Search Documents

Mining is taking place at increasing depths of cover on the Southern Coalfield beneath pre- dominantly massive sandstone strata. Within the next twenty years, there will be longwall mining at depths greater than 600 m. As the Sydney Metropolitan area continues to expand and as coal mining approaches these urban areas subsidence will continue to become an increas- ingly important aspect of coal mining research. Investigations commenced in the mid 1960's and it is now possible to predict subsidence in the Southern Coalfield with reasonable con- fidence. The work is showing that the characteristics of the subsidence troughs over the deeper mining at Appin differ from the characteristics of mine subsidence at less cover. The longwall mining at Appin Colliery has resulted in a maximum measured subsidence of 730 mm. The maximum strains were small because of the large radii of curvature of the subsidence profiles. There was no damage to any of the buildings in the township of Appin.

Jan 1, 1981

By Brown GA

Results are presented which demonstrate the feasibility of employing electrolytic membrane technology to process leach liquors derived from alkaline pressure leaching of scheelite concentrates and to recover and recyle sodium carbonate. Thus the problem of disposal of sodium sulphate is avoided. In a further application of the technique sodium tungstate is converted to tungstic acid which can be further processed by three possible routes to crystalline or amorphous tungstic acid or tungsten powder. In each route sodium hydroxide is produced which on carbonation can be recycled as soda ash to the pressure leach stage. Further testwork is required to determine long term operational conditions in the membrane cell and to confirm the effect and deportment of impurities on products. The process has been patented.

Jan 1, 1986

Gold mineralisation at the Macraes Gold Project is hosted in the Hyde-Macraes shear zone and can be traced for ~30km along strike, although economic resources are confined to a 7 km section in the vicinity of the Macraes township. The shear zone, which typically dips at a low angle (~20 o ) to the NE, is bounded by an upper hanging wall shear and a lower footwall fault. Mineralisation occurs along the hangingwall of the shear zone as well as in low angle concordant shears and stockworks. Ore types include graphitic cataclasites with variable amounts of quartz veining, ælode schistsÆ and quartz-vein stockworks. Rehabilitation at the mine has focused on creating an environmentally benign site dominated by pasture to allow continuation of the traditional pre-mine farming economy. Changing regional economics, continued urbanisation and a reduction in traditional employment opportunities has seen a rethink in the long-term rehabilitation outcomes. The community has recognised that the rehabilitated site will provide the basis of a viable tourism venture and the creation of a Heritage and Art Park (working title æGolden Point ParkÆ) is the culmination of that process.

Jan 1, 2002

Broken Hill has a long history of mining and it is without doubt a world-class deposit. It has seen production since 1885, notwithstanding the strikes that made the city infamous in days gone by and has given rise to three of the nation's leading mining companies; BHP, North and CRA. Prior to the formation of Pasminco in 1988, the mining and exploration activities were undertaken by separate companies who were business competitors and tended to operate in relative isolation. There were a few notable exceptions such as the Central Geological Survey of 1936 - 38 (Gustafson, 1939; Gustafson et al, 1950) and the Mine Managers' Association. The latter sponsored many university based research projects. At a local level there was good communication and cross fertilisation within this remote outback centre through personal contacts and professional bodies such as The AusIMM. Pasminco was formed by the merging of the lead-zinc interests of CRA Ltd and North Broken Hill Ltd. In Broken Hill this meant the joining together of North Mine and ZC Mines, the two largest mines then operating on the Line of Lode, to form Pasminco Mining Broken Hill Operations. The exception was the central part of the orebody, the original BHP, South Mine and

Jan 1, 1997

A small-charge rock excavation method based upon the Penetrating Cone Fracture (PCF) technique has been demonstrated to be capable of excavating the hardest of rocks. The PCF technique involves drilling shallow holes in the rock which are then pressurised at the bottom by a propellant charge device. A controlled fracture is initiated at the hole bottom comer and propagates in such a manner as to excavate the rock at an energy efficiency three to five times better than explosives. Due to the low flyrock velocities and airblast pressures realised with PCF breakage, the method may be used in close proximity to equipment and personnel and is thus ideally suited for integration into continuous hard rock excavation systems. Over the past 18 months full-scale testing of the PCF method has been carried out in mines in the US and Australia. This testing has utilised a 76 mm diameter gas injector for hole pressurisation and employed propellant charges ranging from 80 to 320 gm. In addition to extensive data on rock excavation performance, data on ground motion, dust, carbon monoxide and air blast have been obtained. These data indicate that none of the parameters associated with PCF breakage are detrimental to the development of PCF-based, continuous-excavation machines. Machines employing the PCF method may range from simple single-boom machines for secondary breakage and small precision-blasting jobs to integrated systems with several booms, continuous mucking capabilities and ground-support equipment for drifting and tunnelling.

Jan 1, 1993

The long continuing controversy over the Origin of fusain, whether it is a product of primeval forest fires, or of special conditions of weathering (including bacterial decay) of the vegetal debris concerned prior to, burial, has now been extended, to include the possibility that fusain is a product of the coalifaction process subsequent to deposition, so that doubt may reach even to its time of formation.The conflicting views on this point are summarised in the following quotations from two recent publications (my italics in each quotation):1. "Recent observations made in peat and brown coal deposits in Australia, England and Germany strongly suggest that practically all fusain is formed by coalifaction after deposition and 'preliminary compression. In deposits of advanced brown coal rank, it normally takes the shape of pieces of wood compressed parallel to the bedding plane; and some fragments consisting partly of fusain and partly of vitrain exhibit the same amount of compression throughout. This would seem to indicate fusinisation after burial, as hard brittle charcoal would be crushed, or else retain its original irregular shape if strong enough to withstand pressure.In some immature deposits, however, where cover is of a hydrostatic nature rather than a vertical compressionar force, occasional pieces of fusinised wood showing very little flattening are present, but such immature deposits seldom contain the proportion of fusain found in higher rank coals. In view of this, and the possibility of introduction of charcoal into peat deposits, it is felt that a small amount of the fusain in coal may represent wood charred before burial, but most of it almost certaInly originated as a product of fusinisation after burial" (Dulhunty, 1948, p.14).

Jan 1, 1953

By J Andrina, D Richards

The Grasberg is a large copper and gold open pit mine operated by PT Freeport Indonesia and located in the high equatorial mountains of Papua Province, Indonesia. The climate is alpine/sub-alpine with little seasonal variation in temperature and rainfall. The annual precipitation varies from about 3000 to 5000 mm over short distances around the Grasberg, but in general, an average daily precipitation of 10 mm per day applies and leaching of the overburden is continuous throughout the year. Mining commenced in 1988, and almost all of the overburden mined up to 2003 was potentially acid forming. The current acid drainage from this overburden is being collected and treated. From 2004 to the end of the Grasberg pit operation in 2014, approximately 70 per cent of the overburden will be potentially acid forming and 30 per cent limestone. A program of laboratory leach columns, field test pads and an instrumented full-scale dump was developed with the objective of defining scale up factors to quantify the acid and metal leaching rates and to evaluate the stockpile geochemistry and control options. The results of an ongoing seven year program have demonstrated feasible scale up between laboratory columns, field test pads and the trial dump in relation to material geochemistry and ARD evolution trends at Grasberg. The potentially acid forming waste types are highly reactive and maximum acid generation rate occurs within two to three years and that maximum copper release occurs within one to two years of exposure. The results also show that the net acid generation (NAG) test provides a good estimate for the potential acid load from overburden types. The chemistry, temperature and oxygen data from the trial dump suggest that oxidation and acid generation is occurring throughout the dump but at a decreasing mass rate with increasing distance from the toe of the dump. It is apparent that convection and/or advection are important mechanisms for the transport of oxygen into and within the dump. Key results and findings of the investigations carried out are presented and the implications of the findings for long-term ARD management at the Grasberg mine are outlined.

Jan 1, 2003

A paper describing the treatment of the Mary Kathleen uranium ores must necessarily be historical and confined mainly to a review of the four papers which have already appeared. Couche and Hartley (1958) described the development of the treatment process just prior to the commencement of operations in June, 1958. Harris, Boag and Hemingway (1961) described the treatment during the operations, and Wreford (1965) reviewed all aspects of the mine and mill, when operations were suspended in November, 1963. Harris and Steele ('1960 presented a paper especially describing the radiometric sorting operation. Some hitherto unpublished information is also presented in the paper to describe some of the peculiarities of the ore, indicate reasons for the adoption of the treatment flowsheet, and some interesting problems connected with this treatment.

Jan 1, 1968

Future hard rock mining will gradually move towards complete mechanisation which lends itself to remote control and ultimately to robotic mining. This will require different technical inputs into mining engineering and one of these is in the area of rock'mechanics. Traditional hard rock mining has had little rock mechanics input. Problems arising from high stresses and poor ground conditions have in most cases be remedied after they occurred, in the worst case by abandoning a particular stope or area and starting elsewhere. In a fully mechanised remote or robotic mining situation the financial penalty for such an approach could be severe, as a major part of the production costs will be in the development and the equipment. It is therefore imperative that a complete rock mechanics feasibility study is undertaken before an area is set up for robot mining and that a continuous stability monitoring system is installed that will predict rock behaviour well in advance of mining, such that the necessary ground control measures can be implemented without impeding the continuity of mining. This system will utilise already existing instrumentation such as extensometers and stress cells, and possibly additional improved instrumentation which has to be developed for this particular Application.

Jan 1, 1986

By Brook W. H

The history of the reduction of iron from its ores is lost in antiquity. Archreologists state that man has practised it for over four thousand years. Until comparatively recent times charcoal was the principal reducing agent for making metallic iron from its various oxidised ores. Coke was first used by iron founders in England in 1619, and its use spread gradually throughout the civilised world from then onwards. Indeed, the destruction of forests to obtain the requisite charcoal made the iron founders, both in England and America, extremely unpopular, and this hampered the iron industry to a considerable extent, until coal provided the metallurgist with a new and better fuel--coke which is used by most pyro-metallurgists today. The transition from wood to coal products for iron smelting had a profound effect on the location of iron works. Particularly was this the case in America where, in the infancy of the industry, practically each of the early States had its own iron producers, but as coal and coke replaced charcoal, there came about a concentration of the iron and steel industry around the coking coal deposits, and so today there are huge steel plants clustered around the soft coal basins in Pennsylvania and Illinois.The development of the iron and steel industry in Australia, which is comparatively recent by world standards, has been cradled in the coal basins of New South Wales. The first steel works of any consequence in this country were built near Lithgow, close by the mines which produced the coal for coking.Incidentally, these works were rather unique in that the three essential materials for iron and steel manufacture-ore, coal, and limestone-were found virtually at the works' back door.When, in 1912, the location of the proposed steel works for The Broken Hill Pty. Co. Ltd. for smelting ore from Iron Knob in South Australia was considered, the site ultimately chosen was at Newcastle, almost on top of seams of satisfactory coking coal. One of the major factors which had determined the site of the steel works was the fact that, about 1912, three tons of coal were required to produce one ton of finished steel product, and the relative economics of ore and coal haulage were much in favour of bringing ore to the coal.

Jan 1, 1947

The Bendigo Goldfield is AustraliaÆs second largest goldfield, having produced 22 million ounces of gold between 1851 and 1954. Development of the modern decline mine, initially for underground exploration and bulk sampling, commenced in 1998. The project is targeting new reefs below and along from historic workings beneath the city of Bendigo. The major technical challenge for the project is the inability to solely use drill core gold assays to estimate the grade of reefs, due to the coarsegrained nature of gold mineralisation, known as the nugget effect. In 2002, a program of bulk sampling commenced, resulting in the development of factors for converting drill hole grades to in situ reef grades. In mid 2006 commercial production commenced following the construction of a 600 000 t/yr processing plant adjacent to the Kangaroo Flat Mine portal, with plant feed being derived from four reefs in the Sheepshead and Deborah lines of reef. In early 2007 it became clear that the initial ore reserves had been overestimated, leading to an immediate change of strategy from production to exploration. A cash conservation program was also put in place. Exploration refocused onto the more historically productive Garden Gully and New Chum lines of reef, whilst a new grade estimation tool based primarily on the visual assessment of drill core was implemented. Immediate exploration success occurred with the discovery of four reefs in the Garden Gully line in early 2007. Successful step-out drilling during the year led to the decision to undertake trial mining in Gill reef. Trial production commenced in June 2008 and includes the processing of discrete ore blocks and the introduction of selective mining techniques. This paper examines the steps that have been taken to refocus exploration and to gain confidence in new exploration results, particularly through the visual grade estimation technique and assessment of trial mining Gill reef on the Garden Gully line. In addition, project factors relating to human skills, community relationships and financial management in a dynamic external environment are also addressed.

Jan 1, 2009

The difficulty in screening of ores when the moisture contents reach certain critical levels has resulted in mining circuits using wet processes for screening. While this has been acceptable in past years it is no longer acceptable in certain countries and where the mining company is looking to reduce its impact on the surrounding environment.   Various mining companies have been looking at ways to remove the need of using water, with all its inherent drawbacks and to be able to produce its desired products in a dry process.   This would have the benefits of less environmental impact and cost, (due to not requiring wet processing equipment), less power consumption (reduced equipment needed), no corrosion issues, no contaminated waste waters and reduced maintenance activities.   Until recently this has proven elusive or with technical restrictions with current available acceptable technologies for high capacity plants.   One major mining company began seriously exploring ways to overcome this dilemma so that they did not replicate their current ways of operating for their new expansion plans.   They partnered with Metso Minerals to undertake extensive groundbreaking laboratory test work and provide potential solutions as to how to solve this. The laboratory test work proved interesting enough to design, manufacture and test on the actual mining site a prototype screening machine in the circuit.   This break through in screening technology reduces the environmental impact on the area in which the mine is located by: eliminating the storage and use of water, reduction in energy consumption due to having no pumps in the plant, reduction in plant costs and the upstream affects on the environment process used to manufacture and ship the materials the plant structure is built from, and no large tailings dams to take up land space and affect the environment through groundwater/ water table contamination and the negative effects on animals and ecosystems Laboratory test were conducted and a full size machine was installed at the plant site along side conventional machines. The screen size (2.4 m wide x 6.1 long double deck) was determined by the size of screens currently in operation at the mine. The parameters that were explored were: types of screen surface (polyurethane, woven wire etc), types of screen motion (linear, circular or elliptical), angle of motion ( 40,45,55,60 degrees etc), and throw (amplitude), speed and 'g' force.

Jun 1, 2010

By P K. Seccombe

The McKinnons gold deposit is hosted by weakly deformed, Palaeozoic metasedimentary rocks of the Cobar Basin in the western Lachlan Fold Belt of New South Wales. Mineralisation comprised a largely supergene resource of 1.7 Mt of ore, grading 1.7 g/t gold, established over structurally controlled, primary gold and base-metal mineralisation in underlying, carbonate-rich meta-siltstones and sandstones of Early Devonian age. Mineralisation was associated with at least two major fluid cycles. The first cycle was characterised by four stages of vein formation. Early quartz and carbonate veins (Stages 1 and 2) and quartz-pyrite breccias (Stage-3) occurred prior to, or early in, the main regional deformation (D1). Continued D1 deformation produced syntectonic, carbonate-base-metal veins (Stage-4), primarily in dilatant zones adjacent to fold axes. The second cycle of mineralisation was an epithermal-style event, driven by a shallow, syn-D2 or post-tectonic intrusion, defined by aeromagnetic imaging. The intrusion may have exploited a jog, controlled along the basin margin by basement faults. Mineralisation produced gold-pyrite veins, associated with pervasive quartz-sericite-adularia and chlorite-sericite alteration. Highest primary gold grades are confined to quartz-adularia boiling zones. The McKinnons deposit offers an important example of mineralisation formed by multiple processes. Early-stage, base-metal mineralisation at McKinnons reflects structurally focussed, basin dewatering and metamorphic processes, typical of other deposits in the Cobar Basin. By contrast, late-stage gold mineralisation at McKinnons is magmatically driven and of epithermal style. Recognition of overprinting distinctive geological events is critical, not only in modelling ore formation, but in developing a versatile exploration concept.

Jan 1, 1999

By Willis I. L, Stevens B. P J, Stroud W. J

The Early Proterozoic metamorphic rocks of the Broken Hill (BH) Block have been recently subdivided into sixteen formations and four groups (Willis et al., 1983b, Stevens et al., 1983). This stratigraphic subdivision has relied upon recognition of distinctive mapped rock units and "associations" of mapped rock units, which characterize particular lithostratigraphic units. The rock units and rock unit associations define local ordered sequences which can be compared and correlated, thereby establishing the stratigraphic succession. In the Clevedale homestead, Thackaringa, BH City, Bores Mine-Freyers mine, Silver King mine, and Brewery Well areas, coherent stratigraphic successions have been interpreted. These areas illustrate the regional variability of the stratigraphic succession and facies changes within individual stratigraphic units. Stratigraphic type sections are located in the Thackaringa, Bores Mine-Freyers mine, Silver King mine, and Brewery Well areas. The principles of stratigraphic interpretation applied in the BH Block can be used in other areas of Willyama Supergroup outcrop such as the Euriowie, Olary and Mount Painter Blocks. The general technique may also have applicability to other highly deformed and metamorphosed terrains.

Jan 1, 1983

One of the most difficult places to ventil ate in any mine is the working face area of an advancing mine heading. With an ever changing configuration, continual modification and extension to the ventilation system is necess- ary to maintain an adequate supply of fresh air and to control mixing and recirculation. Methane emissions and high dust levels as coal is broken and removed from the face area can produce unhealthy and dangerous conditions if ventilat- ion is not adequately monitored. An understanding of the air flow patterns which develop through use of different face ven- tilation systems can be reached by undertaking underground measurements or through observations using physical models. Tests undertaken by the author to determine the adequacy of different system-configurations are discussed together with approaches adopted by others working in the United States. Various new methods have been proposed for improving face ventilation beyond that sustained using conventional brattice curtain or tubing systems. The adequacy of some advances adopted by mining companies to improve ventilation while maintaining output efficiency is discussed.

Jan 1, 1983

Standard petrographic profiles for many Permian seams from New South Wales and Queensland have been drawn up. The standard profiles of seams of the same age and from one or more coalfields were used to compile an idealized or type seam sequence for those coals in which more than half the seam profiles were similar to one another. A marked similarity existed between at least 7 of the 10 type seam sequences formed. The configurations of the vitrite-plus-clarite contents of the plies of 95 per cent of the seams could be formed from different arrangements of 3 basic sequences: (i) a two-ply sequence with a lower vitrite-rich and an upper vitrite-poor ply; (ii) a two-ply sequence with a lower vitrite-poor and an upper vitrite-rich ply; and (iii) a four-ply sequence of 3 plies with vitrite-plus- clarite decreasing upwards, terminating in a vitrite- rich ply. The third basic sequence was very similar to a succession described for some British Carboniferous coals. Eighty per cent of the Australian Permian coal seams studied began with the first (i) basic type of sequence and are interpreted as originating in peat- forming areas which became progressively drier. More than half the seams were formed in an area with a stable depositional surface level which was subject to oscillations of small amplitude.. Many (30%) were formed in an area with a steadily rising depositional surface level.

Jan 1, 1969

By J Hadjigeorgiou

The stability of open stopes in underground hard rock mines is influenced by several factors including the shape and size of the excavation, surrounding stresses as well as the degree of jointing. This paper presents a design methodology for stope analysis in jointed rock masses. The proposed approach relies on geological structural data to construct realistic three-dimensional joint network models. The stability of an open stope is determined based on a limit equilibrium analysis.

Jan 1, 2000

By Waterhouse BJ

Occurrence data of Tastubian,Sterlitamakian, and Aktastinian (all of Sakmarian Stage of Early Permian) brachiopod genera are analysed by Q-mode cluster analysis, principal component analysis, and discriminant analysis based on presence or absence of genera. Five faunal provinces and their corresponding generic associations persisted throughout the Sakmarian Stage. The additional Sasian Province incorporating the Lhasa and Shan-Thai terranes became recognisable in Sterlitarakian and strengthened in òAktastinian, implying a Tastubian-Sterlitamakian rifting event, followed by subsequent northward drift and divergence from Gondwana, and convergence with Laurasia. The nature of Permian 'Tethys' is discussed on the basis of faunal migration and abrupt changes of faunal provinciality in Lhasa and Shan-Thai terranes.

Jan 1, 1990

By B K. Hebblewhite, G Sharrock

The strength and deformation properties of a rock mass are important parameters influencing the design of civil and mining excavations or structures. The mechanical behaviour of jointed rock masses are controlled by the characteristics of discontinuities and the strength of intact rock bridges between discontinuities. To date, analytical, empirical and experimental methods have not captured the key mechanisms controlling the mechanical properties of actual rock masses with non-persistent joints. The emergence of the synthetic rock mass (SRM) in 2007 provides a promising approach for this purpose. In this paper a rock mass with non-persistent joints is analysed with the SRM model based on PFC3D. The influence of joint geometrical parameters on the uniaxial compressive strength (UCS), rock mass deformation modulus (Em) and failure mode is studied. Joint parameters include joint orientation, persistency, spacing and step angle. Prismatic numerical samples with dimensions 300 mm × 150 mm × 50 mm were generated and a sensitivity analysis of each joint parameter on UCS and Em was undertaken. The results show that of the parameters tested, joint orientation has the greatest influence on UCS. Minimum UCS occurs when the angle between the major principal stress and joint surface is approximately 60°. The joint step angle was found to have a significant effect on failure mode and a joint step angle of 90° is the most favourable joint orientation for step-path failure. The importance of joint step angle is highlighted in the discovery of a failure mode bifurcation point at joint step angles of 60° and 90° for joint orientations of 75° and 90°, respectively. For these parameters the failure mode transitions from block rotation to a new failure mode where the coalescence of cracks results in the formation of new small regularised blocks.

Sep 26, 2011

By Skinner W, Netting A. K O

Surface analysis of ore samples collected from corresponding concentrate and tailings process streams is now a widely used tool in many Australian base metal sulphide concentrators, particularly those involved in AMIRA projects. The use of tec

Jan 1, 1997