Search Documents

By R. A. Gannicott

Trend surface analysis was used to investigate the geochemical dispersion patterns of Si, Ai, Fe, Mg, Ca, Na, K, Ti and Rb in the footwall of the Seneca massive sulphide prospect in southwestern British Columbia. Surfaces for various element ratios were also produced to see if the distributions of the elements are related to each other. Trends developed by the elements redistributed during hydrothermal alteration may be difficult to detect for various reasons, such as too few and widely separated sample points, random analytical errors or local variations in rock chemical composition that are not related to regional trends. Trend surface analysis is useful to distinguish regional trends from local fluctuations. The computer program used in this study is capable of calculating surfaces up to the 6th degree polynomial, but provides for automatic termination when the variables in the equation for successive surfaces become effectively collinear. With the relatively small number of data points used (21 samples) in this study, such termination occurred after the quadratic surface. Results show that, at the Seneca prospect, Mg and K increase, and Na and Ca decrease, toward a common centre which corresponds closely with the best drill-core intersections of ore. The centre is interpreted as a volcanic vent and as the source of mineralization . Quadratic surfaces for element ratios show that K/Ca decreases and Fe/Mg increases away from this vent. Thin-section and X-ray diffraction analyses indicate that these variations reflect sericitization of plagioclase and an increase in the Mg content of chlorite near the vent. The mineralization , rock types and element dispersion patterns at the Seneca prospect are similar to those reported for volcanogenic massive sulphide deposits at Bathurst, New Brunswick, and in the Hokuroko district of Japan.

Jan 1, 1979

By J. L. Luo, D. G. Ivey, A. H. Adeleke

Double-edge-notched flat tensile samples of X70 steel were used for both slow strain-rate testing (SSRT) and cyclic loading testing with the notch located in the zone of interest, i.e., the weld metal (WM), base metal (BM) and heat affected zone (HAZ). By using both optical and scanning electron microscopy, the stress corrosion cracking (SCC) behaviour with respect to crack morphology and various forms of microstructure was investigated. In all the samples considered, the mode of failure was predominantly transgranular with cleavage facets around the edges of the fracture surface. The BM, with a bainitic microstructure, had the highest resistance to SCC when compared with the mixed microstructures of acicular ferrite-primary ferrite and acicular ferrite-grain boundary ferrite observed in the WM and HAZ, respectively. The effect of microstructure on stress corrosion cracking behaviour is discussed based on experimental observations.

Jan 1, 2005

By Jim Hazzard

A numerical investigation is presented to examine fluid flow in fractured rock slopes. In mining geomechanics, different numerical modelling approaches are used to estimate fluid pressures in open pit mines. The most common technique is the Equivalent Porous Medium (EPM) approach in which the fractured rock is assumed to behave as a porous continuum. Depending on the geometry and properties of the problem, this may not always be the best approach. The paper presents a parametric study to examine the effect of fracture spacing, fracture and matrix diffusivity and excavation rate on the fluid behaviour in rock slopes. Based on the model results, guidelines are provided as to when EPM models can be used and when different modelling approaches (e.g., discrete fracture flow) may be necessary.

Jun 1, 2012

By Ted J. Smith, Stephen E. Kesler

"Zonation patterns are welt developed in the mafic metavolcanic rocks that host epigenetic quartz-carbonate-gold vein mineralization at the Hollinger-McIntyre deposit. Carbonate alteration assemblages are strongly zoned about mineralization. Proceeding inward from background greenschist facies rocks to alteration envelopes enclosing individual veins, the following assemblages are observed:Assemblage I-quartz-albite-chlorite-epidote-actinolite-(calcite)Assemblage II-quartz-albite-chlorite-calcite-epidoteAssemblage III-quartz-ankerite-sericite-(chlorite-calcite)Assemblage IV-quartz-albite-ankerite-sericiteLithogeochemical zoning is equally well developed as variations in whole-rock abundances ofAs, Au, Ba, Rb, and Sb. As and Ba form the most useful zonation patterns, outlining individual ore zones as well as broader trends of mineralization.Gas chromatographic analyses of fluid inclusions in the quartz-carbonate veins indicate that the mineralizing fluid was an H20-C02 mixture. Locally, CH4-rich fluid inclusions are associated with graphitic and/or carbonaceous wallrocks. Fluid inclusions in ore-bearing veins have higher CO2 contents than those in non-ore veins. Extensive sampling and analyses of veins from the area surrounding the deposit reveals a well developed zonation of CO2 contents about the main zone of mineralization. Low CO2 levels (1-2 mole%) in veins are peripheral to the deposit and increase to over 12 mole% in mineralized zones.The observed zoning of the carbonate alteration assemblages is a result of the addition of CO2 to the wallrock, which is consistent with the zoning of CO2 in the fluid inclusions.The zoning patterns delineated in this study are useful in exploration both on a deposit scale and on the scale of individual ore zones."

Jan 1, 1985

The fracture behavior of second phase particles and the role of matrix material on the wear resistances of the three Al-Si alloys containing 8, 17, and 19% Si were investigated using single pass scratch testing technique by applying normal loads between 0,15 and 5,00 N, in ambient air, Optical microscopy and SEM with EDS were used to analyze microstructures and morphologies of scratch tracks of the Al-Si alloys, The results showed that needle-like Si particles fractured under a load of 0.50 N, while block-like Si particles fractured at loads above 3,00 N, The Al-17% Si alloy with large number of needle-like particles (area fraction 16,4%) exhibited the highest coefficient of friction (0,8) and the widest scratch track, The Al-19%Si alloy containing high Si percentage and larger number of block-like particles (area fraction 16%) exhibited the lowest coefficient of friction (0,37) and the narrowest scratch track width. Presence of block-like particles was effective in reducing the amount of material transfer from Al-Si alloy surfaces to the counterface.

Jan 1, 2005

By Michel Gauthier, Pierre Marcoux, Gaétan Morin

"The recent opening of Muscocho's gold mine at Montauban, as weil as the discovery of several new copper-gold showings of a similar nature near the confluence of the Saguenay and St , Lawrence has revealed the existence of a new metallogenic gold province which is located within supercrustal units of Helikian age within the Grenville Province. Three metalliferous belts have been identified, each one of which is related to a series of SW-NE trending faults. The first is located in southeastern Ontario and southwestern Quebec. The second extends from the Balmat-Pierrepont mining district of New York State up to the Lac St. Jean region of Quebec, and includes the Montauban camp. The third follows the St. Lawrence river in Charlevoix County and along the north shore of the Gulf of St. Lawrence.The gold mineralization which is present in the central portion of the Grenville Province is of two types: either stratiform or vein. Deposits of the first type, of which the Muscocho is the type locality, are economically the more interesting of the two. Not only is this mineralization stratiform, but also shows a distinct affinity to AI-rich, Mg-rich or calc-silicate-rich bands. As is the case with the Bousquet and Hemlo regions of the Superior Province, they are associated with layers which are rich in sillimanite and occasionally staurolite. A second parallel between the Bousquet and Montauban deposits might be the presence of manganesian gamets, which have been recognized at the two localities. Some of the mineralization in the central Grenville Province is located within thin bands of iron formation which are rich in arsenic.The stratiform gold deposits of the central Grenville Province are of exhalative origin and are located within a volcano-sedimentary terrane. It is probable that a part of the gold present in these Helikian deposits have been derived by remobilization of Archean mineralization. The vein showings form as a consequence of the remobilization of the Helikian strata during the Grenville metamorphism,"

Jan 1, 1985

By Jochen Petersen, Caroline Muzawazi

The technical feasibility of ammonia leaching of PGM bearing Platreef flotation concentrates was investigated as an alternative method for the recovery of base metals prior to precious metal recovery. The composition of the concentrates includes 2.02% Cu and 3.17% Ni, and the major base metal minerals are chalcopyrite and pentlandite. Optimal leaching conditions were initially established in shake flask experiments to be a solution containing 4 M NH4OH, 4 M (NH4)2CO3 and a pH range between 9 and 10. These were used as base case conditions in column and batch stirred tank reactor tests, where the effects of total ammonia concentration and operating temperature were explored further. At optimal conditions nearly 100% Cu and Ni extraction were obtained in the batch stirred tank reactor, and 95% Cu and 60% Ni extraction was obtained in columns. The activation energy for chalcopyrite and pentlandite was 36 kJ/mol and 16 kJ/mol, respectively, in both reactors, indicating different reaction pathways for the two minerals. Gas-liquid mass transfer appears to be the limiting reaction step in columns much more than in tanks, and the degree of ammonia loss to air is significant. This initial test work indicates the feasibility of using ammonia leaching for this and similar materials as an alternative route to conventional smelting and refining prior to PGM recovery, but a number of technical challenges still need to be overcome.

Jan 1, 2014

By K. Barbetti, J. Avraamides

"The processing of gold ores with high silver contents can provide operational challenges, such as high cyanide consumption, retardation of gold leaching and competition during adsorption stages of carbon-in-pulp/leach/column (CIP/CIL/CIC) circuits. In particular, the silver, which is about 1.5% of the value of gold, competes with gold during carbon adsorption due to its higher concentration in many Ag-Au ores, potentially leading to gold solution losses. Fresh and partially fouled (barren and regenerated) activated carbons were evaluated at various Ag:Au ratios and total metal concentrations with regard to the adsorption kinetics and equilibrium loadings. Conventional Freundlich isotherms were found to be highly inaccurate for predicting equilibrium loadings in the competitive adsorption environment. An integrated model, which incorporates competitive adsorption kinetics with a modified competitive adsorption isotherm model has been developed and validated using plant and laboratory data. The model performance and some of its salient features will be discussed.INTRODUCTIONThe processing of gold ores with high silver contents can present a range of operational challenges, such as high cyanide consumption, retardation of gold leaching and competition in carbon adsorption circuits. Silver is often present at significantly higher concentrations than gold in many gold-silver ores and competes with gold in carbon adsorption circuits, limiting the gold loading rate and capacity, resulting in gold solution losses and reduced gold recovery.Curtin University’s Gold Technology Group has evaluated fresh and partially fouled (barren and regenerated) activated carbons at various Ag:Au ratios and total metal concentrations to determine the adsorption kinetics and equilibrium loadings for gold and silver. Conventional Freundlich isotherms were found to be highly inaccurate for predicting equilibrium loadings in the presence of both gold and silver.An integrated model, which incorporates competitive adsorption kinetics with a modified competitive adsorption isotherm model has been developed and validated using plant and laboratory data. This paper describes the model performance and some of its salient features."

Jan 1, 2016

By C. Caballero, M. Rosales, C. León, A. Valencia, R. Fuentes, A. Moyano

Slopping is the formation of waves in the converter due to the gas injection by tuyeres. Those waves produce a premature wearing of the refractory lining of the reactor due to its great amplitude. The affected zones are the tuyere line (outlet gas from tuyeres) and the front of this line. In the present work, a theoretical and experimental study is made to develop a theory that determines the variables involved in slopping, characterizing the more important parameters of operation in the phenomenon of slopping. In addition, this theory will allow for determination of new technological alternatives of the blast injection permitting to depress the slopping phenomenon.

Jan 1, 2007

This paper examines the latest advances in mine hoist motor and drives systems. The technology employed for large hoists has migrated from the traditional DC technology to AC motors with cyclo convertor drives, and more recently, advances in pulse width modulation (PWM) drives have resulted in these being applied to large hoist drives. When combined with PWM drive technology, the induction motor presents the ideal solution for hoist applications This paper examines the factors in choosing a suitable PWM drive and motor for a hoist installation. Factors under consideration include: ? hoist duty cycle, ? drive rating restrictions, ? choice of power semiconductor device,, ? low speed operation, ? maintenance ? reliability The cage induction motor and synchronous motor are compared and it is shown that the induction motor is the motor of choice for large hoists.

May 1, 2010

By Michele L. Kimble

A fast-flow reactor mass spectrometer has been utilized to investigate the reactions of gas-phase gold cluster anions with CO and oxygen. Addition of CO to Aun - produces species of the form Au(CO)m -, where m = 2-5. However, CO does not bind to Au2 - or Au3 -. With oxygen addition in the cluster source, gold oxide species with both molecular and atomized oxygen are produced. The addition of carbon monoxide to these preoxidized gold cluster anions reveals that select species with 1, 2, and 3 gold atoms participate in the oxidation reaction to produce CO2. Bimolecular rate constants for the reactions between these species and CO are also discussed.

Oct 1, 2003

By R. C. Carne, R. J. Cathro

"Most of the recent large discoveries of zinc, lead and silver in Western Canada are Paleozoic-aged stratiform deposits that occur within the limits of the tectonic sub-province of the Canadian Cordillera known as Selwyn Basin. Bounded on either side by coeval carbonate platforms. Selwyn Basin trends northwest for 1300 km from northeast British Columbia to Alaska. Paleozoic rocks of Selwyn Basin consist primarily of chert, shale and coarser-grained clastic sedimentary rocks with minor volcanic rocks.The Selwyn Basin deposits have few counterparts elsewhere in Canada, but have a close similarity in geological setting, mineralogy and morphology to well-known deposits such as McArthur (HYC) in Australia, Meggen and Rammelsberg in West Germany, and Sullivan in British Columbia. Recent studies of these deposits have led to an emerging, but now generally accepted, model of ore deposition in which stratabound zinc-lead-silver shale-hosted or ""sedimentary-exhalative"" (sedex) deposits are precipitated in active tectonic environments from metalliferous geothermal brines that rise to the sea floor along deep-seated fault zones. Although their mineralogy and ore metal zoning can be similar to that of volcanogenic massive sulphide deposits, most sedex deposits have only a weak genetic link with volcanism.Sedex mineralization in Selwyn Basin has been identified within three separate ages of shale or its metamorphosed equivalent. The lower Cambrian-age Anvil Camp in central Yukon Territory contains the only producing mine (Faro). Important lower Silurian-age zinc-lead mineralization is at Howards Pass along the Yukon - Northwest Territories border. Barite and zinc-lead-barite mineralization of upper Devonian age occurs across Selwyn Basin. Potentially economic deposits have been found at Macmillan Pass, along the Yukon - Northwest Territories border and in the Gataga District of northeastern British Columbia."

Jan 1, 1982

By M. Wu, G. Plascencia, A. E. M. Warner, A. Vahed, T. A. Utigard

Nickel oxide granules formed by pyrohydrolysis of a chloride solution, were reduced in hydrogen. Below 400 °C, an incubation period was observed, followed by very slow reduction. In the temperature range from 400 to 600 °C, the rate of reduction increased with increasing temperature and increasing hydrogen pressure. Microscopic analysis showed that in this temperature range the reaction followed the shrinking core model. Above 600 °C, the reduction rate decreased noticeably before suddenly becoming very fast at and above 950 °C. Microscopy showed inner bands of metallization inside the outer metallic rim, indicating partial blockage of the interface between the reacted and un-reacted NiO core. At these temperatures, particle agglomeration and sintering were also found to take place. Surface segregation of sulphur may account for the slow down in reduction rate above 600 °C. From an industrial point of view, reduction should be carried out from 550 to 600 °C with as high a concentration of hydrogen as possible. If sintering and agglomeration are not of any concerns, reduction can be carried extremely fast at about 1000 °C.

Jan 1, 2005

By T. G. Edgeworth

Some of the historical background of the industry is reviewed, with reference to the different types of reduction cells in use for aluminum smelting. Factors to be considered in cell des1gn involve capital, power, and operating costs. The trend is apparently toward larger cells. The industry is studying new construction materials for cell linings, as well as alternate electrolyte compositions and other design changes which will improve productivity and energy efficiency. The aluminum smelting activity in other countries is briefly reviewed. TODA Y'S industrial production of aluminum is still based on the simultaneous discoveries made in 1886 by Charles Martin Hall in Ohio, and Paul Heroult in France. Up to that date, only about 50 tons of aluminum had been produced in the world, and the price at that time was about $5 per pound. Sucl1 figures must be contrasted with the present world aluminum smelting capacity of over five mil-lion tons per year, and a price of about 25 cents per pound.

Jan 1, 1962

By S. Spigarelli

The creep response of the AE44 magnesium alloy was studied by means of constant load creep tests carried out at 125 and 150°C, obtaining that at the latter temperature the minimum creep rate observed under an applied stress of 100 MPa was two orders of magnitude lower in the investigated alloy than in AM50. The minimum creep rate dependence on applied stress was described by a conventional power-law, e = Aon , where A was a temperature dependent parameter and n was the stress exponent, resulting in a n value close to 30, i.e. by far larger than those observed in commercial alloys with similar Al content. This large difference in creep response was attributed to the precipitation of rare earths (RE) intermetallic phases distributed in the grain boundary zone in form of an almost continuous network of dispersoids that were observed by means of scanning electron microscopy.

Jan 1, 2006

By M. Choy, A. Kadiayi, E. Magdzinski

"Design of engineering controls to limit occupational noise exposure rely on accurate calculation inputs. Sound in mines can carry considerable distances. Mine ventilation engineers rely on noise propagation calculations to estimate silencer performance criteria for key mine fan installations that are often in proximity to occupied areas of a mine and can remain in service for decades. The blasted and rockbolted walls of hard rock mining tunnels have unique acoustical properties. Underground testing in an operating metal mine in Sudbury, Canada was performed and results processed to characterize noise propagation in mines, with the goal of improving the accuracy of noise calculations.INTRODUCTIONAs mine operators continue to improve and promote workplace safety, addressing noise at fixed infrastructure locations is observed as increasingly common. Underground fans are important to consider in this context, as they are typically loud, in proximity to occupied and sensitive workplaces, and operate nearly continuously. Predicting noise propagation from ventilation fans within underground mines has long been a challenge, with few available resources documenting acoustical properties as calculation inputs. Other factors in addition to rock face absorption properties include tunnel geometry and distance from the fan, which play critical roles in characterizing the noise level at any given point away from the fan. By understanding and establishing methods to better predict noise dissipation along underground mining tunnels, engineers can design noise controls with a greater degree of precision and confidence to effectively protect workers from over exposure to noise.This paper investigates classical methods of predicting reverberant room and direct field noise propagation. These prediction methods are then compared to noise measurements taken within the Fraser Mine of Glencore’s Sudbury Integrated Nickel Operations (Sudbury INO) Measurements were taken at a depth of ~881 m (2,889 ft), along an ~300 m (984 ft) long blasted hard rock mining tunnel. The noise along the mine tunnel resulted from the intakes of two 900 kW (1,200 hp) ventilation fans with a combined exhaust capacity of 300 m3/s (630,000 cfm)."

Jan 1, 2019

By Luis R. Fonseca, C. Raimat, C. Wendeler, A. Sanz

"Rockfall barriers are widely known as proven efficiency element to protect infrastructure by catching the rock blocks in the falling direction and absorbing the energy generated by them.It’s common in the project design phase and during installation, fix rockfall barriers for catch a high percentage of the falling blocks and in many cases consider as valid the solution when the barrier can capture all of them. However, in many cases it’s possible to consider the use of these protections, simply to guarantee a secure shed for the traffic and intercept simply the blocks that theoretically hit the road surface.The results of the high-energy rockfall protection barriers type GBE which protect GC-200 road in Las Palmas de Gran Canaria are shown in this paper.The topographic data should be especially detailed observed and even more if you want to apply the technique of ""shadow zone"" with a flexible gallery system. It should be drawn from detailed topographic maps and drawings (photogrammetric restitution) to the scales 1/1000, 1/500, or 1/200; and it is important not to ignore the presence of vertical cuts, tracks, small slopes that modify the trajectories (trampoline effect, hard points that favor the rebounds) and which are not always presented in the drawings.The ""shadow zone"" is defined as the protected area, located at a lower elevation to the line created by the rockfall barrier to except of trajectories of rocks and free from the influence of the deflection of the system under the maximum energy level for which it was designed (MEL)."

Jan 1, 2015

By R. C. Wallace

Since the time when Canada's East and West were joined by the railway, and communication was established into the interior, settlements grew on the southern fringe of the great Precambrian area that formed the northern protaxis of the continent during its vicissitudes of growth. They clung precariously to the fringe of that ancient land, for the Precambrian is not generous to those who wish to live by the fruits of the soil, except in those limited areas where the Pleistocene ice-sheet has been profuse in its gifts of clay to cover the hard surface of the Precambrian rock. Later settlements spread westwards over the expanse of Cretacean plains that now form the wheatfields of the Canadian West; but there still remained in northern and western Ontario, in eastern and northern Manitoba, a pioneer race, to whom agriculture had attractions only in so far that it provided the wherewithal to lay siege to the riches of the Precambrian. And they had a vision beyond their time. More than they knew, they had seized the fact that for the complete rounding out of Canadian national life, a8 well as for the establishing of the necessary contributions towards the economic stability of Canada and its provinces, an industry in mining sh01.dd be well and truly built in the hinterland of the central provinces. Failing the winning of mineral from the rocks, and timber from the forests, there would remain between the East and the West an enormous barrier of unproductive country which would not only be an incubus to the agricultural people in their struggle for economic liberty, but would effectively, and for all time, remain an un-populated void across which the aspirations of East and West would be unable to unite.

Jan 1, 1924

? Introduction ? Partenariat MRNF - MAE ? Goldex ? Manitou : - Ré-aménagement du bassin versant - Accès aux zones problématiques - Filtration du ruisseau pour les travaux - Nettoyage près de la rivière - Régulation du débit et bassin - Digues et bassins - Déposition résidus Goldex ? Chemins d?accès Goldex-Manitou ? Pipelines: Goldex ? Retour Goldex ? Manitou ? Station de pompage ? Résumé

Feb 1, 2008

By N. Plint, M. Potgieter

The Anglo Platinum Mogalakwena North concentrator was one of the first three hard rock mineral processing applications to utilise a HPGR circuit in preference to a SAG milling circuit. This was driven by the extreme competence of the ore that had given rise to throughput issues on the original South Plant. Despite more than adequate capacity and performance of the individual comminution units, the circuit has struggled to obtain full design capacity. A thorough review of the integrated performance of the circuit revealed a wide range of bottlenecks and underutilised parts of the circuit arising from design issues. Interestingly, the major opportunities lie in materials handling issues and mismatch of loads about the circuit. This paper presents the high-level outcomes and the associated opportunities, and is pertinent to all HPGR circuit designs.

Jan 1, 2012