Search Documents

Precast prestressed concrete piles designed to be end-bearing in a sand stratum at Drax Power Station met with extremely variable resistance during driving. Some piles came to virtual refusal almost immediately on entering the sand whereas others were driven to considerable penetration with very low resistance. Redriving and load tests on piles experiencing low resistance on initial drive showed that take up in strength occurred over a relatively short period of time. Investigations involving the use of pneumatic piezometers revealed the development of significant excess pore pressures during driving. Samples from boreholes showed that piles met the least resistance when the sand had a high silt content. Comparison with the original site investigation data demonstrated the difficulties in predicting detailed pile behaviour. The varied behaviour could not be related to the original borehole logs or to SPT or static cone penetrometer results. The factors controlling pile driving behaviour were essentially geological and could only be explained with reference to local soil grading.

Jan 1, 1989

By Kirk A. Mcintosh

Augered, cast-in-place (ACIP) piles have been utilized in the United States for a wide range of projects since the 1950's. Due to the cast-in-place nature of the installation method (and lack of a driving criteria); however, ACIP piles have not been readily accepted by some practicing geotechnical and structural engineers. Since ACIP piles were initially developed, the installation equipment and techniques have been improved and refined and the number of experienced contractors has significantly increased. Over the past 10 to 15 years, the pile type has experienced significant growth in the United States (particularly in Florida) because engineers have become more knowledgeable and comfortable with its use. The Miami area, in particular, has experienced considerable growth in the utilization of ACIP piles primarily due to their usage on the $1 billion Miami Metrorail System project in the early 1980s. The economic advantages over other deep foundation types, coupled with some unique installation advantages, have shown that ACIP piles can be a viable foundation alternative on many projects. Even though ACIP piles have gained respect in the private sector, the pile type has generally not been readily accepted by government transportation agencies. The reluctance to readily accept this foundation type stems primarily from the quality assurance aspect of cast-in-place pile construction. Additionally, there has not been much research activity on this foundation type, technical papers, formal associations (other than the DFI), or a concerted effort to standardize the industry. This paper serves to discuss the state of practice for ACIP pile installation in the state of Florida.

Jan 1, 1997

By James S. Graham

Research at the University of Colorado on southern pine and Douglas-fir piling has determined that the existing building code design stress values of 1200 psi and 1250 psi, as determined by ASTM D-2899, are substantiated; but testing procedures should be revised. All full size piling tests should be standardized at 1/d ratios of 2:1, or confined tests performed. Also, it has been determined that theoretical design values for timber piling should not be based on the lumber criteria of D-245 and D-2555, but instead should follow the pattern set by engineers in the utility industry for timber poles, in accordance with ANSI 05.1.

Jan 1, 1986

By K. Rainer Massarsch

In some parts of the world, vibrators are used extensively for different types of foundation engineering projects. If used correctly and in suitable soils then vibratory pile driving for example is very efficient. However, soil conditions and the installation procedure have great significance for the driving resistance and affect the bearing capacity of vibrated piles. Also the intensity of ground vibrations which are transmitted to the surrounding soil is affected by the vibration process. In spite of the increasing use of vibrators and the rapid development of vibrator technology, many aspects of pile-soil interaction are not yet understood. In order to asses the importance of factors, which govern pile installation (and extraction), it is necessary to consider the entire chain of vibration energy transmission from the vibration source to the pile, the interaction between the vibrating pile and the soil and the wave propagation in the subsoil, Fig. 1. [ ] Fig. 1. Transfer of vibration energy from the vibrator through the pile into the ground In the present paper, some important aspects of vibratory driving and their significance for pile installation and soil compaction will be discussed.

Jan 1, 1995

By Theodore R. Maynard

The history of foundation engineering in Chicago is a tale of innovation, made necessary in order to keep pace with structural technology which allowed taller buildings with heavier bearing loads, to accommodate a non-conducive geologic setting. The geology as it relates to foundation construction and underground construction in general is briefly described. A chronology of important events from the birth of Chicago to the present is presented. The impact of various construction techniques which were either initiated or refined to allow the growth of Chicago are discussed. Introduction The growth of Chicago resulting in today's high-rise high-density population center can be looked upon as a history of modern underground construction. The two major reasons which explain this are 1) It grew up during a period of rapid development in the Industrial Revolution and 2) Its natural geological setting needed a great deal of innovation for continuing growth.

Jan 1, 1991

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees was applied to a 0.61 m (2 ft) diameter flagpole and a 0.61m (2 ft) diameter fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil was represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2012

By B. Ramanathan

The results of a pile load test on a 1200 mm dia and 25 m long bored Cast-in-situ pile in soft rock is reported. The subsoil has a high N value of above 60 from 7 m to 21 m. The soft rock was observed below 21 m and N value exceeded 100. The theoretical calculations showed that the safe carrying capacity will be about 410 t. But the actual load test on the pile indicated that the allowable load is only about 140 t. This is attributed to the fact that the soil is cemented and loses strength due to remoulding caused by pile installation. It is concluded that great care should be exercised in determining the carrying capacity of piles in cemented soils and soft rocks and that 'N' value alone should not be used.

Jan 1, 1996

By Cory McElprang, Enamul Hoque, Aaron Thomas, Scott A. Jacobs

Crosshole Sonic Logging (CSL) only evaluates concrete on the inside of reinforcing cages leaving the outside unevaluated unless other types of testing are performed such as Perimeter Sonic Logging (PSL). While there have been some reports of PSL testing having accurately identified anomalies (e.g. Samtani et al 2005), experience by Case Foundation Company has indicated otherwise where false positives were determined with subsequent coring. Numerous cases of PSL false positives are presented as well as a study where a shaft was installed with both inside and outside tubes, and CSL and PSL data were compared. To date, there is very limited data published on perimeter sonic logging, or Gamma-Gamma Logging (GGL) with tubes on the exterior of drilled shafts. Several cases will be presented where false positives were experienced where PSL testing was performed. In addition, a direct comparison will also be presented where a shaft was installed with both tubes on the inside and outside where CSL and PSL data is compared. BRIEF HISTORY – CSL TESTING AND TUBES ON INSIDE The general procedure of Crosshole Sonic Logging (CSL) testing includes attaching tubes to the reinforcing cage to be able to send a transmitter in one tube and a receiver in another tube with which a sonic pulse is emitted from the transmitter and received in another tube. The time taken for the sonic pulse to travel between the tubes is measured and compared to expected values for the known distance between the tubes. Any increase in time from expected values indicates the sonic pulse traveled through a media other than homogeneous concrete such as objects in the path (spacer wheels, steel bracing, etc.), tube spacing, or soil inclusions. However, variations in arrival time can also result from differences in concrete density. The tubes have traditionally been placed on the interior of the reinforcing cage which protects them during hoisting and placement of the cage and reduces wave refraction caused by modulus of elasticity differences between steel and concrete. This allows the concrete within the interior of the reinforcing cage to be evaluated, but the concrete outside of the cage is excluded from traditional CSL testing. As a result, alternative integrity testing has been developed to not only provide different ways to evaluate the integrity of drilled shafts but to also address the issue of evaluating the concrete outside of the reinforcing cage. These alternative testing methods include Gamma-Gamma Logging (GGL), Thermal Integrity Profiling (TIP testing) and Perimeter Sonic Logging (PSL) which is similar to CSL testing but instead of the tubes placed inside the reinforcing cage, the tubes are placed on the outside of the reinforcing cage as shown in Fig. 1.

Jan 1, 2019

By Reda M. Bakeer

"An approach slab is the roadway segment that immediately follows a bridge intended to provide a smooth transition between the two elements. Some approach slabs have developed rough rideability with time due to differential settlement between the roadway embankment and the bridge. Soils in south Louisiana are generally poor and highly compressible and, therefore, pile-supported approach slabs were occasionally used. Timber piles of variable lengths are driven into the soft soils where no appreciable toe support exists. This resulted in the soils both supporting loads through shaft resistance and yet experiencing long-term consolidation settlement. Field testing and review of the records of over 120 approach slabs constructed in south Louisiana yielded the conclusion that their performance is primarily governed by negative skin friction (downdrag) imposed on the relatively short timber piles. A software (TU-DRAG) was developed to evaluate the deflection profile of a pile-supported approach slab based on its geometry and conditions of the underlying soils. It evaluates the effect of dragload considering the number and spacing of the piles at each transverse row and their variable lengths along the approach slab. TU-DRAG was utilized in the design of two transportation related projects which have been in service for more than 10 years.INTRODUCTIONThe problem of differential settlement at bridge approaches or “the bump at the bridge” has been recognized for many years. Research studies (1986, 1989, 1997, 2009 and 2013) by the Transportation Research Board (TRB) and the Federal Highway Administration (FHWA) provided comprehensive evaluations of the performance of bridge approach slabs by assessing their field conditions and construction and maintenance records. Various states have also performed their own studies to investigate the performance of bridge approach slabs. The studies considered various types of structures including soil- and pile-supported approach slabs, integral bridge abutments and open-end abutments. Recommendations were provided for the design of new structures and for maintaining and repairing existing structures. Guidelines were offered regarding tolerable movements of bridges and their foundations based on measurements of vertical and horizontal movements of 580 bridges Moulton (1986). Vertical and horizontal movements greater than 102 mm (4 inches) and 51 mm (2 inches), respectively, were considered intolerable. Tolerable limits for angular distortion (differential settlement to span length) were suggested to be 1/250 and 1/200 for continuous and simple spans, respectively. It was reported that a differential settlement greater than 13 mm (0.5 inch) at the bridge interface would be sufficient to constitute a “bump” requiring mitigation."

Jan 1, 2017

By P. B. Kelleher

Most of the piers and other pile-supported marine structures in the New York City Harbor area were constructed prior to the widespread use of currently available pile protective systems. As a result, the support piling of many existing marine structures have experienced deterioration to an extent that their structural sufficiency is impaired long before the useful life of the structures they support is over. This situation presents special and unique problems of how to restore the structural integrity of these piles while at the same time allowing full use of the structures they support. Spearin, Preston & Burrows is a 100 year old New York City-based marine construction firm specializing in waterfront and foundation construction. In recent years it has undertaken and successfully completed several unusual projects in the New York City Harbor area involving the rehabilitation of existing, deteriorated piling underneath major, economically important marine structures. This work was accomplished using techniques that permitted full use of these structures. Several different pile rehabilitation systems were used, each having their own particular application to the deterioration problems of the piles supporting each structure.

Jan 1, 1989

By Scott C. Vollmer

This paper seeks to examine some of the technical factors influencing the deflection of Mechanically Stabilized Earth (MSE) retaining walls based on the authors' field observation of numerous structures. Excessive deflections can be unsightly and can be perceived as wall failure. Deflections can cause cracking or gapping of the facing units and general misalignment. Deflection of the reinforced backfill zone behind the wall face can result in settlement of the backfill zone and adjacent pavement cracking. Deflections can be the result of excessive movement external or internal to the reinforced soil structure. This paper only examines internal factors affecting wall deflections. External factors such as foundation settlement are not discussed.

Jan 1, 2003

By Timothy L. Roberts

For many years practicing geotechnical and structural engineers in Texas and Louisiana were reluctant to include augered cast-in-place (ACIP) piles as a viable deep foundation alternate. Three primary concerns were the lack of a final driving resistance to confirm adequate capacity, the inability to inspect ACIP piles prior to installation, and the fact that pile integrity is highly dependent on the skill of the ACIP pile contractor's field personnel. The Deep Foundations Institute (DFI) Committee on Augered Cast-In-Place Piles has responded to these quality control concerns by establishing standards of practice for ACIP pile installation and ACIP pile inspection. Regional areas of the country have different subsurface soil and rock conditions and many times this will influence local installation and inspection requirements. The best way structural and geotechnical engineers can address quality control concerns is to be familiar with the DFI standards of practice, to know the special requirements for a particular project site, and to incorporate them into a well-written ACIP pile specification. The purposes of this paper are to: 1) review the main fundamentals of a successful quality control program, 2) describe how these fundamentals can be applied to the installation of ACIP piles, and 3) add personal experiences from ACIP pile projects in Texas and Louisiana. Nondestructive test methods are frequently used as a quality control tool to evaluate questionable piles. An additional brief discussion of two nondestructive test methods is presented to complete the paper.

Jan 1, 1998

By Ian Vaz, Takefumi Takuma

"The New Orleans area has been repeatedly flooded by major storms and hurricanes since its French colonial era. After severe flooding in May 1995, the U.S. Congress authorized a massive flood protection project called the Southeast Louisiana Urban Flood Control Program (SELA) in 1996 to improve interior drainage in Orleans, Jefferson, and St. Tammany parishes. However, the project was not fully funded before the landing of Hurricane Katrina in 2005 and Hurricane Rita, which breached many of the area’s levees and flooded 80 percent of the city. Finally, the project was fully funded in 2008 and has been worked on towards its 2017 completion. Another large project simultaneously worked on in the area is the Hurricane and Storm Damage Risk Reduction System (HSDRRS). This system was designed for a 100-year level of flood risk reduction. One particular project within the HSDRRS rendered successful due to an unconventional method of pile driving that was utilized to install sheet piles to reinforce an existing concrete I-wall. This paper will discuss how and why this non-vibratory method of sheet pile installation allowed the project to be successfully completed ahead of schedule.INTRODUCTIONSteel sheet piles were utilized on many of the SELA and HSDRRS projects for permanent cutoff walls under concrete I-walls or T-walls or for temporary earth retaining walls of drainage structures. Although the SELA Project was established in 1996 after severe flooding the year before, hardly any work was done on it until the two catastrophic storms Hurricanes known as Katrina and Rita triggered its revival. These two hurricanes also triggered the HSDRRS soon after the storms’ devastation. The SELA project authorized to improve interior drainage systems while the HSDRRS project was authorized to raise or restore levees and floodwalls mainly along Lake Pontchartrain, the Mississippi River, and Lake Borgne in addition to other areas. Figure 1 shows the SELA Projects that have been completed, are still under construction, or approved for construction. The projects fully highlighted in yellow within the map specified the press-in piling method. These improvements included drainage systems, pump stations, surge walls, and outfall canals as enhanced protection for future storms similar to Hurricane Katrina that caused so much damage by inundating the New Orleans area in August and September 2005 respectively (Facts and Figures, 2012). The completion of these projects were the responsibility of the U.S. Army Corps of Engineers, New Orleans District.Due to the fact that many of the projects were in densely populated areas, the Army Corps of Engineers specified a non-impact, non-vibratory press-in piling method for driving and extracting sheet piles for many of the projects to mitigate noise and vibration impacts. The soft soil conditions in the New Orleans area was also a contributing factor in the Army Corps of Engineers’ decision to specify this piling method due to the risk of settlement for existing historical as well as modern structures. In addition, there were other projects that elected to use the press-in method without any contractual requirements. One of these projects was the Inner Harbor Navigational Canal Reach II Emergency Interim Repair which was part of the HSDRRS project that has been under construction since its authorization in 2005 (Facts and Figures, 2012)."

Jan 1, 2017

By A. Fisher

The use of thermal integrity testing to verify the quality of deep foundations has increased significantly in the UK and other world markets over the last 5 years. The introduction of distributed fibre optic sensing to this field has broadened the range of applications in which it can be deployed and the types of foundations which can be tested. This paper presents how fibre optic sensing technology can be successfully deployed in the construction environment the range of foundation techniques to which it can be applied. Alongside developments in the practical aspects of thermal testing, progress has been made in establishing assessment criteria which can be used to evaluate the results. This paper presents recent examples of comparative studies on foundations which include both thermal integrity testing, cross hole sonic logging and intrusive coring. The use of distributed strain measurement during pile load testing presents an alternative means to verify the assessment criteria used for integrity testing. This new approach can achieve comparable results to foundation exhumation or intrusive investigation and at a fraction of the cost. This paper presents the findings of several such studies, highlighting the benefits and opportunities for future improvement of the method.

Oct 1, 2022

By Nagarajkumar BV

Pavai-and TeampT JV started working on the project T49A, Sumbar J & K State as part of slope and earth stabilization for ongoing Banihal - Katra Railway Connection Project. This project has several tunnels and bridges with slopes that are protected with various types of protection system such rock bolting, rock anchors, and micro piles. For the main two bridges Bring number 2 and 3 at T49 A location Pavai - TeampT JV has to design and execute the circular group of micro piles (Fig.1) for deep excavation of earth for the purpose of construction of well foundations (CAISSON FOUNDATIONS) for both bridge 2 and 3 piers. In this paper we discuss about the purpose, basic design, detailed design approaches and actual work implementation of micro pile with composite rock bolt applications and permanent rock anchors for slope stabilization works in this project.

Nov 1, 2022

By Anil Bhandari

Using subsurface data collected at each drilled shaft location is an ideal approach for conducting drilled shaft design. However, conducting subsurface tests at each drilled shaft location and subsequently performing the drilled shaft design can be a daunting task for a noise barrier wall that is divided into six (6) sections and stretches for approximately four (4) miles. In addition, having individual drilled shaft designs complicates the construction process. Grouping the subsurface conditions into broad categories and performing the design for each of those categories is an attractive alternative to the design per boring approach. Currently there are no existing guidelines to aid a designer on grouping the subsurface conditions for the drilled shaft design for the noise barrier walls. Therefore, a method was developed based on the Standard Penetration Test (SPT) N values of the near surface soils to categorize the soil profiles into distinct categories. Since the soil engineering properties of the near surface soils are known to be critical for drilled shaft lateral capacity, these soils were emphasized in the methodology. This method was successfully implemented for the design of drilled shafts supporting the noise barrier walls along the I-20 in Columbia, SC. For this project, two distinct soil profiles, labeled as ?strong? and ?weak?, were used. An overview of the soil profile grouping methodology is presented as well as the vertical and lateral drilled shaft capacity analyses for this project for the two general soil profiles. The analyses indicated that the axial capacity governed the design in the ?weak? soil profile and the lateral capacity controlled the design in the ?strong? soil profile. However, this is not a generalization and whether the axial or the lateral capacity governs the design of drilled shaft depends on the soil profile and design loads. Nonetheless, our findings emphasize that both lateral and axial capacity should be checked for drilled shaft design even when the vertical load are minor.

Jan 1, 2011

By Masaki Kitazume

Deep mixing method, in-situ admixture stabilization technique, has been developed and adopted for on land and marine construction works in Japan. The geotechnical design procedure of the method has been standardized in Ministry of Land, Infrastructure and Transport Government of Japan for port and harbor facilities, which includes the block type and wall type improved grounds for foundation stability, settlement reduction purpose. This procedure is based on the allowable stress concept, in which the induced stresses within the improved ground are confirmed to be lower than the allowable strength in the internal stability calculation. This procedure has been cited by several organizations to establish their standards. The Ministry has a plan to introduce a reliability based design for marine construction works in 2006, in which the design procedure on DM improved ground will also be modified to the reliability based. In the new design procedure, the average and variation of soil parameters and external loads are incorporated by partial safety factors to investigate the stability of improved ground. According to the plan, the author has been studied the design procedure and the magnitude of partial safety factors, and has established a preliminary draft of the standard. This draft will be brushed up through comparing the current design procedure. In this article, the design concept and design procedure of the method are briefly described.

Jan 1, 2004

By Michael W. Neill, O&apos

Drilling slurry has become an effective aid to the construction of drilled shafts in caving and/or waterbearing soils. Historically, drilling slurry made of bentonitic clay and water was first used in the US in water well drilling as early as 1889. In coastal Texas drilled shaft contractors began using slurry, often made of on-site clay mixed with potable water, in the years following World War II, on a relatively routine basis. This type of slurry was used to "process" boreholes, in which the borehole was drilled "in the dry" until water or unstable soil was encountered, after which water and on-site clay were introduced into the borehole and mixed in place with the auger or other drilling tool. Drilling then continued under a slurry consisting of the uncontrolled mixture of clay and water until the excavation had reached a relatively impermeable and cohesive material. At this point, a steel casing was dropped into the hole and sealed into the lower stratum of impermeable geomaterial (soil or rock). The slurry inside the casing was bailed or pumped out, drilling continued to plan depth in the dry, a reinforcing cage was set in the partially cased borehole, concrete was placed and the casing was withdrawn. Some soil-slurry was undoubtedly trapped between the casing and the borehole wall, but the quality of that slurry was usually of no concern, because engineers of the period usually viewed drilled shafts as nothing more than deeply buried footings. Any unejected slurry would only serve to lower side shearing resistance, not yet considered in design, but would have no effect on end bearing. In the 1960 's the effectiveness of soil-slurry came into question because it was often ineffective in maintaining borehole stability at marginal drilling sites and because the economy of using shaft resistance, in addition to end

Jan 1, 1991

By Jacob Chacko

The Izmit Bay bridge, a 3-km-long suspension bridge crossing of Izmit Bay, Turkey is planned to be constructed in one of the most seismically active places in the world. The site, which has the potential to experience significant earthquakes associated with the relative motion accommodated on the North Anatolian Fault, is underlain by deep deposits of soft soils, and areas of unstable and liquefiable soils. Characterizing the seismotectonic setting, foundation soil conditions, potential fault locations, as well as other geohazards was a critical component for the project concessionaire to finance the project and obtain meaningful bids for bridge design and construction. Given the Build Operate Transfer (BOT) funding mechanism, executing this work in the least possible time was critical to the concessionaire?s financing scheme. Fugro was retained to provide geotechnical, geological, and seismological evaluations for the project region, and to generate data for contractors to develop reliable designs and bids. The uncertainties in these data made it difficult for the BOT concessionaire to finance the project and tender Bridge design and construction. The investment in an early and comprehensive site characterization program to evaluate and quantify those uncertainties allowed the concessionaire to save schedule, provide a robust bid basis to bridge contractors, and persuade banks to finance what was perceived to be a relatively high risk project.

Jan 1, 2011

By Gyimah Kasali

Rapid Load Testing was performed as part of an extensive drilled pier testing program for the University of California Berkeley Capital Improvement Program. The purpose of the program was to: (1) Verify the axial compressive design capacity values for the planned 24" piers, and to estimate the capacity of the existing 30" CIDH piers, and (2) To evaluate the seismic performance of the proposed drilled shafts. The Fundex PLT was used since the loading period of the PLT is very similar to the period of a seismic event, making it an ideal tool to model the pier response to seismic events. "Performance-based design" of structures subject to seismic loads has been of particular interest to UC Berkeley Seismic Review Committee and the Pacific Earthquake Engineering Research Center. The comparison of static tests to Rapid Load testing also provided valuable correlations. The program represents one of the most comprehensive drilled pier test programs on the West Coast. The testing program consisted of Rapid Load Testing using the Fundex PLT on 6 drilled piers. Rapid Load Tests were followed by conventional static compression and tension tests on selected piers, followed by another cycle of rapid load tests on the statically tested piers. The piers featured extensive instrumentation to allow detailed interpretation of the test result. Correlations were drawn to compare static load test result to that of the PLT in the particular soil profile, and the PLT also provided the data to analyze the ultimate seismic capacity of the piers. The load test results indicate that the ratio of interpreted failure load from the PLT data to the corresponding load from the static load test data is about 1.2 to 1.3 for the clayey soils underlying the test site. The results also indicate that the PLT offers an economical approach to defining the stiffness of drilled pier foundations subjected to seismic loads for use in performance-based design.

Jan 1, 2002