Search Documents

By W Mez

The German mining industry uses different residues for backfilling and stowing. A hydraulic pipe conveying technology for these materials has shown advantages for the transportation into the mine. Pipeline conveying systems are able to bridge long distances, they save room within the underground workings and they save staff and costs. Absolutely necessary for successful use of the hydraulic conveying technology is the knowledge about the unusual non-Newtonian flow properties of solid/liquid mixtures like pastes and slurries. The flow resistance of these materials cannot be described easily by one viscosity. Owing to a yield point and a pseudo-plastic behaviour the viscosity changes with the shear rate and with the streaming velocity inside the pipe. Also these flow behaviours depend very sensitively on the liquid/solid-ratio, often so dramatically that gravimetric or volumetric dosing equipment is not in a position to control the production of backfill pastes. Quality changes of the solid raw materials (particle size distribution, density, mineralogical composition) lead to additional difficulties. The first experiences with hydraulic backfilling plants were troubled by plugged pipes, a bad backfill quality caused by unnecessarily high water content and high costs for chemical binders to solidify the backfill. The installation of viscosity controlled paste production leads to success with the hydraulic backfill technology. A development of the DMT, a bypass pipe-viscometer, has been the key technology. The system is able to analyse on-line, difficult, sticky and abrasive substances and determine their non-Newtonian flow properties. Because the system measures real physical values it is in a position to pre-calculate process relevant parameters like the pressure drop of the backfilling paste in the conveying pipeline. Newer types of the viscometer system also measure the slurry density and calculate its composition. These systems have proven a success controlling backfill paste production plants. They offer a secure prevention of pipeline plugging and a production of high quality backfill pastes with a water content as low as possible.

Jan 1, 1998

By Hussey K. J, Morrison R. S

Recent mapping (1989-1992) by the Northern Territory Geological Survey in the Tennant Creek 1:250 000 map sheet area has resulted in substantial revision of the lithostratigraphy of the Tennant Creek Block (Donnellan, Hussey, and Morrison, in press). Briefly, the former Warramunga Group (Dunnet and Harding, 1967; Dodson and Gardener, 1978) is divided into the Warramunga Formation, and an overlying less deformed volcano-sedimentary succession, the Flynn Subgroup. The latter is conformably overlain by the Tomkinson Creek Subgroup of the Tomkinson Creek province in the north of the Tennant Creek Inlier. These two Subgroups constitute the Churchills Head Group which is essentially equivalent to the Hatches Creek Group of the Davenport province to the south of the Inlier.

Jan 1, 1994

During 1991 - 1993 the author interviewed approximately thirty senior managers of varying responsibilities in either the engineering, construction or operation of a heavy industrial facility. The purpose of the exercise was to determine the factors driving a deterioration of the working relationship between the engineering and the operating company following practical completion of a major project. From the research a number of conclusions have been drawn as to the root cause of the deteriorating relationship. For this paper we are drawing on this initial research and our ongoing experience of solving problems of this nature to present some fundamentals that can be used to break the breakdown maintenance cycle.

Jan 1, 1998

By Clark G

The latest addition to the grinding circuit at Bougainville Copper Limited is another 5.5m by 7.3m primary mill (No.13). The mill can operate in a primary or secondary mode. Its distinguishing feature is its capability for speed variation, by means of a cycloconverter-fed synchronous ring motor. The engineering and metallurgical reasons for selecting such a drive system are described together with aspects of the installation and commissioning. Results of investigations into the relationship between mill speed and grinding efficiency are presented. It is concluded that mill speed variation within the range 70 to 80% of critical speed has very little effect on grinding performance. Beyond this range, grinding performance deteriorates. The same conclusions were reached when mill speed was varied at reduced ball charge levels.

Jan 1, 1986

By Kinsella B

Titrimetric studies have been carried out on the activated carbons Kintal 1105, Norit 2520 and Kuraray 2GA. Titration curves of the carbons before and after acid and water washing and gold loading indicate that the acid-base properties of the carbons are affected by both the method of treatment and also by the loading of gold. It is considered that the pKa values of the functional groups on the carbon surface are in the regions of 11, 7 and 3 respectively.

Jan 1, 1984

The introduction of on-stream analysis in flotation circuits has raised the possibility of automatic control of flotation performance by digital computers. The development of control strategies for an industrial zinc cir- cuit is discussed with reference to identifi- cation of the major disturbances, investigation into the performance of the circuit, the design of the control algorithms, the testing of their performance and their implementation in a production environment.

Jan 1, 1983

The Beaconsfield gold mine processing plant is a complex operation and utilises crushing, grinding, gravity gold concentration, sulfide flotation, bacterial oxidation, cyanidation and zinc cementation to recover gold from the partially refractory ore. This paper discusses the challenges, developments and advancements throughout the processing plant since start up, which have culminated in a 25 per cent increase in the mill throughput over the nameplate design and a concomitant gold recovery increase from 75 to 92 per cent. The improvements have been attained via advancements in mechanical integrity, metallurgical review, process control and operator training, resulting in the current operation producing over 630 000 ounces of gold to date.

Jan 1, 2007

Interest in the sampling of refined copper cathodes has heightened over the last ten years. This has followed the increasing importance of cathodes as the principle trading form for metallic copper. It has also been given impetus by recent trends for quality certification of manufacturing inputs, specifically the AS3900 and IS09000 series of standards.

Jan 1, 1976

By Williams J. D

Magnetite has been used in coal processing for many years and it is likely that its use will continue well into the twenty first Century. While magnetite is only a minor cost component in coal processing, the use of processed magnetite in dense medium separation is essential to provide the split of quality coal products which the markets of today demand. The occurrence of magnetite in Australia is relatively abundant, but a combination of its iron content, magnetic properties, quality and proximity to the coal processing plants is essential to provide a low cost product for use in the Coal Industry. The demand for more splitting of coal in coal processing may require more grades of magnetite, particularly as a finer grade lower specific gravity medium to separate the finer quality low ash coals.

Jan 1, 1991

By Firkin GR, Allen RJ

Sulphide Corporation Pty. Limited has roasted a number of different zinc sulphide concentrates on its sinter machine which pro- duces zinc-lead sinter for an Imperial Smelting Furnace, and results have varied widely. The differences are considered to be functions of !concentrate particle size and reactivity. Amdel have used differential thermal analysis to examine these concentrates and two major effects have been found. Firstly, in concentrates 1containing small quantities of pyrite and chal- L [copyrite, heat is liberated at 400¦C to 650¦C [by oxidation of these two sulphides. Secondly, as particle size decreases, heat release from the oxidation of zinc sulphide commences at flower temperatures and rate of heat release In a sinter bed, the presence of some rite and chalcopyrite would help to heat the cc sulphide to ignition temperature in a orter time, while a finer concentrate would sult in roasting being completed more ickly. Both of these effects result in a arper flame front and minimise the chance heat and combustion fronts being mismatched. is theory is supported by sintering results tained by Sulphide Corporation. As a result

Jan 1, 1975

By Chugh Y. P

A simplified, three-dimensional, time-dependent, mechanistic model of the overburden-coal seam-floor interaction has been developed and validated at two Illinois coal mines. The model based on the thin plate theory can involve any complex layout of mine workings, time-dependent sequence of extraction and, rheological properties of immediate floor strata. The model output data consist of spatially distributed surface subsidence and its slope and curvature, as well as load acting on pillars in one or more panels. A comparison of calculated and monitored surface subsidence or in- mine convergence measurements has proven the model's effectiveness for surface subsidence and load transfer Prediction.

Jan 1, 1992

By Moore A. J

Control of blast vibration requires that its nature and causes be understood, and that effective control procedures be implemented to ensure compliance with limits related to the probability of damage to buildings/structures and human discomfort. This paper covers measurement equipment, assessment and prediction techniques, blast vibration control procedures and applicable statutory limits. It reviews current practice, and provides information on recent developments in blast vibration measurement equipment and control techniques, using examples based on Hunter Valley mining practice.

Jan 1, 1995

By Lu S, Zhou S

The flash smelting technology employed in Jinchuan demands a better mineral processing concentrate with an MgO content below 6.5 per cent. Two ways for MgO removal have been investigated in detail based on properties and process mineralogical characteristics of the rich ores in the number one mining area in Jinchuan. The key to the first way is the use of a new flowsheet which has two-stage grinding and separation followed by single-stage regrinding and multi-stage cleaning for the rougher concentrate. The second approach utilises two novel reagents, AT-131 and AT-202, which have been developed recently. Excellent metallurgical performance has been obtained in a commercial test and a batch test, respectively. The MgO content of flotation concentrate can be reduced to about six per cent.

Jan 1, 1996

By Childs G, Ritchie IC

This paper describes the principle and operation of small hydrocyclones for use in the coal, minerals and other process industries. The principles for selecting a hydrocyclone for an application are also discussed. Typic- al uses and installations in various industries are described.

Jan 1, 1984

By H Rouhullahi, E B. Veshki an, R Kottnauer

The Galandrud coalfield is located approximately 20 km south from the coast of the Caspian Sea, Ruyan town, on the north slopes of the Alborz mountain range, in the elevation between 500 m (the Galand River valley) and 1350 m. For the time being, 32 coal seams (generally of small thickness û 0.8 m on average) have been recognised within the. On the other hand 72 coal banks of balanced properties have been included in reserve calculation, which means that some of the seams consist of several banks. The general dip of strata belonging to the south limb is about 30¦ to the South (with drags close to the south overthrust, where the dip reaches 85¦), while the dip of beds at the north limb is rather steep and usually between 45 to 75¦ to the North. The coal quality is in a rank of high volatile bituminous coal. The steep dip, unstable lithological development, complicated tectonics and comparatively lower coal seam thickness are the characteristic features of the Galandrud deposit. Environmental protection of this area makes exploration and exploitation more complicated. During mine exploration several adits were driven at three levels with 50 m vertical distances. About 4000 m of gates and crosscuts were up to now driven. During mining test the down-cut mining method (with one cut), the strike cut mining method and the down-cut mining method with two cuts were tested. The paper describes outlines for the selection of mining methods on the base of classification of the effective hangingwalls and footwalls, hazards of mining operations, and possibilities of the mechanised mining.

Jan 1, 2003

By Phipps P. J

The rate of precipitation of ferric iron as ammonium jarosite, NH4.Fe3(SO4)2(0H)6 from acidic solutions near 100¦C, was found to increase with weight of jarosite seed crystals, and with concentration of ammonium ion, but to decrease with increasing acidity. The particle size of the product crystals was larger at low sulphate concentrations and at high ammonium concentrations. Particles appeared to be agglomerates, with diameters ranging from 0.5 up to 25 um, and composed of individual crystals of diameters ranging from 2 um apparently down to 0.1 um or Lass

Jan 1, 1977

An improved method of sample recovery for use with rotary percussion drilling has been developed. Cuttings can be recovered continuously from either dry or wet drilling, and the recovery under dry conditions is seldom below 99% of the cuttings brought to the surface by the rig. The system is designed for use with top drive drilling rigs using flush-jointed drill rods. The key feature of the system is a self-aligning mechanical seal around the drill rods. The sealing unit is removably fixed to a collar section of cas ing. the cuttings are recovered in a plastic bag attached to the bottom outlet of a cyclone. A valve at the bottom of the cyclone permits the cuttings representing various depths to I,e recovered separately for examination eind 0(iclysis. [u the Iron Monarch quarry, two percussion holes were drilled to depths if 30 metres and 28 metres using the unproved sample recovery system, and diamond drill holes bored 1 metre from each percussion hole. Samples from each hole were sectionalized over metre intervals and analysed for iron, silica, alumina and loss on

Jan 1, 1976

By Yusuf R

Many heap and dump leaching processes involve competitive, complementary and sequential reactions between multiple minerals and reagents. A comprehensive model has been developed to deal with these complex chemical interactions which is based on diffusion control of the reaction rates. All of the mineralogical and chemical data are obtained from representative samples of the ore or the chemical literature. These properties have been incorporated in a general way, making the model applicable to a range of ore-process systems. The simulation is used to predict the absolute reaction rates and can be used before any leach tests are carried out on the ore itself. The applicability of the model and some tests of its validity are presented.

Jan 1, 1984

By Barns K. E, Munro P. D, Brindley S. K

Ernest Henry Mining Pty Ltd started production in August 1997. The Ernest Henry orebody consists of two distinct parts, a complex supergene ore zone overlying a primary ore zone. The economic copper minerals in the supergene ore are chalcocite

Jan 1, 1998

By Still RF

Sintering of lead and zinc concentrates is practised by Sulphide Corporation Pty. Limited to provide both desuiphurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulphur dioxide gas for sulphuric acid manufacture. From November, 1969 a 20 percent increase in production rate has been obtained through improvements in operating technique. A gradual increase in bed permeability was achieved by modifications to the feed mix conditioning equipment and by improving moisture control. However advantage could not be taken of the higher permeability to increase sulphur elimination because the hardness of the lump sinter decreased. Higher throughput, better quality sinter and more stable sintering conditions were however made possible by simultaneously: 1. reducing segregation and compaction in the sinter bed, by narrowing the discharge opening of the main layer feed hopper, 2. reducing the sizing of sinter returns to give a closer size spectrum of particles in the feed mix, and 3. increasing the sulphide sulphur content of the feed mix to give higher bed Temperatures.

Jan 1, 1972