Search Documents

Environmental impact and rehabilitation on completion are primary considerations in obtaining approval for mine projects from government authorities.This paper focuses on the planning and commencement of rehabilitation during the mining of an open cut mine (Hedges Gold Mine) in an environmentally sensitive area in the southwest of Western Australia.

Jan 1, 1992

By M Rimes

This paper describes a technique to predict achievable head grades and likely variances from target grade for the Shovelanna Iron Ore Project, in the Pilbara region of Western Australia. The block model from which the production schedule is produced was created from a wide spaced drilling program and was classified as an Inferred Resource under the JORC Code. Ideally, production schedules and target grades would be determined using a combination of Proved and Probable reserves. However sometimes it is necessary to consider the requirements of potential off-take parties who have specific grade tolerances. A technique is needed to simulate mining sequences and grade variations early in the planning process, using an æexplorationÆ block model rather than the normal æminingÆ block model. Marketing contracts require examination whether the target grade {Fe, P, SiO2, Al2O3 can be kept constant, or must be revised during the life of the mine. A model (written in ExcelÖ using Visual Basic macros) develops a feasible, close to optimal, mine plan from block model data. Cut-off grades for minable ore are chosen. The model evaluates ore tonnage, grade and stripping ratio against depth. Outputs at this stage include plots of slices through the orebody, at nominated x, y and z coordinates, showing ore grade, waste, drill hole locations and topography. The model then searches for a feasible satisfactory mine plan. The initial grade target is the average for the identified ore blocks. The available block list (ABL) at any time is the set of ore blocks, any one of which can be mined without removing any other ore block. The entire initial ABL has an unacceptably large ætotal grade stressÆ, defined as [(Grade-Target)/Tolerance]2, summed over the four relevant minerals {Fe, P, SiO2, Al2O3}. The model trims the ABL, removing the block most harming the total stress. Trimming is repeated until the total grade stress reduces to an acceptable level. The trimmed ABL defines the first mine campaign. Removing the trimmed block set, a second ABL is exposed, which is again trimmed and mined. The process is automatic: a few seconds computation provides a complete mine plan. Re-running the model with adjusted grade limits quickly shows whether a uniform target can be achieved or whether the target must be modified during the mine life.

Jan 1, 2007

The key elements required to maintain final wall integrity and hence slope reliability are discussed. Failure modes and mechanisms in highly structured rock slopes are then reviewed. The impact of blast disturbance on rock masses in general is discussed and the relationships between the slope failure mode and blast disturbance is then explored. The question of how designers can incorporate such impacts into the slope design process is then addressed. This necessarily involves rock mass strength consideration and two case studies are used to demonstrate a recent dilemma in this regard. Some progress regarding this dilemma has also been reported for the second case study. The major conclusions are that: Slope reliability can be severely compromised if the slopes are damaged by blasting and this impact is not often incorporated into the slope design process. The location and extent of the blast damage will impact some slope failure geometries and failure mechanisms more than others. The concept of failure mechanism specific vulnerability needs to be further developed. The evidence indicates that this aspect is even more extreme for weak ground conditions. The quantification of the reduction in rock mass strength due to blast damage is not well understood and limitations exist with some recent guidelines. The use of the Hoek-Brown criterion for slopes in blocky rock masses requires considerable judgement. Further applied developments in this regard would be very beneficial to the industry. Some promising methods to incorporate blast damage estimates into the slope design process are emerging. It is good business to minimise final wall blast damage otherwise a whole range of issues relating to reduced slope reliability emerge.

Jan 1, 1999

By Wright D. C

The operation of the cyanide-sensitive Mintek/TB1 kegold electrode was studied in the laboratory, with regard to equilibration time and drift, the effects of pH, stirring, salinity, dissolved oxygen, zinc and copper(I) ions. Methods for valid calibration in the range 20-600 mg(NaCN)/L and pH values in the range 9 - 12 in the absence of copper were also studied. Increasing the salinity beyond a threshold of 40 g(NaCI)/L improves calibration and measurement. The sensitivity is 91 mV per decade change in the concentration of ionic cyanide, and output is reproducible to within 10 mV with attention to the factors listed above. However, salinity of 40 g(NaCI)/L also sensitises the electrode to interference by copper(1) ions. This copper sensitivity seems capable of saturation, suggesting a research strategy for possible remedies.

Jan 1, 1996

By Mckenzie CK

Delay scatter, although widely recognised, has rarely been studied with the aim of critically reviewing blast designs. With current trends towards increased deck charging, and the effect on the number of separate delays in blast designs, delay scatter is shown to have a rather profound influence on the control of initiation sequence and the ability to successfully con- duct pre-splitting and smooth blasting. Determination of realistic delay scatter distributions is the first step towards application to blast design. Delay scatter must be evaluated in terms of deviation from the nominal time, not in terms of deviation from the batch mean, since the latter is not usually known without specific testing, requiring accurate timing instrumentation. Computer programs using Monte Carlo simulation can then be developed to investigate the probabilities of out-of-sequence initi- ation or near-simultaneous initiation within any specified interval. The procedures have been applied to both production and development blast designs in Australia and Chile to improve initiation sequence control and to rationalise and simplify blast designs.

Jan 1, 1988

By M P. Schwarz

This paper describes modelling studies of the flotation cells used by BHP Billiton Nickel West Ltd in the slimes circuit at Mt Keith. The aim is to achieve a better understanding of the hydrodynamic limitations in the existing cells to improve nickel recovery. Computational fluid dynamics (CFD) simulations have been performed on the 100 m3 mechanically-stirred cells. The data produced by the simulations include velocity vectors, gas holdup distribution, solids distribution, bubble size, superficial gas velocity and turbulent parameters. These results have been checked and found to match hydrodynamic measurements at the plant. An analysis of the data found that one of the limitations in fine particle recovery was related to the air bubbles discharged with the tailing. The air in the discharge was caused by the high viscosity of the pulp. In the presence of fine particles, the pulp exhibits high viscosity with a yield stress. The increased drag due to high viscosity caused the bubbles to rise more slowly up the cell. This results in a significant hold-up of bubbles, some of which report to the tailing with associated loss of valuable minerals. A parametric CFD study of the operating variables shows that less air would be discharged in the tailing by decreasing the following: air flow rate,pulp density,stirring speed, andfrother addition. Simulation results indicate that these changes would cause a lowering of the air hold up in the cell especially near the discharge area. Predictions of the bubble-particle attachment rates under various operating conditions have also been calculated. Although it is possible to increase attachment rates by increasing stirring speed or by increasing pulp density, the amount of air discharged and the amount of nickel loss through the tailing will also increase. The project showed that CFD modelling is a powerful tool for studying hydrodynamic effects of bubble-particle interactions in flotation cells.

Jan 1, 2008

By S Coughlan

"A personal account of my journey from a student from suburban Melbourne in the 1970s through 40 odd years in and around the mining industry including the important events that have moulded my thinking and, as result, have formed the guiding principles of the mining contracting business and related entities that make up the Byrnecut Group. On reflection the game of chance has played a big part in the journey, from the selection of initial study based on my parents financial capability and the one and only offer of early employment by Western Mining Corporation where the formative phase of my career took place in what was the vibrant can do environment that existed in Kambalda in the 1970s and early 1980s. Subsequently the unplanned meeting with Frank Lubbock drawing me back to Kalgoorlie from Fiji in 1987 and the resultant formation of a private mining contracting business, the excitement of the mid 1980s Kalgoorlie mining environment followed by the turmoil of the 1987 stock market crash where business survival was the game, resulting in a relationship with the German based Thyssen Group.Thereafter the development of a large privately owned international multifaceted mining services group and the principles behind that growth. These include: development of strategic personnel and retention of those personnel cashflow management and debt within a private company scenario recognising opportunity for synergetic growth but insisting on market forces driving those business elements, as opposed to internal divisions group-wide sustainable business systems, particularly in relation to leading safety and training processes innovation and renewal to provide the elusive advantage in a competitive market the role of entrepreneurial small businesses in development of technology.The above principles combine to make a margin in a cut throat contracting environment, competing on the world stage against other contractors and owner mining options.CITATION:Coughlan, S, 2014. A miner’s journey, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 3–10 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

In the early ages man contented himself with the use of such tools and appliances as would assist him in the enlightenment of his labours. With the advancement of science, numerous motives, with modifications and adaptations, have been introduced to enlighten labours, and in many cases have taken the place of man, but it can hardly be said that this applies to shovels, although one of the oldest implements of labour; certainly, with the introduction of the steam shovel the labours of man have been considerably reduced, but the hand shovel of today is used similarly to that of years ago.If the principle of the hand shovel has not been improved upon, it must not be suggested that the manufacturers of this article are not endeavouring to improve its quality, and the main point with which the manufacturers have to contend is the production of an article which will give a maximum of durability combined with a minimum of lightness. In order to accomplish this they must select suitable material, and subject it to such heat treatment process that will produce a shovel having a maximum of hardness and toughness without being unduly brittle, and which will withstand the excessive wear to which it is subjected.In this article an endeavour will be made to explain (a) the manufacture of shovels; (b) the defects commonly met with-the cause of same and measures which are necessary to remedy them.Before doing so a brief description will be given of the class of steel used for shovels; this is an important factor, and a steel which is admirably suitable is a plain carbon one containing approximately 55 - 70% C., and closely resembles that used for the manufacture of railway rails. This plain carbon steel is very extensively used, although at present alloy steels are being utilised to a certain extent for shovel manufacture, and with suitable heat-treatment.

Jan 1, 1926

By Adshead ND, Blake KL, Rotherham JF, Rotherham M, De Jong G

Magnetite deposits with distinctive ¦ actinolite ¦ apatite -bearing gangue and spatially-extensive sodic-calcic wall rock alteration occur in both Proterozoic metamorphic terrains and Mesozoic-Tertiary magmatic arcs. Examples from both settings constitute significant sources of iron ore (e.g. Kiruna, Sweden; El Romeral, Chile) and some host major Cu-Au deposits that have a local association with K-silicate alteration (e.g. Cloncurry district, NW Queensland; Copiapo district, Chile). A growing body of evidence points to a hydrothermal origin for these systems involving high temperature, low S oxidized fluids. The Cloncurry magnetite-Cu-Au deposits are products of the local structurally channelized influx of a specialized high salinity ore fluid into larger-scale alteration systems developed during pluton emplacement at greater depths than those associated with subvolcanic (porphyry) Cu-Au deposits. The geological characteristics of deposits in magmatic arcs are consistent with a similar mode of origin albeit in rather different tectonic settings.

Jan 1, 1995

The mathematical modelling of rock fragmentation by blasting is one of the most difficult and challenging problems of applied mathematics. Not only is complex mathematics required but there is incomplete understanding of the basic physics and chemistry involved. The possibility of getting the physical basis of a model correct by simple mathematical and experimental procedures is demonstrated for the novel process of fragmenting rock by high-pressure arc discharges. While the importance of obtaining the correct physical basis for a model is emphasised, high-pressure arc induced fragmentation of rock is shown to be a powerful laboratory tool for the study of blasting.

Jan 1, 1990

By R Huntley, D Sims

Pajingo gold mine produces over 240 000 oz Au per year from underground mining using longitudinal bench stoping methods with a 15 m sublevel interval. Average mine head grade is around 12 g/t Au, contained within quartz veins between 0.5 to 16 m wide. The veins dip steeply (>60¦) and exhibit strike variations which lead to many curved and meandering drive/stope geometries. Unplanned dilution at Pajingo is predominantly controlled by fault planes that subparallel the vein and commonly lead to slabbing failure from the stope walls. Initial efforts at determining maximum spans were based on using the Stability Graph method of stope stability. However the method had a number of shortcomings that did not address mine site observations, including previous mining, interaction of different joint sets and the presence of discrete shears which resulted in poor prediction of stability. A method was developed to rate the risk of dilution for a stope based on observations made in the ore drives. The method utilises profile mapping of the ore drive, structural features observed and the orebody itself, on 10 m spaced sections along the ore drive. A matrix of factors determines the dilution risk for stoping at the time of mapping and the rating is transferred to longsection plots in the office. The dilution risk rating is used to determine the position and density of cable bolt support aimed at lessening the risk, and can be used to review blasthole designs prior to finalisation. The method has been used for more than two years and has proven to be a good indicator of potential unplanned dilution (ie waste outside of ring design). A recent review of the dilution risk mapping process has indicated it is assisting in reducing the impact of dilution at the operation and has the scope to be utilised further in the design process.

Jan 1, 2002

FOR some time it has been recognised by the Metallurgical Staff that the presence of pyrite in the ore was adversely affecting the grades of the flotation concentrates.Following experimental work, it was decided to change over from the acid circuit in the mill to an alkaline circuit. The following description sets out the procedure adopted, -and the results obtained when such change-over was made.The Zinc Corporation ore consists mainly of galena, marmatite, calcite, and quartz, with smaller quantities of pyrite, fluorspar, and rhodonite.A clean specimen of marmatite picked from the ore assayed 53.4% zinc, and 10% iron, with no lead or insoluble. However, as zinc concentrates have been, at times, produced in the plant assaying over 53% zinc, and with only 8.7% iron, apparently the picked specimen of marmatite did not represent an average composition.The average would probltbly be between 8 and 9% of iron, and from 53.5 to 54.5% of zinc. It is obvious, therefore, that from this ore it is not possible to produce zinc concentrate of a higher grade than this average figure.In the Colorado School of Mines Quarterly for April, 1928, Vol. 23, No. 2, on page 47, we find the following statement:As the zinc in the ore exists as marmatite, which contains approximately 54.5% zinc and 10% iron, 49% zinc in the concentrate may be considered high.This statement refers to the ore treated in the Sullivan concentrator, owned by the Consolidated Mining and Smelting Company of Canada Limited.

Jan 1, 1930

By S D. Golding

The current study integrates hydrogeochemical and stable isotope results to investigate the sources and evolution of acid mine drainage at the historic Mount Morgan gold mine in Queensland, including the controlling factors and mechanisms of sulfate formation. The open pit and seepage sumps contain acid-sulfate waters and show elevated Al, Cu, Fe, Mn, Pb and Zn values. Samples collected from the Dee River bordering the mine site are less acidic, with lower concentrations of dissolved metals that gradually attenuate downstream from the mine. Concentrated acid mine waters has lead to formation of efflorescences consisting mainly of hydrous Fe-sulfates. The results of the ongoing isotope analyses on water samples show distinctive grouping of the data. The range of the sulfur isotope values for dissolved sulfate in samples from the open pit and sumps (d34S = 2.1 to 3.0 per mil) are similar to those of sulfides in the Main Pipe mineralisation (d34S = - 0.2 to 2.8 per mil). The lack of fractionation between sulfides and sulfate indicates that intermediate oxidation states of sulfur are not significant and makes this technique a useful tracer to identify the sources of sulfate. The Dee River samples, on the other hand, have heavier sulfur isotopes (d34S = 2.8 to 5.0 per mil). These samples may contain dissolved sulfate from æinternal sourcesÆ in the river basin, show local bacterial reduction or indicate a simple mixing trend. Further isotope analyses including oxygen isotopes of dissolved sulfates will enhance the interpretations.

Jan 1, 2003

We can look at the water treatment and management strategies at some recently commissioned mines and minerals processing sites to see the likely future of water in mining. The future of water in mining will be based on a holistic approach to understanding the site water balance, appropriate treatment, reuse where possible, and environmentally managed discharge where required. This paper describes advanced and innovative water treatment and reuse processes as used by mines and mineral processing operations from around the world. Underground mining can often require dewatering to prevent groundwater seeping into and flooding the mine workings. Mining and processing often accumulates wastewaters in a tailings dam. The mine water can contain contaminants such as dissolved salts, iron, arsenic, manganese, heavy metals and acidic and odorous sulfates. On-site reuse, environmental discharge requirements, as well as community needs for water, drive mine operators to consider the most appropriate water treatment process. Mining water treatment for the future is described using case studies of innovative processes. The case studies include treatment of mine dewatering water for beneficial application from Australian mines, Ballarat Goldfields and Bendigo mining, treatment of produced water from oil and gas projects, and treatment for arsenic removal of tailings water from mining and processing at Goldcorp mines in Canada. Advanced and innovative processes including membrane filtration, reverse osmosis at extreme conditions, advanced biological treatment and water management are all part of these case studies. This paper uses real case studies of advanced and innovative mine water treatment processes to explain and examine the technology and the reasons for designing specific processes. The focus is on innovative processes that may be more widely used in future mining û where the water is used for sustainable environmental discharge or treatment to a quality that can be beneficially used by the mine or the local community.

Jan 1, 2008

The number and severity of sulphide dust explosions in underground metalliferous mines have increased in recent years, despite various methods used to prevent or inhibit them. A dust explosion occurs when a cloud of combust- ible dust in an oxidizing atmosphere is exposed to an ignition source with sufficient energy to ignite the dust. A computer blast simulator model was used to investigate the movement of the fractured rock, temperatures and volumes of the explosion gases in a 70 m high, 24 m wide open stope.

Jan 1, 1988

Depletion of shallow ore reserves is forcing the South African gold mining industry to exploit reefs at ever-increasing depths. By 2010 around 30 per cent of South African gold production probably will come from depths greater than 3 km (Johnson and Schweitzer, 1996). At such depths, virgin stresses will rise significantly, producing complex rock engineering problems (Malan and Basson, 1998). Concern over structural instability at depth has led planners to seek a technology capable of ædetection of geological structures with a displacement of 2 m or greater (or as appropriate to the mining technique) 200 m ahead of mining at an acceptable costÆ. Borehole radar probably is such a technology. Cover holes are drilled routinely ahead of development. The evaluation of its candidacy for a tactical role in ultra-deep gold mining dependsùamong other thingsùupon establishing the electromagnetic characteristics of the environment hosting significant gold reefs. The Ventersdorp Contact Reef (VCR) is one such reef. Recent borehole radar field trials, presented here, suggest that the VCRÆs overburden is a remarkably translucent, clutter-free dielectric with a Q of ~35 and that the VCR itself is the dominant radar reflector.

Jan 1, 2002

By Chowdhury P. J R, Biswas S. K

Recovery of metallic values from lean-grade raw materials as well as from secondary/intermediate industrial products is of immense importance to a country like India which is not endowed with extensive sources of copper and nickel. The results of a few studies carried out in this area are described in Part-I and Part-II in this article. A novel anode casting system, specially designed for a small copper refinery which had been set up to produce copper wire bars/rods is described briefly in Part-III.

Jan 1, 1992

By Lawson F

The leaching behaviour of BHAS copper matte in oxygenated acidic sulphate chloride solutions at 85¦C has been studied using samples containing 34% copper, 41% lead and 12% sulphur. Copper sulphide in the matte, essentially Cu2S was found to leach in two distinct stages. Similar to the behaviour of pure chalcocite, copper dissolution in the first stage was affected by the availability of oxygen in solution. The presence of chloride ions in the leachant was essential if there was to be any leaching in the second stage (which usually commenced after about 40% of the copper had been taken into solution). Lead sulphide in the matte was oxidised to lead sulphate and formed a shell around the partially leached matte particles. Electrochemical studies showed that this lead sulphate and/or sulphur produced during leaching can form a passivating layer around the copper sulphide. However, this layer was disrupted when chloride ions were present. A Plackett-Burman analysis was used to determine the species in the recycled leach solution that affect the leaching of copper. Under the experimental conditions used, in the first stage the rate of copper dissolution was influenced by the concentrations of sulphuric acid, Zn(II), Cu(II), Fe(III) and Cd(II). In the second stage, the rate was futher modified by the concentrations of Cl(I) and As(V) ions. In solutions of low acidity and high As(V) concentration, insoluble copper arsenate formed which coated the partially leached matte particles and acted as a barrier to futher reaction.

Jan 1, 1989

By G Giles

One of the main tools used by mining operations to mitigate the risk of rock burst is the installation of a so-called ædynamic resistantÆ support system. Such systems are designed to absorb the impact of shockwaves created by mine-induced seismic events. Dynamic support must be strong and capable of sustaining high loads and, at the same time, they have to be flexible and accommodate large deformation. A dynamic support system is therefore a system capable of absorbing a high quantity of energy. Ground support systems are composed of rock reinforcement (rock bolts or cable bolts) and surface support (mesh or shotcrete). In terms of surface support, fibre-reinforced shotcrete is increasingly seen as the industry preferred solution when difficult ground conditions are experienced, including areas of high seismic hazard. A thick layer of shotcrete is certainly strong but it is by no means flexible. Normal weld-mesh has some flexibility, but it is not very strong. The Australian Centre for Geomechanics (ACG), in collaboration with Onesteel Reinforcing Pty Ltd, is currently working on a new high-energy absorption mesh that combines strength and flexibility. The new mesh can be installed with a jumbo, in a similar way as the widely used sheet of weld-mesh. This paper describes the development of this new mesh system.

Jan 1, 2008

By R Ashworth, S J. Hall

During trials which began in May 2005, traditional steel dump bodies for transporting iron ore on 220-tonne haul trucks at a Labrador iron ore mine were compared to a novel rubber suspended dump body. Loads were measured and compared over some 93 700 loads, representing more than 20 Mt transported. Maintenance costs and downtime were also measured over the course of the trial, which lasted nearly one year. This paper outlines the parameters and results of the trials. Parameters measured included payload and production improvements, carry-back reduction, downtime due to body maintenance, and wear on the floor of the suspended dump body. These parameters were then compared to those for conventional steel dump bodies in use at the mine, and conclusions were drawn. The resulting comparisons were significantly positive in favour of the new suspended dump bodies, confirming that each truck could haul an additional 41 000 tonnes per year, that downtime hours could be considerably reduced, and that body availability and service life can be extended through use of the suspended dump body. There was also a high level of operator acceptance of the suspended dump bodies due to less loading shock and a smoother ride.

Jan 1, 2007