Search Documents

By Armstrong M

The highest grades of the Porgera gold deposit, Papua New Guinea, are contained in Zone 7 due to the presence of the Roamane fault, which acted as channelway of the gold-bearing fluids. Prior to the development and underground mining of this fault-controlled high-grade zone it was critical to provide grade estimates of relatively small mining units, and of the proportion of mining units above cutoff. To be applicable to Zone 7 of Porgera a grade estimation method should account for the following:1. the highly skewed and apparently lognormal distribution of the grades,2. the rapid drop off of the local mean grade and the variance as the distance to the Roamane fault increases,3. the presence of high grade pockets in the footwall, away from that fault, and4. the existence of variograms for the logs with sills parallel to the fault and without sills perpendicular to it.

Jan 1, 1990

By Piga P, Sammarco O

Ventilation and the environmental climate in the Campiano mine is the subject of this re- search. The mine is located in Southern Tuscany (Central Italy), a region where geothermal gra- dients are very high (three times the average gradient of the earth). The research produced interesting indications as to the influence of surface climatic conditions on the environmental parameters inside the mine. A close correlation has been found between dry-bulb temperature and humidity ratio of the air in the mine for dif- ferent metereological conditions and for differ- ent mass flow rate values. Variations in air enthalpy, caused only by the heat exchange with the rock walls during the flowing of the air through the mine, depends on the surface temperature values. Statistical analyses have been used to ex- press air enthalpy variations on surface tempe- ratures, on the variations of the humidity ratio that the air undergoes inside the mine and on the mass flora rate. The application in practice of the results will permit the identification of correct mea- sures to be adopted so that optimal microcli- matic conditions are produced in the mine.

Jan 1, 1986

The initially cautious approach taken towards ground support and reinforcement at the Porgera Underground Gold Mine in the Highlands of Papua New Guinea has evolved rapidly in the two years since stoping commenced. The confidence to continue the evolution process has grown from an increasing knowledge of mining conditions as stoping has progressed, to the extent that reinforcement requirements have decreased by 50 to 75 per cent depending on local circumstances. Changes to mining practices have significantly assisted and influenced this process.Empirical observations of ground behaviour, assisted by a deliberately selective extensometer monitoring program, provided the stimulus for early changes to ground support and reinforcement practices. Further optimisation of the ground support and reinforcement effort is being pursued through an active monitoring, measuring and analysis program. Ultimately, situation rather than site specific design will ensure continuing high quality ground support and reinforcement installations. However, local structural and lithological factors will continue to become more critical as the optimum position is reached.

Jan 1, 1993

By D Cotnoir, Q Liu, D Richard, M Ourriban

The difficulty in fine particle flotation has been attributed, among other things, to a low bubble-particle collision efficiency. Many technologies have been developed which aim at increasing bubble-particle collision efficiency, either by generating micro bubbles or by enlarging particle sizes. However, commercial applications of these technologies are limited. Over the last five years COREM has been actively testing fine particle froth flotation technologies with the objective of commercialisation. Several fine particle flotation technologies, such as dissolved air flotation, electro-flotation, floc flotation, selective flocculation-flotation and carrier flotation, were tested on both single minerals and ore samples in order to identify the reasons that prevented these technologies from being used on a commercial scale. It was found that the two most noticeable factors that prevented the successful application of these technologies were: Mechanical entrainment of fine gangue minerals. This was a general problem in fine particle flotation, but was aggravated by these technologies that either generated micro bubbles or enlarged the sizes of hydrophobic particles. Oxidation of (sulfide) minerals that resulted in hydrophilic oxidation product coatings. The oxidised fine particles could not be recovered by these fine particle flotation technologies effectively. Solutions to the two problems, ie gangue entrainment and fine particle oxidation, were proposed and tested. It seems that polymeric depressants with both depression and flocculation functions could significantly reduce gangue entrainment, and hydrophilic surfaces of oxidised fine particles could be modified by high intensity conditioning or controlled sulfidisation, thus increasing the recoveries of fine valuable minerals. The improved fine valuable particle flotation and reduced fine gangue entrainment along with fine particle flotation technologies resulted in much improved flotation separation of fine particles.

Jan 1, 2005

By J I Stewart

The Copper Canyon deposits, occur in proximity to the regionally distinctive formational boundary between the Staveley Formation and Marimo Shale. The mineralisation here is associated with breccias, veins, and alteration zones near the base of the Marimo Shale unit and in the underlying evaporitic dolomite-dololutite dominant Staveley Formation. The Marimo Shale unit, in its basal 60 metres, is highly carbonaceous and hosts ubiquitous but minor diagenetic (?) copper-pyrite, and on occasion, extensive albite-microcline alteration centres, pyritic (cobaltiferous)-quartz veins, and microcline-quartz_+plagioclase veins or veinlet arrays. The most significant mineralisation, such as at the Greenrnount prospect, consists of a shallowly dipping package of alteration zones overprinted by multiple generations of pink-orange microcline-quartz-chalcopyrite-pyrite-(arsenopyrite) and albite-calcite- phlogopite veins. Accessory mineralogies in most of these mineralisation styles consist of tourmaline, monazite, rutile, and apatite. Chalcopyrite (and secondary chalcocite) and gold are associated with each generation of alteration but are best developed in the later stages of veining. In the underlying Staveley Formation, which is a conformable transition between the Corella Formation limestones and the Marimo Shale, chalcopyrite (cobaltiferous)-pyrite mineralisation occurs as disseminations in pre- and syntectonic breccias, and with disaggregated silica pseudomorphs (after thinly bedded evaporitic sulphate beds) and associated dolomitised limestone-calcilutite. Although this mineralisation may be partly diagenetic in origin the 200 in thick evaporitic packages are also host to a locally widespread (2 to 4 km long and 200 to >500 metres wide) and pervasive 'redrock' styled microcline-dolomite¦hematite alteration. Within this gross alteration package there also seems to be a consistent association with narrow (10 to 100 metres wide), linear (stratabound) semi-massive magnetite-hematite-microcline and quartz-chalcedony replacement zones. Like much of the nearby Corella Formation the Staveley Formation, under the Marimo Shale, has undergone dissolution, paleo-solution karsting (breccias) and tectonic brecciation such that the precursor lithological details have been progressively obliterated. The post-diagenetic to post-tectonic fluid pathway development and metasomatic alteration history of this important lithostructural package of rocks has been traced from preliminary studies only. The ability to do so is largely due to the absence of significant regional and contact metamorphic overprinting, and the local preservation of precursor sediment profiles. It is proposed that both the base of the Marimo Shale and parts of the underlying evaporitic-limestone-dololutite have acted as conformable fluid pathways for hydrothermal and (perhaps) diagenetically derived, Cu-Au-(¦Co ¦As) K-Na-Ti-REE bearing, fluids and brines.

Jan 1, 1994

By M Hilden, G Forbes, Z Ye, M Yahyaei, F Reyes, V Jokovic

Soft sensors offer several practical advantages for the process control of comminution circuits by combining multiple conventional sensors and other data sources with real-time analysis using mechanistic, phenomenological or machine learning models. While there has been a growth in the use of machine learning techniques for developing soft sensors in minerals processing applications, this paper describes advantages and challenges of using soft sensor models developed on the basis of process knowledge. Recent experience with three new soft sensor technologies developed by the authors are discussed. The Mill Filling Inference Tool which has been implemented at several mine sites, compares SAG mill load cell and power draw measurements with outputs of a semi-mechanistic power model to estimate the mill ball and total filling in real time. The progressive wear of the mill liners is modelled, allowing the model to correct the load mass due to the mass loss automatically and to estimate the charge trajectory. This information enables the mill to be operated more confidently near its limits. A coarse-ore stockpile soft sensor as been recently developed using a 3D cellular automata-based model to track ore size throughout the pile, and estimating the live capacity and size at each stockpile feeder to the primary mills. Finally, a hydrocyclone soft sensor is being developed to monitor performance using available hydrocyclone models to estimate the size and flow balance around the cyclone in real time. The model-based soft-sensor approach aims to synthesise and analyse existing data and provide operators and engineers with process- and model-relevant information that can facilitate making better process decisions. Maintenance data has proven useful for model development as it allows soft sensors to automatically adjust and compensate for the effect of progressive wear, for example for mill liners, thus helping the models to maintain calibration throughout the equipment life.

Aug 24, 2022

By B J. Monaghan, P Zulli, X F. Dong

In the lower zone of blast furnace (BF), slag trickles down through a packed bed of carbonaceous particles in the form of films, rivulets or droplets. During its downward flow, there are significant interactions occurring between slag and other phases, ie gas and packing particles. In particular, the interaction between gas and slag is closely associated with the key flow phenomena such as loading, flooding or channelling in the lower zone of the BF. With gas introduced laterally through tuyeres and slag flowing downward from the cohesive zone to the hearth, this interaction varies throughout the lower zone and in the cohesive zone:  strong cross-flow of gas relative to the slag occurs in front of the raceway  counter-current flow of gas and slag occurs in the upper parts of the lower zone  both strong cross- and counter-current flow of gas and slag around and within the cohesive zone. These interactions can be linked to furnace irregularities, affecting smooth operation and limiting production. Therefore, understanding the gas-slag interaction and its influencing factors remains critical for BF process control. In the current review, the physical behaviour and key influencing factors of gas and slag flow are initially examined. Numerical models describing gas and slag flows in a packed bed at micro-, mesoand macro-scopic levels, are reviewed. Each simulation approach has its advantages and limitations, as well as unique assumptions when used in BF process modelling. Applications of these approaches to gas-slag flow in key identified functional zones will highlight the differences between approaches and modelling outcomes. As no single approach can fully address all aspects of gasslag interactions, an integration of different approaches is considered an effective and beneficial method in providing a more complete understanding of gas-slag flow in the BF process.

Jun 19, 2024

Over the last 100 years in the Polish mining industry considerable work has been done to assess optimum slurry, develop flexible delivery systems and adjust the fill technology to a wide variety of mining and geological conditions. Sand or industrial mineral waste materials for the backfilling of underground voids are used to control ground movement and surface deformation. This paper discusses various criteria to be considered in the preparation of a fill, including slurry properties, mine infrastructure, mining geometry, placement methods and the purpose of the backfill. This paper presents laboratory and in situ test data on the influence of materials parameters on the slurry flow in a pipeline system, stiffness, permeability, binding time and strength of a backfill, on the distribution of mixture in underground voids or the penetration between roof fall materials.

Jan 1, 1998

By E Ben-Dor, D Bakun-Mazor, Y Ben-Ari

Determining the mechanical properties of rocks is important for various civil engineering fields, including the mining of raw materials for aggregates used in the construction and paving industries. Traditionally, the mechanical properties of rocks are obtained through in situ and laboratory tests during geotechnical surveys. However, these time-consuming surveys involve many resources. In contrast, hyperspectral remote sensing methods make it possible to identify the mineralogical composition and crystallographic structure of the rock; properties that control the mechanical properties of the rocks. In this work, we characterise the mechanical properties of carbonate rocks by using a hyperspectral sensor in laboratory conditions. We collected about 150 cylindrical samples of carbonate rock, with a wide range of strength values from several rock outcrops in Israel. We used a point spectrometer in the range of 0.4–2.5 μm and a spectral image sensor in the range of 3.0–12.0 μm, scanning the samples to obtain the signature of their light reflections and spectral emissivity. We then measured the samples’ density, porosity, water absorption, and uniaxial compressive strength (UCS). We used sophisticated data mining to find statistical relationships between the hyperspectral signatures of the samples and their mechanical properties. We used this data to identify the most dominant wavelengths for predicting mechanical properties. We found that the density, porosity, and water absorption of carbonate rocks could be confidently predicted based on spectroscopy data, while the UCS of the rock could also be predicted, but less significantly. The results of the study pave the way for the development of measuring tools for the mechanical properties of rock, based on non-destructive tests of quarrying materials.

Nov 29, 2022

By A von Johannides, G J. van Hout, L F

In the past various systems have been used to plan the extraction of ore from block cave operations. These systems have varied from rather sophisticated models with empirical ægravity flowÆ rules applied to the very rudimentary models where only the recorded mined tonnageÆs have been accounted for against the available resource. The normal requirement of these models has been to only plan the movement of ground through the drawpoints. Little cognisance has been taken of the other parameters that affect the total mining operations. The intended purpose of the linear program planning system is to not only include the management, resource availability and geotechnical constraints, but to also include the mining rules. The paper will discuss the various constraints that have been considered, and attempt to illustrate where the system better serves the production system than previous ones. A brief technical discussion on the linear programming system is included.

Jan 1, 2000

By R Berry

This paper looks at two ways to estimate the bulk mineralogy of the rocks for assay intervals. The aim is to find an efficient indicator of the most common minerals in the rock. Phase (modal) analysis has traditionally been done using visual methods such as point counting and image analysis. A modern version of this process is the X-ray point counting routine using the SEM-EDS based software. These methods are too slow and expensive for routine analysis of bulk sample mineralogy at the normal assay spacing.Two sources of data were considered that provide information that can be used to determine the mineral abundance in assay samples. The most widely applied method is (semi-) quantitative X-ray diffraction (QXRD). The QXRD method is most applicable to major minerals and has limited application to minerals at low abundance. The nominal detection limit is 0.5 per cent. Values below five per cent have large errors. A second, less common, method is calculation of mineralogy from chemical assay data. Conversion of chemical analyses to mineralogical analyses depends on the unique chemical composition of each mineral. Elements only found in one mineral are easily accounted for, but many compositions are ambiguous. Deciding on the actual mineralogy is not simple. Recalculation of mineral mode from chemical analyses is more accurate than QXRD when the correct minerals, and mineral compositions, are known.Where only a few QXRD analyses are available they can be used to setup a protocol for calculation of mineralogy from assay data. Linear programming works well in this environment. The best results are obtained when both H2O and CO2 are directly measured. Loss-on-ignition (LOI) should be included if these are not available.Where both QXRD and chemical analysis are available for all samples, the best results are obtained using the least squared method to merge the data sets assuming QXRD has much higher analytical errors than chemical assays. The combined method provides more robust results because the high abundance minerals are controlled by the QXRD measurements while the chemical assays improve the precision for low abundance minerals

Sep 5, 2011

By M S. Powell, M P. Bueno

The commonly used SAB, SABC and run-of-mine (ROM) ball mill circuits can achieve high throughputs with good operating stability. However, these circuits consume a substantial amount of grinding media, which can have a substantial impact on the OPEX and the æcarbon footprintÆ, specifically when viewed as an æembodiedÆ energy input. On the other hand, fully autogenous (AG) circuits can operate at much lower operating costs, but with limited throughput. The control of AG mills, fed by ores with hard and soft components, can also be challenging, due to the sensitivity of the mill to the ratio of hard to soft components.In this paper, a multi-component modelling approach was used to demonstrate that the harder component should be used as grinding media, and its use should be kept to a minimum to avoid reduction in the mill throughput. There is an optimal blend of hard to soft, and any optimal blending condition is both ore-dependent and mill-specific. Establishing this blend is challenging, and consequently discourages the use of autogenous mills. The new modelling approach addresses this challenge by providing a quantitative prediction of the influence of blending soft and hard components in a mill. This prediction can then be used to establish the required blend for maintaining a stable and efficient operation in autogenous grinding mode.CITATION:Bueno, M P and Powell, M S, 2012. How to use hard ore components as grinding media, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 31-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By R G Warren

Most orebodies have cross-sections of less than 1 km2 and hence do not offer a particularly large target for exploration. Fortunately, although in the geological record ore deposits are small and rare and result from the exceptional coincidence of certain geological processes, these processes are mappable on a much larger, district to regional scale and constitute a mineral system in which the ore deposit is the central feature. A mineral system can therefore be defined as `all geological factors that control the generation and preservation of mineral deposits, and stress the processes that are involved in mobilising ore components from a source, transporting and accumulating them in more concentrated fonn and then preserving them throughout the subsequent geological history'. The mineral system concept emphasises that for many ore deposit types, although economically viable mineralisation may only occur on a scale of say, hundreds of metres, the total system of fluid-rock interactions that led to ore formation can extend over a distance of tens to hundreds of kilometres around the deposit. When mapped out, the total mineral system provides a far larger exploration target than the actual ore deposit itself. Important geological factors defining the characteristics of any mineralising system include: 1. sources of the mineralising fluids and transporting ligands; 2. sources of the metals and other ore components; 3. migration pathway; 4. thermal gradient; 5. energy source; 6. a mechanical and structural focusing mechanism at the trap site; 7. chemical and/or physical traps for ore precipitation. Many of these factors individually are common throughout time and space and are mappable on a regional scale. The delineation and empirical prediction of mineral systems can thus be approached by combining two components of metallogenic research. Firstly, the development of maps of regional geoscientific data and data sets of the distribution of factors significant for mineral systems in general. Secondly, the determination of the essential ingredients of particular styles or types of deposits in terms of mappable elements that any exploration program could focus on.

Jan 1, 1994

By M I. Pownceby, N Karimian, A Frierdich

These may be found with goethite through mechanisms including direct substitution or coprecipitation of nanocrystalline phases. Understanding P incorporation in goethite has significant implications for Australia’s iron ore industry as it lowers their commodity value. The current study tests a novel low-temperature technique to extract P impurities from synthetic goethite phases under O2-free ambient conditions by utilising Fe(II)-catalysed recrystallisation. The objective of this study was to examine the effect of the Fe(II)-catalysed recrystallisation of goethite on the geochemical behaviour (mobility and speciation) of co-associated P. To achieve this, we tracked changes in labile P (aqueous and 1M NaOH extractable) concentrations over time in goethite suspensions which were reacted with Fe(II)aq for 14 days under circumneutral pH conditions and room temperature conditions. Temporal changes in Fe mineralogy were investigated via synchrotron-based X-ray absorption spectroscopy. Iron K-edge extended X-ray absorption fine structure (EXAFS) spectroscopy confirmed goethite as the only mineral phase in P-free treatments while goethite (~86 per cent) and feroxyhyte (~14 per cent) were the main phases in 1.0 per cent P-containing treatments after a 14- day reaction with Fe(II)aq. According to our findings, the treatment of P-goethite with Fe(II) for a duration of 7–14 days, followed by a 24-hour extraction of the reacted solids using 1M NaOH, results in the removal of approximately 79.5 per cent of the initial P content. This removal encompasses both the aqueous fraction (~4.5 per cent) and the surface adsorbed fraction (~75 per cent) from the 1 per cent P-bearing mineral phase. Notably, this approach demonstrates an improvement in P extractability, with approximately a 10 per cent increase compared to the 1 per cent P-goethite sample that was not reacted with Fe(II).

Sep 18, 2023

By W A. Take, M McKellar, A Walsh, S McDougall, S G. Evans

Recent tailings dam failures have heightened public awareness of the hazard posed by storage facilities for mining waste, illustrating the need for a more critical examination of tailings dam breach mechanisms and the potential mobility of liquefied tailings. Knowledge from tailings dam breach studies will help improve safety and risk management through more accurate inundation maps, dam consequence classifications and emergency preparedness plans. Tailings dams differ from conventional water retaining dams, although dam breach relationships used in practice rely heavily on relationships derived for breach processes from the latter. Physical modelling offers a controlled environment to advance the understanding of tailings dam breach processes, thereby allowing for modelling of simple geometry and boundary conditions to test hypotheses. The performed experiments investigate prototypical tailings dam configurations and material behaviour, with the objective of validating numerical models that will enable practitioners to better assess and mitigate tailings flows resulting from tailings dam failures. Research conducted in the Queen’s University Landslide Flume at the Coastal Engineering Laboratory has investigated the breaching of 1 m high dams with tailings geometry by overtopping initiated by a v-notch incised in the dam crest. This paper presents the initial results of the next stage of this research comparing the outflow hydrograph following loss of containment caused by shear failure to overtopping initiated by notch flow. The two dam experiments presented are constructed with similar dam and reservoir geometries allowing for a direct comparison of the effect on the outflow hydrograph of each failure event. Preliminary outcomes suggest that although both dam failure events are triggered from separate mechanisms their geometries allow for similar values of Q_peak to be reached. Future work is currently planned to expand the shear test series to explore the influence of failure mechanism on the outflow hydrograph.

Jul 1, 2021

By S R. Grano

The selection of the proper frother, specifically for a given ore, is essential in flotation. Traditionally, strong and stable froths are required in the scavengers, where metal recovery needs to be maximised, while selectivity must be achieved in the roughers and cleaners, where grade of concentrates is the main issue. The physical properties of a froth are determined both by frother type, by process water composition and by the amount and nature of the suspended particles. The evaluation of different frothers, in terms of metallurgical performance, is complicated at plant scale, since it may lead to periods of malfunctioning of the process and unacceptable decreases in recovery. On the other hand, evaluation based on frother chemistry only, is often unsatisfactory, because the frothing response is strongly ore dependent. A procedure, and proper tools, was developed at the Wark in order to perform the screening of candidate frothers at batch scale on real pulp samples. The main parameters related to froth stability (half-life time, froth height) are measured after introducing the pulp samples into a foaming column, where different conditions in terms of frother addition, agitation and aeration can be maintained. The approach has been applied to the selection of frothers for the flotation of an Australian sulfide ore. Procedure and results are discussed.

Jan 1, 2006

By P SSrkkS

Mining is commonly seen as a typical basic industry with rough and even dangerous working conditions, heavy environmental load, and a low level of high-technology and automation with much manual work and operations. A mining operation (open pit or underground) is a very complex one consisting of many manual, physical, mechanical and logistical operations with different human interfaces and decisions. For this reason it is a demanding and potential area for all applications of automation and information technology: controlling difficult non-linear, time varying multivariable processes and machines; solving of ergonomic safety and environmental problems; automation of logistical systems; applying robotics, mechatronics, and information handling, etc. In addition to that, big economic sums are involved with these operations. On the other hand, automation technology has developed towards intelligent and adaptive systems including some from the above mentioned fields of automation. Connecting them with modern information and communication technologies makes the idea of an intelligent and unmanned mine more and more feasible in the near future. This requires intensive co-operation and co-ordination between the mining industry and manufacturers of mining machinery. This has been successfully accomplished in the five-year Intelligent Mine research and development program as well as the three years of subsequent implementation of its results in Finland. The basic elements of an Intelligent MineTM concept are:mine-wide information and data acquisition system; high-speed two-directional mine-wide communication network for real-time monitoring and control; computerised information management, mine planning, control and maintenance systems; automated and tele-operated machinery and equipment which are connected to the information system; and links to the public information networks. The degree of automation of an intelligent mine depends on many technical and economical factors. The basic precondition for such an approach is that it will improve the total economy of the mine. This paper will describe the Intelligent Mine Technology Program with the results. Also the implementation which took place during starting of a new underground mine (Outokumpu Chrome Oy Kemi Mine) will be described.

Jan 1, 2000

By P Hatherly, A Melkumyan, D Wyman

Chemical species distributions in rock sequences can be modelled using Gaussian processes (GPs) to predict the weight percentage between known data points. This method can be improved by dividing the modelled area into regions of different mineralogy. In the context of many iron ore deposits, marker shales give the initial guidance of where these regions may lie. These shales give rise to distinctive peaks in the natural gamma downhole logs, which are conventionally identified by hand. A GP method has been developed to automate this task.Once the appropriate boundary has been located on the basis of shale occurrences, chemical assays from exploration drill holes are used to find the exact boundaries of interest. These boundaries divide the drill hole stratigraphy into regions of different mineralogy, each of which display their own distinct correlations between the main elements and oxides (Fe, SiO2 and Al2O3). Iron ore shows a negative correlation between Fe and Al2O3, but in banded iron formation (BIF) there is a positive correlation between these species. Similarly, SiO2 and Al2O3 have a positive correlation in the shales and ore but a negative correlation in the BIF. Correlations obtained within ore-, BIF- and shale-dominated regions are therefore better than those obtained using the entire log and can be used to improve the results obtained when modelling.

Sep 26, 2011

By B Oostendorp, R van der Merwe, P

In order to assess whether polysaccharide depressants are strongly or weakly and reversibly bound to the surface of talc, a series of experiments was conducted on New York talc in which the floatability of the talc in a microflotation cell was determined. The talc was conditioned in solutions of carboxymethyl cellulose (CMC) or guar gum in 10-2 ionic strength Ca(NO3)2 or Mg(NO3)2. The talc was then washed with four successive aliquots of water, or cation solution, to try to remove the polymer and the flotation response of the talc was assessed. CMCs of different charge (DS) were used to assess the effect of charge on the strength of bonding. The results show that CMC and guar gum could be removed to a large extent from the talc surface by washing with water (the floatability was restored), however very little could be removed from the surface by washing with cation solution. The higher charge CMC was easier to remove from the talc planes in the absence of cations than the lower charge CMC. Thus CMC bonding to talc has been shown to be irreversible or very slowly reversible only if cations are present, implying that cations are necessary to keep the polymer bound to the surface of the planes to effect depression. The presence of ions in solution also had the effect of maintaining surface coverage of the talc by guar gum.

Jan 1, 2005

The (SA Mine at Cobar produces a mix of copper and copper lead and zinc ores fran long hole open stopes. Primary jaw crusher product is fed to two parallel primary autogenous mills followed by a secondary ball mill. Each mill operates in closed circuit with cyclones. Grinding equipment and the main operating variables are described. Copper lead and zinc flotation concentrates are produced sequentially. The control systems and operating strategies are described.

Jan 1, 1983