Search Documents

By A Garg

Squeezing can occur both in hard rock and in jointed rock mass as a result of over stressing. It is related to time dependent shearing, ie shear creep and is associated with the volumetric expansion (dilation) and radial inward displacement of the tunnel surface. While planning a tunnel in hard rock under a high cover of the order of 2 km it is desirable to identify the potential squeezing ground conditions and to select appropriate excavation technique and the support measures. There are several solutions to counter balance the squeezing ground viz over excavation of tunnel profile, assessing appropriate excavation technique, provision of a ductile primary support and time for providing tunnel lining. Low drivage rates and high cost due to support failures requiring rectification arising out of poor anticipation of tunnel closures and support pressures are major problems associated with tunnelling under squeezing ground conditions. Under squeezing ground conditions, the deformation will be gradual, therefore, in order to absorb deformations yielding supports are quite useful as primary support which provide a reliable low initial support pressure and permit uniform stress relief of the surrounding rock along with preventing rock from ravelling. The paper discusses the various factors which influence the selection of appropriate excavation technique and support measures in hard rock under squeezing ground conditions.

Jan 1, 1999

By P Trotta

The paper provides a structured methodology to investigate metallurgical problems within the operating concentrators. The strategy uses classical metallurgical data analysis as well as pulp, solution and surface analysis to determine the reasons for particular behaviours. The approach applies equally to all mineral-processing operations. To demonstrate its effectiveness a case study, based on work conducted at Pasminco Rosebery Mine, is described. In this work, the classical metallurgical analysis indicated that a significant amount of sphalerite reporting to the lead concentrate occurred as liberated particles. A combination of pulp, solution and surface analysis supported the hypothesis that the liberated sphalerite was recovered by inadvertent activation by lead ions. Laboratory studies have indicated that the use of sodium carbonate, by itself and in combination with zinc sulphate and sodium cyanide, when added to the lead regrinding mill can depress sphalerite flotation, resulting in an improvement in the lead grade/recovery curve. When this approach was tested in the plant other more dominant issues masked any positive effect the addition of sodium carbonate may have had. The plant trial highlighted the real need for additional regrinding capacity.

Jan 1, 2002

By McCarthy J

In both the U.S.A. and Canada regulations concerning the reporting on mineral resources and especially ore reserves have been established. The regulations are virtually identical for the two countries with the main exceptions being who is franchised to write the report and how the various reserve categories may be used in reports to the public. Both countries divide ore reserves into "proven", "probable" and "inferred" categories. "Proven" reserves are those for material for which tonnage is computed from dimensions revealed in outcrops, trenches, underground workings or drill holes and for which the grade is composed from the results of adequate sampling. "Probable" reserves are those which are less well defined than "proven" while "inferred" reserves are generally those which may exist through geological and geophysical interpretation. The AusIMM/AMIC draft guidelines as proposed for use in Australia define more rigidly the ore reserve categories into "proved" and "probable" terms, which can only be applied following a full and favourable analysis of economic, mining, metallurgical, marketing and sociopolitical factors. If the ore reserves are not supported by this analysis they are placed into a "resource" category. Proper application of this proposed Australian model could prove useful when dealing with grass-root prospects or mining properties in the pre-feasibility stage. Combined with competent reporting, use of the proposed guidelines should ensure standardised and more verifiable analysis/valuation of a company's mineral assets.

Jan 1, 1987

By P D. Munro

The Mine to Mill concept, as it has become known, is a philosophy which is being increasingly embraced by mining companies committed to increasing their profitability through better integration and global optimisation of their mining and processing operations. Autogenous (AG) and semi-autogenous (SAG) mills are the principal primary grinding devices currently in use, their performance is particularly sensitive to feed size distribution. Most efforts to-date have centred on modifying and controlling the run-of-mine (ROM) size distribution to maximise grinding mill throughput. The complexity of the interaction between ROM size distribution, primary crusher product and AG/SAG mill performance precludes the trial-and-error approach as an effective means of determining the optimum blast-induced fragmentation size distribution. To overcome this limitation, the Julius Kruttschnitt Mineral Research Centre (JKMRC) has developed modelling and simulation techniques that are able to accurately reproduce both the fragmentation processes during blasting and the subsequent performance of the comminution circuit. These models are tailored to suit local ore types, rock structure and comminution circuit design and calibrated using high quality field data. MIM Holdings Limited (MIM) have been particularly active in the Mine to Mill area and have instituted optimisation programs at three of their associated base metal operations viz Alumbrera, Ernest Henry and the Mount Isa Mines. This paper describes these programs with particular reference to the data acquisition and modelling phases, the predictions of potential productivity gains and the extent of the realisation of these gains to-date.

Jan 1, 2000

As a number of underground fires have unfortunately happened in the Broken Hill mining district, the writer trusts that a paper dealing with such a subject may prove of interest. To simplify matters, the subject is classed under three mainheadings- I Origin of fires; II Methods of subduing them; III Precautions to minimize the risk of their occurrence.Underground fires may be started in three ways - arson, spontaneous combustion, or carelessness.With regard to the first-mentioned cause, direct evidence is usually lacking to prove that any fire has been caused maliciously; Though definite proof of spontaneous combustion having been the cause of a mine fire has not been brought forward, nevertheless it should be considered, especially in the case of sulphide ore bodies of a more or less friable nature. The writer has been informed on reliable authority that in an open stope on the...

Jan 1, 1911

Production scheduling is an important element of the mine planning process. The production schedule specifies the quantities of mineral to extract, the source of this ore, the timing of extraction and, where necessary, the quantity and timing of backfill placement. These details are important in linking long-term strategic goals to short-term operational planning. Mine scheduling techniques form the basis for communicating information concerning the overall impact of design and planning changes to a wide range of people at many levels within an organisation. Consequently the techniques used for mine scheduling must support the decision-making process by consistently providing high quality schedules in response to revised and updated data. A new mixed integer programming (MIP) model has been developed to generate optimal production schedules for underground stoping operations. The model maximised the before-tax Net Present Value of the production schedule while satisfying constraints such as contained metal tonnage, hoisting capacity, stope geometry relationships and stope backfilling demands. Zero-one variables were used to represent the decision to extract or backfill each stope in a particular time period. Continuous variables, capable of having non-integer values, were used to denote the quantity of ore or backfill associated with a specific stope in a given time period. A case study is presented to demonstrate the significant improvement in before-tax NPV over a comparative manual production schedule in a large underground mine. The MIP model allows for further modification to reduce solution times and meet the needs of individual mines.

Jan 1, 1995

By Morland R

Recent influence of backfill stability on stope production in the Copper Mine at Mount Isa Mines Limited is described. Changes to the mining process to improve fill stability are described, including increased focus on fill performance, modifications to extraction techniques, increased fill quality, changes to drill and blast practice, and research into backfill stability. Several case studies are described.

Jan 1, 1995

By Baynes F. J, Bermingham A. G

The 6000m long King Headrace Tunnel will be driven through hard Owen Conglomerate in the Eastern third and feldspar porphyry in the Western two thirds, with the anticipated hardness up to 350MPa unconfined compressive strength. Since the Commission had not driven a long, large diameter tunnel for some twenty years, major research was undertaken to assess the current tunnelling trends. Tunnel boring machines were compared with drill and fire equipment. Rail equipment was compared with rubber tyred equipment. Tenders were called with tenderers invited to submit alternatives if desired. Commissioning and production excavation using the equipment is discussed with the final conclusion being that the individual items of equipment purchased combined to make an efficient hard rock drill and blast system capable of progressing through all rock conditions likely to be encountered on the King and Anthony Schemes.

Jan 1, 1987

At Renison Limited, on the West Coast of Tasmania, modern trackless decline mining is practised to exploit the various tin bearing sulphide deposits. With footwall accesses, one of three adaptations of horizontal mechanised cut and fill, 1. unsupported, 2. pillar supported,and 3. unsupported - resuing is used to stope each defined ore block. The stoping method is basically determined by the dip and true thickness of the ore with emphasis on high ore recovery. Extreme flexibility is possible by the selective mining of stope lifts, the consumption of development waste as fill and the utilisation of the same mobile equipment in all phases of production. This has resulted in high productivity and low cost per tonne of ore.

Jan 1, 1977

Before any accident prevention and total safety programme can succeed, a safety concientiousness or attitude needs to be implanted in the employees' minds. Psycholog- ical and physiological conditions play a vital role in accident causation and prevention. Both need attention in a good safety programme, but working place conditions and environment are more easily corrected. However, the challenge is to change attitudes in the minds of men - psychological factors in accidents. To do this does not require a Safety Officer, but does require a Safety Adviser. At Blackwater mine a Safety Adviser is available to all sections of the organisation to guide and assist, to provide data and material to use at meetings, to help in accident investi- gations and to help organise training. To eventually achieve total commitment requires every member of the management team to be a salesman towards all around selling an attitude to safe working, a way of life. At Blackwater mine the workforce is young overall with most employees being under 40 years old. Psychologically this is a quite different problem to a balanced ages working group. A great deal of effort is needed to communicate with the younger, articulate, better educated employee who is also generally a skilled operator in the capital intensive

Jan 1, 1975

The flotation circuit handling Peko ore at Peko Mines N.L. was examined in July 1970 with a view to determining simple changes in circuitry or reagents which could improve the grade and recovery of the final copper concentrates. The investigation included sampling over one shift followed by detailed testing of the samples by sizing-assays, sizing-mineralogy and sizing-liberation. Mass balances were carried out over total streams, the component minerals and the copper contents. Some laboratory work was carried out to assess the effect of salinity on flotation. In order to handle the sizing-mineralogy calculations a computer programme was set up. The raw data were corrected for locking factors, then mineral and elemental distributions cal- culated for each screen fraction and the total sample. Calculated assays from grain counting were compared with chemical assays. Recoveries through the size-ranges re- vealed very rapid flotation of copper minerals at sizes below 350 mesh. This pointed to a possible circuit improvement by desliming rougher tailings ahead of the scavenger stage. A strong correlation was found between water in concentrates and gangue recovery for the subsieve sizes. This pointed to clean water additions to the cleaner circuit as a way to 1 Project Consultant, The Australian Mineral Development Laboratories, Adelaide, South Australia.

Jan 1, 1972

Hong Kong continues to display a remarkable enthusiasm for undertaking ambitious tunnelling schemes despite apparent recessions in the Asian economy. This paper provides an outline of tunnel projects currently under construction, those recently tendered and a glimpse of the extent of forthcoming projects which, according to Government sources, carry a price tag of HK$ 200B. Committed works will cost about HK$ 15B and involve a variety of TBM and drill and blast tunnels. These include the recently tendered works for KCRCÆs West Rail and MTRCÆs Tseung Kwan O railway extension, together with five no retendered TBM drives for the Strategic Sewage Disposal Scheme (SSDS) following forfeiture of the works by the Campenon Bernard-Maeda JV in mid-1997. The JV claimed unreasonable specifications leading to unacceptable levels of water inflow and dangerous working conditions. Key technical issues that are now arising in Hong Kong are:the general use of design and build contracts for bored tunnel contracts;a trend to accept TBM options for relatively short drives in urban areas;the use of æfixed-priceÆ contracts which in the current competitive market, can encourage tenderers to take contractors to take very high risks; andthe difficulty of predicting and managing water inflows in rock tunnels.This paper also includes a new empirical method of predicting water inflows in rock tunnels, and makes recommendations for managing these on-site.

Jan 1, 1999

By Nettle W. H V

THE past few years have seen a considerable expansion of the roasting of blende in Australia. The bulk of this blende is Zinciferous concentrate from Broken Hill and now forms a very considerable source of sulphur for the acid manufacture. It will bereadily conceded that Australian sentiment is in favour of utilising all known potential wealth, especially that won from below ground, as this once disposed of is gone forever. If Australia does not make sulphuric acid from her sulphide ores we may be sure that the purchaser of these ores will do so if in any way possible. It must not be assumed, then, that the difficulties met are mentioned with the idea of undue criticism, but rather to show that, although most of the intial troubles have been overcome, there are still a few to be encountered; and with the hope that comment brought forth will aid in the solution of the problems facing an industry at present little more than in its childhood as far as Australia is concerned.Blende roasting is done in mechanical furnaces of various makes, and mostly without the aid of other fuel than the sulphur in the ore. It will be our aim to touch on the various difficulties in the order in which they occur in the train from furnace to acid plant.

Jan 1, 1926

By J Koppe, J F. Costa

A fundamental error of sampling occurs when a sample is extracted from a larger mass of ore or lot. The act of sampling requires that all particles belonging to the lot have an equal chance of being extracted. This type of sampling is called unbiased sampling. The sampling equipment (herein referred to as the sampler) should be constructed with some additional mechanical characteristics to guarantee that the samples will be unbiased. Samplers, extracting increments from a continuous flow, such as a conveyor belt, collect aliquots at regular time intervals. These time intervals relate to the number of aliquots extracted from a given mass of lot, whilst passing through the continuous flow. The frequency of extractions will influence the precision or the error of the sample (integration error). Further, the ore variability influences the amount collected from the continuous flow. Normally, the sampling protocol utilised is designed for the extractions obtained from the conveyor belt, omitting any error committed during this operation, ie the error of extracting from the continuous flow. This study aims to analyse the error of sampling a continuous flow by using a variogram with added on auxiliary functions. Each different piece of material passing through the flow will exhibit a distinct temporal variogram, which should influence the frequency of the samples being extracted for each chosen sampling error. The methodology used is presented in the form of a case study from a coal processing plant.

Jan 1, 2005

By R Hall

The magmatic arcs of SE Asia and SW Pacific contain some of the worldÆs major magmatic-hydrothermal gold deposits. Most gold deposits in SE Asian and SW Pacific arcs formed during periods of plate reorganisation rather than during periods of normal or steady state subduction. These plate reorganisations were caused initially by the collisions of the Australian Craton with the Philippines-Halmahera Arc and the Ontong Java Plateau with the Melanesian Arc at ~25 Ma. A second Mid-Miocene period of mineralisation accompanied plate reorganisation following maximum rotation or extrusion of Indochina and cessation of spreading in the South China Sea at ~17 Ma. However, the vast majority of deposits from New Zealand to Taiwan formed since 7 Ma during an important period of tectonic reorganisation that accompanied and followed changes in the relative motion between the Indian-Australian and Pacific plates between ~8 and 3.5 Ma. Magmatism in unusual tectonic settings produced the most abundant and largest deposits with many deposits associated with high-K calc-alkaline, shoshonite, adakite and alkaline magmatism. In particular peak mineralisation appears related to melting of sub-arc lithosphere that has been previously modified by subduction. During large-scale plate reorganisation this can occur towards or at the end of a period of normal subduction, following arc collision or accompanying subduction reversal at approximately the same time in different parts of a complex system of arcs such as in SE Asia and the SW Pacific.

Jan 1, 2005

By S E. Box, J L. Mauk

The Middle Proterozoic metasedimentary rocks of the Belt Supergroup contain important metallic mineral deposits like the diagenetic sediment-hosted stratiform copper mineralization, including the Troy (Spar Lake) deposit and the epigenetic hydrothermal veins in the lower Belt and Ravalli Group in the Coeur d'Alene district. Magnetite (Fe3O4) is a common and widespread accessory mineral in these rocks and can have multiple origins including ore stage in deposits, mobilization stage in source rocks, metamorphism of red beds and alteration mineral in thin halos enveloping Ag-rich veins in the Coeur dÆAlene district. As shown in several classic studies, the composition of magnetite from igneous rocks varies significantly in response to controlling factors such as melt composition, temperature, silica activity, and oxygen and sulphur fugacity. Therefore, the distinctively different geologic settings within the Belt Supergroup strongly suggest that there may be differences in the magnetite compositions. However, initial microprobe analyses detected no variation in magnetite composition.   Three possibilities may give an adequate explanation for these initial results: 1.      the magnetite formed primarily as pure Fe3O4, 2.      one or more tectonothermal events led to regional scale re-equilibration that affected all rocks in the field area, and 3.      the variations in the composition are below the detection limit of the microprobe.

Jan 1, 2007

By Peng SS

This paper presents a number of mathematical models for predicting the different phases of the complete surface subsidence process associated with underground longwall mining. A computer program developed based on the mathematical models is briefly introduced.

Jan 1, 1992

Key incompatible element ratios for metabasalts from the Early Permian Croisilles and Patuki Volcanics, South Island, New Zealand, provide constraints on the tectonic environment in which their precursor ophiolitic protolith formed. Two geochemically distinct metabasalt suites are recognised among both the Croisilles and Patuki rocks. Metabasalts from one suite exhibit the geochemical signatures of depleted tholeiites from oceanic spreading ridges (N-type MORB) or spreading centres in evolved back-arc basins. These N-type tholeiites show high Zr/Nb ratios (Zr/Nb = 37-62) and are depleted in light rare earth elements (LREE)((La/Y)N

Jan 1, 1987

By Watson D. F

Armstrong's (1983) criticisms of PhiIip and Watson's (1982b) note on optimal drilling patterns are based on misinterpretation, supported by errors in geometry. Furthermore, Armstrong argues conceptually from the perspective of Matheronian geostatistics, as does also Rudenno (1983a, b). Thus, both authors embrace a global, probabiIistic method of assessing spatial data sets, an approach that must be contrasted strongly with local, deterministic interpolation methods. Some of the important assumptions of geostatistics are outlined and the non-unique nature of the method discussed. A probabilistic approach can be judged appropriate when exploration data are erratic, or known to be unreliable, or when extrapolation is desired. Where data are treated as exact, kriging can give the most biased result if tested against other interpolation methods. We reiterate our previous conclusion that the equilateral triangular grid is approximately 30 per cent more efficient (in terms of numbers of drill holes) compared with a square grid for the same maximum interpolation distance. This is simply due to the improved isotropy of sampling. New, locally-based, deterministic methods for computing ore reserves seem to be required.

Jan 1, 1984

Metallurgical accounting can be defined as the monitoring of the valuable metals from the time the ore is broken at the primary crusher until the time that we have the saleable products and residues. The overall purpose of metallurgical accounting is to provide management with up-to-date inform- ation that can be used to control mining and metallurgical oper- ations. The decisions that are taken on the basis of the information that the metall- urgical accounting system provides should result in improved control and, ultimately, increased revenue. The current state of accounting is a result of an extended evolutionary process and will continue as process plants bec- ome more sophisticated. Differences in mine æcall factorsÆ and grade control reconciliation can lead to frustration between the siteÆs geoscie- ntists and its metallurgists leading to a level of distrust in the mill grade. Metallurgical accounting is not included in sufficient detail in undergraduate courses and the acceptable industry standards have developed based on what is considered acceptable to industry personnel and consultants. There is now the AMIRA P754 Metal Accounting, Code of Practice and Guidelines Handbook or reference manual. Computer based databases and spreadsheets have transformed tedious bookkeeping into an important management tool. Over time these standards have improved with developments in analytical procedures, weighing technology and sampling. This paper provides anecdotal examples of problems and improvements observed over a number of years within the gold industry in Australia and overseas.

Jan 1, 2009