugar growers; the oil, copper, lead, zinc and tin producers, to name a few of the unfortunates, suggests a common cause perhaps beyond their control. There is a growing tendency to question as outmoded the theories of laissez faire economics, with its laws of competition, supply and demand, with price as the automatic regulator. The position is maintained that something new should be substituted because these laws no longer work. Many solutions are offered, ranging in the world at large from the planned economy of Russia, with the profit element removed, to the military controlled economy of Fascism, and in our own country from voluntary curtailment to martial law. But one hardly feels driven by any irresistible logic to put his finger on any one of these proposals, and to say this is the one in which I believe. On turning to one's neighbors, one is still more confused by the realization that this intellectual uncertainty is wide-spread. Isolation or cooperation, protection or free trade, the gold standard, bimetallism or managed currencies, de¬flation or inflation, all have their proponents in whose eyes one or the other of these slogans will afford the panacea for all our ills.

Jan 1, 1933

By Chas. F. Jackson

IN these days the headlines and spotlight have been focused largely upon the new processes developed and new plants erected to meet the multiplied demands for mineral products required for prosecution of the war. By comparison, the less spectacular achievements of the miner, who is meeting the demand for raw material without which these processes and plants would be useless, have received little attention. Attendance at the mining meetings here reported was small, averaging about 35 to 40, but interest was as keen as ever, and evidenced to your reporter that the miner is no less on the job than is the metallurgist. It is evident that the mine operators are not neglecting any improved methods and practices in their struggle to produce more in the face of diminishing labor supply.

Jan 1, 1943

By John T. Ryan

FOR the first ten months of 1942, on which data are available at the time this is written, the coal-mining industry achieved a most creditable safety record, and ha1 figures for the year may show a record surpassing that of 1941 in which the industry reached the best accident rate in its history. The ten- month accident rate for both bituminous and anthracite mining in 1942 was 2.197 fatalities per million tons of coal mined, compared with a revised rate of 2.271 for the same months of 1941. The bituminous rate decreased from 2.139 in 1941 to 2.039 for ten months of this year, and the anthracite rate shows a reduction from 3.707 to 3.699 for the same period.

Jan 1, 1943

By A. U. Seybol

Eight binary iron alloys were examined after ion nitriding experiments to determine the behavior of the following elements: Al, Mo, Mn, Si, Ti, V,Cr, and C. Only Al, Cr, Ti, and V additions caused hardening in binary iron alloys. A few steels were examined to see the effect of Cr, Cr + Al, Cr + Ti, and Cr + V. It is suggested that a useful new class of ni-triding grade steels might be those containing about I pct V. The nitriding of steel, first described by Fry1 about 45 years ago, rapidly attained commercial application with very little knowledge of the fundamentals involved. While Fry,' in describing the status of nitriding in 1932, apparently correctly postulated hardening by precipitated nitrides, the details of the nitriding process were not understood, nor has the situation changed much since that time. It is also interesting to note that the compositions of some typical nitriding steels given by Fry at that time have changed little in the intervening years. Currently used nitriding steels owe their surface hardening to either chromium (as in 4340 steel) or aluminum plus chromium as in the Nitralloy grades, where both CrN and AlN appear to contribute to harden ing. Titanium additions have been studied experimentally, but thus far titanium steels have not won wide commercial acceptance. This subject will be expanded later. The orthodox ammonia nitriding process has been reviewed very adequately many times as in Jenkins3 and Case and VanHorn,4 and their is no need to outline the process here. Ion nitriding is not as well-known, although there have been several descriptions5-9 of the process given, sometimes with comparisons with the ammonia process. Most of these papers are primarily concerned with a description of the equipment, or of the physics or electrical engineering aspects of ion nitriding, but Noren and Kindbom9 gave the results of a metallurgical investigation using both processes. In brief, ion nitriding is carried out in a vacuum chamber from which the air is exhausted and replaced by a N2-H2 mixture, typically containing 10 to 20 pct N2, at about 5 to 10 torr pressure. While ammonia gas has also been used in ion nitriding, there is no evidence that ammonia makes any improvement in the ion nitriding process. A few hundred volts dc is applied between the grounded container wall (positive) and an insulated center post supporting the work (negative) to be nitrided. A glow discharge is created in the ionized gas, accelerating positive nitrogen ions to the work. These ions contain enough energy to form the normally unstable Fe4N "white layer", thus establish- ing surface nitrogen solubility characteristic of the a Fe/Fe4N equilibrium. This creates a substantial concentration gradient, driving dissolved nitrogen into the steel. The temperature employed is in the same range (around 500" to 550°C) as in ammonia nitriding, but because of factors which are not understood at present the nitriding time is ordinarily considerably reduced in ion nitriding. Other advantages have been cited,9 but it is not the purpose of the present work to contrast the two processes. The present objective was to examine the behavior of binary iron alloys during ion nitriding with respect to the microstructure, hardness level, and depth, and to examine some of these factors in steels as well. In this way it was hoped to be able to find out something about the individual role of these elements in steels. While all the work was done by ion nitriding, there seems to be no reason why any conclusions reached would not equally apply to ammonia nitriding, excepting only the kinetic aspects of the process. Another objective was an exploration of the critical-ity of the ion nitriding variables: gas composition, pressure, temperature, and time. EQUIPMENT AND MATERIALS The equipment used was substantially as described by Jones and Martin.8 The vacuum tank was about 12 in. in diam by about 18 in. high, and consisted of water-cooled stainless steel, with a single small window at the top for viewing inside. This sat on a heavy mild steel base equipped with the main pumping port, pressure control port, and vacuum gaging. A series of variable resistances was interposed between the glow discharge and a large-capacity -40 amp variable primary transformer feeding a 1000-v transformer, but 600 v were about the maximum ordinarily used. With the small l-in.-round, 4-in.-thick discs used for nitriding, the electrical load was usually about 500 v at 0.8 amp. The specimen temperature was controlled by a stainless-steel sheathed chromel-alumel couple, whose junction was in the steel stool upon which the flat discs were placed. These were ground through 400 Sic paper. Cycling of the temperature controller caused -0.2 amp variation in ion current, providing an ample control band. The binary iron alloys were made from vacuum-melted hydrogen-deoxidized electrolytic iron and alloys of 99.9 pct purity. Cast ll-lb-square tapered ingots were forged and hot-rolled to about 11/4-in.-diam rounds. Discs of 1/4 in. thickness by about 1 in. diam were machined from the rods for nitriding specimens. The following alloys were prepared: 1 pct each of Mn, Mo, Cr, Ti, Al, V, Si, and an Fe-0.8 pct C alloy. EXPERIMENTAL VARIABLES Of the variables total gas pressure, nitrogen partial pressure, temperature, and time, only nitrogen partial pressure was found to be critical to the operation. A critical nitrogen partial pressure was found corre-

Jan 1, 1970

By M. J. Marcinkowski, Gordon E. Lakso

An extensive investigation has been made of the deformation behavior associated with the Fe3Si super-lattice using transmission electron microscopy techniques. Above 243°K the stress-strain curve exhibits three stages. Stage I occurs at a very low stress level and is related to the generation of perfect superlat-tice dislocations. Stage II is characterized by an extremely rapid rate of work hardening and is associated with the Taylor type locking of these superlattice dislocations. Finally Stage III is related to dynamic recovery processes since the work hardening rate is very small. Below 243ºK, only Stage I is observed, but it occurs at a much higher stress level. This latter observation is related to the generation of imperfect dislocations in Stage I with the consequent production of second nearest neighbor antiphase boundaries. The reason for this is that insufficient thermal energy is available at these low temperatures to generate the complete and perfect superlattice dislocations. It has been shown that the fully ordered FeCo alloys, i.e., those possessing the B2 type structure, exhibit three distinct stages of work hardening whereas the corresponding disordered alloys show only one.&apos;" This difference in behavior between the disordered and ordered alloys has been attributed to the fact that dislocations in the former case travel only as ordinary 1/2ao(111) types whereas in the latter case the move through the lattice as coupled 1/2a0(111) dislocations separated by an antiphase boundary (APB), i.e., the so-called superlattice dislocation. Although some preliminary work has been carried out concerning plastic deformation in ordered alloys possessing the DO3 type superlattice,3 no detailed analysis similar to that described in Refs. 1 and 2 has been attempted. Specifically, it has been suggested that the superlattice dislocation in this particular type structure should consist of four ordinary 1/2ao<111> types bound together by first and second nearest-neighbor APB&apos;s. Fe3A1 and Fe3Si are the two classic alloys possessing the DO3 type lattice; however, because of the somewhat higher ordering energies associated with the FesSi alloy, which in turn assures that dislocations will travel through the lattice as perfect superlattice dislocations under at least some conditions, it was chosen for the present investigation. Because of the extreme brittleness of Fe3Si, all deformation was done in compression. Stress-strain curves were obtained using both polycrystalline samples as well as single crystals. In the latter case the crystals were oriented so that deformation could be controlled either by single or double slip. They were then wafered parallel to and at various angles to the operative slip planes. These wafers were in turn examined by transmission electron microscopy (TEM) techniques in order to determine the extent of the interaction from the dislocation configuration contained therein. EXPERIMENTAL PROCEDURE The alloys used in this investigation were arc melted under helium from electrolytic iron of greater than 99.90 wt pct purity and transistor grade silicon of 99.99 wt pct purity. A typical analysis of interstitial impurities showed 120 ppm 0, 15 ppm N, and 65 ppm C Because of the extremely low ductility of the Fe3Si alloys, it was necessary to spark cut 0.230-in. diam polycrystalline cylinders 0.400 in. long from arc-melted fingers using a thin-walled brass tube as a cutting tool. The polycrystalline alloys could not be recrystallized since very little strain was induced in preparation. However they were annealed at 1273°C for 15 min in evacuated vycor capsules to relieve any cooling stresses that may have developed during solidification and then air cooled. The resulting grain size of the alloy was 0.50 mm. According to warlimont4 1273ºC is just within the single phase field where FesSi possesses the DO3 type lattice. In addition because of this high critical ordering tem-ature, air cooling from this temperature was believed sufficient to fully order all of the Fe3Si samples used in the present investigation. For the same reason, no attempt was made to achieve any degree of disorder by quenching. In fact, rapid quenching from 1123°K caused cracking. Such cracking was first suggested by sato5 with respect to the experimental observations of Glaser and Ivanick.6 Single crystal compression specimens were spark cut from single crystal ingots grown in a Bridgman type furnace. The iron and silicon for the crystals was prealloyed by arc-melting two 130-g buttons which were cut into small pieces before remelting in the furnace. This procedure resulted in a long-range inhomogeneity of 0.5 at. pct Si between the top and bottom of the 2-in.-long single crystal ingot, which was assumed to be negligible in the present investigation. The single crystals, after orienting and spark-cutting, were about 0.37 in. by 0.37 in. in cross section and about 0.5 in. long. True stress-strain curves were obtained using an Instron Tensile Testing machine in conjunction with techniques described previously. 1,7 The strain rate was 0.05 in. per in. per min. Prior to testing, the ends of all the compression cylinders were hand polished using a special jig to insure parallelism after which the sides of the samples were electrochemically polished to eliminate stress risers and to facilitate slip line observations. Test temperatures between 77" and 823°K were obtained using various cooling and heating media as described in Ref. 7 while at the upper end of this temperature range, a mixture of equal

Jan 1, 1970

By E. Miller, R. Geffken, K. L. Komarek

The thermodynamzc properties oJ liquid Cd-Sb alloys were investigated using the cell arrangement measurments were obtained every 2°C at a heating and cooling rate of 12°C per hr and at equilibrium every 2O0C frorn 500°C down through the stable liquidus. The S-shaped asCd US composition curve was used in the cotnposition regzon near Cd,Sb, to calculate a tempeerture-dependent inleraction coefficient from quasichemical theory. Rapid changes in a scd were observed at a transition temperature varying from 400" to 465°C depending on con/kosition. It could not be determined if the changes in aScd were discontinuous, but tlze composition dependeke of the magnitude of the change is indicative of a second-order phase transformation in the liquid. The values of the experimental changes in ASCd are in agreement with calculations from the slope of the transition temperature, using the concept that a second-ovdev phase transition occurs in liquid Cd-Sb alloys. II is suggested that the transformalion is associated with the formation of Cd4Sb3 molecules in the liquid. ThE structure of liquid alloys is the subject of many investigations. X-ray, resistivity, and thermody-namic data have been interpreted as indicating varying degrees of short-range order in the liquid in alloy systems forming inter metallic compounds. In general, the melting process is not a transition from an ordered to a completely disordered state, but some degree of order is retained in the liquid. Maximum ordering in the liquid state occurs close to the melting temperature of the compound and the arrangement of atoms becomes more random at higher temperatures. Of special interest in this respect is the Cd-Sb system. It is one of the few metallic systems which form both stable and metastable compounds when liquid alloys are cooled at normal rates. The stable system exhibits an intermetallic compound, CdSb, melting at 459"c.l A second compound, CdrSbs, has also been reported,&apos; melting close to this temperature. The metastable system has one compound, CdsSbz, melting at 420"c.I Resistivity measurements on liquid Cd-Sb alloys close to the liquidus temperatures have been interpreted in terms of a complex ordering behavior which changes rapidly with increasing temperature.3 The resistivity-composition curve is characterized by two maxima corresponding in composition to CdSb and CdsSbz. The resistivity-temperature plots show sharp breaks for alloys in the composition range of 45 to 70 at. pct Cd on cooling through a transition temperature close to the stable liquidus. Fisher and phillips4 investigated the influence of temperature and composition on the viscosity of liquid CdSb alloys. The viscosity of some alloys increases sharply on supercooling below the stable liquidus. A maximum in the viscosity-composition curve occurs at the composition CdSb. The thermodynamic properties of liquid Cd-Sb alloys have been investigated by Seltz and ~e~itt&apos; and Elliott and chipmane by the electromotive-force method and their results are in good agreement. However, these investigations were carried out at temperatures well above the liquidus temperatures of the alloys, and the temperature coefficients of the electromotive force, dE/dT, were obtained from experimental points for each alloy at a few temperatures considerably above the liquidus temperature. Scheil and ~aach&apos; investigated the thermodynamic properties of this system by the dew point method in the temperature range from about 100°C above the stable liquidus down into the supercooled liquid region. They reported several anomalies, i.e., the activity of a melt on heating differed from that on cooling, and the activity increased sharply in the limited temperature interval immediately above the liquidus temperature of the stable alloy, followed by a sudden decrease below the liquidus. Values obtained on heating and cooling were not in agreement. A reinvesti-gation of a few alloys by Scheil and Kalkuhl&apos; by the electromotive-force method failed to confirm these observations. The authors concluded that the anomalies were due to inhomogeneities in the starting alloys and they discarded their previous results. The present investigation was undertaken in order to obtain thermodynamic data close to the liquidus temperature and in the supercooled region where the anomalies were originally reported, employing the electro motive-force method. This method is quite precise and will most easily permit observations of small changes in activity and partial molar entropy with temperature. Measurements were taken every few degrees so that the dE/dT values could be calculated over the entire temperature range and small changes in the thermodynamic properties close to the liquidus temperature could be observed. I) EXPERIMENTAL PROCEDURE Specimens were prepared from 99.999+ pct Cd and Sb (Cominco). Surface oxide was removed by scraping and then melting the metals under vacuum and filtering through Pyrex wool. Appropriate amounts of the metals were weighed on an analytical balance to k0.1 mg, sealed in double Pyrex capsules under vacuum,

Jan 1, 1968

By R. W. Fountain, M. Korchynsky

The precipitation phenomena occurring in cobalt-tantalum alloys have been investigated in the temperature range frm 500" to 1050°C by correlating the results of metallographic, X-ray, micro-and macrohardness, and electrical resistivity studies. The property andmacrohardness,changes were found to depend on 1) general precipitation, and 2) lamellar precipitation. Two new intermetallic phases have been identified: 1) a Co3Ta, a metastable ordered face-centered-cubic compound, and 2) a stable ß Co3Ta phase of hexagonal structure. In addition, the previously reported Co2Ta phase was found to exist in two allotropic modifications: the hexagonal MgZn,-type and the cubic MgCu2-type Laves phases. SINCE a large variety of structures can result as a consequence of the decomposition of a solid solution, predictions on the nature of property changes are difficult, if not impossible, to make. For any rational attempt to correlate properties and structures of a precipitation-hardenable alloy, a detailed understanding of the kinetics of decomposition and morphology of phase separation, as well as knowledge of phase relationships, appears to be prerequisite. Information of this type has been accumulated in the past for many alloy systems, both of theoretical and pastforpractical importance.1,2 Although the presence of intermetallic compounds has been reported in cobalt-base alloys,3 the amount of published information on precipitation-hardenable cobalt-base systems is very limited. A survey of the binary phase diagrams of cobalt indicates that cobalt-tantalum alloys might be of interest as typical of other cobalt-base systems in which Laves phases of the A,B type can be precipitated from solid solution. The present work has been undertaken, therefore, to study the kinetics and morphology of the precipitation reaction in this system and to establish a base for a correlation between the structural aspects and properties in this class of alloys. PREVIOUS WORK The only available phase diagram of the cobalt-tantalum system is based on the work of Koster and Mulfinger. According to these authors, the maximum solubility of tantalum in cobalt is about 13 pct (at 1275°C) and. less than 7 pct at room temperature. Tantalum additions lower the temperature of allotropic transformation of cobalt (about 420°C), and at 7 pct Ta, the high-temperature face-centered-cubic modification (ß cobalt) is retained at room temperature. The precipitating phase was originally designated as Co5Ta2 compound (55.2 pct Ta, about 1550°C melting point), but subsequent investigations by wallbaum5" identified this constituent as the A,B-type Laves phase. Wallbaum&apos;s data indicate that there are two modifications of this intermetallic compound: one richer in cobalt (Co2.2 Tao.8)of the hexagonal MgNi, type; and another of a higher tantalum content (Co2Ta) of the cubic MgCu, type. On the other hand, Elliott7 found that the cobalt-rich alloy (CO2.10,Tao.~l) was predominantly the cubic MgCu, type at 800°C and a mixture of both the MgCu2 and the hexagonal MgZn,-type Laves phases at 1000°C. At 1200°C, Elliott found only the MgZn, type while at 1400°C, he observed only the MgCu2 type. At the stoichiometric composition, Co2Ta, Elliott reported only the cubic MgCu2-type Laves phase in the temperature range of 600oto 1600°C. The precipitation of the cobalt-tantalum intermetallic compound is accompanied by a marked increase in hardness. According to Koster&apos;s4 data, the Brinell hardness of an 8 pct Ta-Co alloy increases from 230 to 340 upon short-time aging at 800°C. EXPERIMENTAL PROCEDURE The binary cobalt-tantalum alloys investigated contained 5, 10, and 15 pct Ta. The range of tantalum additions was thus slightly broader than the reported minimum and maximum solid solubility limits of tantalum in cobalt (7 and 13 pct, respectively)4 The alloys were vacuum-induction melted in a magnesia crucible using cobalt rondelles and technically pure tantalum sheet as raw materials. Deoxidation of the melt was accomplished with carbon, and the chemical analysis of the alloys is given in Table I. The effect of isothermal aging treatments on the progress of precipitation was studied on samples cut from cast ingots. These samples were solution treated for 2 hr at 1250°C and water-quenched. Aging was conducted in the temperature range from 500" to 1050°C for periods between 15 min and 1000 hr and followed by water-quenching. To prevent contamination from the atmosphere, all samples were sealed in evacuated Vycor or quartz tubes for heat-treatments. For solution treatment, argon at 0.2 atmospheric pressure was introduced prior to sealing of the capsule to prevent collapse at high temperature, and titanium sponge was placed at one end of the capsule to act as a getter. MACROHARDNESS The effect of aging on Vickers hardness (Dph) of

Jan 1, 1960

By Claudio Barsotti, Leonard C. Kitchener

INTRODUCTION The major mining operations of the Ontario Division of Inco Metals Company are located in the Sudbury Basin. Around the rim of this geo- logical formation and within thirty miles of the City of Sudbury are located eleven under- ground mines of the Company, two of which are on standby. In addition, there is one mine in Northwestern Ontario at Shebandowan, 1127 Km (700 miles) northwest of Sudbury. In 1980 ore production totalled 10.6 x 10 mt (11.7 million tons) from underground and open pit operations. Underground mining methods include blasthole, vertical retreat, sublevel caving, cut-and-fill and undercut-and-fill. Inco reduction operations in the Sudbury area include two concentrators, one smelter, one iron ore recovery plant, a copper refinery a nickel refinery and a high purity plate rolling mill. As well, an electrolytic nickel refinery is located on Lake Erie at Port Colborne, near Niagara Falls. In the Sudbury District, Inco employees total 14,278 of whom 6,490 are directly employed in the mining and milling operations. I T H DRILLING Background - The use of long blastholes in underground operations at Inco mines in the Sudbury district started more than 30 years ago at the Levack Mine. At that time, diamond drills were used to mine ore by open stoping and for pillar recovery. By the 1950&apos;s the concept had been extended to all mines. The heavy percussion drill was also developed by this time and led to the acceptance of the 11.43 cm (4% in.) piston diameter drifter for bar and arm and fan drill applications. The use however, of the nominal 5.08 cm (2 in.) diameter blastholes drilled radially from the level or sublevel causes overdrilling at the periphery. As well, the smaller holes are subject to hole deviation, are difficult to drill beyond 38.1 m (125 ft.) and require the need for several drilling horizons or sublevels. The need to improve blasthole stoping techniques and our experience with large diameter blastholes in open pit mining led to the trial of an I T H drill in 1962. The test was unsuccessful however, since button bits were not available at the time and the tungsten carbide cross bit experienced short life, gauge loss, and caused hole deviation and poor penetration rates. The successful application of the raise borer beginning in 1964 and the ability to drill 20.32 cm (8 in.) to 27.94 cm (11 in.) diameter pilot holes led to the development of smaller, more portable, rotary drills for blasthole mining. As a result, a mining method based on the use of 20 cm (7 718 in.) diameter, 60.1 m (200 ft.) long rotary blastholes was developed and tested successfully at our C.C.North Mine. Between 1972, when the method was first tested, and 1973 over 4572 m (15000 ft.) of large holes were drilled with rotary drills in the recovery of 175,960 mt (194000 tons) of primary stoping and pillar remnants. A new mining method was developed that made use of this large hole drilling equipment. Instead of longhole carbide drilling by bar-and-arm or fan drill set-ups at sublevels, the large diameter holes were drilled full stope height from the top sill, which substantially reduced development, drilling time and improved fragmentation. These drills however, were difficult to move and set-up, and had a high maintenance cost and low productivity. The capital outlay and extensive technical development required to improve these drills and reduce the high drilling costs however, was economically unattractive. New development in drills and button bits INTRODUCTION The major mining operations of the Ontario Division of Inco Metals Company are located in the Sudbury Basin. Around the rim of this geo- logical formation and within thirty miles of the City of Sudbury are located eleven under- ground mines of the Company, two of which are on standby. In addition, there is one mine in Northwestern Ontario at Shebandowan, 1127 Km (700 miles) northwest of Sudbury. In 1980 ore production totalled 10.6 x 10 mt (11.7 million tons) from underground and open pit operations. Underground mining methods include blasthole, vertical retreat, sublevel caving, cut-and-fill and undercut-and-fill. Inco reduction operations in the Sudbury area include two concentrators, one smelter, one iron ore recovery plant, a copper refinery a nickel refinery and a high purity plate rolling mill. As well, an electrolytic nickel refinery is located on Lake Erie at Port Colborne, near Niagara Falls. In the Sudbury District, Inco employees total 14,278 of whom 6,490 are directly employed in the mining and milling operations. I T H DRILLING Background - The use of long blastholes in underground operations at Inco mines in the Sudbury district started more than 30 years ago at the Levack Mine. At that time, diamond drills were used to mine ore by open stoping and for pillar recovery. By the 1950&apos;s the concept had been extended to all mines. The heavy percussion drill was also developed by this time and led to the acceptance of the 11.43 cm (4% in.) piston diameter drifter for bar and arm and fan drill applications. The use however, of the nominal 5.08 cm (2 in.) diameter blastholes drilled radially from the level or sublevel causes overdrilling at the periphery. As well, the smaller holes are subject to hole deviation, are difficult to drill beyond 38.1 m (125 ft.) and require the need for several drilling horizons or sublevels. The need to improve blasthole stoping techniques and our experience with large diameter blastholes in open pit mining led to the trial of an I T H drill in 1962. The test was unsuccessful however, since button bits were not available at the time and the tungsten carbide cross bit experienced short life, gauge loss, and caused hole deviation and poor penetration rates. The successful application of the raise borer beginning in 1964 and the ability to drill 20.32 cm (8 in.) to 27.94 cm (11 in.) diameter pilot holes led to the development of smaller, more portable, rotary drills for blasthole mining. As a result, a mining method based on the use of 20 cm (7 718 in.) diameter, 60.1 m (200 ft.) long rotary blastholes was developed and tested successfully at our C.C.North Mine. Between 1972, when the method was first tested, and 1973 over 4572 m (15000 ft.) of large holes were drilled with rotary drills in the recovery of 175,960 mt (194000 tons) of primary stoping and pillar remnants. A new mining method was developed that made use of this large hole drilling equipment. Instead of longhole carbide drilling by bar-and-arm or fan drill set-ups at sublevels, the large diameter holes were drilled full stope height from the top sill, which substantially reduced development, drilling time and improved fragmentation. These drills however, were difficult to move and set-up, and had a high maintenance cost and low productivity. The capital outlay and extensive technical development required to improve these drills and reduce the high drilling costs however, was economically unattractive. New development in drills and button bits

Jan 1, 1981

By K. Harms, T. D. Jones

TO unload large tonnages of lead bullion cast in 100-lb. bars is a problem which has confronted the lead refineries for many years. The bars, on arrival, must be restacked for unloading by truck or hand-charged to charging machines. Selected crews of labor, capable of working at sustained speeds for five- or six-hour periods, are required for this exhausting task. Due to the fatigue involved crew personnel changes rapidly. During the war it became increasingly difficult to maintain crews, especially in critical labor areas, so that the development of casting and shipping ten-ton lead blocks from the smelters to the refineries became a must in our operating program. For many years lead refineries, when making interdepartment or intradepartment transfers, have cast lead blocks weighing five or ten tons which are easily handled by crane by merely attaching the crane hook to a steel anchor embedded in the frozen lead blocks. In previous years, the practice was to use regular smelter slag pots which, due to their rounded shape, produced what were called "buttons" by the refinery personnel. The button-type blocks were unsafe as they rolled and tipped easily and were unsatisfactory for stacking since no piling pattern could be followed. To remedy this situation, flat-bottom molds came into general use and later the bottoms were made concave to prevent slipping.

Jan 1, 1946

By Paul Foote

SEEBECK discovered, in 1821, that if, in a closed circuit of two metals the two junctions are at different temperatures, an electric current will flow in the circuit. In the case of an iron and a copper wire, for example, current will flow from copper to iron at the hot junction, or from iron to copper at the cold junction. Two factors combine to cause the current. An electromotive force exists between the two metals, the magnitude of which, depends upon the temperature and upon the metals; this is called the Peltier e.m.f. If a single wire of homogeneous material is heated at one end, an electromotive force is developed between the ends of the wire, the magnitude of which depends upon the metal and upon the difference in temperature; this is known as the Thomson e.m.f: The total e.m.f. acting in the circuit is the sum of the Peltier e.m.f. at the two junctions and the Thomson e.m.f. in each wire, consideration being given, of course, to the algebraic signs of the four e.m.f.&apos;s. The total electromotive force thus depends upon the difference in temperature of the two

Jan 9, 1919

By Y. C. Liu, R. H. Richman

Deformation and recrystallization textures of the a solid solutions of Cu-P, Cu-As, and Cu-Sb alloys are examined as a function of composition. It is found that the deformation texture of copper is unckanged up to a composition of 0.43, 0.41, and 0.24 at. pct of phosphorus, arsenic, and antimony, respectzvely, and then the transition to the 70 : 30 brass type of deformation texture proceeds linearly as the logarithm of the solute content. Recrystallization textures consist of strong, new components that do not all bear the usual<111> rotational relation to the deformation components. The dependence of the deformation texture transitions and the recrystallization orientations upon composition and solute-element type is discussed. A systematic evolution of individual recrystallization components in the annealing texture of copper was portrayed as a function of germanium or tin content in a previous study.&apos; Similar patterns of tex-tural change have been observed with copper-zinc alloys,2 and in less detailed studies of other systems.3,4 In fact, most of the literature dealing with preferred orientations in copper alloys indicates that the influence of solute elements upon textures in copper is of one general type. As the alloy content of copper is increased, the deformation texture changes from the copper type to the 70:30 brass type, and the annealing texture undergoes a comparable change from the (001) [ loo] orientation of unalloyed copper to the {113} <211> type of 70:30 brass, with the notable exception of copper alloyed with Periodic Subgroup V-B elements.4-8 In almost every case it is possible to describe the reorientations after annealing as 30 to 40 deg rotations about <1ll> poles of the deformation components. Since there is apparently not much difference in the final textures of the copper binary systems already investigated, only a limited variety of preferred orientations has served as the basis for current theories of the origin of annealing textures. In order to test the validity of the proposed theories, and the possibility that the <111> rotations are not unique, it would be most desirable to study the reorientation relationships of additional, and heretofore unanalyzed, recrystallization components if such components exist. Examination of the literature reveals a good deal of uncertainty concerning preferred orientations in copper alloyed with elements in Subgroup V-B of the Periodic Table. Phosphorus is known to inhibit the cube texture in copper when present in amounts as low as 0.01 wt pct,8 but the recrystallized matrix that occurs instead of the cube orientation was reported as either random or weakly textured, with orientations not observed in Cu-Zn, Cu-Ge, or Cu-Sn alloys.4-9 A Cu-0.75 at. pct As alloy apparently contained, along with the (001)[100] and (113) <211> type of recrystallization components, {110} <112> and (110) <001> components, whereas an almost random distribution of orientations was found in alloys of higher arsenic content.4 A {110} <001> component also appeared in rolledand annealed Cu-Sb alloys, but otherwise the recrystallization textures of Cu-Sb alloys seem to con-

Jan 1, 1962

By Harry M. Mikami, A. Gene Sidler

Chemistry of the evolution of materials in contact with copper converter tuyeres is delineated by means of analyses of periodic punch rod samples taken during a converter cycle. Lining samples from known peripheral and end locations from three converters were investigated chemically and petrographically. One set of eight specimens representative of all lining parts was removed for study before completion of the campaign. Purely surface removal by slag action is minor. Slag filling of interconnecting cracks extending to the hot face results in a "stoping&apos;&apos; action which shapes the hot face contour and is a significant factor. Major wear mechanism is believed to be copper metal slabbbing caused by metal first penetrating joins and invading fractures or impregnating brick structure laterally from the joints. Importance of lining design and joint fit are emphasized. New laboratory tests are indicated. In the copper converter, molten matte, which is essentially a solution of iron and copper sulfides, is blown with air to produce blister copper. During the first stage of the process the FeS component is oxidized to SOz and FeO, the latter combining with a siliceous flux to form a predominantly ferrous silicate slag. Successive increments of matte and flux are charged, blown, and skimmed of slag until sufficient CuzS ("white metal") has accumulated. This white metal is then blown to copper metal in the final or blister-forming stage by the oxidation of sulfur to SOz and the reduction of combined copper to metal. The reactions of both stages are exothermic so provide the required heat. Temperature is controlled by cold scrap copper, flue dusts, smelter reverts, and so forth. Considerable vari- ation in practices occur depending on the type of converter, grades of the matte and flu, and other factors. Lathe and Hodnett&apos;s&apos; survey of world converter practices gives much information on these variations and their effects on the refractories. Principles of converting chemistry are presented by Newton and wilson,&apos; Ruddle,&apos; and schuhmann. Most copper converting occurs within the temperature range 2100" to 2370°F although individual smelters report1 ranges from as low as 1700" to 2240°F to a high of 2200" to 2400°F. Temperature intervals reported from beginning to end of blow varied from 45" to 540°F. Average temperature range was 2030" to 2260°F and the average interval 250°F During the matte-blowing stage varying amounts of magnetite (FeO.Fe,O,) are formed in the slag as suspended crystals and also the liquid portion of the slag will contain, in addition to ferrous silicate, some Fe20s which adds to the potential magnetite formation if the temperature falls. This is a component of the so-called "dissolved magnetite" often referred to in the literature. Although the slag may contain minor amounts of CaO, A1209, MgO, and alkalies, the principal components are Fe0-Fez03-SiO,. The phase equilibria relationships of this system have been elucidated by Muan~ and Schuhmann, et a1.&apos; These data and estimates of converting atmospheres by schuhmann4 are useful tools in studying slag behavior. It would appear that in many cases reported magnetite contents of slags are apparently higher than actually is present at operating temperature. This is probably because much of it is formed during slag solidification. The quaternary systems which have Mg-0,1,0,&apos; and addition to iron oxides and silica are also of interest in considering the reactions of the slags with basic refractories. The formation of magnetite has an important interrelationship throughout the pyrometallurgy of copper (Mossman,&apos; Gronningsater and Drummond," Ruddle,&apos; Elwood and Henderson") but its presence in the converter particularly relates to operating efficiency and lining life in certain instances. Archi-

Jan 1, 1963

By H. H. Kellogg

A model of the slag-fuming process for recovery of zinc oxide fume from lead blast furnace slags, adapted to solution by a digital computer, is presented. The model incorporates the variaticm with time of the following: the fuming of zinc and lead, the change in the ferrous-ferric ratio in the slag, the transfer of sulfur to and from the slag, the temperature of the liquid slag, the temperature of the gases and fume which exit to the flue, the heat losses to the water jackets, and the amount of frozen slag on the water jackets. The assumptions which underlie the model-some of which are but crude approximations—are discussed. Despite some obvious shortcomings, the model simulates faithfully many of the important features of practical slag-fuming operations. The behavior of the model is compared with the operation of the American Smelting and Refining Co. fumzace at El Paso, Tex. The model is used to predict the effects on performance of changes in the coal rate, the temperature of the secondary air, and the composition of the coal. THE fuming of lead blast furnace slag for recovery of zinc oxide is standard practice today, and it has been the subject of several previous attempts at mathematical process analysis.&apos;-&apos; The mathematical process model described in this paper incorporates many of the features from the earlier studies, but it is a far more complete and realistic representation of the commercial process in that the following additional features have been included: the fuming of lead as well as zinc; the transfer of sulfur between slag and gas; the addition of slag feed in batches, over a period of time; tapping of the final slag over a period of time; the change of slag temperature with time. The additional features of the present model add greatly to the mathematical complexity, but this difficulty has been obviated by programming the model for solution by a digital computer. The IBM 7094 computer solves the model for one operating cycle of the fuming furnace in less than 1 min. It is doubtful if the same calculations could be completed with the aid of a desk calculator in less than a month. The computer program, written in the Fortran IV language, is too lengthy for presentation here.* Instead, this paper As shown in the sections which follow, it does simulate with remarkable faithfulness most of the known behavior of the industrial process. On the other hand, the model contains several gross simplifications of both the chemistry and heat balance, necessitated by the lack of more exact knowledge. In addition to these known weaknesses, it is not unlikely that those more intimately acquainted with industrial practice than the author will find other additions to or modifications of the model which will improve its utility and reliability. CHEMISTRY In brief outline, the present model treats the fuming furnace as two units, A and B, in series. In A the batch of slag reacts with the continuous stream of air (primary and secondary) and fuel injected at the tuyeres, to produce a stream of hot, reduced gases containing zinc vapor. The zinc content of both the slag and the product gas changes with time because of the batch nature of the process. Unit A is called the "lower furnace" in this paper; physically, it is considered to be that part of the fuming furnace which lies below the charge port. In B, the "upper furnace", the product gas from A is burned with the stream of "tertiary" air, to produce zinc oxide fume. The performance of B also depends on time because of the time dependence inherited from the product gas of A. The rate behavior in the lower furnace determines the important features of the process—the rate of elimination of zinc and lead from the slag, and the amount of fuel required for this purpose. Bell, Turner, and peters&apos; published the first useful model of the lower furnace. They employed the assumption that, at any instant of time, the slag and reduced gas reach a state of equilibrium, according to the reactions: They cited only indirect evidence in support of their assumption of slag-gas equilibrium, yet several more recent laboratory studies of the activity of zinc oxide in slags4-8 have produced evidence which supports their view. On first acquaintance it seems unlikely that a high-output "rate" process like slag fuming would even approach an equilibrium state. The author, in an earlier study,&apos; established, however, that the gas-slag interface in a fuming furnace was capable of such high mass-transfer rates that a close approach to equilibrium between gas and slag was quite probable. In devising the present model it was decided to assume a state of equilibrium between slag and gas at the outset, and then to modify this assumption as necessary in order to make the model agree with the be -havior of the actual process. Up to this time the assumption remains a part of the model, since no behavior

Jan 1, 1968

By D. J. Schmatz, H. I. Aaronson, H. A. Domian

Diffusion kinetics in disordered hcp Cd-Mg alloys have been investigated by means of the Kirkendall effect and concentration-penetration curves determined with an electron-microprobe analyzer. Self-diffusion coefficients of both species were determined at the three marker compositions obtained, averaging 27.6, 46. 7, and 78.1 at. pct Mg, by means of the Darken analysis. These coefficients were then corrected for the unequal and concentration-dependent partial molar volumes of the two elements with the Balluffi analysis, and for the vacancy flux effect by the Manning analysis. The latter correction reduced the Balluffi correction produced larger changes in the self-diffusiv-ities; neither, however, produced statistically significant changes in the Do&apos;s or the H&apos;S. The most striking result of this investigation is that at all three compositions and at all temperatures studied both the uncorrected and corrected self-difjusivities of magnesium are higher than those of cadmium. The Cd-Mg system is the first one found in which the higher melting, lower vapor pressure element diffuses more rapidly. Both an empirical correlation due to Toth and Searcy and considerations of the atomic mechanism of diffusion indicate that this anomaly is probably due to a comparatively low value of the activation energy required for a magnesium atom and a vacancy to exchange sites, perhaps occasioned by the higher compressibility of magnesium atoms. KIRKENDALL effect studies have been previously reported for only two hcp solid solutions: the E phase of the Zn-Cu system1 and the a phase of the Cd-Hg system.&apos; In neither investigation were the marker-movement studies supplemented with the concentration-penetration curve determinations necessary to evaluate self-diffusivities by means of the atano and the Darken analyses. The present program was undertaken to obtain both types of data on a hexagonal solid solution in order to provide more detailed information relevant to the mechanism of diffusion in this type of lattice. The Cd-Mg system was chosen for this study because the disordered solid solution extends across the entire phase diagram at temperatures above 253"c5 and the substantial difference in the melting points of the component pure metals promised that marker movements would occur at reasonably rapid rates should the diffusivities of the two species be as unequal as might be anticipated. The experimental convenience of the relatively low melting points of cad-miun and magnesium and the availability of extensive and accurate activity data6 (required for application of the Darken analysis) were additional reasons for selecting this alloy system. Since the anisotropy of diffusion is not large in either pure cadmium7 or pure magnesium,&apos; the diffusion couples were prepared from polycrystalline components. The presence of a well-defined texture in the couples—the c axis of individual crystals tended to be normal to the diffusion direction— however, provides a fair degree of crystallographic definition to the data obtained. The principal (and entirely unexpected) finding of this investigation, that magnesium, the high-melting low-vapor pressure element, diffuses more rapidly than cadmium, in contradiction to a broad range of results in fcc and bcc alloys, as well as in the previously studied hcp alloys,172 makes the self-diffusivity determinations of immediate interest in understanding the origin of this anomalous result. EXPERIMENTAL PROCEDURE The cadmium (Belmont Smelting and Refining Co.) and magnesium (Dow Chemical Co.) used in this study were both of 99.99 pct purity. Alloys containing 51.0 and 65.6 at. pct Mg were prepared from these materials by melting under a MgC12-base flux in a high-purity graphite crucible. These alloys were subsequently hot-worked and then homogenized in a helium atmosphere at temperatures close to their solidus points. Sandwich-type diffusion couples of the type g/d/g were prepared from the pure metals by solid-state diffusion. Two-piece alloy couples of Mg/65.5 at. pct Mg (Mg/gCd) and Cd/51.0 at. pct Mg (Cd/CdMg) were welded by a liquation technique. The individual components of both types of couple were initially cylinders 1.27 cm in diam and in length; the ends of these cylinders were machined accurately flat and parallel. For both welding techniques, the pure cadmium cylinders and the alloys were chemically polished in a mixture of 40 pct ethyl alcohol, 40 pct hydrogen peroxide (30 pct conc), and 20 pct nitric acid,g while those of pure magnesium were polished in a solution of 10 pct nitric acid in ethyl alcohol.&apos; Immediately afterwards, both metals were rinsed in freshly distilled acetone, and then in similarly purified methanol.&apos; The Mg/Cd/g couples were assembled in a carefully cleaned stainless-steel welding fixture, in which a screw operating through a self-centering arrangement permitted a controlled pressure to be exerted upon a couple prior to welding.&apos;&apos; Tungsten marker wires 0.005 cm in diam were placed at the d:g interfaces of some of these couples, and imbedded in the couples during the application of pressure. As soon as a couple had been assembled, the welding fixture was inserted into a Pyrex capsule containing a packet of zirconium chips at each end. The capsule

Jan 1, 1967

By Francis Lucas

EACH year we gather in this auditorium to honor the memory of a. distinguished American metallurgist and educator. I cannot bring to you reminiscences of Prof. Henry Marion Howe as other lecturers have done. It was not my good fortune to enjoy the-privilege of studying and working under his direction. As I have reflected on the published works of Professor Howe, it has seemed to me that his mind was trained on the nature of metals and on the mechanism which produced known but unexplained effects. He was interested in controlling and regulating the causes so as to produce specific effects, useful in serving mankind. I recall an afternoon in May, 1925, when, at the invitation of Mrs. Howe, I visited his former home, Green Peace at Bedford Hills, N. Y. The purpose of my visit was to receive at the hands of the widow an engraving of Professor Howe, a reproduction of a painting from life. Mrs. Howe showed me his study. The walls of this large attractive room, brilliantly illuminated by the spring sunshine, were literally covered with the scrolls of honors and of decorations which had been conferred on Professor Howe by governments, academies, universities, societies and institutions the world over. As we walked about the room, she pointed out the significance of each honor and recited a few details of each occasion. I sensed the pride with which Mrs. Howe, then in the late autumn of her life, told me of her husbands&apos; achievements, of his struggles, of his disappointments and of his successes. There was a surprisingly familiar note in the recital to which I was listening. I &apos;have found the same theme running as a disconnected thread through the written accounts of the lives of most men of science. We then went to the drawing room to chat for a few minutes before I said my farewells. As we seated ourselves, Mrs. Howe turned to me and asked: "Mr. Lucas, what of this great microscope of yours? Cannot it be applied to the study of disease? What a great blessing it would be if it could be directed to relieve the suffering of mankind."

Jan 1, 1931

By H. W. Mossman

Three aspects of magnetite smelting are discussed. The first is the working out of equilibrium conditions for eliminating sulfur. The second is the influence of magnetite solubility on the difficulty of tapping the reverb matte. The third is an approximation of the equilibrium conditions in the reverb gases which govern whether magnetite is mode or reduced in the reverb slag by these gases and by any iron sulfide in the slag. MAGNETITE has had a varied history in the Hurley Smelter since its start in 1939. Magnetite determinations on the smelter products are made regularly only on the monthly composite samples. Variations on the monthly averages are shown in Table I. Magnetite which drops from the slag and matte in the reverb has some slight bottom buildup which comes and goes, but no substantial accumulation from this source has been found at the end of a normal nine months&apos; furnace campaign. However, there has been some low grade magnetite bearing material mixed with considerable A1,0,, which has slid down from the bottom of the sloping flue between the reverberatory furnace and the waste heat boilers. This accretion has required drilling and blasting near the skimming end of the furnace. The magnetite has interfered with tapping at times. When the smelter was first started, tapping trouble from magnetite was extremely severe. Increasing the reverberatory furnace temperature by putting in an air preheater and a Dutch oven has helped greatly, although there still is occasional tapping trouble. When the present series of physical chemistry articles on copper smelting started coming out in 1950, they were read with interest, but no immediate application was seen for them. Results of some laboratory work in 1952 aroused a much stronger interest in this physical chemistry. A series of melts was made on some converter slags, which had magnetite in very large grain sizes, with the object of reducing the grain sizes in the slag, as it was known that it was easier to handle in the reverb in that condition. Anything done in the tests greatly reduced the grain sizes—even in the controls, where nothing was done except melt the slag and cast it. There was more magnetite in the slags after the tests than before, and with wide variations. There were no obvious reasons lor much of what happened in these tests. Much of the base material published in English in this field was made available for study. Recalculations were made on many of the type problems, and part of the data was reduced to local temperatures and compositions. Explanations were found for what happened in the 1952 series of tests on converter slags, and the same principles turned out to be a description of much of what magnetite does in the reverb. This article is to present the results of that study, from the viewpoint of applying the technical material in definite numerical form to the operating conditions in both the converters and the reverberatory furnaces at the Hurley smelter. Table I. Magnetite Variations on Monthly Averages, 1939 to 1955 Pet Magnetite Lowest Highest Average Converter slag 13.6 43.3 25.4 Roverb slaa 2.7 20.9 8.7 Matte 28 15.9 98 In general it was found that magnetite is made or reduced in both the converters and the rever-beratory furnace, depending on variations of temperature, matte composition, and reverb gas composition occurring in ordinary plant operation. Within reasonable limits, the field conditions for formation or reduction can be predicted, and probably can be set up and maintained. Converter conditions affecting magnetite formation can be put into numerical values better than for the reverb from purely technical calculations. The converter can be operated so as to keep the magnetite in the slag down to between 12 and 14 pct and still give satisfactory life for the converter brick. This depends upon having converter flux available which will make a slag with a good separation without raising the temperature too high. In the Hurley reverb and others with similar conditions, it is likely that a compromise of conditions will give a reasonably good control of combustion and still keep the magnetite from building up on the bottom. This discussion consists of three main parts. The first is the working out of the equilibrium conditions in the converter for determining in which direction the reaction 3 Fe,,O, (s) + FeS (1) F? 10 FeO (1) + SO, will go under actual converter operating conditions. The second deals with the influence of the solubility of magnetite in the slag and matte in the reverb on the difficulty of tapping matte. The third is an approximation of the equilibrium conditions in the

Jan 1, 1957

By E. W. Engelmann

A NEW and interesting type of drier has been developed and operated at the Magna plant of the Utah Copper Co. for the past year for the drying of a filtered concentrate in the molybdenum recovery plant of this company. The several units installed have ranged from 12 to 30 in. in width, and from 14 to 30 ft. long. Their economy was immediately apparent after the first one was installed. The machine is not only low in capital cost, but has proved efficient for the drying of fine concentrate at low operating cost. The Utah vibrating drier consists of a steel conveyor trough supported on flexible reeds from a structural steel foundation anchored in concrete. The steel pan, which is also the drying surface, is vibrated by a heavy Utah electromagnetic vibrator fastened either to the head or discharge end of the pan. The vibration thus obtained agitates the material and causes it to be conveyed over the heated surface.

Jan 1, 1938