Search Documents

By F. A. Auld

"During the period 1958-1980 seven deep shafts were sunk from the surface in the UK. From 1977 until 1989 sixteen deep shafts were sunk in the UK, all concrete lined. Subsequently from 1989 up to the present day no deep shafts have been sunk in the UK, a period of 30 years. Developments in the design and construction of deep shaft linings in the UK therefore were predominantly carried out throughout the period 1977–1989. This knowledge is recorded in several published papers by the author over that period which will be referred to in the paper. INTRODUCTION The paper includes a review of past precedent for the design of deep shaft concrete linings in the UK and sets out the principles for future designs, including the design load to be adopted and Factors of Safety (SFs) to be used in the design. Hydrostatic pressure increases with depth from the surface and therefore the concrete lining must increase in thickness and strength throughout its depth to resist the pressure. High strength concrete mixes were developed to enable economic linings to reach greater depths and these will be detailed. The ground conditions to sink through in the UK consist of predominantly competent (self-standing when excavated) rock, which can be water bearing, and hence a hydrostatic pressure resisting lining is required. The paper describes the construction measures needed to produce a dry shaft by way of pour length, joint detail, backwall grouting and joint sealing details. PAST PRECEDENT FOR UK DEEP SHAFT SINKING AND LINING Seven deep shafts were sunk from the surface in the UK from 1957–1977 over a 20-year period (Auld, 1987). These are listed in Table 1. Three shafts were for British Coal, two were for Cleveland Potash Ltd and two were for the Central Electricity Generating Board. The British Coal shafts were 5.486 m and 7.315 m internal diameter to depths of 550 m and 780 m, respectively. At 5.5 m internal diameter and a depth of 1150 m, the two Boulby Mine shafts for Cleveland Potash Ltd are currently the deepest shafts in the UK. The two Central Electricity Generating Board shafts of 5 m and 10 m internal diameter, to depths of 255 m and 440 m, respectively, were ventilation shafts for a pumped storage scheme. Six of the shafts were sunk by Thyssen (GB) Ltd and one by Cementation Mining Ltd."

Jan 1, 2019

By D. G. Sinclair

In any discussion on the subject of mine-safety, it is well to honestly face the fact at the outset that mining is a hazardous occupation and that certain inherent dangers attach to the work, which, in spite of the greatest vigilance on the part of everyone concerned, will from time to time exact their toll of in jury or death from the underground worker. Great progress has been made of late years in narrowing down the range of these necessary risks, and, illustrative of what can be done along these lines by concerted effort, it is pleasing to read from time to time of large operating mines running for weeks, months, a year or more, without a single lost-time accident. To achieve any results in the work of accident prevention it is necessary, first, to have a definite goal, such as a no-accident period, be it a week, a month, or a year, to aim at; and, second, to set up definite standards to work by. The legal code of regulations should form the basis of all standards of work at every mine and should, for this reason, cover as far as possible all conceivable phases of operation. This represents the ideal, but in practice it is unattainable, largely because of the many variables that must be considered, due to the divergence in the scale of operations and to differing geological conditions at the different mines. Hence it becomes necessary for the operator who wishes to attain the maximum in the establishment of high standards of safe operation to so amplify the code as to meet the peculiar requirements of his operation.

Jan 1, 1930

By Ralph V. Stewart

"The asbestos orebody is contained within ultrabasic rocks of Precambrian age, being located in the continuous permafrost zone of the Quebec Ungava Peninsula, some 300 miles north of the tree line at approximate latitude 61'49' and longitude 73°58'.The asbestos deposit is at the western tip of a folded ultrabasic sill complex which trends northeast and covers an elliptical area 4.5 miles wide by 15 miles long. Locally. the asbestos occurs in. a completely serpentinized dunite rock. The principal rock types in the vicinity of the ore-body originally consisted of dunite, peridotite and pyroxenite, all of which have experienced at least two periods of alteration, so that no fresh rock now remains.The main ore zone in the open pit is approximately one quarter mile in length, 150 to 200 feet in width, and plunges at 25 to 30 degrees in a northeast direction below surface, to a vertical depth of at least 1,200 feet, Consider¬able tectonic activity resulted in favourable structural conditions which culminated in the formation of the ore zone in its present form.The deposit consists principally of cross-fibre ""gash type"" veins which vary in length from several inches to several feet. The principal fibre vein direction is parallel to the dip of the enclosing serpentinized dunite and sill complex.Some of the problems encountered during diamond drill¬ing in permafrost are briefly discussed."

Jan 1, 1976

By J. Gao, H. O. Gekonde, S. V. Subramanian

"The functional role of inclusions at low cutting speeds is to promote ductile fracture in chip formation process, whereas the role of inclusions at high cutting speeds is to prevent tool crater wear by suppressing the tribological phenomenon of seizure at the tool-chip interface. Glassy oxide inclusions are engineered into the workpiece to form a viscous layer in-situ at the tool-chip interface at high cutting speeds. The viscous layer lubricates the tool-chip interface to prevent the seizure. In comparison with the large volume fraction of inclusions needed for promoting ductile fracture at low cutting speeds, the amount of inclusions required for lubricating the toolchip interface at high cutting speeds is very small and is in the range that is typical of clean steels. The chip fracture process at high cutting speeds is aided by strain rate hardening of the matrix, which facilitates chip disposal of relatively clean steel.Inclusion engineering for high speed machining involves the control of the rheology and composition of inclusions to meet target viscosity at the tool-chip interface. The application of thermodynamic models in controlled production of inclusions in steels designed for high speed machining is discussed."

Jan 1, 1998

By B. A. Monkman

"IntroductionONE OF :THE most effective methods by which the construction industry is combatting mounting building costs is by making increased use of lightweight materials, thus reducing the dead load to be carried •by structures. This applies to non-metallic materials as well as to metallic ones, and particular attention has been given to developing lightweight aggregates for use in concrete.The use of lightweight aggregates is not new and, in fact, dates back to the Roman Empire, when pumice was used in the walls and domes of the Roman buildings. More recently, and up to a decade or so ago, the demand for these aggregates was met from deposits of volcanic cinders, pumice, scoria, etc., and from the by-products of blast furnaces and coal burning boilers. However, these sources of supply are no longer sufficient to meet the demand, for transportation costs pretty well restrict the use of the natural lightweight aggregates to the western cordillera regions where the deposits of these materials occur, and the use of expanded slag aggregates to the areas neighbouring the plants where slags are produced. As for cinders, the supply has been greatly reduced by the conversion of industry to fuel oil, natural gas, and powdered coal, and the large stockpiles which existed previously have been pretty well exhausted.Industry's approach to the problem of a decreasing supply, in the face of an increasing demand, has been characteristically direct. The solution has been to construct plants whose sole .purpose is to produce economically an acceptable light-weight aggregate from materials close at hand."

Jan 1, 1955

By Raju S. Sagi

This paper deals primarily with the different types of drilling methods used by the Iron. Ore Company of Canada for sampling the soft and friable hematite-limonite (secondary) iron ore deposits found in the Scheferville area. The problems associated with drilling, sampling, sample handling and sample preparation. for chemical analysis of these ores are discussed. Systematic evaluation of the various drilling methods led to the selection of an integrated drilling system. This system consists of a rotary dual- tube - reverse-circulation drill, with tricone bit, polymer mud and mechanical sample splitter, The historic al development of this drilling system is described in detail, as are the equipment , sample flow and quality control checks carried out to obtain representative samples. This integrated drilling and sampling system has been used satisfactorily on a routine basis for determining the grade and tonnage of ore for the various deposits for the last five years (1972-76) in the Schefferville area.

Jan 1, 1977

By M. Uszko

The climatic area in which Poland is located requires heating the ventilation air at intake shafts during the winter season. Air heating of the intake shaft should ensure safe operation of hoisting devices; while at the same time it also affects the conditions of the mine environment. The paper presents the issues of shaft heating in coal mines in terms of the mining law, the effect on the conditions of the mine environment and heating technology solutions used in the mines of Kompania Weglowa S.A. (KWSA).

Aug 1, 2013

By James Dickson

Brief History of Discovery and Early Development In the first half of the nineteenth century, the only authority on the Pacific coast between the Columbia river and Alaska was exercised by the Hudson's Bay Company, who had established a series of forts and trading stations on the coast from the Columbia north to Millbank sound. The Hudson's Bay Company were chiefly interested in the fur industry, and the large influx of settlers from the eastern United States into the territory now known as the States of Oregon and Washington, about 1840, not only interfered with the fur business but involved the question whether the territory should be under the British or the American flag. Anticipating the possibility, later realized, of losing control of this area, the Company, in 1845, established their main fort and trading centre on the southern end of Vancouver island under the name of Fort Camosun; shortly afterwards changing the name to Fort Victoria. Realizing that their former policy of discouraging all attempts to develop any other business than the fur industry had lost them several hundred thousand square miles, the Hudson's Bay Company now set about encouraging settlers in the vicinity of Fort Victoria by disposing of lands to suitable parties and also to those in the employ of the Company. The usual pioneering stage was passed through with the starting of small sawmills, grain mills, etc., and the incidental work accompanying such efforts. Any coal required for blacksmithing or other purposes was brought from England around Cape Horn by the few ships that visited the Pacific Coast. About 1849, an Indian who was having his gun repaired by a blacksmith in Fort Victoria asked about the "black stones" used in the fire and, on being told that the "black stones" had to be brought a great distance, he informed the blacksmith that there was plenty of the same stone where his people lived. This information was immediately given to an official of the Hudson's Bay Company who talked with the Indian and told him that if he would bring some of the "black stones" he would get his gun repaired free and a present of a bottle of rum. Nothing more was heard of this coal until April of the following year, when the Indian came into Fort Victoria with his canoe loaded with coal, which was tested and found to be of good quality. It is reported that the Indian got his bottle of rum.

Jan 1, 1935

By M. Dupuis

It has been previously demonstrated [1,2] that using selective collector bar rodding has a big impact on the uniformity of the current density at the top surface of the cathode block and hence on the intensity of the horizontal current in the metal pad, The present study investigates the impact of using selective collector bar rodding on the MHD stability of a 500 kA aluminium electrolysis cell, For this purpose the recently developed MHD package for the aluminium reduction cell time dependent behavior is used.

Jan 1, 2005

By R. R. Dickson

Princess colliery, the largest mine operated by the Old Sydney Collieries, Limited, commenced operations in 1877. It was the first mine sunk in the Sydney coal field with the primary object of working submarine coal. Until 1925, coal was won by the room-and-pillar system. By that year, the depth of cover over the workings was 1,300 feet, and physical conditions had become such that it was impossible to extract completely the pillars formed by the working of the rooms. Because of this, the system of work was changed to longwall in the early part of that year. At first, an orthodox hand-pick method was used, with gate roads laid off at 50-foot centres and the mine cars loaded by hand directly on the longwall faces. Later in the year, the first machine-cut conveyor longwall faces were started.

Jan 1, 1946

By B. R. MacKay

Introduction During the past six seasons the writer has been engaged in semi-detailed investigations on the coal areas lying along the front of the Rocky mountains between the Brazeau river and the Smoky River Coal Reserve (see Map, Figure 1). The purpose of this paper is to present some observations pertaining to the stratigraphy and structure of the district, touching especially upon the lithological units into which the Lower Cretaceous sediments have been divided, the thicknesses of the formations at different localities, the number, thicknesses and horizons of the principal coal seams, and the structural conditions which exist in the various fields.

Jan 1, 1930

By G. Beckstead, L. F. Sawatsky, R. Nutbrown, D. Long, G. Gould

"This paper presents a case study for optimizing water management at Gregg River Coal Mine located near Hinton, Alberta. The optimization study was derived based on a review and assessment of existing management practices and plans for future operation and final reclamation. A proactive water management strategy was developed to assist mine staff in adopting a rational, environmentally sound, and economical approach to water management. A plan was developed to provide for safe operation, self-sustaining operation, low maintenance, minimum negative environmental impacts, and anticipation of future needs for existing and future operations. A plan for final reclamation drainage was developed including establishment of effective, sustainable, and maintenance-free water management systems. The study demonstrated the importance and benefits of a proactive approach for integrated mine water management. This approach is recommended for other similar mine operations because it will improve environmental compliance and reduce costs of water management. IntroductionGregg River Resources Ltd. (GRRL) operates an open pit coal mine on the eastern slopes of the Rocky Mountains, located about 45 km south of Hinton, Alberta. GRRL opened the mine in 1982 and expects to continue operations after Year 2000. GRRL has progressively reclaimed the disturbed area and expects to complete mine-land reclamation shortly after mining in the area is complete. The existing disturbed area and reclaimed area covers approximately 9.5 km2 and will expand to about 10.5 km2 upon mine closure.Like other coal mines in the mountainous areas of Alberta and British Columbia, the GRRL coal mine is subject to highly variable temperatures and moisture conditions. Average monthly precipitation varies from a low of 12.6 mm in January to a high of 113.0 mm in August, based on the precipitation record at the mine site since 1982. Despite the relatively high rainfall during the spring and summer months, excess water problems during rainfall events are quickly replaced by water deficit conditions during periodic droughts. Surface runoff varies from near zero in the winter to a mean annual monthly maximum of 78 mm during the month of June. The mean annual surface water yield is 345 mm."

Jan 1, 1997

By C. A. Ingram

The Cigar Lake ore body is a high-grade uranium deposit situated within water-saturated sandstone. In order to extract the uranium ore remotely, ensuring minimal radiation dose to workers, and also to access the ore from stable ground, the Jet Boring System (JBS) was developed. This method of mining involves drilling a pilot hole up through a frozen ore body and utilizing a high-powered water jet to mine out cavities. During the mining process an ultrasonic sensor will be used to provide feedback to the operator, who is located beneath the ore body, as to the dimensions of the cavity. However, more precise data is required to determine final shape, volume, and location of the cavity for mine planning purposes. Selecting a device that will provide sufficient range data in the challenging environment will be vital to optimizing the mining process. Major issues include fog build up and flying debris during mining, and an environment that is wet, dark, and cold A test cavity has been designed and constructed at the Saskatchewan Research Council (SRC) so that a study comparing three different technologies, as prospective candidates for the survey system, can be conducted. The devices being evaluated include a Senix ultrasonic sensor, an MDL Cavity Auto-Scanning Laser System (C-ALS), and a MESA Time of Flight (ToF) camera. The ultrasonic sensor is known to provide range data in foggy conditions but has low accuracy. The C-ALS has been developed for surveying remote cavities but is expensive and does not provide reliable data in fog. The ToF camera provides a high volume of data in a short time period, with potential to provide accurate information in extreme conditions, but has not been tested in a mine cavity application. Iterative closest point (ICP) registration is applied in an attempt to create a 3D point cloud from the scan data and to also compute rotation and translation of the ToF camera. This paper presents an overview of the challenges involved in conducting a survey within a JBS mined cavity, the analysis used to determine the suitability of each device, and the data collected from the test cavity.

Aug 1, 2013

By P. O. Sandstrom

"Atlas Copco is introducing a new patented method for full-face boring. This paper presents the basic principles of the boring action and discusses the present experience regarding performance and costs. The Atlas Copco ""Full-facers"" are designed for hard-rock applications, although they are successfully boring in soft ground without major changes. The unique patented boring principle referred to as the 'Undercutting Method' permits these machines to bore, economically, in harder ground than machines based on the 'crushing principle'. This is mainly due to considerably lower cutting-tool costs, as the tungsten carbide tips only are in contact with one-third of the bored volume. The remaining rock is 'undercut' and peels off from a slight back pressure.The undercutting method also permits boring of non-circular headings and Atlas Copco has already manufactured two machines for rectangular drifts. This concept could revolutionize development work in mines employing trackless equipment."

Jan 1, 1971

By T. G. Carter

"Tremendous progress has been made in recent years towards developing computational tools that allow ready solution of most common rock engineering problems, with amongst the most advanced of the tools focusing on evaluating engineered openings within Synthetic Rock Masses. These new codes have the potential to allow much more realistic design, but they must not be used without careful calibration – prior to – during and – post completion of any modelling. This paper explores some of the pitfalls of inadequate data collection and suggests more emphasis be given to calibration. Guidelines for minimum levels of parameter data are suggested for improving application of basic to sophisticated modelling codes.INTRODUCTION & BACKGROUNDTremendous progress has been made in recent years towards developing computational tools that allow ready solution of most common rock engineering problems. The degree of sophistication now possible with some of the available codes allows one to tackle extremely complex problems that were not thought tractable even a decade ago. Indeed, generation of synthetic numerical rock masses, based on discrete fracture network representations that closely mimic actual rock mass conditions, such as are shown in Figure 1, is today relatively straightforward, and not as user-challenging as employing state-of-the-art codes of even a few decades ago. This is largely because major improvements in computer graphics and in availability of ready-made user-friendly input-output interfaces have paralleled development of these new codes, now in some cases outpacing actual new analytical/procedure developments. This is something of a reversal from the first few decades of DOS-based rock engineering computational experience, when only rudimentary graphics were available and user-friendly input-output interfaces were virtually non-existent."

Jan 1, 2015

By M. A. F. Fedikow, D. A. Baldwin, C. Taylor

The Agassiz Metallotect and the Johnson Shear Zone represent two metallogenetic fea tures located within the northern and outhern belts, respectively. of the Aphebian-aged Lynn Lake greenstone belt in northern Manitoba . Numerous gold occu rrences are associated with these two regional features . The tratabound Agas iz Au-Ag deposit with 2.9 million tonnes of 5.2 g/tonne Au and 11.8 g/tonne Ag. occurs within the Agassiz Metallotect. The stratigraphic sequence characterizing the Agassiz Metallotect comprises interlayered ox ide. silicate and sulphide facies iron formations, biotite-rich and siliceous siltstones. and a high Mg- i-Cr basaltic rock that ha previou ly been identified as tholei itic picrite. These rocks can be traced in outcrop and by their INPUT and gradiometric signature for 65 km. The Johnson Shear Zone is an ill-defined 35 km long zone of strucwral disruption that crosscuts volcanic. sedimentary and intrusive rocks and contains numerous vein-type gold occurrences. Both of these metallotects are characterized by their low level of exploration activity and as a result offer excellent residual exploration potential. Rock, basal till and vegetation geochemical techniques applied in the vicinity of the Agassiz deposit indicate the presence of trace element dispersion halos associated with the mineralization. The halos define an exploration target larger than the mineralized zone. Gold occurrences within the two metallotects are described with emphasis on the Agassiz Au-Ag deposit . A wide range of gold occurrence-types is documented including syngencticstratabound , epigenetic-replacement and epigenetic-quartz vein .

Jan 1, 1986

By M. Gagné, F. E. Goodwin

The mining industry represents a significant investment in infrastructure of which steel plays a key role. Many structures in a mine are made of steel including shaft structures (buntons, station steelwork and headgear); stope structures (roof supports, pipe hangers); haulageway structures (ore transfer stations, electrical stubbies); and surface structures (plant buildings, tank supports, pipe gantries, conveyor belts, stacks, stockpile structures, stairways and railings). Maintenance of structural components can often be difficult because of the environment, including those where corrosive fumes persist, or limited access, such as in shafts where access is limited, or to short maintenance shifts or where limited working space is available. Thus a cost-efficient, long-lasting and maintenance-free protection system for steel should be specified. Galvanizing provides the required high-quality, long-term corrosion protection to steel. Galvanizing provides protection in two ways, first as a physical barrier to corrosion and secondly by means of cathodic or sacrificial protection that is unique to zinc. The dual nature of corrosion protection provided by galvanizing significantly extends the service life of steel even in the most challenging environments. The unique corrosion protection properties provided by galvanized steel will be highlighted with global mining application case studies.

Jan 1, 2015

Agenda ?Introduction ?Geology ?Mining ?Metallurgy ?Process, Layout ?Environmental Background ?Kinross Gold Corporation owns the Lobo-Marte gold property, located in Region III of northern Chile. ?The property is close to two other Kinross mines, Maricunga 50kmto the south and La Coipa 60km to the north, plus a regional office in Copiapo and district level operating synergies are expected. ?Lobo and Marte were discovered in the early 1980s and are intrusion-hosted, porphyry-type precious metal deposits, typical of the Maricunga District. ?The Marte open pit heap leach mine was in commercial production in late 1988, but was suspended in February 1992 as it did not meet forecasted production levels and recoveries. ?Kinross plans to recover ore from the Lobo and Marte deposits through an open-pit, heap leach47,000tonne per day operation.

May 1, 2010

By B. R. Conard

Copper refining at Vale Canada (previously known as Inco) has been associated with Ni production. Because Cu and Ni carry risks for adverse health endpoints through inhalation exposure, it is critical that their aerosol levels, and the metallurgical processes through which they enter the air, are understood. Because certain Ni substances have been linked to respiratory cancers, it is also important to characterize the amounts and types of Ni compounds in occupational settings. This paper describes electrorefining and electrowinning operations near Sudbury, Ontario (1930–present), and gives aerosol measurements (1978–present).

Jan 1, 2014

By M. Al-Khawaja, F. Hassani, F. Mucciardi, N. Razavinia

"In today’s economy many industries are becoming aware of the need to recover some of the waste heat they create. Industrial processes release, on a global scale, over 100 tera-Joules (i.e. 1014 J) of waste heat annually. The recovery of waste heat can lead to a reduction of greenhouse gas emissions and it can also provide a financial benefit which can be obtained by converting some of this excess heat to electricity. At McGill, a research program has been initiated so that low grade waste heat (temperature between 100ºC and 300oC) from process off-gases found in pyro-metallurgical industries is captured and concentrated by using heat pipes and then converted to electricity by a mechanical engine. This paper illustrates the 3 C’s process (capture, concentrate and convert waste heat to electricity). It also provides some preliminary experimental data. INTRODUCTIONThe problematic climate change caused by the use of fossil fuels, the rapid depletion of global reserves and the catastrophic consequences of nuclear power generation call for renewable and safe, resources of energy, for both man and the environment. Extensive researches in the production of energy from renewable sources and improvements in efficiency of current technologies can help us to reverse this trend.The greatest advantages of using renewable energies are that they don’t deplete and they also contribute to a green environment. On the other hand the disadvantage of using these resources is that the energy available from renewable sources is much less concentrated than that provided by fossil fuels and nuclear energy. This makes renewable energy less attractive for large scale industrial uses in most cases. A key target for society for the 21st century is the production of energy from renewable sources at a cost that is competitive with fossil fuels. Fossil fuels represent a concentrated form of energy; usually it is referred to as high grade energy. Nonetheless, there is a vast supply of alternative energy. The sun, wind, water and biomass were the first to be explored. While these are all valid options that warrant concerted efforts and large investments, there is another source of energy that typically is produced by manufacturing industries. This energy is often referred to as low grade waste heat. Most of this energy is simply vented to the environment through the stream of off-gases. In the future it will be necessary to capture and convert some of the low grade heat to a valuable form such as electricity if we are to improve on the efficiency of energy usage."

Jan 1, 2012