Search Documents

By J. Fox, K. Kocsis

"Planning for sustainable cooling potential requires protected space to successfully maintain chilled propylene glycol in storage until needed. Stored propylene glycol should be judiciously cared for, safely kept from the ill effects of heat, in order to remain useful for bulk air cooling. Minimizing the chilled temperature of the propylene glycol reservoir tanks means that atmospheric conditions will be monitored closely during the chilling phase. Storage facilities would maintain restricted airflow while minimizing possibilities for heat transfer during the storage phase. Sustainable cooling systems could reduce or eliminate the need for mechanical cooling if installed with favorable conditions. Storing the cooling potential from the winter months is what this new design is all about.INTRODUCTIONIn most subsurface, bulk air-cooling methods, the main source of potential cooling energy comes from cold-water applications. This paper investigates the practical use of harvested, chilled propylene glycol as the source of cooling potential. Propylene glycol is chosen as the cooling storage liquid refrigerant since its chemical make-up is intrinsically safe to fresh water supplies and will not harm underground workers should a leak occur in the closed cooling circuit. Harvesting the cold of winter is a meaningless endeavor without proper thermal planning for the storage of the cooling potential in cold refrigerant.PROPYLENE GLYCOL STORAGE RESERVOIRA new design for a closed refrigerant bulk air cooling system employing propylene glycol as the refrigerant is presented as the main design topic of this paper. Given that a deep and hot mine will need to be considered safe and productive, a cost-effective cooling system is desired in order for the mining operation to be considered sustainable. For underground mines at northern latitudes, cooling applied to fresh air is only required 3 to 4 months of the year. During winter, ambient atmospheric conditions can be harnessed and stored for use at a later time.The basis of this sustainable design uses very cold ambient air that is circulated around galvanized steel refrigerant reservoir tanks. The propylene glycol reservoir tanks are arranged in a concrete walled pit, or tank farm, excavated in bedrock. During the coldest months, the tank farm will be exposed to the open air. As the seasons change the tank farm will be covered with insulation to maintain the maximum cooling potential for use during the warmest months of the year."

Jan 1, 2019

By Thom Sedun

No sector of the mining industry is more closely tied to local communities than aggregates. Noise, dust, traffic, visuals aesthetics and environmental impacts all fall under the purview of neighbours, local governments and nongovernment organizations. It is no surprise that aggregate operations may not be welcome neighbors in many communities. In British Columbia (BC), the regulatory environment for aggregate operations includes a local component of municipal bylaws and land use-planning in addition to the usual suite of federal and provincial statutes that apply to its sister mining sectors. Additionally, under common law aggregate extraction is not considered to be a land use subject to land use zoning, and some aggregate processing activities can be regulated by zoning. Often traversing multiple local government jurisdictions, aggregate producers find themselves negotiating not only local traffic, but also a mosaic of regulatory environments. There is an opportunity in this present situation to facilitate the application of current technology and practices in the mitigation of many community and environmental concerns associated with aggregate operations. Moving a bulk commodity is a volume-based business, and operators often don?t have time for matters that don?t directly or obviously affect the bottom line. Regulatory agencies often play multiple and complex roles with respect to their industry, not the least of which is the fiduciary role. Balancing how and when to assist an industry is often a difficult decision. For the aggregate industry in BC, the Ministry of Energy and Mines saw an opportunity to assist not only aggregate operators, but also regulatory agencies, local governments, and the general public. Through investing in the Aggregate Operators Best Management Practices Handbook (handbook) project, the Ministry of Energy and Mines (MEM) believes that it will realize a return of upheld community values, enhanced environmental protection, improved regulatory compliance, reduce disputes and a stronger provincial aggregate industry. It is the intent to publish the handbook electronically through the MEM website later this year.

May 1, 2002

By T. A. Chepushtanova, I. U. Motovilov, V. A. Luganov, G. D. Guseynova

"Kazakhstan has significant reserves of oxidized nickel ore with low nickel content. Processing of such ores is effective via pyrometallurgical technologies such as smelting to ferronickel or matte with consecutive extraction of metals from melting products. There are also many options for direct hydrometallurgical processing. However, they do not provide high nickel recovery.We studied extraction of nickel and cobalt by using combined technology of low-grade ore processing from the Shevchenko Kazakhstan deposit, which includes smelting to poor matte followed by hydrometallurgical processing of the matte. The nickel content in the initial ore was 0.75–0.9%. Pyrite concentrate of Sokolov-Sarybai Kazakhstan deposit containing 0.17% cobalt and 0.06% nickel had been used as a sulphidizer at smelting.As a result of the study, we were able to extract up to 98% of the nickel and up to 80% of the available cobalt. Obtained matte contained 3.1% nickel, 0.29% cobalt, 71.6% iron and 24.3% sulfur. Matte leaching was carried out by hydrochloric acid. The iron content in the pregnant solution was 170–185 g/dm3. Nickel and cobalt precipitation from the pregnant solution was carried out by hydrogen sulfide. Initial matte or cast iron was used as neutralizers during the process. Practically complete precipitation of nickel was achieved at 3–5% excess of neutralizer at 333–343°K in 4 hours; up to 95% of cobalt precipitation was achieved in 50% excess of neutralizer at 363°K in 8 hours. The purified solution contained 200–600 mg/dm3 of nickel, 80-100 mg/dm3of cobalt and 175–185 g/dm3 of iron. The purified solution allows to obtain iron oxides by high-temperature hydrolysis, and to regenerate hydrochloric acid.As a result of non-ferrous metals precipitation we obtained sulfide concentrate with concentration of Ni up to 25% and concentration of Co up to 5.5%. The technology is recommended for semi-industrial testing."

Jan 1, 2016

By P. Tukkaraja, K. Katzenstein

"Block caving is one of the most economical and efficient underground mining methods and has gained popularity around the world especially for extracting low grade and massive ore bodies. However, during the extraction of ore from the draw bells, gases trapped inside the cave could emit into the working areas; hence, ventilation plays a key role in operating block cave mines successfully where gas emission is a concern. To design an effective ventilation system for a block caving mine, given the dynamic nature of the caving process, it is necessary to develop airflow characteristic curves (P-Q) for a given cave. This study uses a 1:100 scale physical model with an exhaust fan system, and a Computational Fluid Dynamics model of a block cave to investigate the airflow behavior through the cave filled with broken rock material. From this study, it was observed that the cave airflow resistance increases with the decrease in cave porosity and the particle size.INTRODUCTIONThe block cave mining method is gaining popularity owing to its low cost and high productivity. This study considered a case where this bulk mining method is used for the extraction of an orebody that contains uranium mineralization. During the extraction of broken ore from the draw bells, radioactive gases trapped in the cave zone could be released into the production drifts and could create unsafe working conditions in the mine. Mine ventilation systems play an important role in regulating the migration of radon in working areas. One of the strategies to control radon migration in a block cave mine is to exert negative pressure on the cave zone by using an exhaust fan above the cave zone. In order to select an appropriate exhaust fan system, it is necessary to study the airflow resistance of the cave zone (Loring & Nelson, 2006).Extraction of broken ore via drawpoints creates a void volume inside the cave called the air gap. Air gaps with larger heights can lead to air blasts in a block cave mine should the cave collapse. Besides that, the air gap can also lead to decrease in ventilation system efficiency due to recirculation of air flow and associated shock losses. Air gap height can also have a profound effect on the variation of cave airflow resistance (Erogul et al., 2015, 2017). The knowledge of cave airflow resistance is also important for predicting the intensity of an air blast. Cave airflow resistance is a function of cave properties such as broken rock size, air gap, and porosity inside the cave zone (Baysal et al., 2017). Initially, a scaled experimental model with a forcing system was developed to investigate the airflow behavior through the cave, however, this model couldn’t provide an observable change in the airflow resistance when the cave properties were changed (cave porosity, and airgap) This was attributed to the difficulties associated with forcing system in terms of achieving lower porosity values with the available material (lightweight shipping boxes) for simulating broken rock inside the cave zones, and controlling air leakage from the model (Ajitha et al., 2018)."

Jan 1, 2019

This paper focuses on the dissolution of various Manganese based compact additions into liquid Magnesium. The experimental procedure employed cylindrical compacts with various Manganese compositions. The various temperatures of the additions and the Magnesium bath were measured simultaneously during the immersion of the additions into Magnesium bath. The exothermicity level of these additions during their dissolution into liquid Magnesium was determined. The relation of the exothermicity level with the dissolution kinetics was also examined. In addition, SEM and EDX work was conducted for additions, which were withdrawn from the Magnesium bath. Finally, the recovery of these additions was estimated by taking samples from the Magnesium bath and conducting ICP analyses.

Jan 1, 2006

By T. Patching

"MINING operations at the Star Key Mine provided an example of a small-scale prairie-type coal mine that employed several interesting procedures and achieved good productivity with low capital expenditures. The mine was located about 11 miles north of the city of Edmonton, on the north side of the Sturgeon River valley. It opened in 1945 and operated until 1979. Output in the winters reached about 500 tons a day in the late 1940s, but in the spring and summer periods activity was usually limited to only servicing and development work. In the later years of the mine's life sales fell to less than 100 tons per day. Most of its output was bought for domestic use in furnaces and stoves so production of large sizes was desired. A modest market for stoker coal did exist for a time. Screenings (-5 / 8 in.) were sold to the city's power plant until it converted to natural gas and were also used for thawing frozen ground for work on pipelines. These markets were comparatively small and the small sizes did not command as high a price as did the larger sizes. However the extension of natural gas services to rural markets cut into the domestic heating market and finally led to closure of the mine. The coal was strong when freshly mined, but because of its high inherent moisture content, about 25%, it did not store well on surface but tended to disintegrate. It was of subbituminous Crank with a heating value of about 8000 Btu per pound and burned with a clean flame. The seam mined was in the Edmonton Formation, of Upper Cretaceous age, at a depth of 60 to 80 ft below the surface. The seam in the mine area was about 11 feet in thickness but thinned gradually to the north and south and split to the west (1). It was approximately horizontal but gentle rolls in the floor of several feet in height necessitated brushing in places to produce suitable haulage grades. The floor material was of bone and clay, overlying a thin layer of coal. Above the seam there were only a few feet of mudstones and weak sandy shales while the remainder of the overburden was clay and unconsolidated glacial till and surface soil. Because of the soft floor and weak roof material the miners usually left about a foot of coal in the floor to provide a firm working surface and about a foot of coal above the rooms and two feet of coal above the entries to provide a competent roof."

Jan 1, 1985

By P. Abachi

Cemented carbides or hard metals that generally consist of hard tungsten carbide and a tough metal binder such as cobalt are important in many segments of the world economy, ranging from automobile related components to machining, cutting, and drilling tools. For metal cutting operations such as turning and milling, replaceable cemented carbide inserts are frequently used. The exposure of inserts to very severe conditions (e.g. temperatures as high as 1000°C) in combination with very high loads, limits their lifetime. When the tools and components are scrapped, they are collected with a view to recovering the tungsten carbide and cobalt due to both their environmental aspects and their strategic importance. In this work, a selective electrolysis process was used for recovery of WC powder particles from cemented carbide scraps. The WC-10Co and WC-10Co-VC up to 3 wt.% VC was produced using powder metallurgy route. The mean particle size of WC, Co and VC were selected as 2.5, l.5 and 2.2 µm respectively. Referring to electrochemical curves of WC-10Co cemented carbides in hydrochloric acid solutions with different concentrations, the recovery rate was enhanced in IN acid. Therefore, this solution was selected for recycling of all samples. The surfaces of as-produced and corroded specimens were investigated using a scanning electron microscopy (SEM). Detection of corrosion products was provided by energy dispersive spectrometry (EDS). According to results, the selective electrolysis process could be useful in the recycling of scrap carbide materials, although more studies should be undertaken on economical aspects of the process and the quality of samples produced using recovered powders.

Jan 1, 2005

By D. J. MacKinnon, Kazi E. Haque

Ammonia present in a variety of mine/mill waste waters was almost completely oxidized to nitrogen by chloride mediated electro-oxidation. A closed circuit operation of preconcentration of ammonia on a suitable adsorbent (e.g. zeolite or a resin) followed by brine stripping of ammonia and electrolysis of the strip liquor seems to have sound technical, economic and environmental merits. The removal of ammonia, cyanide, cyanate or thiocyanate from a mine/mill waste water (e.g. gold mill), either individually or collectively, is also feasible by chloride mediated electro-oxidation technique. Further R&D investigations are necessary for the development of a closed circuit operation for the removal of ammonia, cyanide and thiocyanate; and also to obtain technical data for process cost estimates

Jan 1, 1996

By K. S. Coley, G. A. Irons, T. Kaneyasu

"It is very important to reveal the lime dissolution mechanism in steelmaking slag, to promote its dissolution without calcium fluoride, which is now almost forbidden for use in most industrialized countries. In this research, the purpose was focused on the development of an experimental method to measure the mutual diffusivity of Ca2+ under the condition of lime dissolution into slag. By forming diffusion couples using a ""vacuum slag aspirating technique"", the method was established. The following mutual diffusivities of Ca2+, in CaO-SiO2-FeO slag systems, imitating oxygen steelmaking slag, were determined using this method:4.1*10-10 m2/s at 1400°C for 27wt.%CaO-53wt.%SiO2-20wt.%FeO slag,4.3* 10-10 m2/s and at 1400°C for 20wt.%CaO-40wt.%SiO2-40wt.%FeO slag, and 1.3*10-10 m2/s at 1250°C for 20wt.%CaO-40wt.%SiO2-40wt.%FeO slag.It was also verified that, if the basicity and ferrite content of the bulk slag are low, then a calcium silicate film forms on the lime surface, and drastically deters the lime dissolution."

Jan 1, 2004

A Joint Venture between Hope Bay Gold Corporation and Miramar Mining Corporation recently acquired the Hope Bay project in Nunavut, which represents the first discovery of a major new Archean greenstone gold belt in Canada since the discovery of Hemlo in 1982 and the Yellowknife belt in 1938. Located some 685 km North of Yellowknife, the Hope Bay Belt is geologically comparable to the other major gold producing regions of Canada. The initial discovery of gold mineralization in 1992 led BHP to acquire virtually all of the Hope Bay belt. Over the subsequent 6 years, BHP expended C$85 million on exploration, including 180,000 meters of drilling, 2.3km of underground workings and a 27,000 tonne bulk sample, as well as extensive environmental and economic studies. Hope Bay Gold and Miramar acquired the Hope Bay property in December 1999 for a cost of C$27 million, considerably less than the C$85 million spent by BHP in exploring the property. They both hold 50% of the project, and share expenses equally. Hope Bay Gold is the manager of all exploration phases and Miramar will manage feasibility, construction and operations. The Hope Bay Joint Venture controls 1,117 sq. km., covering virtually the entire 80 km long Hope Bay and adjacent Elu greenstone belts. We believe that Hope Bay is one of the best-undeveloped gold projects in Canada. Work to date has defined a global resource in excess of three million ounces of gold in three principal deposits, each of which is open to extension along strike and to depth. A C$17 million work program for year 2000 focused on advancing a significant portion of the gold resource to a measured and indicated category. This will provide the basis for initiation of a feasibility study in 2001. The 2000 drill program was one of the largest undertaken in Canada last year, and is a clear indication of our confidence that Hope Bay will develop into a major gold producing district. The majority of the potential mineable areas known to date lie within 350m of surface and would be accessed through a combination of open pit and declines. Currently, development of a 1,800 to 2,000 tpd gold mine producing in excess of 300,000 ounces of gold per year at cash costs below $US200 per ounce is envisioned. In addition, the exploration potential on the 80 km gold belt at Hope Bay is clearly tremendous.

May 1, 2001

By David J. Forrester

Light metals, most commonly aluminum, magnesium and titanium, and alloys containing them, are used in many industrial applications where lightness, hardness, ductility and resistance to corrosion are needed. However, these metals and their alloys can be potential ignition sources in underground coal mines. There have been documented cases in the past where coal mine explosions have been attributed to firedamp/coal dust ignitions involving light metals or their alloys. When light metals and their alloys are brought into contact with oxygen bearing material, such as iron oxide (rust) in the presence of heat, then a "thermite" reaction can occur. This source of heat can be generated from frictional contact or from merely a glancing blow. This paper outlines the hazards associated with light alloys, how to address the hazard and regulatory aspects.

May 1, 2001

By David S. Robertson

"IntroductionCanada has been one of the world's leading producers of uranium since atomic energy first became of practical importance in 1942. Indeed, prior to this time, between 1933 and 1940, Canada produced significant amounts of pitchblende, as a source of radium, from the Eldorado Mine at Great Bear Lake*.Uranium was first reported in Canada, however, in the middle of the 19th Century in the vicinity of Theano Point on Lake Superior north of Sault Ste. Marie. In the early 1900s, uranium-bearing minerals were reported in Quebec north of the St. Lawrence River and in pegmatites in Quebec and eastern Ontario. In 1930, G.A. LaBine and E.C. St. Paul visited an occurrence of cobalt reported by the Geological Survey of Canada in 1900, and brought the Eldorado Mine into production in 1933, as noted above, producing, in the main, silver and pitchblende.In 1942, developments in atomic energy were such that the Government of Canada, at the behest of Great Britain and the United States, requested that Eldorado, which had been closed in 1940, be re-opened to produce uranium for the Manhattan Project. In September, 1943, all discoveries of radioactive minerals were reserved to the Crown and their staking by private interests was banned. In January, 1944, the government nationalized Eldorado and formed a Crown corporation, the present Eldorado Nuclear Limited, to take over the assets. That year marked the formal beginning of uranium exploration in Canada.The Period 1944 to 1948In 1944, the Crown Corporation and the Geological Survey of Canada began exploring for uranium deposits, largely in the areas of Great Bear Lake and Lake Athabasca. In that year, A. W. Joliffe of the Survey visited properties on the north shore of Lake Athabasca near Beaverlodge Lake and recommended that Eldorado acquire claims in the area. In 1946, P. St. Louis and E. Laurum, prospectors working for Eldorado, found the pitchblende veinlets that led to the Ace Mine. Shaft sinking began in 1951, and production, through a carbonate leach plant, began in 1953.Continuing drilling on the Eldorado claims led to the Verna ore bodies, some 6,000 feet northeast of Ace, on which shaft sinking started in 1954."

Jan 1, 1986

By D. G. Brophey, J. A. O’Neill

"High costs, both in terms of human resources and financial costs, have long been the end result of accidents involving vehicles which continue to occur too often throughout our industry.For example, radio remote control LHDs too often seriously injure their operators in underground operations. Costly efforts are required by mine owners to provide safety bays and platforms from which their operators can work safely. In open pit operations, large heavy haulers have too frequently backed over vehicles or turned into vehicles unfortunate enough to be situated in their large blind spots. These are just two examples of situations that have occurred again and again under similar circumstances.Meanwhile, electronic methods of detecting proximity to vehicles have continued to develop. The time has come for the industry to think “outside the box” to evaluate whether many of these new methods can solve these recurring problems.This note takes a look at various types of proximity detection technologies that are in use today in other industries, and discusses the various potential applications within our industry."

Jan 1, 1998

By Agbo Chima

Low-lying sections of open-pit mines accumulate water, especially during the rainy seasons, preventing access to resource-bearing areas. To sustain mining operations, the water must be lifted out of the flooded pits at a high flow rate using pumps. These pumps need to be mobile so that they can be removed during drill-and-blast operations. Most mobile pumps rely on diesel engines with high maintenance requirements. A special pump design was developed to address the unique needs of open-pit mining while making the dewatering process more sustainable. Using the target flow rate and head data, an efficient pump was designed, encased, and deployed in the open pit. A variable speed drive (VSD) was installed in a protective skid so that the pump could be tuned to match the preferred flow rate at any point during its operation. This system was tied to the national electrical grid instead of being powered by diesel pumps, which reduced the carbon intensity per kilowatt-hour. The high availability, low maintenance requirement, and greater reliability reduced the use of spare parts, the fuel consumption, and the logistics associated with operating the pump. This further reduced the carbon footprint of the dewatering process. This paper provides some of the two-year performance metrics for a deployment in West Africa. With a focus on availability, maintenance costs, average cost per volume lifted, and carbon footprint, this encased pump system is compared to the diesel-driven pumps that it aims to replace.

Jan 1, 2023

By J. Lu, D. G. Ivey, H. Henein

Microalloyed steels are widely used in the oil and gas industry. They are a class of high strength, low carbon steels containing small additions of niobium (Nb), titanium (Ti), molybdenum (Mo) and/or vanadium (V). These steels have good strength, toughness and excellent weldability, which are attributed in part to the presence of nano-sized carbides, nitrides and carbonitrides. In the pursuit of developing higher strength microalloyed steels, it is of great interest to quantify the size, distribution, volume fraction and chemical speciation of these precipitates. However, characterization techniques suitable for quantifying fine precipitates are limited. Possible characterization techniques include SEM, TEM and matrix dissolution. A comparison is presented of the various techniques.

Jan 1, 2005

By L. Telfer

Summary During Palaeozoic time, there were deposited in the Canadian Rockies four beds of phosphate rock, ranging in age from Mississippian to Jurassic. Two of these beds are of probable economic importance if some means of separating the phosphate from the gangue can be devised. All the more important beds of phosphate rock so far discovered are just behind the front ranges of the Rocky mountains, within fifty miles of the prairie lands of Alberta. Mining conditions are favourable, with an abundance of timber and ample power available. The phosphate beds are all of the sedimentary type, and they all occur, apparently, at the same stratigraphic horizons over a wide area. The conditions necessary for deposition evidently occurred at several different periods in geological time, and were widespread. The most important factor appears to have been the condition of the land surface surrounding the basin of de-position. Both oolitic and nodular phosphate were laid down under nearly similar conditions. Introduction Following the discovery of phosphate rock in Idaho and Montana, search was commenced in Canada to determine whether formations of similar age in the Canadian Rockies carried similar beds of phosphate. The most widespread search has been that undertaken by the mines department of the Consolidated Mining and Smelting Company of Canada. The following paper will discuss some of the results of this exploration.

Jan 1, 1933

By Charles Tkaczuk

Key issues ? Process control is a corporate function implemented locally. ? Security and documentation is mandatory requiring standard practices. ? Publish and communicate activities (do not re-invent the wheel). ? Payback metric system for all projects. ? Partnering with vendors based on experience, expertise and joint R&D. ? Focus on phased process control projects and distribution of costs. ? Integration of services and functions. ? Application of global standards. ? Big picture application thinking.

Apr 1, 2005

By S. Mamonov, V. ?shikhin

"The purpose of work was the significant increase of copper recovery from slag at a concentrating plant. Analysis of study of slag phase composition showed the perspective of a slow slag cooling method due to its recrystallization and transition of primary copper minerals to secondary.Copper content in base slag varied between 0.71 and 0.96%. The study of a degree of copper minerals release of the slowly cooled slag in comparison with a yielding slag showed that in a flotation size grade –0.071 mm of yielding slag the weight ratio of released copper minerals grains is 58.95% against 86.73% in samples of slowly cooled slag. The process flotation sheet consists of three main, one control and two cleaner flotation operations with aftergrinding of middling products. A reagent mode was differed from a factory one by decreasing the slurry pH from 11–12 to 8–9. This paper shows research results of the slurry alkalinity impact on technological indexes of beneficiation (flotation).Industrial testing of a resulted batch of slowly cooled slag at “SUMZ” concentrating plant showed the efficiency of such processing: copper recovery to a copper concentrate increased by 15–19%.INTRODUCTIONIntensive development of mining and metallurgy industries within a 250-year period in the Ural region led to forming of approximately 315 man-made mineral formations at the territory of the Sverdlovsk region. The region contain over 32.5 billion tons of barren rocks and out of balance ores, over 1.5 billion tons of tailings, over 115 million tons of slimes, and over 100 million tons of metallurgical slag (Demin et al., 2000). Latters, at average, contain 407 thousand tons of copper, 2519 thousand tons of zinc, 7 tons of gold, and 150 tons of silver (Rudoy et al., 2011). Wastes generated in mining processing and metallurgical sector of economy contain not only thousands tons of copper and zinc, but cause significant damage to the environment where they are located. The reduction of negative impact of anthropogenic wastes on the environment as well as the storage volume reduction of valuable metals from dump slags is possible by improving the efficiency of the melting and further flotation of slags formed during this process."

Jan 1, 2016

By Craig Haase

A. Introduction

Jan 1, 2003

By Doug Milne

Linking Classification Systems with each other Similar Parameters between systems Different Rock Mass Properties Rock Mass Classification parameters and geology Different sources of data Commonly Used Rock Mass Classification Systems Q? = Q with SRF = 1.0 RMR? = RMR with no joint orientation correction RMR76 = 9lnQ + 44 RMR?76 = 9lnQ? + 44 RMR76 = RMR89-5 RMR?76 = GSI = RMR89-5 MRMR = ??MRMR

May 1, 2013