Search Documents

By Hakan Gürsoy, Kemal Bilir, Bahri Öteyaka, Ali Uçar, Oktay Sahbaz

"Jet diffuser flotation column (JDFC) is a flotation device resembles Jameson flotation cell (JFC) in terms of operational principles, but it has significant difference structural points of view. This difference is an essential change in the downcomer to provide an increase of performance of the cell for the coarse particles. By using the hydrodynamic and fluid mechanics principles (Sahbaz et al., 2013) downcomer was changed as a diffuser, therefore turbulence at the end of the downcomer was reduced to provide better aggregate stability and homogeneous dissipation of the bubbles in the separation tank. According to experimental results carried out in pilot scale JDFC, not only higher flotation performance comparing with Jameson cell was obtained specifically for coarse talc particles in a certain condition, but also quiescent froth layer was acquired. In these tests, vertical pipe of JDFC having inlet diameter of 6 cm and outlet diameter of 11.5 cm was used with separation tank having the diameter of 39 cm. By using the data, pilot scale JDFC having 410 cm vertical pipe integrated with separation tank was produced and flotation tests were carried out by using the naturally hydrophobic mineral (talc). Finally, the talc recovery obtained as 94% by the use of JDFC, while Jameson cell has the recovery of 77% for the particle size of 250 µm."

Jan 1, 2014

By Douglas Fuerstenau

"Comminution not only is the major energy cost in mineral processing but it also can limit the grade of ores that can economically be processed. Rittinger first postulated that the energy for comminution is proportional to the new surface produced. Because most of the strain energy needed to initiate and propagate cracks in particles cannot be recovered, researchers reported woefully low comminution efficiencies. Recognizing this, Schoenert proposed that the baseline for assessing comminution efficiency should be the mechanical energy needed to break single particles. After extensive single-particle studies, Schoenert turned to comminuting beds of particle in piston dies. Finding particle-bed comminution to be energy efficient, he had the brilliant conception of making the process continuous, namely his invention of the choke-fed high-pressure roll mill (HPGR). Practical comminution involves masses of particles, which can lead to energy efficiencies far less than that of single-particle breakage. A three-way classification of grinding modes in terms of the mobility of the particle mass provides the necessary insight into the low efficiency of different comminution machines: namely, single-particle breakage, confined particle-bed grinding (HPGR), and loose-bed grinding (ball mill). Examples are given for determining and comparing comminution efficiencies. The size distribution of comminuted products become self-similar, and a single parameter, the median size, can be used to quantify the extent of comminution. The reduction ratio, expressed in terms of the mean size of the feed and product, varies linearly with expended energy and the slope of such plots is a measure of the grindability of the mineral. This approach clearly gives the order of energy efficiency as single-particle > particle-bed > loose-bed comminution. HPGRs are more efficient at low reduction ratios but lose that advantage at higher reduction ratios. Extensive hybrid grinding experiments carried out with our instrumented ball mill and HPGR showed significant energy savings by first comminuting the material in the HPGR and followed by the ball mill. At Cerro Verde an industrial-scale hybrid HPGR/ball mill system is reported to have a 13 percent energy savings over a SAG mill/ball mill system."

Jan 1, 2014

By Andrzej Luszczkiewicz, Alicja Bakalarz

The application of new collectors is considered to improve the beneficiation of Polish sedimentary complex copper ores from the Legnica-Glogow Copper Basin (SW Poland), the upgradeability of which becomes more difficult because of ores grade declining. One group of potential collectors is represented by nonpolar reagents. According to the available literature data, only selected sulfides float in the presence of the nonpolar liquids. The paper presents laboratory scale flotation results for the main sulfide minerals occurring in the Polish copper ores applying either thiol (potassium ethyl xanthate) or nonpolar (aqueous emulsion of n-dodecane) collectors. The investigated feed contained 1.91 % Cu in the form of sulfide minerals such as bornite, chalcopyrite, chalcocite and covellite. Other sulfide minerals including galena, pyrite and sphalerite were also present in the samples. Several flotation tests with various doses of each collector were conducted. Mineralogical analyses of flotation products were carried out and the results compared. A comparison of the results indicated that all sulfide minerals floated well with high recoveries ranging from 91 % to 99 % in the presence of the thiol collector. The use of the nonpolar collector provided results in flotation of sulfide minerals with different terminal recoveries from 61 % for chalcopyrite to 100 % for sphalerite. The most significant differences in flotation in the presence of both types of collector under various conditions of upgrading were observed for chalcocite, chalcopyrite and covellite. Similar flotation results were observed for sphalerite and galena for both collectors. The studies confirmed selective flotation of sulfides from the copper sulfide ores of the Legnica-Glogow Copper Basin in the presence of nonpolar collectors.

Jan 1, 2014

By A. Güney, G. Önal

"Karagedik Chromite Concentrator of the ETI Holding Co., which is located in Fethiye (south Turkey), has been producing chromite concentrate assaying 47-48 % Cr2O3 from the chromite ores containing 30-35 % Cr2O3 by using gravity separation methods since 1920. The tailings having 13-14 % Cr2O3, which had been removed from this plant, were accumulated at the stockpiles amounting about 1.2 million tons. In order to recover the ultra fine chromite particles from the Karagedik Concentrator tailings, the new process including Wet High Intensity Magnetic Separation and column flotation, was developed and the Karagedik Research Pilot Plant based on this process was commissioned in 2000. At this plant, the final concentrates assaying 46-48% Cr2O3 were produced and overall plant recoveries are about 60-65%.At the chromite concentrators using gravity separation methods, if their material size is about minus 1.0 mm, chromite particles especially pass to fine fractions according to their mineralogical structures and the ore-genesis (Önal and Güney, 1990). Generally, after crushing and grinding, the shaking tables and spirals are used at the chromite concentrators; therefore fine size chromite particles (-0.038 mm) are removed as tailings. Cr2O3 content of the -0.1 mm size fraction with 52.3% of the total amount is 19.58 % with Cr2O3 distribution of 82.6%.In order to upgrade the minus 0.1 mm size fraction of the tailings, assaying about 20% Cr2O3, Karagedik Research Pilot Plant (KRPP), which includes Wet High Intensity Magnetic Separator (WHIMS) and Column Flotation units, was installed by Istanbul Technical University (ITU), Mineral Processing Section in 2000.Feeding material of the KRPP having 5 tons per hour capacity is obtained from stockpiles amounting 1.2 million tons. After attrition scrubbing, the feed is sent to a screen with aperture of 1.0 mm. The screen overflow, assaying 5-6 % Cr2O3 is removed as tailings. Screen underflow is classified to –1.0+0.1 mm and minus 0.1 mm size fractions by using cyclone and sieve bend. –1.0+0.1 mm size fraction assaying 6-7 % Cr2O3, is sent to existing gravity separation plant. Minus 0.1 mm size fraction is firstly fed to WHIMS for pre-concentration and non-magnetic product assaying 10-11 % Cr2O3 consisting of serpentine, talc and olivine minerals are separated as tailings. Also magnetic product (25-30 % Cr2O3) obtained from WHIMS is fed to the two stages conditioners after dewatered to 30 % solid ratio."

Jan 1, 2003

By Lev O. Filippov, Inna V. Filippova

"Flotation of metal-organic precipitate in column is sensible to the hydrodynamic conditions determined by the diameter and dispersion of rising bubbles. Thus, the dissipation energy in the system resulting of ratio between superficial fluid velocities (gas and feed) in the column is main parameter for precipitate flotation in pilot or industrial scales. The knowledge of aggregate structure can lead to better understanding and control of many solid-liquid separation processes (sedimentation, filtration, thickening and flotation). Many authors highlight the importance of structural properties (i.e. floc density) for different industrial applications.This approach was applied to achieve the flotation of molybdenum precipitate obtained with organic collector a- benzoin oxime for molar ratio 1:2. Flotation tests were carried out at lab and pilot scale with rigorous control of the size distribution of bubbles and the values of dissipation energy in the systems.Structural evolution of Mo precipitate and the destruction phenomenon were described by using of the various fractal dimensions, which were deduced from experimental data of laser sizer devices and optic microscopy pictures of precipitate. The boundary fractal dimensions Df of large aggregates allows the detection of a structural scaled organisation of the precipitate flocs (elementary germs-microflocs-flocs). The fractal dimension of the particle mass distribution Dm=1.94+/-0.15 suggests, for the floc structure, a cluster-cluster aggregation process either with structuration or breakage phases.The destruction process characterised by a fractal dimension Dg controls the final size distribution. The floc destruction occurs for the lowest values of the dissipation energy (0.02 – 0.05 W/kg). The relation between Dg and the system dissipation energy Et (for various energy E dissipated in the agitation cell) involves the different breakage mechanisms of aggregates in function of the aggregation bonds (Fig. 1).Besides, the destruction of floc produces very fine particles (elementary germs or/and microfloc according to E), and thus induces the difficulties of bubble-particle attachment during the precipitate flotation in column. Yet, very small bubbles, which increase the collision probability, would make the flotation feed rate decrease. The optima ratio between superficial gas and feed velocities are determined for bubble size and flotation results control at pilot scale. Thus, it is possible to providing the catastrophically changes of precipitate column flotation by using the following established experimental relation: the mean diameter d of the flocs under the action of dissipated energy Et follows a power like law (d~Et -0.5). This allows estimating the size distribution of flocs for the E values which can appear in column."

Jan 1, 2003

By P. Prakash

A dual-drive planetary mill, which has a rotating shaft that sweeps a circle of diameter 750 mm, has been designed. The planetary mill is powered by a 5 hp motor to rotate the main shaft and a 3 hp motor to rotate the jars. The charge dynamics inside the horizontal-axis planetary ball mill was established using three-dimensional DEM simulations. The simulation results provided data to determine the impact energy distribution and the effect of process parameters such as mill speed and filling. It has been observed that the mean impact energy per unit time increases with rotation-to-revolution ratio, whereas the average number of inter-particle impacts per unit time decreases. The mill was also used to synthesize a variety of powders. Here three case studies of reaction milling are briefly presented: (i) cementite and silicon carbide, (ii) oxide dispersed strengthened (ODS) steel, and (iii) magnetite from blue dust. In each case, the powder was produced by mixing and then milling the corresponding pure components. The phase evolution, particle size distribution, and morphology of particles during milling were studied for various samples collected at different milling times using laser size analyzer, SEM, TEM, and Mössbauerspectroscopy. The results established a convenient way to produce powders of high technological and commercial value.

Sep 1, 2012

By R. Bugueño, W. Calderón, G. Montes-Atenas

From the point of view of industrial performance of metal extraction, the efficiency of a column leaching operation depends strongly on the leaching agent and the ore properties such as mineral composition, mineral liberation and particle size distribution. One aspect that has become particularly important is how the leaching solution flows through the porous structure which contains the valuable minerals. It is known that the output flow rate of leaching solution depends mainly on factors of the input flow, environmental condition and porous bed properties. The latter factor is often evaluated and reported under saturated conditions but in practical leaching systems unsaturated conditions are dominant. This investigation has the purpose of determining the residence time of the leaching solution in columns with different diameters under unsaturated conditions by using experimental data and numerical simulations. Laboratory leach test were performed using isothermal jacketed columns with top cap to reduce the evaporation. The simulations were performed using the software SVFlux® which incorporates material properties such as Soil Water Characteristic Curve (SWCC) and Unsaturated Hydraulic Conductivity. Preliminary results indicate a non-linear asymptotic behavior of the saturation rate with respect to the operation time. Results from numerical simulations show the same non-linear behavior and a considerable delay between input and output flows. Further analysis concerning with the effect of transpiration and evaporation mechanisms is discussed.

Jan 1, 2014

By Haghi. Hamed, Javad Vazifeh Mehrabani, Mehdi Sedigh

In this investigation, the possibility of physical separation methods such as attrition scrubbing, hydro-cycloning and also reverse flotation were investigated for silica and calcite removal from relatively low grade kaolin. The head sample was provided by the Iran China Clay Company and the major oxides contained in the head sample were Al2O3, SiO2, CaO and Fe2O3 with grades of 15.07%, 71.05%, 4.35% and 0.52% respectively. The liberation degree of calcite and iron impurities from kaolin particles were over 80% for particles finer than 210µm and 53µm respectively. Attrition scrubbing tests were carried out with scrubber cell of the conventional Denver flotation cell model D-12. Laboratory scale hydro cyclone was applied for the beneficiation of kaolin. Attrition scrubbing tests with control screen of 106µm did not achieve the desirable yield for purification of this kaolin sample, but hydro cyclone experiments resulted in better results. Hydro cyclone with 2.54 cm diameter used and the only variable was the cyclone inlet pressure ranging from 68.65kPa to 98.07kPa. The best inlet pressure was found to be 68.65kPa. Based on the optimized condition, Al2O3 and CaO amount in the hydro-cyclone overflow was 23% and 1.47% respectively. However weight recovery of the overflow in each cyclone experiment was less than 30% and multi stages of hydro-cyclones would have to be applied for higher weight recovery and better yield. All of the flotation tests were carried out in the conventional Denver flotation cell model D-12. Reverse floatation tests for calcite removal were carried out under alkali pH based on full factorial design of variables in 2 levels including one center point. The three parameters tested were collector dosage (gr/ton), pH and depressant dosage (gr/ton). The collected data from flotation tests were analyzed and optimized collector and depressant dosage were 1000 gr/ton and optimized pH was 8.5. Under the above mentioned conditions, calcite removal was about 75% and CaO content in the final product was reduced from 4.35% to 1.33%. However calcite removal will increase to more than 83% if the feed particle size in flotation tests is reduced from 210µm to finer than 53µm. Finally after optimization, the best working condition and possible flow sheet were developed.

Jan 1, 2014

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisinger

"INTRODUCTIONThe objective of this work was to deport silver into a residue suitable for subsequent extraction without compromising the high base metal extraction during the pressure oxidation.RESULTS AND DISCUSSIONThe complex sulphide from the tailing pond of Cannington mine, Australia, was re-grounded and a bulk concentrate was recovered by flotation. The major economic sulphides are galena and sphalerite. The chemical analyses revealed 17.22% Fe; 4.88% Zn; 8.22% Pb; 9.49% S2- and 422 g/t Ag. The baseline cyanidation yielded 36.60% of silver at high cyanide consumption (24.17 kg/t NaCN). Pressure oxidation at 150°C (in the absence of iodide), followed by cyanidation of the residue yielded 8% silver extraction. Pressure oxidation was carried out at 110-150°C in sulphate media with additions of potassium iodide and the resulting residue was subjected to cyanidation. High recovery of silver was achieved because its incorporation into lead-hydronium jarosite during the pressure oxidation was minimised, while its deportment into the cyanide-soluble silver iodide was favoured (Figure 1). Silver recovery decreased slightly at high temperatures (140° and 150°C) because of the enhanced stability and kinetics of leadhydronium jarosite, but this could be overcome by increasing acidity and iodide concentration of the slurry."

Jan 1, 2003

By H. J. Liang

In this study, zeta potential and contact angle measurements of pyrite before and after interacting with Thiobacillus ferrooxidans are carried out to investigate the changes in its surface properties. The results show that, after pyrite interacting with Thiobacillus ferrooxidans and its metabolite, the surface electricity of pyrite changes obviously, resulting in a notable shifting of isoelectric point to lower pH value, but the contact angle varies little. Bacterial protein plays the most important role in the interaction. This work is helpful to disclose the mechanisms of Thiobacillus ferrooxidans de-pressing pyrite flotability.

Jan 1, 2014

By D. Szyszka

During passing gas bubbles through mineral suspensions, some mechanical carryover of fine particles to the froth layer always takes place. The entrainment of mineral particles is influenced by many parameters, mostly by the particle size and the concentration of the frother. The paper deals with influence of selected frothers (methylisobutylcarbinol (MIBC), a-terpineol, and hexadecane tricosaethyleneglycol ether (C16E23)), common laboratory flotation frothers, on the mechanical car-ryover of quartz, a typical gangue mineral component of ores. Entrainment tests were carried out in a laboratory Mechanobr flotation machine with quartz particles suspended in aqueous frother solu-tions. The mechanical recovery of quartz in the presence frother was increasing with time and reached plateau after about 20 minutes of flotation. The plateau level of quartz recovery depended on the frother concentration. Initially an increase of the plateau with frother concentration was observed until the plateau reached the highest level called the maximum recovery emax. The emax can be used as a parameter to characterize the ability of frothers to entrainment. In the studied quartz-frother flotation system the maximum entrainment was 32%, 50% and 80% for methylisobu-tylcarbinol (MIBC), a-terpineol, and monohexadecane tricosaethylene glycol ether (C16E23), re-spectively. A comparison of the maximum entrainment factor emax with other, known from literature, indices such as bubble critical coalescence concentration (CCC), dynamic foamability index (DFI), Jw, e =25%revealed, except DFI, their similarity.

Jan 1, 2014

By Vishal Shukla, Ashok Kumar, Manas Ranjan, D. Chakraborty, Narayan Sharma

Jigging has a very important role in mineral processing Industry. Upgrading of Iron Ore by jigging has been an emerging trend. A detailed investigation is carried out to understand the influence of Jig feed granulometry and bed height during jigging operation. Noamundi jig plant data shows that variation in jig feed granulometry, feed quality and bed height are major contributors to fluctuation in jigging performance. At Noamundi the feed size (-10.0+0.5mm) fraction is used for fines jigging operation. To understand the effect of granulometrey on jig plant performance such as yield, separation efficiency and Fe recovery. In this context The performance of jigging was evaluated by daily average data from jig operation was used to study the influence of feed distribution on jigging performance .Coarser fraction (+6mm) has a positive influence , whereas fines fraction (-0.5mm) tends to lower performance . During Jigging rearrangements of Particles takes place due to an alternate expansion and compaction of Jig Bed .These particles are arranged by increasing density from top to bottom. During the particle stratification, Jig bed physically cut at desired horizontal particle density plant to separate the desired product. Investigation shows that optimum bed height is required at different Jig feed quality to achieve desired product quality, maximum separation efficiency and Fe recovery. This Paper will illustrate role of granulometry and Bed height control on Jigging plant performance.

Jan 1, 2014

By M. Amani, A. Akbarinasab, M. Bazmandeh

The fourth iron ore production plant at Golgohar mining and industrial company consists a ball mill and wet medium intensity magnetic separators (3500 Guss). The ball mill product applies directly into MIMS and the MIMS concentrate directly transfers to the low intensity magnet separators (LIMS). The thickener is used for dewatering of MIMS and LIMS tailings. By sampling from streams of ball mill and separators, it was defined that the grade and iron recovery were 60% and 80% respectively while they would be 66% and 90% respectively based on the designing documentation. The average of P80 in the ball mill was 342 micron in a month that is coarser than optimized value. This problem was related to unsuitable operation of grinding. For optimization of grinding efficiency, the amount of charge volume was investigated as a variable. The measurements illustrated 32% charge volume. For increasing grinding efficiency, the charge volume was increased 1% and 1.6% in two stages. The results showed ball mill power draw average reached from 3650 kw to 4120 kw and the average P80 reached to 329 micron. All of parameters calculated about 35 day before and after change. Average of Ball mill feed iron ore grade before and after change was 49.24% and 50.32% respectively. This change caused an increase in efficiency of MIMS, where the enrichment ratio and concentrate grade increased 2% and 1.9% respectively. For increasing the iron grade of the MIMS concentrate; the orifice of the tail flow exit pipe changed from 4 inch to 6 inch and the concentrate grade increased 2%.

Jan 1, 2014

By Yong Liu, Peng Qian, Shu-Feng Ye, Shao-Jun Chu, Pei-Wei Han

"Chromite with a low mass ratio of Cr to Fe (Cr/Fe ratio) was treated by the carbochlorination method using solid chlorinating agent (MgCl2 and CaCl2) and carbon in the present paper. The results showed that iron could be selective removed mainly in the form of FeCl2. The removal of iron was indirectly, which consisted of the decomposition of solid chlorinating agent to release Cl2/HCl and the carbochlorination of FeO•Cr2O3 by Cl2/HCl and C. The Cr/Fe ratio increased as increasing temperature from 700 ? to 900 ? in air atmosphere, while the tendency was opposite in N2 atmosphere. The removal efficiency of iron by CaCl2 was better than that by MgCl2. At last, a new pelletizing process was proposed to treat fine chromite with a low Cr/Fe ratio based on carbochlorination method, which could produce the high quality roasted chromite pellets with higher Cr/Fe ratio and compressive strength. INTRODUCTION Chromite is mainly used for the production of ferrochromium. A high Cr/Fe ratio (>2) of chromite is usually required to meet the technical specification of ferrochromium.(Gasik, 2013) Attentions have been attracted to the economic and efficient methods for the recovery of chromium from lower-grade ores as the higher-grade ores become depleted. However, the Cr/Fe ratio is difficult to improve through the conventional beneficiation methods (such as gravity concentration, flotation) due to the spinel composition, although beneficiation methods could increase the metal content of chromite ores by removing gangues.(Nafziger, 1982) The main industrial mineral of chromite is (Fe,Mg)O•(Cr,Al,Fe)2O3, which belongs to spinel magnetite.(Liu, 2013) Iron should be selectively removed through the structural dissociation of spinel to increase Cr/Fe ratio.(Nafziger, 1982)"

Jan 1, 2018

By V. Panayotov

Flotation practice usually uses the Sheridan-Grizvold selection method, where zinc minerals are activated by addition of copper sulphate and depressed by addition of sodium cyanide, ferrous sulphate, zinc sulphate or various mixtures of these reagents. The method is suitable for the flotation of sulphide ores, which, do not bear precious metals, such as silver and gold. When classical technology with cyanide is applied to depress zinc minerals, the precious metals, which are contained mainly into lead minerals, are dissolved into the solution, which represents a technological loss. In order to avoid this process, we have made use from the knowledge on the semiconducting properties of lead and zinc sulphide minerals. We have changed the surface charge of minerals by means of an electrochemical impact realized by direct current application and specially designed set of insoluble or semi-soluble electrodes. Thus, flotation separation of lead and zinc sulphide minerals was achieved, at increased recovery of lead, zinc and silver. The technology proposed was implemented in a Bulgarian flotation factory; it worked over 5 years providing significant, positive economic, technological and environmental impact. Silver recovery was increased by 0.8-1.0 %, and lead and zinc recovery was increased by 0.8-1.0 %. The technology is easily controllable and adaptable to raw materials and parameters of the technological process. It can be paid back for 6-8 months after the implementation. Keywords: lead-zinc flotation separation, electrochemical impact

Sep 1, 2012

By W. P. Roux

With depletion of higher grade iron ore reserves, and the need to process finer, lower grade material; there is a need to better understand the recovery efficiency of jigging process. The use of Positron Emission Particle Tracking (PEPT) was examined as a technique, to study the motion of particles inside a laboratory batch jig. PEPT is a noninvasive method that can provide three dimensional kinetic data of a particle during jigging. Particles with different densities and sizes were traced under the same jigging parameters, to obtain a data set that can be used for the development and verification of jigging models. From the results, detailed information on the stratification rate of a particle was obtained, with adequate resolution to see particle movement through an individual pulse. Detailed data of this nature is critical for the validation of CFD and DEM models. Keywords: positron emission particle tracking, jigging, jig models

Sep 1, 2012

By In-Kuk Bae, Kwang-suk You, Joobeom Seo, Kwanghyun Bea, Hyung-Seok Kim

Arsenic in base metal sulfide ores is highly penalized owing to high costs for its control in metallurgical processing. The arsenic element in the lead-zinc ore, which is target ore in this study, has been shown to be in the form of arsenopyrite. Experimental work in this study is about arsenic rejection flotation, using depressant suitable for the removal of arsenopyrite from the Pb concentrate. The arsenic rejection flotation also included the oxidation treatment of Pb concentrate with H2O2. In this study, the Pb concentrates containing 80.7% Pb and 0.25% as was obtained with the additions of aluminosulfate as arsenic depressant. And through IR measurement, it was also known that the addition of aluminosulfate during arsenic rejection flotation formed calcium aluminosulfate hydrates on the surface of arsenopyrite particle, resulting in rendering arsenopyrite hydrophilic.

Jan 1, 2014

By A. Gueciouer, A. Akkouche, K. Chalah, A. Benmounah

"Drilling solid waste is a typical industrial solid waste, and it is a major pollutant source to ecological environment. Generally, waste management dewatering systems separate solids and fine particles from the liquid phase of drilling fluid, thereby leaving a clarified aqueous solution and allow the cleaning of waste fluids. Typically, dewatering waste management systems clean drilling fluid through coagulation, flocculation and/or mechanical separation. Chemicals used in dewatering are based on the coagulation-flocculation process, which it facilitate the removal of suspended solids and colloidal particles. The factors which can promote the coagulation-flocculation are velocity gradient, contact time, and PH. The objective of this work is to optimize a formulation adequate for dewatering based on the coagulation-flocculation process used coagulant (Aluminum sulphate), anionic flocculants (Partially Hydrolyzed Polyacrylamide) and anionic polyelectrolytes (in solid form with linear chain with very high molecular weight). The results obtained show the good efficiency of the coagulant and flocculants. INTRODUCTION Rig site dewatering of drilling fluids with recycling of processed water can help an operator to comply with environmental rules by reducing volumes of waste and reducing long term liabilities. It can also reduce disposal costs and provide a cleaner drill site overall. Most of the environmental concerns during the 1980s involved hazardous materials and toxic wastes. Drilling fluids, many of which are chemically benign, have escaped many of the difficult-to-comply-with rules and regulations. During the 1990s, however, operators may be required to submit a written plan for liquid waste reduction for even nonhazardous materials. Many states and local agencies may institute total bans on oil field wastes. Drilling rigs typically produce about 1 bbl of liquid waste for every 1 ft of hole drilled. Thus, a typical drilling operation can produce a large quantity of waste [1]. To improve the dewaterability of sludge, different pretreatment processes have been widely studied and developed including thermal, chemical, magnetic, mechanical, acoustic, electric, electro-acoustic and their hybrid treatment processes [2]. Rig site dewatering (figure 1) is the process of injecting coagulants or flocculating chemicals into the mud entering a large clarifying centrifuge. Coagulation occurs when the solid and allowing it to be attracted to other solids by van der waals forces. Flocculation is the binding of individual solid particles into aggregates of multiple particles. It is physical, rather than electrical, and occurs when one segment of a flocculating polymer chain absorbs simultaneously onto more than one particle [3]."

Jan 1, 2018

By K. V. Fedotov, E. V. Zelinskaya, O. V. Ulanova

"Mining enterprises, in particular, those on the territory of the Siberian platform, produce large amounts of pumped water, which cannot be recycled because of its high mineralization and, thus, is discharged as liquid waste either back into the ground or onto the surface. However, groundwater is often a valuable raw material and a source of useful chemical substances. Brines are unique groundwaters. In the current environmental and economic situation, the huge loss of natural raw materials and their deliberate conversion into wastes is unaffordable. The exploration of non-traditional sources of minerals such as the hydromineral resources (including pit water) is a matter of rational nature management. The industrial value of brines of the Siberian platform is due to the high contents of rare alkali and earth alkaline elements (lithium, rubidium, cesium, strontium, bromine, etc.). The absolute concentrations of these elements in brines are tens of times higher than the lower limits of the mining cut-off. The long-term data analysis was performed to estimate the environmental impact of liquid waste from two mining enterprises, namely, Korshunovskii (Irkutsk region) and Udachnaya (Southern Yakutia). The study was focused on the prospects of hydromineral resources as non-traditional sources of valuable elements and the exploration of technological processes for the selective extraction of rare alkali and earth alkaline metals from natural multi-component brines aimed at decreasing their negative environmental impact. The environmental and economic efficiency was proved for the processing of complex brines and the integrated selective extraction of rare earth metals from sodium chloride brines of the Korshunovskii plant and calcium chloride brines of the Udachnaya plant based on the ion exchange sorption, eluent chromatography, flotation, crystallization, and freezing techniques. The basic technological schemes were developed for the metal extraction from pit water and brines.INTRODUCTION In the Irkutsk region (the Angara–Lena artesian basin) and in Yakutia (the Olenek and Tunguska artesian basins), several mineral deposits are developed and, incidentally, aquifers bearing brines of different types are opened, which are eventually converted into liquid production waste (Rusetskaya et al., 1994) This raises the issue of the burial or utilization of brines since their use within the water circulation is impracticable under the existing technological conditions while their discharge into the surface watercourse is unacceptable because of the harmful environmental impact."

Jan 1, 2018

By Cristiane Ericksson, Ananda Scomazzon, Irineu Schadach, Juliano Tonezer

The state of Rio Grande do Sul, southern Brazil, appears on the national and international scene as an important producer of precious stones and the main gems are amethyst, citrine and agate. However, despite the immense potential of this mining activity, the extraction and processing of gemstones in Brazil present critical issues of infrastructure, which prevents a better development of these activities. In general, local production is still concentrated in small rudimentary mining. Recently some of these mines have begun to regularize their activities, in conjunction with the National Department of Mining Control. Besides these problems best practices for extraction activities and environmental control are not usually observed. Another problem which is placed in a critical way is the absence of aggregate value for the products of small mines. In this situation, the miners have great problems to obtain access to technology and adequate infrastructure. In most cases miners need negotiate their gems without processing, transferring most of the profit to intermediate traders. These results in heavy losses for the producer and for the communities involved. Given this scenario, the present study aimed at defining systems technically and operationally viable to be implemented in these communities in order to add value to gemstones. In this study best practices to thermochemical coloring systems, analysis of effect of raw materials and operating parameters on the final color of the gem were analyzed with attention.

Jan 1, 2014