Search Documents

By A. W. JR. Whitaker

Introduction Within the last quarter of a century the Lake St. John-Saguenay valley has been converted from a quiet agricultural district to one of the important industrial centres in the Dominion. First there was the expansion -of the pulp and paper industry, and then, starting a little over ten years, ago, the development, in large .blocks, of the enormous hydro-electric power resources of the Saguenay river. Coincident with this power development, the world aluminum industry was rapidly expanding and looking for a new source of cheap power. This was found in the Saguenay valley-and so, in 1925, Arvida was established by the Aluminum Company of Canada as a location for one of the largest aluminum plants in the world. Arvida, an incorporated city comprising an area of some ten square miles, is ideally located on a more or less level plateau about 350 feet above the Saguenay river. Seldom has industry stepped boldly forth and carved out of Nature a community with full city status. The process usually goes through the steps of camp, village, town, and city, involving improper planning or lack of planning; all of which has been avoided at Arvida by starting out in the right way. While this community has only a population of approximately 2,000 at the present time, it is carefully planned for a population many times this figure. Streets, city parks, business and residential sections, have been definitely planned, and, with a City government, proper ordinances were passed at the beginning to ensure the building and maintenance of a model industrial community. As the crow flies, Arvida is about 35 miles due east of lake St. John, and 0 miles west of the St. Lawrence river at Tadoussac. From a shipping standpoint, it is well served by the Canadian National railways, with direct lines to Quebec and Montreal, and by ocean shipping facilities at Port Alfred, which is about 15 miles to the east on the Saguenay river and is served by the Roberval & Saguenay railway. The latter has interchange connections with the Canadian National at Arivda, and also operates a branch line into the city of Chicoutimi.

Jan 1, 1933

By Carl Lausen

Within recent years several mining companies have sent expeditions co the east end of Great Slave lake co determine the mineral possibilities of that area. Little was known of the geography of the region, and even less of the geology; and, not until Blancher's survey was made and the results published, was an accurate map of the lake available. Early explorers followed the Inconnu channel and the north shore of McLeod bay to Port Reliance, and, just prior to Blancher's survey, Hornby showed that the southern passage was feasible. Apparently, but few geologists have ? travelled through the country, for geological information is meager. In 1900, Robert Bell, of the Geological Survey, made a trip to Fort Reliance by way of the north shore of McLeod bay, and he gives a brief description of the geology. The present paper is the result of an expedition into this little-known region by Mr. Geo. M. Douglas and the writer in the summer of 1928. The south shore of Great Slave lake was followed to the east end of Tochatwi bay, and an extensive exploration was made of Kahochella and Pethei peninsulas. The prime object of the expedition was co determine the presence or absence of the copper-bearing Keweenawan basalts.

Jan 1, 1929

By Patrick Fantin

Mining ? The Past Safety Not a priority; Health Not a priority; Energy Manual Labour; Horsepower? Literally. Financially Robust For the Owner?s; Mining ? The Future Safety Zero Harm Health Understanding and elimination of Industrial Disease Energy Efficient use of energy through technology. Full value of renewable energy. Financially Robust Continually build shareholder value through optimum CAPEX/OPEX.

May 1, 2013

By M. Grenon

OBJECTIVE ?To link slope stability and financial assessment algorithms into a commercially available mine design software packages to provide integrated global pit optimization.

May 1, 2013

By A. C. Halferdahl

The Granby ores may be divided into three groups or classes. The No. I ore is a heavy pyrite, chalcopyrite, pyrrhotite, sulphide carrying some free silica, and calcite. No. 2 ore carries the same general group of sulphides as does No. 1, but in a lesser amount. The gangue is an altered greenstone. No. 3 ore has a smaller amount of sulphides than either of the others. Analyses of these ores is as follows: Cu. Si02 Fe. CaO S. Al 203 MgO No. I. Per Cent. 1.8 17.5 33.0 5.7 34.5 2.3 1.3 No. 2 Per cent. 2. 0 35. 6 23. 9 4. 3 I .5. 0 9. 2 6 .. 0 No. 3, Per cent. 1 . 5 40. 9 21 . 7 3. 0 I 1 . 3 11 . 0 5 . 4 The sulphide minerals in No. 2 and No. 3 ores occur largely in bands in the gangue, and for these portions comparatively coarse grinding serves to release the gangue. Drill cores show a certain dissemination of sulphides in portions of the rock, so that grinding to 5 per cent. + 65 mesh with 65 per cent.-200 mesh liberates the sulphide minerals very completely. The association of the sulphides is fundamental. The pyrite was probably deposited first and was followed by a portion of the chalcopyrite, or these two portions of the sulphide minerals were deposited together.

Jan 1, 1924

By Ursula M. Franklin

Old iron nails are one of the most common objects which entice the general public to ask questions about the history of metallurgy. There is a lot of history in old nails - history of the manufacturing industry, and social and economic history. Nails, therefore, are fine teaching tools; whether students have to acquire metallurgical skills or explore the structure and properties of wrought iron, whether they want to look into the history of inventions and the development of machinery, studying nails tells a story better than any teacher or any book. I have used this approach often and the following note is based on several student projects, particularly the work of Carmina Herrero and Vicky Marchant. Nails, those essential metallic fasteners, have long been with us. Their size, shape and design is basically a compromise between the makers' ability to control and manipulate material and the demands of the intended application. There were copper and bronze nails in antiquity, but in this paper I want to deal only with iron nails. In Rome, iron nails were common, and Cleere carried out the fine metallographic investigations on a large stock of nails recovered from a Roman fort site in Scotland. Those nails were hand forged; sorting them at the site on the basis of length, shape of head and shape of shank (in cross section) indicated that there seemed to have been some nail standardization. It appears that the Roman smiths used a series of heading dies starting with a 1/s-in. size. Each successive size increased by approximately 1/16-in. The metallographic inspection of the microstructures of the nails showed that the smaller nails were made in the one operation; i.e. both the tapering and the formation were accomplished on the heated rod without reheating. However, in the case of the larger nails, the nail had to be reheated for the tapering after the head had been forged. Most nails were tapered on all four sides of the shank and the shanks were square in cross section; only one group had rounded shanks. Most heads were flat disks, but in one group the heads were pyramids and another group had conic heads. Figure 1 shows the procedure used to produce the pyramidal heads. Obviously, Roman nail making was sophisticated and each nail design was meant for a particular use.

Jan 1, 1999

By A. Pawelczyk, D. Hreniak, E. Zych, W. Strek, K. Grabas, A. Ostrowski

"Mongolia is a country rich in rare earth resources. In the experiments carried out samples of the Mongolian ore were processed to obtain a lanthanide concentrate. The concentrate underwent hydrometallurgical processing. At the same time radioactive elements were removed. The lanthanides were obtained in the form of hydroxides that were further processed in order to get concentrated products. As a result cerium, lanthanum and neodymium-praseodymium concentrates were separated in the process. Also a concentrate of remaining elements: samarium, europium, gadolinium, terbium, dysprosium, holmium and erbium was obtained. INTRODUCTIONAccording to the assessment of the US Geological Survey, Mongolia possesses 16.77 % of the world total rare earth (RE) resources (Daly, 2011); that is the second largest RE reserve in the world, estimated to be 31 million tonnes in terms of rare earth oxides (REO). In the face of Chinese RE trade restrictions, Mongolia emerged as an important economical partner in mining and exploitation of these critical raw materials. This country is recognized as having more than five large RE deposits in the southern provinces. The most important are Lugeengol (Lugin Gol), Mushgia Khudag, Khotgor and Khalzan Buregtei (Eurasia, 2010). The Mongolian government has taken measures to facilitate western investments, nevertheless the country is economically dependent on China, the basic trading partner, particularly where exports are concerned.In the late 1970s Hydromet Kowary Enterprise, Poland, took up, along with the Wroclaw University of Technology, research and technological study on lanthanides recovery from raw materials of Vietnamese and Mongolian origin and from Indian monazite sands (Kowalczyk, 1990; Kowalczyk & Mazanek, 1987; 1990). For that purpose, a rare earth processing plant had been constructed with the capacity of about 10 t/year of hydroxide concentrate. The facility included several technological operations like grinding, flotation, hydroxide concentrate production in the hydrometallurgical processing, particular RE separation, and production of commercial products in form of CeO2, La2O3, Nd2O3, Pr2O3, and misch metal. Additionally work had been carried out in Kowary on the manufacture of yttrium and europium oxides of high purity, which were intended for color TV picture tube production in Poland."

Jan 1, 2012

By R. C. Rowe

DR. W. F. GRAY (Contributed discussion, presented at meeting by Mr. S. C. Mifilen): Mr. Rowe's suggestion that the Institute should organize itself to interpret the needs of the mining industry to federal and provincial mines departments should commend itself to our membership as sensible and practical, and as one which these public administrative bodies may welcome. One has to start with the premise that those who head the departments of mines in question have the welfare of the industry at heart. Also, it must be postulated that the technical viewpoint of our membership is necessarily free of political considerations. With these reservations, one ventures to state that both Mr. Rowe in his communication to the present session of the Institute, and Professor M. Y. Williams in his earlier communication to the Western Meeting, on The Geological Survey and Mining Development (1), voice the regret general among our membership at the abandonment of the honoured name, and to some extent of the status, of the Geological Survey of Canada. The writer, in 1932, devoted his Presidential Address to the Institute to an appreciation of the value to Canadian mining of the Geological Survey of Canada (2), affirming the desire of the Institute "that the work of the Survey shall be maintained at the highest pitch of efficiency the resources of our country will permit, because, to scrimp expenses on the Survey, is 'to save at the spigot and lose at the bunghole'." He believes that is still the opinion of the Institute, and, if contraction of the usefulness of the Survey is feared by our members at this time, it is incumbent upon the Institute, in fairness to those who direct our government, to say so in precise and explicit terms. Mr. Rowe puts the situation pithily when he writes: "We have reached a stage in our development where a stock-taking and co-ordination of existing knowledge and data is essential. This is a part of that basic function of Dominion mineral technical services which is national and not provincial in its scope".

Jan 1, 1939

By K. W. Major

"This chapter outlines the organization of mine/ mill complexes in Canadian mining companies. Many factors unique to the Canadian mining industry will affect the design of the organization in the future: geographic location, the size and the type of orebody, etc. Mining companies cannot choose where new operations will be located, that is dictated by the location of the orebody. New mines are seldom started near established communities. Rather, the towns usually grow up near the mines. The remoteness of most Canadian mining operations has caused severe problems in attracting and/ or retaining all levels of employees. This means that training has a high priority within each operation.Another factor affecting mine/ mill organizations is the size of the operation. Larger operations generally require more departments and increased specialization to manage equipment and manpower effectively. Thus, for mine/mill complexes, organizational charts are less standardized than in other industries. It is often necessary to organize around the work force rather than develop a chart and then acquire the trained personnel to fill the diagrammed positions.The information presented in this chapter has been derived from the responses received from a survey of Canadian mining operations.Principles of OrganizationOrganization can be defined as deployment of personnel to accomplish definite goals. In the mining industry, the major goals are typically the projected number of tons and grade of ore mined on a daily, weekly, monthly and yearly basis. Organizing involves establishment of authority relationships with provisions for both vertical and horizontal co-ordination within the company structure. Vertical co-ordination is the delegation of responsibility and communication of goals and reporting of progress between the supervisor and subordinate. Horizontal co-ordination is communication between departments at positions of equal authority to determine methods of achieving predefined goals. The organization structure must reflect the objectives and plans of the company, and must clearly define areas of authority.Two criteria for effective organization are departmentalization and manpower planning."

Jan 1, 1989

By F. J. Hrach, K. P. Flynn, P. J. Miranda

"ST Equipment & Technology, LLC (STET) has developed a processing system based on tribo-electrostatic belt separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. In contrast to other electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the triboelectric belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (300 µm) particles with very high throughput. The high efficiency multi-stage separation through internal charging/recharging and recycle results in far superior separations that can be achieved with a conventional single-stage free-fall tribo-electrostatic separator. The triboelectric belt separator technology has been used to separate a wide range of materials including mixtures of glassy aluminosilicates/carbon, calcite/quartz, talc/magnesite, and barite/quartz. Separation results are presented for selected industrial mineral sources. An economic comparison of using the tribo-electrostatic belt separation versus conventional flotation for barite / quartz separation illustrates the advantages of dry processing for minerals.INTRODUCTIONThe lack of access to fresh water is becoming a major factor affecting the feasibility of mining projects around the world. According to Hubert Fleming, former global director for Hatch Water, “Of all the mining projects in the world that have either been stopped or slowed down over the past year, it has been, in almost 100% of the cases, a result of water, either directly or indirectly” (Blin et al., 2013). Dry mineral processing methods offer a solution to this looming problem."

Jan 1, 2016

By R. A. Halet

"The Malartic Gold Fields mine is a good example of the association of ore deposits with a major fault zone. It also exemplifies the control exerted by the physical and chemical character of the host rocks on the localization of orebodies.The mine is in Fourniere and Dubuisson townships, Abitibi county. It is 6 miles east of the town of Malartic, 9n the main highway and railway from Noranda to Val d'Or.The discovery of the mine is due largely to the enterprise of the late J. P. Norrie, who organized the present Company in 1935. The ground is entirely covered by overburden, but Mr. Norrie believed that the extension of the Cadillac-Malartic 'break', the principal ore-bearing structure of the district, would be found on this group of claims. This belief was supported by the discovery of gold-bearing float in the area, and was confirmed by a dip-needle survey and a few pilot diamond drill holes that showed that the favourable Malartic greenstone band passes through the centre of the property.In this way the most favourable area for prospecting was narrowed to a zone 2 ½ miles long by ½ mile wide underlain' by greenstone. The remainder of the property is underlain by sedimentary rocks, which, from experience elsewhere in the camp, were not considered as promising. However, as the entire surface is covered by deep overburden, the location of orebodies even within this more or less restricted area could be accomplished only by a long campaign of diamond drilling. Systematic diamond drilling began in 1936.The contacts of the greenstone band were considered to be the most promising places to begin the work, and the early drilling was concentrated on the south contact, because the orebody of the East Malartic mine, 4 miles to the west, had been discovered on this structure and it was reasonable to hope for a repetition of these conditions. Although the south contact was very thoroughly explored, with a certain amount of encouragement, the work did not prove the existence of deposits of ore grade, and attention was shifted to the north contact zone of the greenstone band. In this locality much more promising results were obtained, and a number of good orebodies were outlined."

Jan 1, 1954

By A. Kowalski

Telvis Limited, manufacturer of an emergency communication dispatcher&apos;s broadcasting system, now introduces the possibility of a remote software upgrade to its devices. The paper presents methods, features and ways to accomplish this task. It describes the mechanisms used and the opportunities that arise from the use of this type of functionality. The mechanism software update presented applies to devices on the surface and in underground areas of mines. The electronics used currently allow the use of remote software updates, but the mining equipment makes little use of these methods. This paper aims to start the discussion on this topic and tries to lay the path of development by showing one of the first examples of the application.

Aug 1, 2013

By M. S. Badollet

Introduction The manufacture of some asbestos products involves the use of asbestos in combination with water, cement and granular fillers. This type of production is often called the wet or semi-wet process and requires the use of either pressure or vacuum to eliminate the excess water in the fibrous blend so that the product may develop the proper strength during the curing stage. Asbestos - cement products available today are numerous and are a valuable contribution to the building industry. Their production in quantity depends upon the type of equipment employed, the speed at which it can be operated, and the factors involving the? blending of asbestos, cement, water, and fillers. Assuming that all mechanical troubles at a plant have been eliminated or are under control it is still advisable to study the basic properties of the raw materials used in the asbestos-cement products. The type of cement used is an important factor, but usually the manufacturer of the cement is willing to work with the asbestos development engineer and recommend the proper type to be used for the product. The source of the water should not be overlooked as a general factor involved in the production cycle. Waters containing a high percentage of contamination such as silts, humus, or soluble salts may adversely affect the setting of the cement or cause a slowing down of the production rate in the factory. Asbestos in combination with cement is an ideal material fo1 building products. It is inorganic, will not deteriorate, and can be handled by mechanical equipment with a minimum reduction of fibre length. The many physical properties peculiar to asbestos fibres should be well understood by the manufacturer. They may be briefly enumerated as follows: fibre strength, fibre composition, sliminess, length, harshness, softness, and filterability or porosity. This last named property is important and it is the purpose of this paper to present some basic studies on filtration as applied to production problems.

Jan 1, 1949

By V. Estrada, G. Aguilera

"Since the most of mineral processing are wet, and for more specific applications where it is necessary to increase the purity through leaching and / or concentration, the proper dispersion is the first, and perhaps more crucial stage in the whole chain of processing. This specific process is based on the formation of a dispersion or suspension of mineral, trying to make the mixture as homogeneous as possible, and with specific rheological conditions. Sometimes it is not enough agitation to make it happen, so that chemical additives are used as an aid. However, the addition of chemicals strongly alters the viscosity and other rheological properties of the suspension factor to consider for subsequent steps to ore beneficiation. In other hand, in a process where no chemicals used often employ large quantities of water to achieve dispersion. But if an efficient chemical agent, which optimizes said dispersion through a specific physicochemical effect on the particle surface is used, also it can generate rheological advantages, besides achieving rational use of water and increase the recoveries of the product main about also optimal costs. The aim of this work is to find the optimal rheological conditions for a dispersion of kaolin as study case, looking for stability, best disaggregation, viscosity and pseudoplasticity.To find the optimal additive, the evaluation parameters were: 1) Best degree of dispersion of the suspensions according to the analysis of the flow curve; 2) Best level of disaggregation of particle chemical analysis delaminated by Particle Size Distribution; and 3) Best thixotropic rheological parameters and pseudoplasticity. Finally the optimum additive as one that meets the best combination of parameters is proposed.INTRODUCTIONKaolin is a clay material formed by altering of feldspar composed mainly for kaolinite. Depending on the application, the kaolin as raw material must be refined and processed because the ores of clays contain usually a lot of impurities derived of its sedimentary source, such as feldspar, mica and quartz (Torres, et. al., 2011). According to the experience on the plant floor and the publication of several scientific papers, it is known that the dispersion is a crucial stage in mineral processing (Greene, Duke, & Hunter, 1965) (Raghavan, et. al., 2004), not only because of the disaggregation of particles, besides because of the humectation of them. Is clear that disaggregation of particles give to the suspensions rheological stability, and the humectation improves the effect of further processes like grinding or chemical treatment. The dispersion process involves making a suspension of the mineral with a solvent which is usually water, to obtain a homogeneous dispersion, with the aid of energy of stirring. Sometimes is not enough the agitation (even with high energy) for this to occur, so is necessary the use of dispersing substances which introduce ions and molecules as modifiers of chemical potential, forcing the molecules of the material to disperse. Sometimes their use even could affect the pH of the suspension in a non-desirable condition. (Flores, 2013)."

Jan 1, 2016

By A. Musschoot

"The paper will review general types and designs of vibratory feeders, describing briefly the design features and characteristics that apply to the application of specific types. Control considerations for selecting types will be dis• cussed, such as fixed or adjustable, manual or automatic, individual or multiple bank, and process requirements. Design parameters for hopper openings and installation geometry will be discussed, including consideration of material size distribution, segregation, moisture content and other characteristics, based on practical applications and experience as well as theory. Pan designs and the selection of pan materials will also be discussed with reference to wear, corrosion, impact and practical economic factors."

Jan 1, 1972

By D. Sharma, A. K. Singh, R. Singh, P. K. Mandal, M. Sarkar

"This paper deals with the stability investigations carried out at the XIVth seam of Jitpur colliery. The study was conducted to investigate the possible causes of roof cavity formation and face spalling at the middle slice face of block-3 longwall panel and to suggest remedial measures. The instrumentation and monitoring work was carried out in the panel over a period of nine months. On the basis of observations, it was found that if the maximum face span was reduced from the existing 4.8 m to 3.6 m, and if the face time schedule cycle was reduced from a maximum of 37 days to about 18 days, this problem could be eliminated. The recommendations of CMRI have been implemented in the middle slice face of block-4 panel with success. IntroductionModerate to steeply dipping, undisturbed seams of uniform thickness are worked by way of inclined slicing parallel to walls. In this method, the seams are treated as a combination of several moderately thick seams dipping parallel to roof and floor. Numerous variations of multislice mining have been used worldwide to get high coal recovery under local conditions of geology, subsidence control, proness to spontaneous combustion, statutes and economics. Multislice mining can proceed either downward descending from the roof or upward ascending from the floor. Ascending methods require backfill behind the working face to provide a base for the next slice. It is also adopted for surface protection against subsidence or mining under a massive roof. This paper presents a scientific study conducted in Jitpur colliery, IISCO where a 9 m thick seam is mined in three slices in ascending order with stowing."

Jan 1, 2002

By T. Guan, G. Fu, X. Zhou, L. Deng

"One kind of tailings from gravity separation of polymetallic mine contains 0.5–0.8% SnO2. The proportion of –0.037 mm size fraction of the tailings is 37.12%, and the distribution rate of SnO2 is 60.32% in it. For this tailings, two processing technology was carried out. One was felt-shaking table gravity separation in which the concentrate with a grade of 30% SnO2 at a recovery of 10% was obtained. Another was flotation-gravity separation in which the concentrate with a grade of 51.20% SnO2 at a recovery of 51.69% was obtained, but the dosage of collectors was as much as 990g/t. Therefore, the experimental research on the influence of grain size composition on the cassiterite recovery were conducted. The results show that: (1) the flotation recovery of the cassiterite distributed in +0.043 mm size fraction is only 10%, flotation recovery is not suitable for it; (2) a portion of cassiterite distributed in –0.01+0.005 mm size fraction could be recovered by flotation, but the tin flotation performance will be worsened rapidly and the dosage of collectors will be increased due to the increase of the content of –0.010 mm size fraction; (3) flotation processing is not suitable for –0.005 mm size fraction of the tailings. According to the results, a new technology has been carried out, that is discarding tailings by gravity separation-hydrocyclone desliming-flotation-gravity separation processing flow. The processing index is close to that of the flotation-gravity separation processing flow, and the collector dosage is decreased to 360 g/t by this processing technology. And, it has been achieved that the cassiterite slime is recovered economically and reasonably.INTRODUCTIONAs the density of cassiterite is higher than that of gangue, gravity separation is considered to be a low cost, pollution free, and effective process for cassiterite recovery (Wills, 2009). However, cassiterite is a kind of fragile mineral, over crushing is easy to take place and a large amount of slime is inevitably produced in the crushing and grinding of cassiterite. For the cassiterite slime exists in –0.043 mm size fraction, the efficiency of gravity separation decreases sharply. The production practice shows that, for the fine cassiterite, the recovery of tin exists in –0.043 mm +0.010 mm size fraction is about 13% through shaking table gravity separation, and the tin exists in –0.010 mm size fraction is almost impossible to be recovered by gravity separation. If flotation is adopted to recover fine cassiterite, the problems of high reagent dosage, high cost, environmental pollution, and poor economic benefit would take place. Therefore, the recovery of cassiterite slime is a worldwide problem. A key way to increase the utilization of tin resource and increase the economic benefit of tin mines is developing suitable beneficiation process for fine cassiterite."

Jan 1, 2016

By A. Boeing

Rock-breaker automation and remote operation improves the safety and efficiency of mining operations. This article presents an overview of the Rocklogic rock-breaker automation system architecture that provides collision avoidance, automated parking, and remote operation functionality. The system consists of a distributed computer control system that interfaces with sensors attached to the rock-breaker, the rock-breaker hydraulics, and the site infrastructure. We present results of an automated Transmin rockbreaker installed in a production environment at an underground Australian mine site. The system has been in production use for over 900 days during which there have been no reported collisions, and 100% adoption of the remote operation technology. As a result, Rocklogic has significantly improved the safety of rock-breaking operations and reduced the rock-breaking cycle time, thereby improving the sites overall throughput.

Aug 1, 2013

By P. Tarassoff

Extractive metallurgy is concerned with the winning of metals from their ores and concentrates. It is therefore not unexpected that extractive metallurgy in Canada has always been closely linked with mining. The discovery and exploitation of new orebodies has provided the impetus for the building of many of our smelters and refineries - past and present - and for the development of new metal extraction processes. The purpose of this paper is to provide a brief overview of those early metallurgical developments, and to highlight the continuing expansion and diversification of the Canadian metallurgical industry.

Jan 1, 1999

By K. S. Raja, B. Pesic, S. Kshetri

"We investigated the electrochemical corrosion behavior of commercial permanent magnetic material (NdFeB alloy) in 0.1 M NaH2PO4 solution (pH:4.75) containing 0 – 1000 ppm of chloride at room temperature (298 K). The material was evaluated in magnetized and demagnetized condition with different surface preparations such as: Ni-Cu-Ni coated, uncoated (bare), and anodized (in fluoride containing ethylene glycol at 60 V for 15 minutes to form a thick nanoporous oxide surface). The nickel coated magnetic sample showed reasonable pitting corrosion resistance up to 100 ppm chloride addition. The uncoated samples showed passivity in chloride free phosphate solution. Chloride additions caused pitting and the pitting protection potential was equal to the corrosion potential with 100 ppm chloride addition. Demagnetization did not alter the electrochemical polarization. However, the passive film formed on the magnetic sample showed higher charge carrier density than the film formed on the demagnetized sample. INTRODUCTIONSintered NdFeB permanent magnets exhibit excellent magnetic properties such as large energy product [(BH)max > 450 kJ/m3], high saturation magnetization (1.6 Tesla), and high coercivity (1.2 – 2.08 x 106 A/m) (Sugimoto, 2011). However, the NdFeB magnets are prone to corrosion attack because of the presence of Nd-rich intermetallic phases, such as Nd4Fe (Jurczyk & Jakubowicz, 2000). Nd-rich and B-rich intermetallic phases are distributed in a matrix of Nd2Fe14B tetragonal ferromagnetic compound in a permanent magnet. Generally, several types of Nd-rich phases are present in the magnet with Fe:Nd ratios ranging from 1:1.2 to 1:7. The volume fractions of Nd-rich and B-rich (Nd1+xFe4B4 type) phases are about 10% and 7% respectively (Li, Ma, Li, & Wang, 2011) . Among these intermetallic phases, Nd-rich phase has the most active electrochemical potential. Therefore, dissolution of this phase occurs in preference to other phases by galvanic corrosion when exposed to moisture. Since Nd-rich phases are present at the grain boundaries of the Nd2Fe14B matrix, corrosion leads to disintegration of the magnet."

Jan 1, 2012