Search Documents

By J. R. Coleman, G. L. Corrigan

FOUR factors that largely determine the end product obtained when cement and water are mixed are the chemical composi-tion of the cement, the fineness to which the cement is ground, the amount of mixing water used, and the procedure used in mixing the slurry. In order to study the effect of two of these factors, the other two, the chemical composition and method of mixing, are kept constant, leaving as variables fineness and water-cement ratio. Through years of experimentation and usage it has been well established that the reduction of cement clinker to a very fine state by grinding improves its cementing value, principally because the reaction between cement and water takes place only at the surface of the cement particle, further action being hindered by the accumulation of reaction products that tend to coat the unreacted material. Therefore, the moE finety-ground %cement, and the greater the surface exposed in propor-tion to its mass, the more rapid is the The work covered by this paper was done by the authors in pursuance of graduate studies in the ~epartment of petroleum Engineering at The University of Texas. The present paper is a condensation of a more detailed DaDer from which, for brevity, information such as the procedure for determining permeability and some of the discussion and procedure relevant to slurry volumes and fineness of cement have bsen deleted. It was felt that this information would not be of interest to most readers and should be outside the scope of this paper. Manuscript received at the office of the Institute Aug. 16, 1940. Issued as T.P. 1266 in Petroleum Technology. January 1941. hydration rate. Similarly, the greater the surface exposed, the greater the proportion of the cement that reacts, and the lower the amount of residue that is unreacted and so remains inert and unable to make any contribution to cementing properties.] Although it is more expensive to manufacture a finely ground cement than a coarser cement, the advantages of fine grinding of construction cements were so marked that the fineness of cement has increased considerably in past years. When the manufacture of special oil-well cements was begun, it was necessary to consider properties of cement that previously were considered of minor importance, foremost of these being pumpability. Since, with the water-cement ratio constant, a finely ground cement will produce a neat slurry of higher consistency and shorter time of pumpability than will a coarser cement, there is a tendency to grind oil-well cements to a lower degree of fineness. Therefore, in order to produce oil-well cements that will make a slurry having a long time of pumpability, cements are manufactured that because of their coarseness generally are Poorer cementing materials than some of the more finely ground construction and on the other hand, often it is necessary to Pump oil-well cements for long periods of time to place them properly behind a string of casing in a deep well, and since high strength is not of foremost importance for such cement, there is room for considerable controversy concening the proper fineness range.

Jan 1, 1941

By Henry F. Hebley

In preparing this paper it has been the aim of the writer to keep the problems of both producers and consumers in mind. Until now, no attempt has been made to familiarize each group with the other's practice and limitations. This paper is an effort to acquaint the readers with some of the factors pertaining to the problem and cost of mining and preparing steam coal, and also to the economics of producing steam with such coal. In recent years all lines of endeavor have turned to intensive mechanization in order to lower the unit cost of production. The average fuel consumption in steam electric generating stations has dropped in 20 years from 4.0 lb. to 1.4 lb. per kilowatt-hour; while the modern power station can generate 1 kw-hr. on a fraction under 1 lb., or 13,000 B.t.u. coal. Also, the amount produced per man has in that same period risen from 3.8 to 8.2 tons, owing to the use of modernized equipment below ground for coal cutting, drilling, shooting, loading, hauling and hoisting. Unfortunately, the rapid speed of 5 tons per minute of operation at which the coal is loaded mechanically precludes any appreciable removal of impurities at the coal face, so that the raw coal is hoisted containing a markedly higher percentage of impurities than the hand-loaded coal, which was subjected to the scrutiny of the miner during loading. Also, during the past 20 years, certain seams of coal lying close to the surface have been made economically available by the improved design of electrically operated shovels and draglines for the removal of overburden running as high as 56 ft. This strip coal frequently contains so much ash in the raw state (Table 1) that it would have no sales value. Therefore, coal preparation must be adopted to beneficiate the raw product. Some seams in the United States have a decreasing ash content with decreasing size, owing, in all probability, to the fact that the coal is friable while the impurities are hard, causing a concentration of the low-ash material in the fine sizes. Illinois No. 6 coal being rather hard, naturally the reverse is true.

Jan 1, 1938

By W. A. Ver Wiebe

UNder the impetus of new demands caused by the defense program, the oil and gas industries of Kansas established new records during the year 1941. In all, 2113 wells were drilled, which compares favorably with the record total drilled in 1937. These 2113 tests resulted in 1446 oil wells, 76 gas wells and 592 dry holes. In all three categories there was an increase over the previous year, but unfortunately the most marked increase was in the dry holes. Nearly 80 per cent of the increase must be allocated to the drilling 01 unsuccessful tests. This was partly because of the increasing difficulty of finding new reserve areas and partly because of the erratic character of the production in the Arbuckle dolomite, which is now the main producing zone. Closer analysis of the totals reveals that western Kansas accounted for 1634 tests, of which 1186 were oil wells, 34 were gas wells and 415 were dry holes. The total potential initial daily production uncovered by the successful wells amounted to 1,691,000 bbl. of oil and 508,000,000 cu. ft. of gas. Both figures indicate a considerable decrease when compared with the proceeding year; in 1940 the respective figures were 2,128,000 bbl. and 1,289,000,000 cu. feet. In eastern Kansas a total of 479 wells were drilled. Among these, 260 were oil wells accounting for a daily initial potential production of 45,662 bbl. The new gas wells numbered 42 and added 290,438,000 cu. ft. per day to the gas potential production of the state. The remaining tests, 177 in number, were dry. It is interesting and significant that almost half (791) of the total wells drilled in western Kansas were drilled by the independent operators. Among the large companies the Cities Service Oil Co. drilled 169 wells; the Stanolind Oil and Gas CO., 101; the Skelly Oil Co., 80; the Continental Oil Co., 99, and the Shell Petroleum Co., 63 wells. In eastern Kansas the independent operators drilled 406 out of the total of 479 wells. Among the major oil companies the Cities Service Oil Co. drilled 38; the Phillips Petroleum Co., 13, and the Sinclair-Prairie Oil Co., II wells. The figures on relative percentages of dry holes to successful oil or gas wells are revealing. In western Kansas approximately one third of all wells drilled by the independent operators were dry holes. The major oil companies drilled approximately 844 wells in western Kansas, of which 678 were successful in finding either oil or gas. It thus appears that the major companies fared much Getter than the independents. In eastern Kansas the major companies drilled 73 wells of which 63 were successful in finding commercial quantities of oil or gas. No less than 286 wildcat tests were put down in western Kansas and 72 in eastern Kansas, or 358 in all, during 1941. Considerably more than half of these were drilled by independent operators; zoo in western and 66 in eastern Kansas. An exploratory hole % mile or more from production is regarded as a wildcat well in Kansas. On a percentage basis, approximately 75 per cent of all wildcat wells were failures; only 25 per cent found oil or gas in western

Jan 1, 1942

By W. W. Anderson

WEBSTER'S dictionary gives the following definition for "efficiency": "Effective operation as measured by a comparison of actual and possible results." Engineers think of this definition in terms of the ratio of output to input, and since they learn early in their careers that output cannot be greater than input, they usually consider a machine to be 100 pct efficient if it operates perfectly, and to be 0 pct efficient if it performs no function at all. Hence, values of efficiency between 0 and 100 pct reflect how well or how poorly a machine has performed; and any method of calculation for determining efficiency that does not show 0 pct when no function has been performed, and 100 pct when a perfect job has been done, is looked upon with skepticism. The literature on performance of coal cleaning equipment contains many references to efficiency of performance, but there is no unanimous agreement among the authors as to how the efficiency should be determined. Numerous methods of calculation have been proposed from time to time, most of which attempt to fulfill the definition of efficiency by comparing output to input, using float and sink data or some other characteristic, such as dry ash content, as a measure. However, to the best of our knowledge, none of the methods advocated in the past meets the requirements of a practical engineer in judging cleaning plant performance, because the formulas previously advocated do not confine numerical values of efficiency between 0 and 100 pct, and the literature does not contain an explanation of the meaning of the formulas under various conditions of operation. Therefore, the following formula, based on Yancey's concept of misplaced material,' is proposed as a measure of efficiency which will conform with the requirement that the values of efficiency must be confined between 0 and 100 pct: Quantitative Efficiency = 100.0 — (pct wt sink* in cleaned coal + pct wt float* in refuse)t • At gravity of separation effected by cleaning equipment. t Total product basis of the size of material under study. It will be noted from this formula that an actual separation between cleaned coal and refuse must be effected by the cleaning equipment before the formula can be used; also, that improperly distributed material in the products must be determined at the gravity of separation, rather than at some arbitrary test gravity. It will further be noted from this formula that the weight of cleaned coal recovered and the weight of refuse rejected by the equipment have their proper influence, because the sink in the cleaned coal and the float in the refuse are expressed in the equation as a per cent weight of the total products of a definite size discharged from the plant. This formula has one other important characteristic, in that it requires no knowledge of the feed to the cleaning unit. Comparison of data on the products from a cleaning unit with the feed to the unit can lead to many worthwhile conclusions. but not in regard to the efficiency of separation effected by the equipment. The reason for this is that mechanical fracture of many pieces of the feed occurs during the cleaning process; and in some processes crushers are deliberately incorporated in the flow to produce size degradation to free impurities from cleaned coal, thereby altering the washability characteristics of the material while in process. When such size degradation occurs in a cleaning process, it is quite possible that this crushing will result in a reduction in ash content in the finer sizes of cleaned coal when compared with the raw coal feed, even though no true separation has been effected. This is due to the fact that the finer sizes have been "sweetened" by the crushing of cleaned coal from some coarser size. Many formulas advocated in the past show high cleaning efficiencies

Jan 1, 1951

By Kenneth Schellinger

THE terms surface tension and surface energy are well known when applied to liquids and are generally described by referring to the excess energy of the air: liquid interface as a result of unsaturated molecular forces surrounding the surface molecules of the liquid due to the presence of the air phase on one side. Such unbalanced forces produce the familiar water droplet of spherical form and are generally summed up as a surface tension measured in dynes per centimeter which can be shown mathematically to be equal numerically to a corresponding surface energy expressed in ergs per square centimeter. A specific surface energy, however, is best thought of as the energy necessary to produce one unit, of new surface on a substance. Hence, in producing a bubble in a flotation cell the impeller must supply surface energy corresponding to the air: liquid interfacial area on the interior of the bubble. Inasmuch as it is relatively easy to extend or contract the surface of a liquid, there are a number of successful methods for liquid surface tension, or energy, measurement based upon surface deformation. This happy state of affairs does not, however, extend to solids, which are considered to possess surface energies for the same reasons as do liquids, i.e. because of unsaturated ionic bonds at the solid: gas interface. As in the case of the flotation cell producing surface on liquids as new bubbles, it takes energy to produce new surface on solids as new particles. As every mill man knows, this surface is produced on mineral solids in a grinding mill by the action of a tumbling mass of iron balls. But here so much energy usually is wasted by the inefficient action of these balls that a large amount of heat is generated, and the surface energy production may be easily confused with the energy necessary to produce this ineffective heat. The tumbling balls and fracturing minerals ultimately take their energy from a rather large electric motor. It has been variously estimated that from 10 to 20 pct'" only of this energy from the motor does not appear as heat and may be presumed to appear as surface energy on the min- erals present. Such a production of new surface on the mineral phases is accompanied, of course, by a size reduction that is inevitable as more and more mineral interior molecules become surface molecules by the fracture exposure. This size reduction of mineral particles, although the most obvious feature and perhaps the sole object of the milling operation, is from this energy viewpoint the outward manifestation of the production of surface energy only. Measurement of the characteristic surface energies of pure minerals and their various mixtures in ores would be a step towards understanding of the energetics of the commercial grinding operation. In addition, the characteristic surface energy of a mineral is probably a physical property specific for that mineral, and therefore, from a scientific standpoint, should be measured. It is interesting to note that, in contrast to the large body of work on the surface tensions of liquid systems and biological systems, the field of solid surface energies has been neglected. Prior to 1920 it is difficult to find more than one or two references to work on solid surface energies in Chemical Abstracts. Since 1920 such references number somewhat less than 100, while those on liquid systems are numbered in the thousands. Much of this apparent neglect of the field of solid surface energies (the term is intended to be somewhat inclusive at this point and refers both to the solid: gas, and the solid:liquid interface) is because of the lack of a reliable method of measurement rather than any lack of scientific curiosity. It was, and still is, difficult to produce new surface on a solid without the simultaneous production of interior changes in the same solid which may consume part of the energy used. The extension in the surface area can be measured, but the interior crystal-

Jan 1, 1953

By F. R. Zacher

Unmined blocks in the Sewickley seam, surrounded by worked out areas, have been found to transmit overburden oads through the interval strata to the Pittsburgh seam workings 90 ft below. Operating experiences under these conditions are described in this paper. IT has always been understood, in northern West Virginia where both the Pittsburgh and Sewickley seams are mined, that pillaring or splitting in the lower Pittsburgh seam could break the interval strata and make mining in the overlying Sewickley difficult or impossible. In some instances, however, mining methods practiced in the overlying Sewickley have reversed the problem, resulting in a shifting of the intermediate layer and destroying valuable acreages of the Pittsburgh seam below. The Pittsburgh seam in this area is, on the average, 102 in. thick. About 18 in. of low-quality head coal are left for roof protection as it is mined. Immediately over the coal are two draw slates, two rider seams, and a good hard black shale, locally called black rock, which serves as a permanent roof where draw slates and riders are taken down on certain main haulroads. In most areas mined in this seam in the past the bottom has been satisfactory but soft. However, in areas now being mined by the Christopher Coal Co. in Monongalia County the bottom is very hard and unyielding. The Sewickley seam, lying 85 ft above the Pittsburgh, will average nearly 70 in. in thickness and is overlain by massive shales and sandstones. Much of the seam is mined only down to the "sheep skin," a hard band about 4 in. above the bottom, which is composed of relatively hard shale. Fig. 1 shows a typical cross-section through the Pittsburgh and Sewickley seams in the area being discussed. The thin Redstone seam is not deep-mined but is stripped in some locations where it outcrops. Most of the Sewickley seam in the Morgantown areas has been mined out from 10 to 30 years. There are at present only two large mines and five or six others of small production operating in that seam. Mining systems in the past were generally of the room and pillar type with some full pillar extraction. This seam in the Scott's Run area was operated by as many as thirty or forty different companies at one time, during an era beset with strikes, market failures, and depressions. Most of the barrier pillars along the many main haulroads were abandoned, and blocks of Sewickley coal that would be fully recovered with today's machinery were left unmined when conditions became anything less than favorable. Consequently the mined-out Sewickley is spotted throughout with solid blocks varying in size from 100x100 ft to 200x400 ft and larger. It is these unmined Sewickley blocks surrounded by worked-out portions that have caused transmissions of roof stresses to underlying Pittsburgh mining areas, see Fig. 2, resulting in untold difficulty. As the Christopher Coal Co. operates both the Pittsburgh and Sewickley seams, accurate maps of workings in both seams are readily available and are regularly consulted. The first Pittsburgh squeeze attributed to overlying Sewickley blocks occurred in the Arkwright mine, where a shuttle car crew was developing a section consisting of seven panel headings. These entries were being driven in solid coal 3400 ft from the nearest worked-out Pittsburgh area. As mining advanced it was noticed that certain ribs began to slough and certain areas to show signs

Jan 1, 1953

By Myron A. Pugacz, Frank S. McKenna, Clarence E. Jackson

The notched-bar impact test has proved worth while in certain applications as a test for control of the quality or the heat-treatment of steel. In view of the serious thought that even so simple a test as the tensile test has evoked during the past years, it is not surprising that the notched-bar impact test should have inspired much experimental work. The correlation of the great number of data has not been successful, although steady progress has been made toward a better understanding of this test. Progress has been made, especially, in the isolation of the effects of the many variables that control the results. The stress system imposed on a specimen with a notch is so complicated and unpredictable that no simple evaluation of the test has been possible. Because of this uncertainty, many engineers hesitate to use the notched-bar impact test, and this attitude may well continue until a better understanding of the effects of the variables in the test are available. Without doubt, any additional data that may be presented should be accompanied by as complete a description of the - details of test as possible, so that it may be added to the general fund of information that is to serve as the basis for the theory of the notched-bar impact test. The many factors that may control the test results have been pointed out repeatedly. The importance of the effect of the type and dimensions of the specimen has been recognized. Most of the work reported by American investigators has been limited to small-size (Charpy) specimens tested as a simple beam; two types of notches (Fig. I) have been commonly used. Considerable data have also been presented by many investigators using a small specimen tested as a cantilever beam; this commonly being called the Izod test. Here, however, a shear component of stress makes the stress system even more complex than that present in the simple beam type of test, hence a critical analysis is difficult. Much work has also been reported by investigators using the tension type of specimen. A second variable that must be controlled is the testing temperature. An indication that the tests were performed at room temperature is not sufficient, since in many steels a variation of a few degrees in the actual testing temperature may be sufficient to give an entirely different range of results. Other factors, such as the composition and condition of the material being tested and the speed of test, should also be considered. Many investigators have contributed data and theoretical discussions on the problems encountered in notched-bar test-

Jan 1, 1944

By J. Lyden

In the Picher field, structure made openings for the circulation of the mineralizing solutions by flexing, shearing, and fracturing the sedimentary beds. This structure is used with the spatial and genetic relationship of the ore minerals, sphalerite and galena, and the gangue minerals, dolomite and jasperoid, in prospecting for ore bodies. THE Picher Mining Field, fig. 1, which lies between Baxter Springs, Kansas, and Commerce, Okla., is the most intensely mineralized and the largest zinc-lead ore producing area in the Tri-State District of Missouri, Kansas, and Oklahoma. It has a vast lateral extent of underground workings that is unequaled for the observation of the geology of zinc-lead ore bodies in sedimentary horizons; and thousands of churn drill holes in the unmined areas supplement the underground observations with useful data for the interpretation of the geology. This paper is confined to the ore deposits of the Picher mining field. The reader is referred to the bibliography for the general geology of the Tri-State district which has been ably covered by many geologists. The writer was co-author of several publications on the Tri-State district.'-" This paper is necessarily a repetition of parts of those publications but contains a few changes and additions on the deposition of the minerals. The parts of this paper concerning mineralization maps and pipe slump-structures are not covered in the above publications. Geology The geology of the Picher mining field is similar to that of the entire Tri-State district because the sedimentary horizons that are found here are found throughout the district, and the ore bodies in the respective horizons have similar characteristics. The beds that contain the ore bodies in the Picher field are illustrated and described in fig. 2. The five unconformities found in the mines of the Picher field are indicated on the geologic section, fig. 2. The unconformity shown at the base of Meramec (B bed) is relatively unimportant since B bed was mostly eroded from the area of the Picher field before the Chester beds were deposited. B bed has been observed in the cuttings from only a few churn drill holes. The Pennsylvanian (Cherokee shale) formation is the top horizon found in the Picher mining field. It has been eroded from the southeastern part of the field, but because of the regional dip of the sedimentary beds to the west, it attains thicknesses of 100 ft to 200 ft along the west edge of the field. It is 200 ft to 300 ft thick in the Miami trough. It was deposited on the Boone limestone surface, which contained relatively few shallow erosion channels and very few depressions. Subsequent to the deposition of the shale, solution of limestone from underlying limestone horizons by circulating solutions caused the overlying beds, including the Cherokee shale, to slump into the larger openings formed by the solution and removal of the limestone. Chert The origin of the chert in the Tri-State district has been a controversial subject among geologists. Tarr7 advocated a syngenetic origin for the chert, postulating that it formed from colloidal silica deposited in the Mississippian seas. Leith, Dake and Leighton' argued in favor of silicification of erosion

Jan 1, 1951

By Bruce W. Gonser, Robert I. Jaffee

Recent work by the authors1 established the constitutional diagram of the gold-germanium system. Of particular interest in the simple euctectiferous system was the eutectic alloy at 12 per cent Ge, which melted at the very low temperature of 356°C and had an unusually fine eutectic structure. It was of interest to investigate the effect of third components on the melting point, microstructure, and strength of this alloy, and in this work the effect of copper is discussed rather completely, with less complete data on the effects of silver, platinum, nickel, and zinc. No reference in the literature has been found on ternary systems with gold-germanium. Materials and Alloying -4s in the work on the binary system, gold-germanium, the germanium used in this investigation was the cyanide-reduced, 99.9 per cent product, produced by the Eagle-Picher Co. Fine gold sheet from Handy and Harmon, pure platinum sheet from the American Platinum Works, copper magnet wire from Anaconda, nickel wire assaying 99.6 per cent Ni. and electrolytic zinc were used for alloying. To make the alloys, charges of the pure metals were put in a graphite crucible and melted in an atmosphere of pure hydrogen. The temperature was brought up to about I050 C, and the metal allowed to freeze in the crucible. Except with alloys containing zinc, melting losses were consistently less than a few milligrams. When zinc was a component, weight losses up to half the weight of the zinc present were incurred, and the alloy compositions were calculated by assuming the entire weight loss to be that of zinc. In all other cases the composition of the alloys could safely be taken as that of the charge. The ingots, as solidified, were segregated, the heavier primary phases being at the bottom and sides of the ingots and the lighter primary phases at the top, but by sectioning the entire ingot vertically for microscopic examination, this factor could be evaluated. Ingots for microscopic examination weighed one gram, and those for thermal analysis weighed three grams. Thermal Analysis In this work, the eutectic line composition and thermal arrests were desired, and, after microscopic exploration had established the position of the eutectic line at a given percentage of the third component, a thermal analysis was run at that composition. The method of thermal analysis used in the work on the binary Au-Ge system,' a method particularly well suited for a small quantity of material, was used in this work. Clearly defined arrests were obtained, although with some alloys containing platinum

Jan 1, 1946

By I. W. Walling, F. B. Plummer

Bastin and others have demonstrated the presence of sulphate-reducing bacteria in oil wells producing salt water. Analyses show that at 125°F. bacteria alone reduce sulphates in East Texas salt water by only 3 per cent in 30 days, forming principally hydrogen sulphide and sodium or calcium hydroxide. The hydrogen sulphide reacts with soluble iron compounds to produce iron sulphide in the absence of oxygen, and ferric hydroxide where oxygen and air are present. Where iron or other metals and iron sulphide are already in the water containing bacteria, I00 per cent reduction of the sulphates is complete in 30 days or less; where magnesium is present, reduction is complete in 15 days. The effects of changes in temperature, of different bactericides, and of concentration of bactericides on sulphate reduction are described in detail and illustrated by tables and curves. The significance of sulphate reduction on corrosive properties of oil-field water is briefly discussed. Chemistry of East Texas Oil-field Water The chemical composition of the water in the East Texas field salt-water disposal pits is shown in Table I. This salt water corrodes pipes, pumps, and steel tanks excessively, principally because of its content of oxygen, hydrogen, sulphide, and carbonic acid. The carbonates in the water when exposed to air tend to give up carbon dioxide and to precipitate calcium carbonate in large quantities. This forms coatings in tanks, settling pits, and ditches, and soon, unless removed by acid treatment, will effectively clog an injection well and reduce the flow of water back into the ground. The iron compounds in the water, most of which are dissolved from tanks and pipes, are in the ferrous form, and when exposed to the air are oxidized from soluble ferrous carbonate to insoluble ferric hydroxide, resulting in the precipitation of a gelatinous precipitate that will clog oil-field sands effectively: 2Fe(HCO3)2 + O + H2O -> 2Fe(OH)3 + 4CO2 The sulphates in strong sulphate-bearing water may be attacked by swarms of sulphate-reducing bacteria and more hydrogen sulphide may be produced. The hydrogen sulphide reacts with soluble minerals in the water to form black sludges. A knowledge of the chemistry of each reaction in oil-field water is important to the oil-field engineer, since means must be devised to prevent the formation of harmful precipitates that clog injection wells and to prevent corrosion of tanks by harmful products of biochemical processes. Methods of Treating Water before Injection into Ground* The open system of handling the waste salt water in the East Texas field consists of aerating and chemically treating the water to precipitate the unstable iron,

Jan 1, 1946

By T. Egleston

THE ores of mercury of North California are composed of metallic mercury and cinnabar. They are found in serpentine, and are very often associated with chalcedony, in masses more or less irregular, often concentrated enough, however, to furnish ores yielding from three to ten per cent., and sometimes richer. This deposit makes its appearance in Vallejo where it has been worked. North of here the mines are more developed. Most of the quicksilver mines, how¬ever, are situated in Sonoma and Napa Counties. On its outcrop the serpentine rocks have become decomposed, and have often been washed away to a considerable depth, so that in many cases in their neighborhood, what is apparently nothing but ordinary dirt, will frequently contain from two to three per cent. of metallic mercury, with but a trace of cinnabar, in which case, as at the Sonoma mine, it is made up into adobes and distilled. Such material does not require to be mixed with dirt to be made into adobes. Very often, also, the outcrop of the rock, where it is not decomposed, is filled with metallic mercury, so that by striking a pick into it, as at the Rattle-snake mine, a pound or more of mercury at a time will sometimes spurt out. Such rock as this is found in several localities in every stage of impregnation, and usually makes very rich ore. There is generally, however, very little of it, and it is found only in the first workings ; the ore in depth is always cinnabar. At the Rattlesnake mine near Pine Flat, where large quantities of metallic mercury are found, the rock contains so much petroleum that it has been necessary to make special arrangements to burn the carbides of hydrogen, since the distillation of the petroleum causes an extra quantity of poor soot to be formed in the condensation-chambers. At the Geysers the ore is associated with large quantities of sulphur and gypsum, so that in a hand specimen there is often more sulphur than cinnabar, which is a serious impediment to working, especially for the modern style of furnace with iron condensers, and causes so much soot to be formed that it has been known to penetrate as far as the blower, and to so completely clog it as to prevent its revolution. The ore coming from the mine is more or less hand-picked. In one or two cases attempts have been made to treat the poorest, and especially the very fine ores, mechanically as at the California works.

Jan 1, 1875

By C. E. Sims

The carbon-oxygen reaction without doubt is the basic reaction in steelmaking. It is important on several counts: In the first place, carbon is the element that distinguishes steel from iron. It is the principal element controlling properties, and its control is of prime concern. Although the principal objective of the carbon-oxygen reaction is to oxidize excess carbon, the accompanying boil should not be underrated. The mechanical agitation, stirring, and mixing resulting from the boil are so useful in the distribution of heat and in promoting uniformity of composition in the bath that, were it not a natural accompaniment of the carbon-oxygen reaction, it is probable that something would have to be invented to replace it. The open-hearth operation, for example, with the bath heated from above by radiation, would be impracticable without the carbon boil. The electric-arc furnace is somewhat less dependent on it, but every melter knows how much easier it is to gain temperature with minimum damage to refractories during the boil than with a dead bath The motor action of the induced current of the induction furnace makes the carbon boil unnecessary but even there a severe oxidation has been found useful in giving greater freedom from porosity in certain steels. The quantitative aspects of the carbon-oxygen reaction have been given considerable attention by a large number of investigators, and the principles of physical chemistry have played an important part in these studies. Physical chemistry is the science of the mechanics and mathematics of chemical reactions. It is possible to study the mechanisms of reactions in a qualitative manner writhout reference to mathematics and thus obtain valuable concepts as to the manner in which the wheels go around. When it is desired to express quantitative relations in these reactions, however, resort to mathematics is not only convenient but necessary. Mathematics may also be regarded as the shorthand language of physical chemistry. A basic relation whose description requires numerous words may be expressed very simply by a mathematical formula or equation. A good example of this is the equilibrium constant for a chemical reaction. Expressed verbally, it is: When a chemical reaction has reached a condition of equilibrium, the Product of the concentration of the reacting substances on one side of the equation, divided by the product of the concentration of the reacting substances on the other side, gives a quotient that is a constant at constant temperature For the carbon-oxygen reaction C + O ^ CO this is expressed simply as % C X % O -%co where K (from the German Konstant) is the equilibrium constant for the reaction. Although mathematics is such a necessary and useful tool, it is also a potential pitfall. Mathematics in itself is an abstract science, which is not inhibited by consideration of mechanisms or materials.

Jan 1, 1948

By H. C. Burghard, F. R. Brotzen

Experiments were performed to determine the effects of mechanical vibrations on ordering in CuAu. The effects of 5, 10, and 15 kc vibrations were investigated over a range of ordering temperatures of 280° to 360°C. A decrease in the rate of ordering was observed at all frequencies and ordering temperatures. THE effects of mechanical vibrations on certain solid-state reactions have been noted by several investigators. In 1930, Mahoux' reported a substantial increase in the case depth of a steel sample nitrided under the influence of mechanical vibrations over that of an unvibrated sample. Similarly, an accelerating effect of vibrations on the diffusion of chromium in steel was noted. Guillet, in the same year, confirmed the results of Mahoux. More recently Schenck and schmidtmann3 studied the effects of low-frequency, alternating loads on the diffusion of carbon in steel. The results of their experiments, conducted at 500 cycles per min and large strain, (0.2 pct), indicated an acceleration of the process. These workers also reported an increase in case depth of a sample vibrated at 430 kc during a carburizing treatment. Effects of high-frequency vibrations on solid-state reactions have also been investigated by Gudzoff and Gavze6 and Fairbanks and Dewez.7 The former reported an acceleration of the age-hardening process in aluminum alloys. The latter noted changes in the structure and mechanical properties of steel annealed under the influence of vibrations. On the other hand, Altenburg4 and Ehringer5 have given some theoretical reasons and experimental evidence as to the improbability of any effect of vibrations on diffusion. Comprehensive surveys of the effects of vibrations on metallurgical reactions are given by Hiedemann' and Bergmann.9 None of the above investigations led to a physical description of the effects of mechanical vibrations on solid-state reactions. In the present study an attempt was made to gain an understanding of the influence of vibrations on nucleation and diffusion. The order-disorder transformation was chosen for investigation since its mechanism has been extensively discussed in the literature. Moreover, the progress of the transformation may be easily followed by observation of electrical resistance changes. EXPERIMENTAL PROCEDURE The specimens used for the experimental observation of ordering rates were prepared from 50 at. pct Cu-Au alloy wire.* Each specimen consisted of a 0.02-in. diam wire approximately 10 in. long to which two copper potential leads were silver soldered, 2 1/2 in. apart, near one end of the wire. A 1/8-in. diam by 1/4-in. long steel stub was silver soldered

Jan 1, 1960

By N. K. Chen, R. Maddin

THE textures of straight-rolled and of cross-rolled molybdenum were first determined with the aid of pole figures by Custers and Riemersma.' These authors have shown that for straight-rolling, the main texture was (100) [0111 with a considerable spread about the rolling direction. After cross-rolling a second texture was obtained in which there was a [111] axis perpendicular to the rolling plane, possessing a rotary symmetry. Recently Semchy-shen and Timmons2 in their study of preferred orientation of arc-cast molybdenum sheet obtained similar pole figures. In these two investigations, polycrystalline materials were used. In the main, the textures of molybdenum in these cases are qualitatively consistent with rolling textures of other body-centered cubic metals, such as iron and Fe-Si alloys." In the present investigation, single crystals of molybdenum were deformed by rolling with respect to specific crystallographic planes and directions. Since the deformation textures of polycrystalline aggregates have been related intimately to the behavior of individual grains,4 a study of possible correlations of final textures with respect to the initial orientations of the single crystals might conceivably lead to a better understanding of the textures. Annealing treatments were carried out after deformation in order to study the recrystallization characteristics as well as the recrystallization texture. Rolling of Single Crystals Single crystals of molybdenum (about 1/8 in. in diarn x 1-in. long), grown by the method previously described,5 were cold-rolled without intermediate anneals. Except for specimens MR-1 and MR-2, which were rolled at random in the preliminary test in order to find a proper rate of reduction, all other specimens were carefully documented as to their respective orientation before deformation by means of X-ray Laue back-reflection methods. A stereo-graphic projection was constructed from which it was possible to determine a particular plane and direction to be considered for rolling. Parallel flat surfaces were then polished metallographically with respect to a reference scratch on the specimen which was mounted in sealing wax. These flat surfaces contained the plane chosen for rolling. After etching, a Laue back-reflection photogram was again made of one of the flat surfaces to determine the exact plane of rolling. The initial orientations of all the specimens (specified by two elements for each crystal, direction of rolling and the pole of the rolling plane) are summarized in Fig. 1. The specimens were mounted in plasticene between two hardened Si-Fe plates. The sandwich was then rolled down, keeping the direction constant in the case of straight-rolling. In cross-rolling (MR-10, MR-11, and MR-12) the sandwich was rotated 90" after each pass so that every first and third pass contained the same rolling direction. Specimens MR-14, MR-15, and MR-16 were compression-rolled following the manner of Barrett." In these cases the direction of the sandwich through the rolls was changed by 3" to 5" for each pass until the specimens were rolled to the desired reduction in thickness. It was found that if extreme care was exercised in rolling, i. e., the amount of deformation per pass was extremely small, the specimens could be rolled to a large reduction in thickness. The rate of reduction used, with a single exception of MR-1. was generally 0.001 in. per 10 passes. Thus, it took about 800 passes to reduce a specimen to a final reduction in thickness of 87 to 98 pct. The results of rolling are shown in Table I. Cold-Rolling Textures The final orientations were determined by the conventional Laue transmission method," using molybdenum radiation, with or without a zirconium filter. Pole figures were plotted from (1101 and (200) reflections in which three degrees of intensity— heavy, medium, and light—were determined visually. Three main types of textures have been observed from the deformed single crystals. These are: 1—a

Jan 1, 1954

By L. L. Gray, D. W. Reed, F. Morgan

A flowMeter has been developed at Gulf Research and Development Co. and tested in the field for measuring the flow of gas in well bores. It has been used in a study of the injection capacity of different horizons in gas injection wells in Oklahoma. The flow sensitive element of the meter is a semi-conductor having a very high temperature coefficient of resistance. Advantages possessed by this meter are the result of that property and the high specific resistance of the element. The instrument possesses a sensitivity considerably higher than any reported previously. In the application described here the element is heated to a temperature considerably above ambient by an electric current, which is supplied by a voltage source at the surface. When fluid flows through the meter the rate of dissipation of heat is increased and the temperature of the element decreases. Because of the negative temperature characteristics of the resistance element such a decrease of temperature will be accompanied by an increase of resistance which, under flow conditions ordinarily found in wells, is of such a magnitude that it can be directly measured or recorded in terms of a change in voltage at the surface. In practice, rate of flow is measured in terms of the drop in voltage in the resistance element. All the metering and control apparatus remains at the surface while the thermal element is lowered into the well on a single conductor cable, consisting of an insulated wire and sheath. The meter is calibrated by passing known quantities of gas through it either at the surface or in the hole at a point immediately above the region in which gas is lost to the formation. In case calibration is made at the surface, the ambient temperature in the hole may readily be obtained by a second resistance element which is operated at a current so low that effectively no heating occurs. The instrument has been adapted to con-tinuous recording, but the velocity of the meter relative to that of the gas must be low unless corrections are made. Curves giving data obtained in actual field tests are shown' The meter can also be used to determine the distribution of flow capacity in a gas producing well. A differential form of the meter has been designed and built in which the local flow or injection capacity of the formation is obtained directly. Introduction When fluid is injected into a well in a secondary recovery or pressure-maintenance operation the question of its most effective use invariably arises. Although the core log, when available, will show the regions of good permeability and oil saturation, there is normally no assurance that the fluid actually enters the formation in zones where injection is deemed desirable. In view of the uncertainties involved in such programs, it is generally conceded that measurements of permeability for a formation in place are more significant than those obtained by the core-sampling technique. A subsurface meter has been developed at the Gulf Research and Development Co. for measuring flow of fluids at different horizons in a well bore, and field tests have been made on the instrument in Cooperation with the Tulsa Division of the Gulf Oil Corp. In this paper the meter is de-

Jan 1, 1948

By R. E. Anderson, R. S. Busk

The mechanical properties of many nonferrous alloys can be modified by heat-treatment. This is almost always effected by controlling the amount of alloy in solid solution and the amount and distribution of second-phase material. The latter often is accomplished through precipitation or age-hardening treatments. The procedure is to solution-heat-treat the metal to provide a supersaturated solid solution and then cause precipitation of the dissolved material at some temperature below the solvus for the alloy. The generally used magnesium sand-casting alloys arc based on the ternary alloy system Mg-Al-Zn. Solid diffusion reactions in the system are slow enough so that a substantially completely supersaturated solulion is maintained even though the metal is relatively slowly cooled from heat-treating temperatures. Consequently, it is general practice to air-cool magnesium-alloy castings from the heat-treatment temperature prior to aging at an elevated temperature. Since it is necessary with many other alloys to cool quite rapidly before aging if optimum benefit from the aging is to be obtained, this study was undertaken to determine the effects of quenching on magnesium alloys. The] alloys used are shown in Table I, being selected as typical of the presently used magnesium alloys. Cooling Rates Since quenching is a means of rapidly extracting heat, there are two factors of interest in its study: (I) the rates of cooling that can be obtained and (2) the effect of various rates on the as-cooled as well as subsequently aged metal. The cooling rates were measured by drilling a hole 1/16- in diameter longitudi~lally in the center of a cylinder % in. in diameter and 3 in. long. The drilling was stopped to place the end of the hole at the center of the long axis of the cylinder. An iron-constantan thermocouple was inserted in this hole and wedged in place. The temperature drop during rapid quenching was recorded by a special1y built General Electric potentiometer recorder capab1e of measuring ' 500°F. temperature drop in 1/10 sec. For the slower cooling rates in air or oil, the temperature drop was measured by a Leeds and Northrup potentiometer recorder with the chart speed increased to One inch per minute' The cylinder was heated to the desired temperature, quenched as desired, and the temperature-time curve recorded. The cooling rates in still air, in oil at 350°F., in water at 180°F. and in a cold, high-pressure water spray were determined in this manner. The results of this study are presented in Fig. I. There is a great difference between water quenching and either air or oil quenching. There is little difference between the hot water quench and the cold water spray. Cooling rates were also

Jan 1, 1945

By W. Crafts, J. L. Lamont

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,' as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By John L. Ham, Robert M. Parke

THE melting point of molybdenum is 2625° ± 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. 1, 1944, to Aug. 31, 1945, the project was under the supervision of the National Defense Research Committee, Division One. In peacetime, too, there are needs for molybdenum, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. FIRST PROCESS FOR MELTING AND CASTING MOLYBDENUM The maintenance of a temperature greater than 2625°C. in a space large enough to melt several pounds of molybdenum may involve the loss of heat at a very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum. In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1946

By J. C. Deppe

A method is presented for calculating approximate injection rates in secondary recovery operations. The method can be applied to cases of unequal fluid mobilities, irregular well patterns and boundary patterns. The steady-state pressure distributions for the four flood patterns reported by Muskat and for five additional patterns reveal that most of the difference in pressure between the injection and producing wells occurs in regions around the wells which can adequately be described as regions of radial flow. This leads to a method of calculating injectivity by approximating the flood pattern with radial flow elements (or a combination of radial- and linear-flow elements for some patterns such as the direct line drive). Irregular and boundary patterns can also be approximated by radial and linear elements. Each of these elements can be described by radial-and linear-flow equations and the results combined as series flow resistances to give an approximate equation for the initial injection rate. The mobility ratio does not affect the initial rate; therefore, if the well pattern is one of those regular patterns for which theoretical rate equations have been derived for unity mobility ratio, the approximate initial rate equation can be improved by adjusting it to match the theoretical equation. The available theoretical rate equations are listed, including five new cases. As the flood progresses, the injectivity changes because in general the flood front will divide the pattern into areas of different fluid mobilities. Simple shapes can be assumed for the flood front so that both areas can be divided into radial- and linear-flow elements. Radial- and linear-flow equations are applied to these elements to account for the change in flow resistance behind the front. To calculate injection rates after breakthrough, it is necessary to know the sweep efficiency at breakthrough. Areal sweep data are available in the literature for a number of patterns, and sufficiently accurate breakthrough sweep efficiency can be estimated from these data if it is not otherwise available. Again, simple shapes for the flood front can be assumed after breakthrough, and injection rates can be calculated for the remainder of the flood. When areal sweep data are available, these data can be used to cbeck. the calculated injection rates after breakthrough. Injection rates calculated by this approximate method compare favorably with available model data. INTRODUCTION When the fluid mobilities in the swept and un swept regions are equal, the injectivity will not change as the flood front advances; and for regular patterns it can be calculated by mathematical formu1as.l When the fluid mobilities in the swept and unswept regions are not equal, the injectivity will increase or decrease as the flood front advances. In this case, the injectivity has not been calculated by analytical means for any practical well pattern; and, furthermore, scale model and analog4,6 results have been published only for the five-spot pattern. The main object of this paper is to present an approximace method for calculating injectivity for the case of unequal mobilities. The method can be applied to regular, irregular and boundary patterns. Before the approximate method is discussed, the analytical formulas for equal mobilities will be summarized, and the analytical solution for radial flow with unequal mobilities will be used to show how the injectivity changes as the flood progresses. EQUAL MOBILITIES, REGULAR PATTERNS In a flooding operation the injectivity, the rate at which fluid can be injected per unit difference in pressure between injection and producing wells, depends on basic physical properties and, in addition, on three variables to be treated here—the area of the swept region, the fluid mobilities in the swept and unswept regions, and the well geometry (pattern,

By Carl A. Zapffe, M. Eleanor Haslem

The present investigation has three principal purposes: 1. To develop a method for measuring hydrogen embrittlement that avoids cer, tain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. Selecting a Test Method Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. Developing a Machine for Measuring Hydrogen Embrittlement As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1947