Search Documents

By Gerhard W. Heinrich, Gerald V. Schroeder, Daniel A. Murphy, Daniel F. Suarez, Jamie B. Beauchamp

"Washwater 'Finger' sprays were installed and tested in the copper/nickel separation circuit at Strathcona Mill to improve flotation capacities and related metallurgical performances. The new spray design features submerged sideways introduction of wash water into the flotation froth through nozzles at the end of vertical pipes which are suspended from a header above the froth. This maximizes the effective cross sectional area of flotation vessels while maintaining effective froth cleaning and a desirably high density of the concentrate slurry. The plant tests gave increases of copper concentrate production rates of 17% to 20% for conventional cells and 16% to 20% in column flotation at target grades of 29% to 30% copper and of less than 0.5% nickel. Basic considerations and concepts of tests and evaluation procedures are described.IntroductionMeeting flotation concentrate grade targets at maximum production rates and recoveries is a challenge all too familiar to operators of base metal ore concentrators. Frothwashing is an option to improve grade/recovery performance by minimizing entrainment of impurities into the concentrate, which is commonly known since the sixties (Kaya & Laplante, 1989). It has been recommended for the flotation of sulphides and industrial minerals alike (Kaya & Laplante, 1989; Miller, 1969; Heinrich, 1989) and has found its ultimate application in flotation columns (Finch & Dobby, 1990). The washwater addition in a flotation column is most evenly distributed over the column's cross-sectional area thus ensuring almost complete displacement of feed water from the froth by a countercurrent washwater flow -provided, a positive bias is maintained. Therefore, flotation columns are ideal for cleaning flotation. However, there is usually less room for boosting the concentrate production capacity by increasing airflow or slurry level then with conventional cells because of the smaller cross-sectional area available."

Jan 1, 1994

By P. R. G. Brandão, E. E. Ferreira

The presence of metallic cations in solution will affect the aggregation or dispersion of the fine hematite particles, depending on the type of cation adsorption: either specific or non specific adsorption. In this work, the zeta potential measurements were carried out on a sample of pure hematite as a function of pH and metallic cations concentration (Ca2, Mg2+, Mn2+, K+, Na+ and Al3+). The objective of these studies was to clarify the effect of these metallic cations on the surface chemical properties of pure hematite. The cations K+ and Na+ adsorbed as non-specific species and caused only the reduction on the values of zeta potential (in terms of absolute value) over the entire range of pH values tested. For the Al3+ cation, in the acidic pH range it adsorbed as a specific species and increased the zeta potential values. The cations Ca2+, Mg2+ and Mn2+, adsorbed as a non specific species at pH levels less than 6.0 and caused the reduction of zeta potential due to the compression of the electrical double layer. However, for pH values greater than 6.0, these cations adsorbed as a specific species causing the zeta potential to increase and became more positive as the pH value increased (alkaline). This effect could be due to the adsorption of some hidroxy complex species of these cations, which contributed to the positive charge. The effect of metallic cations (Ca2+, Mg2+ and Al3+ concentration, at pH 4.0, 7.0 and 10, showed the following results: a) at pH 4.0, increasing the concentrations of Ca2+ and Mg2+ resulted in on a small reduction in the value of the zeta potential. At this pH, increasing the concentration of A131 cations caused the zeta potential to increase due to specific adsorption of a negatively charged Al3+ hydroxy complex b) at pH 7 and 10, increasing the concentrations of Ca2+ and Mg2+ caused the zeta potential to change its charge from negative to positive.

Jan 1, 2004

By A. Alfantazi, L. Choudhary

Gold leaching in thiosulfate solution has attracted widespread research interest through the last two decades primarily due to its perceived environmental benefits in comparison to the conventional gold cyanidation technique. However, the data on the corrosion and/or corrosion-induced failures of plant infrastructure materials in the solutions relevant to thiosulfate gold leaching are very limited. Accordingly, this study aims to characterize the electrochemical corrosion behavior of stainless steel 316L in the thiosulfate gold leaching solutions. Electrochemical corrosion response was investigated using potentiodynamic polarization and electrochemical impedance spectroscopy. The morphology of corroded specimens was analyzed using scanning electron microscopy.

Jan 1, 2014

By Guoxiang Chi

Hydrocarbon fluid inclusions entrapped in diagenetic minerals may be used to constrain hydrocarbon exploration models in two aspects. First, the distribution of different types of hydrocarbon inclusions in different tectonostratigraphic domains, and their relationships with organic matter maturation levels may reflect a regionalscale variation in the thermal regimes of the hydrocarbon systems. Second, the relative timing of hydrocarbon inclusions in the diagenetic history may provide constraints on the evaluation of reservoir potential. This paper summarizes the distribution of hydrocarbon inclusions in four different Paleozoic tectonostratigraphic domains in eastern Canada, discusses its implications on hydrocarbon systems in the different domains, and finally provides two examples to show how the relative timing of hydrocarbon inclusions may be used in the evaluation of reservoir potential. Oil inclusions mainly occur in host rocks that are within the oil zone, although some are found in units in the condensate zone. Light hydrocarbon inclusions occur in the dry gas zone, and methane inclusions were found from dry gas zone to anchimetamorphism zone. This correlation between hydrocarbon inclusions and host rock maturation implies that the hydrocarbons were derived from source rocks having a maturation level broadly similar to the host rocks. Although the Paleozoic rocks are generally relatively poor in reservoir quality, the two examples provided in this paper show that in some stratigraphic units, significant secondary porosities could have existed prior to some hydrocarbon migration events, thus favoring the accumulation of hydrocarbons.

May 1, 2001

By H. Nejati

Experimentally, the Semi-Circular Bending Moment (SCB) fracture toughness test results of Basalt Specimens Under Illumination (BSUI) have shown reduction in fracture toughness and failure force as a result of micro-cracking. The fractographic investigation of BSUI confirms initiation and extension of micro-cracks. Determination of a relation between strength reduction (herein fracture toughness reduction) and density, location and orientation of thermo-mechanical induced cracks due to microwave radiation is critically important. Numerical modeling can bridge strength reduction and the density of thermal microcracks generated due to microwave radiation. Discrete Element Modeling (DEM) is a power tool for simulation of micro-crack initiation, coalescence into macroscopic fractures and failure mechanisms in brittle rock specimens under different stress regimes (herein combination of pure tensile stress due to SCB testing, and thermal stress due to microwave radiation). For this purpose, a DEM modeling of SCB testing of basalt using EDEM (i.e., a DEM based software). DEM models are calibrated according to results of experimental SCB testing as reported in previous papers. This paper first reviews some background data on SCB fracture toughness, and experimental results of fracture toughness of microwave treated SCBs. Then it proposes a new methodology for simulation and validation of rock samples exposed to microwave illumination with regard to experimental results, and discusses the correlation between fracture toughness of BSUIs and density of micro-cracks, which is attributed to applied microwave power and duration of illumination.

Aug 1, 2013

By W. Basuki, B. Setyotomo, L. Hakim, R. Hendrajaya

Due to high crack sensitivity of slab product of gas and oil line pipe application, its steel making process and alloy composition were evaluated and then improved to overcome its critical solidification process and reduced surface defects. The study was conducted at Slab Steel Plant Krakatau Steel. The purpose was to improve slab surface quality by reducing surface defects so that the slab surface doesn't need to be totally repaired. The method applied was by performing plant trial process, which the secondary process parameters such as alloying method and the casting parameters such as casting powder selection, metallurgical cooling, mould level control, and superheat were continuously monitored and then adjusted to the surface quality of the product. Based on the calculation of Ferrite potential of the steel, the chemical composition was designed to achieve optimum casting parameters in order to avoid high shrinkage during solidification. The results of the study are decreased surface defect quantity, and smooth casting process. The quantity of crack decreased by almost 90%. The slab surface repairing was significantly reduced from 85. % to less than 10%. These new casting parameters and developed alloy composition are then used and standardized for the mass production of the steel.

Jan 1, 2005

By C. Díaz, A. D. Dalvi, C. E. O'Neill

Roast-reduction smelting (RRS) of nickel concentrate, combined with flash smelting of copper concentrate, was one of the process options that Inco considered as a means of meeting its 1994 sulphur dioxide abatement target at its Copper Cliff operations. RRS involves deep roasting the nickel concentrate in fluid bed roasters. The roaster off-gas is treated in a sulphuric acid plant, and the low sulphur calcine is reduction smelted with coke in an electric furnace to yield a sulphur- deficient matte. The latter material is converted to Bessemer matte in Peirce-Smith converters, with minimal evolution of sulphur dioxide, and the converter slag is reverted to the electric furnace. Excellent nickel and cobalt recoveries (Ire obtained. This paper discusses the development of RRS, including extensive commercial scale testing at Inco's Thompson Smelter, and its key operating parameters.

Jan 1, 1994

By Rodrigo Madariaga, Tracy T. Morris

The practice of stripping copper starter sheets from titanium blanks to be used in a conventional electrolytic tankhouse has been around since the advent of Electrometallurgy. Historically it has been done manually, utilizing many people to produce in some cases thousands of starter sheets per day. Some other conventional tankhouses have successfully converted to using mechanical means to strip starter sheets or have made the switch to permanent cathodes and although robotics have been around for quite some time they have not been used to strip starter sheets until recently. The Amarillo Copper Refinery began using robotics to strip several years ago and the details to how this came about and how the robots work will be described. INTRODUCTION ASARCO LLC (Asarco) was organized in 1899 as the American Smelting and Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co- products (Marcosson, 1949). Grupo México, S.A.B. de C.V acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, molybdenum, selenium and tellurium. Asarco operates three open-pit mines and mills and two solvent extraction-electrowinning (SX-EW) plants all in Arizona plus a copper smelter in Arizona and a copper refinery in Texas. Figure 1 illustrates how the copper metal comes out of the ground at the mine and ends up as a refined product at the refinery The copper refinery in Texas is known as the Amarillo Copper Refinery (ACR) and is located in Amarillo, Texas. It was built in 1975 to replace 3 other aging refineries and was designed to produce 550,000 tons (500,000 MT) of refined copper per year using conventional starter sheet technology. At the time it was commissioned it was the largest tankhouse in the world at just under 1/2 miles long under one roof.

Jan 1, 2019

By S. A. Kenzap

This paper provides an overview and discussion of key aspects of operating risk valuation in underground metal mining systems, with impact on project economics, using stochastic computer modelling in Discounted Cash Flow (DCF) analysis. Mine operating risk classification and assessment for ground, equipment and scheduling aspects are presented with an overview of available risk valuation tools that have been developed in engineering disciplines. The classification is organized by keeping in perspective the mine design needs and constraints, as well as the potential economic impact that operating problems can have on an underground development and production system. These sources of cost, revenue and time delays are tabulated to enable the hierarchization of potentially hazardous unplanned events occurring during the mining project life cycle. In complex technological systems, like the underground mining systems, the decision-making process involve a wide range of uncertainties, and often this is based on subjective and qualitative expert evaluations. Whether a qualitative or quantitative analysis is conducted, it is often the case that the probability of a certain project parameter value needs to be estimated. This requires use of methods and techniques to handle subjective, qualitative measures and to combine them with quantitative stochastic modelling in order to evaluate mine operations-related issues on DCF economic performance measure parameters. Links are established between decision making and the risk-based mine planning process for evaluation of design alternatives, with emphasis on the need of introducing flexibility in mine design. Finally, challenges of risk-based mine planning and design implementations are discussed and the call for an integrated risk-based real options systems valuation (ROV) ?in? projects analysis is made.

Aug 1, 2013

By Ning Yu

There are about 1.341 trillion tons (t) of proven coal reserves in China, of which 279.58 billion t are available for mine well construction basis. Thick coal seams are 44% of the reserves. The production of thick coal seams exploitation is over 45% of the total coal production. Full-seam mining and fully-mechanized mining for large mining height is the technology development direction of thick and extra thick seam mining. It is also the important way to achieve efficient and intensive mining with the characteristics of high production, high mechanization, high efficiency and low energy consumption, etc. Complete set of technology and equipment of fully-mechanized top caving for large mining height of full-seam (7m) mining and extra thick seam ( 14-20m) has been gradually mature and for demonstration application by the joint research of government, enterprises, universities, scientific research organizations and users. It has solved some technical problems of coal face for large mining height (over 7m) such as the coal wall spalling control, stability of support, wall rock coupling, cooperation work of mining and caving, full roadway support for super large section, end support, equipment matching of coal shearers, hydraulic support and scraper conveyor. It has developed key equipments including powerful hydraulic support of fully-mechanized mining and fully-mechanized top caving for large mining height, electrically-driven coal shearer with high speed and reliability, scraper and belt conveyer with big capacity, soft-start and high reliability, automatic control system of coal face with the core of electric-hydraulic control, bolting drill boom large section coal roadway shearer, heavy auxiliary transport equipment. The operation rates of fully-mechanized top caving equipment for full-seam and large mining height are 94% and 92.1%, and recovery ratios are 93.6% and 88.9% respectively. The annual raw coal production of single work face is over 10 Mt. The automation and intelligentization level have been clearly improved. The exploitation of thick and extra thick coal seam that is safe and efficient has been achieved in China.

Aug 1, 2013

By M. S. Moats, F. Elnathan

"The effect of current reversal on two commercially manufactured electrodes (RuO2-TiO2 and IrO2-Ta2O5 coated Ti) in a chloride bearing electrolyte was evaluated. Accelerated lifetimes were found to decrease with increasing current density and increasing reversal frequency. Ru: Ti coated electrodes exhibited longer lifetimes than Ir: Ta coated electrodes even though they had one-third as much precious metal content. Chloride concentration did not affect lifetime in the range examined. Using energy dispersive X-ray spectroscopy (EDS), scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS), the failure mode of the electrodes was determined to be coating dissolution leading ultimately to passivation by the presumed growth of a highly resistive oxide at the coating/substrate interface.INTRODUCTIONCatalytic titanium anodes (CTAs) were developed in the 1960’s to replace graphite anodes in chlor-alkali cells. CTAs exhibited much better dimensional stability than graphite leading to lower operating potentials by promoting smaller electrode gaps and better operational efficiencies as they had to be replaced less often. CTAs are simply Ti substrates coated with precious metal oxides (such as IrO2 and RuO2) mixed with other components (such as TiO2 and TasO5) (Trasatti, 2000).CTAs are used in many other electrochemical industries, including water disinfection, wastewater treatment, cathodic protection and metal plating. RuO2 based coatings are typically used for chlorine evolution. IrO2 based coatings are for the most part utilized for oxygen evolution (Comninellis & Nerini, 1991; Forti, Olive, & De Andrade, 2001; Kotz, Stucki & Carcer, 1991; Trasatti & Lodi, 1981)"

Jan 1, 2016

By Ahmad Ghahremaninezhad, Noelene Ahern, Yeonuk Choi

Arsenic (As) is a toxic element and is a major contaminant in the extraction processes of some metals (e.g. gold and copper). Due to the toxicity of arsenic species, its removal from As-containing streams from extractive metallurgy processes and safe disposal is absolutely necessary. For nearly complete removal of waste arsenic species from metallurgical process streams, it is required to have arsenic in its pentavalent state (As5+ species). This study presents an oxidation process for arsenic species with air or oxygen gas as oxidant. Activated carbon (AC) or other carbon based materials are used to catalyse the oxidation reaction. Air or oxygen gas is the only consumed reagent which makes the economy of the process very attractive. The oxidation reaction can be carried out at ambient conditions (room temperature and atmospheric pressure) in less than 24 hours.

Jan 1, 2014

By Sean Dessureault

Technological Revolution ?Information age ? brought about by: ?Low-cost processing, storage, information sharing ?Shared & integrated data ? Increasingly more sensors & data sources From data collection to data use ??Data mining??analyzing the huge volumes of data ?Key example used in MBAs: ?Wal-mart, Google Explosion of data, trickle of information ?Paralysis of action Outline Trying to provoke- What drives innovation now? ?Challenges in mining Data Action Approach ?Examples from research & consulting upon request Conclusions ?Unaddressed challenges (Research Opportunities)

May 1, 2006

By V. Cvetkovic, L. Zou, L. Jing

"Sorption process plays a significant role for solute retardation in rock fractures. In this paper, for the aim to investigate the effect of sorption on solute transport in a single rough fracture, a 2D model of representative single rock fracture was built and its roughness was statistically characterized based on the measured data of rock surface topography by laser scanning. A Finite Volume Method (FVM) code was developed to solve the Navier-Stokes (NS) equations and transport equation for numerical modelling the process of fluid flow and solute transport in the rock fracture model. Two groups of simulations were conducted: with and without the consideration of the sorption process with different average flow velocities. The results show that the surface roughness increased the complexities of flow fields, and the non-linear sorption process plays a significant role in the retardation of solute transport through rock fractures. The sorption process caused an obvious lagging time in both the solute concentration fields (plumes) and corresponding breakthrough curves. This lagging time increases with the distance from the inlet boundary, and relatively decreases with the increase of mean velocities. INTRODUCTIONFluid flow and solute transport in fractured rocks is an important research topic for performance and risk assessments for rock engineering projects concerning geo-environment safety, such as radioactive waste disposal, mining, geothermal extraction, reservoir engineering and other contaminant transport processes in geosphere (Berkowitz 2002).The solute transport in the rock fractures mainly involve the advection, surface sorption, matrix diffusion, dispersion, radioactive decay and chemical reactions, governed by general transport equations (e.g. Bodin et al., 2003). Among these transport phenomena, the sorption on the fracture walls can alter solute migration between the fractures, and play an important role in natural retention of solute transport (Weber et al., 1991; Wels et al., 1998; Kumar 2007; Dai et al., 2012). The aim of this study is to investigate the effect of sorption on the solute transport in a single rock fracture with rough surfaces. More complex transport processes, such as matrix diffusion, dispersions, radioactive decay and chemical reactions, are not included in this study."

Jan 1, 2015

By J. J. Barakso, S. J. Horsky, H. V. Warren

"A review of past and present biogeochemical studies is given. Early and more recent analytical procedures are described and compared. Tables 1-5 give silver concentrations in various organs of some plant species at different localities. Table 6 and conclusions provide guidelines for exploring for silver using biogeochemistry.IntroductionBiogeochemistry has been shown to be a useful tool in the search for gold deposits, especially those of the disseminated type (Warren and Barakso 1982). The purpose of this paper is to demonstrate that biogeochemistry can also be of assistance in searching for silver concentrations buried by as much as twenty feet of overburden without inflicting any damage on the environment."

Jan 1, 1984

By A. Mellek, M. Pischtschan, M. Perrucci

ABB has received an order for one of the most challenging mill drive projects in its history. With one SAG mill and one ball mill to be added at an iron ore mine in Sweden, the customer’s plant managers wanted to have the most efficient solution for driving their mills but had the budget limitations typically faced by the majority of mining companies during periods of market downturn. To find the best balance between cost of acquisition and highest performance throughout the lifetime of the plant, ABB was selected to deploy a synchronized bypass solution, in which only one drive system is used for two different mills in series. However, being one of the first grinding mills in the world with such a solution was not the only challenge the ABB team faced: The inclusion of some mill application functions - e.g., frozen charge protection, automatic positioning and creeping mode - brought the demands on the engineers to another level. With only one frequency converter and one mill application controller available, the configuration logic and interlocks had to be meticulously designed and thoroughly tested to ensure a smooth and safe startup. The solution offers a footprint reduction and more operator flexibility at a reduced investment as each mill can be run in both directions, and wear on the mechanical components can be greatly reduced due to ABB’s premium ring-geared mill drive (RMD). This paper will describe the details of the project, the configuration developed and the tests performed to guarantee correct software functionality. Mill startup is scheduled for January 2016.

Jan 1, 2016

By Stephen Mcgibbon, Tim Twomey

"Abstract - The High-grade Zone (HGZ) was discovered 5000 ft (1520 m) below surface in the hangingwall of the existing orebody, 46 years after the Red Lake mine first went into production. The very rich ore of the HGZ is characterized by a remarkably abundant distribution of visible native gold. The location of this discovery challenged conventional wisdom at the time and its genesis has yet to be fully understood. Textural observations of ore within carbonate veins as well as crosscutting relationships suggest peak-metamorphic emplacement for at least some of the gold. Post-lamprophyre dike remobilization of gold is locally observed in the HGZ. Structure and dilatancy were the key elements for localizing ore at the Red Lake mine. Ore occurs where a fault trend intersected folded ultramafic volcanic rock that created a semi-permeable cap-rock to ore fluids ascending the "feeder" structure. This was enhanced by strong competency contrasts between the eastern ultramafic rocks, felsic volcanic rocks west of the HGZ, and the mafic volcanic host to ore - an exceptional environment for the development of protracted dilatant fluid pathways for gold deposition.Development in the HGZ began in February 2000 and reached commercial production on January 1, 2001 at a capital cost of US $53 million. December 2001 reserves are 1.9 million short tons (1.73 Mt) at an average cut and diluted grade of 2.05 ounces per ton gold (70.5 g/t) containing 3.8 million ounces of gold. The extremely rich ore presented a unique challenge in grade estimation for the Geology Department at the mine. The historic cutting factor was replaced by a statistical method as more data were collected from mining and mill reconciliation. The mine produced 503 000 ounces of gold in 2001. Exploration at the mine is targeting HGZ-type ore formation within basalts associated with the intersections of fluid pathways and folded ultramafic rocks, as well as other targets."

Jan 1, 2001

By C. Díaz, A. D. Dalvi, C. E. O'Neill

"Roast-reduction smelting (RRS) of nickel concentrate, combined with flash smelting of copper concentrate, was one of the process options that Inco considered as a means of meeting its 1994 sulphur dioxide abatement target at its Copper Cliff operations. RRS involves deep roasting the nickel concentrate in fluid bed roasters. The roaster off-gas is treated in a sulphuric acid plant, and the low sulphur calcine is reduction smelted with coke in an electric furnace to yield a sulphur-deficient matte. The latter material is converted to Bessemer matte in Peirce-Smith converters, with minimal evolution of sulphur dioxide, and the converter slag is reverted to the electric furnace. Excellent nickel and cobalt recoveries (Ire obtained. This paper discusses the development of RRS, including extensive commercial scale testing at Inco's Thompson Smelter, and its key operating parameters. IntroductionReduction of sulphur dioxide emissions has been a long-standing endeavour at Inco. At the company's Ontario Division, as shown in Figure 1, sulphur dioxide emissions were reduced from about 2 million to 685 000 tonnes per year over the period 1970-1985. Most of this impressive improvement was the result of a sustained research effort which led to increased rejection of pyrrhotite from the ore during milling while maintaining an acceptable nickel recovery. Between 1970 and 1985, the combined grade of the separate nickel and copper concentrates feeding the Copper Cliff Smelter increased from about 10070 to about 'lIJ0J0 Cu +Ni and the combined S/(CU +Ni) ratio decreased from about 2.8 to 1.65."

Jan 1, 1994

By T. Bhambhani, O. Yavuzkan, D. R. Nagaraj

"Cu ore bodies commonly contain oxide Cu at the surface, with sulfide Cu content increasing with depth. The recovery of oxide Cu minerals by flotation is a longstanding challenge in the minerals industry, especially for high acid-consuming ores which would not be economical for direct acid leaching. Current practice of oxide Cu recovery involves sulfidization (often using controlled potential sulfidization or CPS) using NaSH (or Na2S) followed by flotation using traditional sulfide collectors. CPS has shown to improve recovery of oxide Cu but has the following limitations: a) HSE issues with NaSH, b) high consumption of NaSH, and c) inability to recover certain oxide Cu minerals because they are refractory to sulfidization. The oxide Cu flotation is further complicated by the presence of certain non-sulfide gangue minerals which adversely impact both recovery and selectivity.Over the past eight decades, numerous collectors have been proposed and evaluated for the direct flotation (i.e. without sulfidization) of oxide Cu minerals, the most researched of which is alkyl hydroxamate. While there are numerous publications dealing with the fundamentals of interaction of alkyl hydroxamates with single minerals, there are few publications which discuss the practical aspects of alkyl hydroxamate use in ore flotation, particularly their use with sulfidizing agents. Case studies in this paper include methods to identify optimum combinations of sulfidizing agents and oxide collectors to maximize recovery for various types of ores. It was observed that some ores do not require any sulfidization, while others require at least partial sulfidization to improve efficacy of AHX. Depending upon the ore type and mineralogy, recovery improvement in the range of 5 to 15% units, over and above that achieved with CPS, has been observed with the use of AHX. For ores requiring high dosages of NaSH, it was shown that AHX can be used to reduce the NaSH consumption significantly. The challenges associated with the presence of non-sulfide gangue minerals in oxide copper ores are included, and the use of modifiers to alleviate the associated problems and enhance the performance of AHX is discussed."

Jan 1, 2016

By D. H. Whiting, A. J. Sinclair

"The San Antonio gold mine, in the Archean Rice Lake Greenstone Belt, was in continuous production from 1932 to 1968, during which period the mine yielded 1.35 million ounces (41 985 kg) of gold and 195,000 ounces (6065 kg) of silver from 4.88 million tons (4.44 Mt) of ore for average grades of 0.28 ounces per ton (9.0 g/t) gold and 0.04 ounces per ton (1.3 g/t) silver. After the 1968 closure, several publications appeared implying that gold grade of ore decreased with increasing depth.Recent observations by the authors show that the relatively low grades in the middle levels of the mine are controlled geologically. However, the reduced average are grade in the lower levels of the mine was due to inadequate mining control that led to a high level of dilution. The similarity of geological factors such as vein styles within structural domains, variations in mining control, recent ore muck sampling results and lithogeo chemical profiles all indicate the similarity of ore in both upper and lower levels.Strict mining control should yield improved grades of gold for future production from the lower levels at San Antonio, in contrast with the production grades of the late 19605that represented extensively diluted ore. High-quality production records are an essential component in re-evaluating a past producer, particularly where workings are accessible. Poorly founded conclusions which cannot be checked by access to workings can have a negative impact on the evaluation procedure."

Jan 1, 1990