Search Documents

By Frank W. Cole, Sharanjit S. Dhillonn

A new method has been developed for calculating flowing bottom hole pressure in a gas well, using as a basis the general energy equation. Fundamentally, the method shows that a plot of flowing pressure versus depth for a gas well can be represented as a series of incremental .straight lines, with the accuracy in-creasing as the number of increments increase. It is shown mathematically that for most cases the slope of the flowing pressure versus depth curve is essentially constant, in which case a single calculation based on surface conditions will yield acceptable results. In all cases studied no more than two iterations were required for very good accuracy, and in most cases only one iteration was necessary. Several example calculations are shown and the results are compared to other commonly used methods of calculating bottom hole pressures These examples show that the method provides answers which are at least as accurate as other methods usually used, and results in a considerable reduction in computation time.

Jan 1, 1960

By Sanat Talmaki

Construction and mining worksites pose unique challenges to workers and equipment operators due to their dynamic and unstructured nature. Narrow haul roads, crowded work spaces and presence of workers and equipment in close proximity, combined with large blind spots and overall poor visibility afforded to operators lead to collisions and run-over-type accidents between equipment, workers, and other entities that may be present on the jobsite. Operations that involve machine-infrastructure interaction, particularly in the case of concealed infrastructure such as excavation and drilling lead to unintended strikes between the equipment?s end-effect or and the infrastructure. Such accident-prone scenarios can be avoided by providing operators with real-time feedback and warnings using 3D visualization and proximity monitoring of the entities present in the equipment?s vicinity. Thus the jobsite in the real world is abstracted and represented in a 3D virtual world. However, this requires the ability to create a seamless link between real-world sensors present on the equipment and/or the jobsite and the virtual environment. This paper describes a non-restrictive acquisition allocation framework that allows position and orientation sensor streams from construction and mining job sites to be used for updating 3D virtual scenes in real-time for providing vital collision avoidance warnings to equipment operators.

Aug 1, 2013

By Thom Mambe, Angelo Fernando

The objective of this work was to identify key parameters related to the reduction of the sulphur content in ammonium diuranate (ADU), and the identification of solid products being formed under various operating conditions. A laboratory-scale, continuous ADU precipitation circuit was assembled using a glass reactor vessel immersed in a temperature-controlled water bath. A pre-prepared uranium feed solution was fed continuously using a peristaltic pump. Anhydrous ammonia mixed with compressed air was metered and pumped using a double-headed peristaltic pump. An over-head mixer was used to keep the solids in suspension. The precipitated ADU slurry was removed from the reactor at the same flow rate as the feed solution. The slurry was sampled to generate ADU solids for chemical and physical analysis after four hours of continuous operation to ensure steady-state conditions. The following variables were studied to determine their influence on the sulphur content in the resulting ADU. (a) sulphate:uranium molar ratio in the reactor (1:1, 1:5, 1:10 and 1:20) (b) precipitation pH ( pH 6, 6.5, 6.9, 7.5 and 9) and (c) precipitation temperature (40C and 60C) A total of 18 tests covering the above parameters were conducted, and the results indicated that the sulphur content in the resulting solids was highly dependent on the reaction pH. Out of the pH levels tested, tests completed at pH 6.9 and 7.5 generated solids containing the lowest sulphur contents, between 0.5 to 1.5% S uranium basis (UB). The sulphur content in solids was found to vary linearly with the sulphate:uranium ratio in the feed solution, showing a statistically valid correlation. The impact of temperature was minor between 40°C and 60°C, with a slight advantage at higher temperatures. Tests at a sulphate:uranium ratio of 1:1 produced solids with the lowest sulphur contents. The influence of pH or temperature on sulphur content in solids was almost non-existent at this sulphate:uranium ratio. Precipitation pH is the major factor influencing ADU sulphur content, followed by the uranium to sulphate ratio.

Jan 1, 2020

By G. Deschênes

Located in North West Tanzania, Buzwagi is an underground narrow-vein gold mine owned by Barrick Gold. The plant was commissioned in 2000. The reserves are estimated to be more than 25 years. The ore, containing gold, silver and copper mineralization in sulphides, is processed at 3,300 tpd. This paper presents the results of an investigation to determine the performance of an ammonia-cyanide leaching approach to recover gold from two samples. Coarse gold was recovered by gravity prior to leaching. The gravity tailings had the following composition; 1.97 g/t Au and 0.31% copper for the medium cyanide soluble copper (MCSC) sample and 2.80 g/t Au and 0.53% Cu for the high cyanide soluble copper (HCSC) sample. Experiments were conducted for 72 hours in stirred tank reactors with monitoring and control of parameters. The straight cyanidation produced gold extractions of 76.1% for the MCSC sample and 84.6% for the HCSC sample. Associated cyanide additions were 6.1 kg/t and 11.5 kg/t respectively. The gold extraction of the MCSC sample was improved to 88.8% using 350 ppm NaCN and 700 ppm ammonia. The associated cyanide and ammonia additions were 2.5 kg/t and 1.7 kg/t respectively. For the HCSC sample, 82.5% gold extraction was obtained using 500 ppm NaCN and 600 ppm ammonia. The cyanide addition and ammonia additions were reduced to 3.8 kg/t and 1.0 kg/t respectively. No significant decrease in gold extraction was noticed when the cyanide and ammonia were reduced to 150 ppm and 500 ppm respectively. In the presence of ammonia, a significant amount of cyanide was oxidized to cyanate by the cupric ion. In the absence of ammonia, the formation of copper cyanide was the predominant reaction responsible for consumption of cyanide.

Jan 1, 2012

By W. L. Murphy

The Star Lake property, located 115 km northeast of La Ronge, Saskatchewan is underlain by metamorphosed andesitic tuffs and flows which have been intruded by the dioritic to granitic Star Lake Pluton. Gold mineralization on the Star Lake property was first discovered at Ru h Lake by E. Beveridge in 1959 and by M. and E. Hird in 1961. In 1960 E. Partridge discovered Kahn 18 and Kahn 28. In 1982 the SMDC-Starrex joint venture completed geophysical and geochemical urveys including magnetics, VLF, IP/Resistivity, vegetation, bulk till and oil sampling, followed by drill testing of pecific targets. To date the most ignificant depo it is the 21 Zone which contain drill indicated reserves of 230,000 tons grading 0.5 oz/ton Au . The 21 Zone con ists of quartz with 5-10% (locally > 30%) drusy pyrite, minor chalcopyrite and trace amounts of scheelite, chalcocite and arsenopyrite. The 21 Zone is enclosed by a 25-50 m wide band of mylonitized monzonite. The mylonite occurs in the central portion of a 300 m wide northeasterly trending zone of brittle deformation .

Jan 1, 1986

By Chris M. Healey

"Abstract - Perhaps the single most significant variable in the evaluation of a mining project is the reserve estimate. Many parameters are considered when estimating reserves, among them geology. This paper examines the link between the quality of a reserve estimate and a good understanding of the geological controls for the deposit. A clear understanding of the geometry is essential to the accurate definition of the shape and size of the deposit. This includes the definition of any structural controls as well as the proper interpretation of the stratigraphy. Further when the distribution of grades is erratic and there is consequently a high nugget effect, there are significant problems in estimating the true grade of the deposit.Two Saskatchewan examples are presented, one with good knowledge of the controls and therefore good estimates of reserves, and the other with a poor understanding of the geology and resultant problems in deriving good estimates. In both cases the reserve estimates at various stages in the project development are compared to actual results from underground work. The first example is the Star Lake Mine where just about all the estimates were within 10% of the actual on both tonnage and grade. The Laurel Lake deposit is discussed to show how problems in interpreting the geological data make reserve estimation very difficult. Laurel Lake has the additional problem of erratic grade distribution."

Jan 1, 1992

By V. Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modelling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioning of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

Apr 1, 2004

By D. Ling, Santos. R. M., T. Van Gerven, M. Guo

The valorization of alkaline waste materials from thermal processes utilizing intensified mineral carbonation routes is investigated. The principal advantages of this approach are the chemical stability and storage safety of mineral carbonates, the opportunities for process integration presented by the technology, and the potential for conversion of low-value materials into useful products. Treatment and disposal of steel slags are a costly burden on steel plants. Sustainable solutions for Argon Oxygen Decarbonisation (AOD) and Continuous Casting (CC) stainless steel slags and Basic Oxygen Furnace (BOF) steel slag are desired. An integrated on-site mineral carbonation approach is envisaged as a favourable solution.

Jan 1, 2011

By J. E. Armstrong

"IntroductionT'HE PRODUCTION of gravel and sand may be considered to be the major mining operation in the Lower Fraser Valley of British Columbia. At least thirty pits are in operation with a yearly production probably in excess of two million yards and a value in excess of one million five hundred thousand dollars before crushing, washing, and sizing. The value of the finished products would probably be double the above figure.Since 1949, the writer and his co-workers have been engaged in the geological investigation of the Lower Fraser valley and adjoining Coast mountains for the Geological Survey of Canada. The study, which is not yet completed, includes both bed-rock geology and geology of the unconsolidated sediments lying above bed-rock. In a rapidly expanding industrial area, .an advance knowledge of the geology may• greatly aid in future 'planning, and in many cases may .prevent not only the wastage of large sums of money, 'but possible disaster. Some of the present and future applications in which geological information in the Lower Fraser valley should be of value are as follows: the development of domestic, irrigation, industrial, and municipal groundwater supplies; drainage for industrial sites,, roadbeds, and farmlands; flood control along the Fraser river and smaller streams in the area; the location of dam sites, of major tunnels for water supply •and sewage, of road-beds, of foundation sites for large buildings .and other engineering undertakings in which geology may aid; the evaluation of oil and gas •possibilities; the production of building stone; and the production of sand and gravel, the subject with which this paper is primarily concerned."

Jan 1, 1953

By L. Xia, B. Hart, G. Gingras, M. Furlotte

Plant and laboratory test work was performed in order to optimize a copper/zinc flotation separation circuit at Matagami concentrator, Canada. The testing identified a significant difference between the laboratory testing and the plant flotation, particularly for the sphalerite recovery in the rougher copper concentrate. Tests indicate that sphalerite recovery of the flotation concentrate in the laboratory testing was significantly higher than in the plant. The ToF-SIMS surface analysis identifies surface species responsible for the discrepancy in Zn recovery. It shows that sphalerite flotation is in response to the collector attachment and a significant enrichment of Cu on the surface of sphalerite grains. A comparative surface chemical analysis was performed on both sphalerite and chalcopyrite grains from the plant flotation and laboratory testing in order to identify surface species variability between the two testing. Two significant observations were revealed. First, there is considerably more hydrophilic iron oxyhydroxide on sphalerite surface from the plant flotation sample relative to those from the lab testing. The secondary coating likely completely or partially passivates sphalerite surfaces, reducing Cu enrichment and hence sphalerite floatability. Secondly, comparing the surface chemistry on sphalerite and chalcopyrite, the hydrophilic iron oxyhydroxide species have preference for the sphalerite grains relative to chalcopyrite. Despite numerous studies on the effect of galvanic coupling during grinding, there is limited documented evidence on the effect of the milling environment on the flotation and plant operations. This observation suggests that interaction between sulphide minerals and grinding media have a significant influence on subsequent flotation. This paper discusses the results of a detailed surface chemical evaluation of sphalerite grains from both the plant and laboratory testing in the context of grinding environments and pulp chemistry.

Jan 1, 2016

By Roland B. Hoag, Roger G. Webber

Sulphate concentration in groundwater is a good measure of the extent of oxidation of sulphides, provided that sulphide minerals are the primary source of the sulphate. A study was conducted near the Eustis Mine in Quebec to determine where and how the sulphate in groundwaters originated. Atmospheric precipitation is the only source of sulphate other than oxidation of sulphides, and in this study area it is equal to 0.01,. millimole per litre. The oxidation of sulphides can be divided into subsurface oxidation (mainly inorganic processes) and surface oxidation (including both organic and inorganic processes) . The maximum sulphate concentration due to subsurface oxidation of sulphides depends on the solubility of 0 2 in water and is 0.25 millimole per litre. Surface oxidation is, therefore, responsible for any amount greater than atmospheric plus subsurface contributions (0.29 millimole per litre). Surface inorganic oxidation occurs in waters with a pH greater than 15 and is controlled by the kinetics of the oxidation processes. Organic (bacterial) surface oxidation is dominant only in acid (pH< 1.5) waters. The bacterial action accelerates the oxidation of sulphides, and large quanttties of sulphate may be introduced into solution.

Jan 1, 1976

By C. R. Larsen, R. G. Bradburn, A. L. Mular, B. C. Flintoff

"Following the acquisition of grinding- circuit data at Brenda Mines Limited for simulation purposes, various methods to mass balance the circuit were evaluated. Unfortunately, different answers were obtained for different balancing methods. A data-adjustment procedure was therefore developed. The procedure assumes that all ""best-fit"" criterion. A search is conducted with the minimum set of water masses and narrow size ranges of solids around the circuit (called search variables), which permit the computation of any of the measured data points. Search variables are used to calculate measured values for an objective function of the form: [ ] where W, is a weighting factor•, M1 is a measured value and M. is a corresponding . value calculated from search vanables. The best values of M, are those which minimize R. The above method is compared with others that have been utilized for mass balancing circuits."

Jan 1, 1976

By N. A. Beier, N. Slingerland

"Oil sands tailings impoundments rank among the largest (spatially) in the world, covering a total of approximately 220 km2 of northern Alberta, Canada. A preliminary geomorphic design for an oil sands tailings storage facility (TSF) landform was completed with the goal of eventual closure and delicensing in mind. This paper outlines methods identified during the design process that streamline closure when implemented early in the mine planning and TSF design stages. With most oil sands TSFs currently in active operation (and some still in the planning stages), geotechnical engineers and mine planners have the opportunity to make operational and design decisions, such as those outlined herein, that are likely to improve the geotechnical and environmental performance of the landform post closure. ¦ KEYWORDS Alberta, Athabasca oil sands (AOS), Landform design, Reclamation, Sand dam, Tailings storage facility (TSF) RÉSUMÉ Les bassins d’accumulation des résidus issus des sables bitumineux font partie des plus grands (en termes d’espace) au monde, et couvrent au total environ 220 km2 dans le nord de l’Alberta, au Canada. Une conception géomorphologique préliminaire a été réalisée pour le modelé d’une installa¬tion de stockage des résidus (ISR) issus des sables bitumineux en gardant à l’esprit la fermeture et le retrait de permis à terme. Cet article présente les méthodes identifiées pendant le processus de conception qui simplifient la fermeture lorsqu’elles sont mises en oeuvre dès les premières étapes de planification de la mine et de conception de l’ISR. La plupart des ISR issus des sables bitumineux se trouvent dans des exploitations actives (dont certaines en sont encore aux étapes de planification), aussi les ingénieurs géo¬techniques et les planificateurs miniers ont la possibilité de prendre des décisions en termes d’exploita¬tion et de conception, telles que celles présentées ici, qui pourraient améliorer la performance géotechnique et environnementale de la phase suivant la fermeture du modelé. ¦ MOTS CLÉS Alberta, assainissement, barrage de sable, conception du modelé, installation de stockage des résidus (ISR), sables bitumineux de l’Athabasca (SBA)INTRODUCTION The Athabasca oil sands (AOS) underlie 140,200 km2 of land in northeastern Alberta, Canada. Oil sands located within 100 m of the original surface account for 4,800 km2 of the total area and are considered to be economically mineable (Figure 1; ERCB, 2009). Bitumen, the thick, tar-like substance contained in the AOS, is extracted through open-pit mining and in-situ methods. During mining, the overburden is first removed as waste and the sandy, bitumi¬nous ore (“oil sand”) is transported to processing facilities via conveyor belts and 400 t trucks. Warm and hot water, as well as process aides such as caustic soda, are mixed with the oil sand, creating a slurry from which bitumen is mobilized and extracted. The resulting slurry waste product is called “tailings” and contains mineral solids, process water, and small proportions of unrecovered bitumen (Masliyah, Zhou, Xu, Czarnecki, & Hamza, 2004; Sobkowicz & Morgenstern, 2009)."

Jan 1, 2019

By A. C. Elliott, A. J. Lafreniere

THE Hamilton Works of The Steel Company of Canada is a fully integrated steel plant with an annual capacity of three million tons. Located on the south shore of -Hamilton bay, it is in the centre of Hamilton's industrial belt. The heavy concentration of industrial activities found in this area, accompanied metallurgical well-known sources of pollution which are normal to urban areas is creating a pollution problem which concerns both industry and the general public. The Steel Company of Canada has recognized this problem and, accordingly, has adopted the policy of integrating suitable pollution control devices into its new installations. Much effort is also being expended to control the emissions of air contaminants from the existing equipment. At the Hamilton Works, there are two main sources of metallurgical dust emissions to the atmosphere -the Open Hearth furnaces and the Sinter Plant. Of these two, the Open Hearth furnaces are, undoubtedly, the largest single source of

Jan 1, 1962

By R. A. Price

The base of the biozone of Olenellus is accepted as the most universally applicable criterion for defining the base of the Cambrian System. The use of this definitive criterion is restricted by important practical considerations. In the southeastern Canadian Cordillera this zone appears to truncate the basal ortho-quartzite of a west to east marine -transgression. This transgression began in Interior British Columbia in the Late Proterozoic and terminated in the region of the present Rockies in the Late Waucobian. Most of the material deposited by the transgressing sea originated in the eastern positive element &apos;Laurentia&apos; and was transported over the intervening low Proterozoic-Windermere erosion surface. The configuration of the advancing shoreline and the distribution of the sediments were controlled by the tectonic activity of positive elements in northwestern Montana (Montania) and in the Fairmont Hot Springs-Radium area of British Columbia.

Jan 1, 1956

By R. Pandher, R. Schonewille, N. Tripathi

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGE TM METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel&apos;s Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By R. Pandher, R. Schonewille

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGETH METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel&apos;s Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By J. G. A. Stevenson

"IntroductionDURING the past quarter of a century diamond drilling, in all its phases, has increased in Canada to a very impressive total of more than 10,000,000 feet annually. Since the art of diamond drilling became recognized, some seventy-five years ago, there has been considerable improvement in both equipment and technique. The steam-powered drill rig and the hand-set diamond bit are things of the past.The purpose of this paper is to review some drilling trends •and practices over the past few years. In the preparation of the paper, the author wishes to acknowledge kind assistance of Mr. J. D. Cumming, Dr. C. H. Hitchcock, Mr. Robert H. Quintal, and many others, including staff members of the Longyear organization.Figures provided by the Dominion Bureau of Statistics for the year 1954 show that Canadian production of metallic and non-metallic minerals and structural materials had a value of $1,454.2 million, excluding radioactive products for which figures are not available. Approximately 61 per cent of this valuation comprised production of nickel, copper, gold, coal, asbestos, zinc, lead, and iron. It is certain that diamond drilling played a major role in the discovery and development of the orebodies from which these minerals were obtained.After the surface examination of an ore deposit, diamond drilling will automatically follow, in order to determine structure, grade, and tonnage.Footage drilled by mining companies and contractors on mineral exploration and blast-hole work since 1945, as reported by the Do-minion Bureau of Statistics, is shown in Figure 1."

Jan 1, 1955

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to maximise health and safety performance in the mining industry through implementing continual improvement in management of major unwanted events. A comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This will be extended to outburst, coal burst and bumps, interface displays and controls, tailings dams and inrush in 2013. RISKGATE presents substantive and leading edge controls to assist industry stakeholders in the design, management and reporting of organisational and regulatory compliance requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry. All major Australian mining companies are contributing topic experts to this broad industry initiative. In the first 24 months, nine coal mining companies nominated over 80 different experts who contributed over 400 days of individual time to the knowledge capture workshops. RISKGATE is the largest single Australian Coal Association Research Program (ACARP) occupational health and safety (OHS) initiative to date.

Aug 1, 2013

By Barry J. Turley

With over 700 large electric-drive haulage trucks operating in Canadian mining today and over 3700 in mines worldwide, most aspects of electric drive are well known. Recently, however, extensive application of these trucks to down-hill hauling in mountain mining makes it vitally important that many of us better understand the operation and proper application of the dynamic retarding feature of these vehicles. This paper is an attempt to clear up misunderstandings on this subject, to suggest precautions that mining operators should take in comparing competitive retarding systems and to challenge equipment manufacturers to evolve improvements to the important aspect of system performance.

Jan 1, 1978