Search Documents

By John Ralston, Stephen Grano, Yongjun Peng, Daniel Fornasiero

"A specially designed mill which allowed the control of pH throughout grinding was used to study the effect of grinding conditions on galena flotation and galena separation from pyrite. The changes occurring on the mineral surface during grinding were investigated by EDTA extraction and ToF-SIMS measurements.Galena flotation and galena separation from pyrite were strongly dependent on the type and amount of oxidation species produced on galena and pyrite surfaces under different grinding conditions. Iron oxidation species depressed both galena and pyrite flotation, whilst lead oxidation species activated pyrite flotation but had little effect on galena flotation. Optimum galena flotation and galena selectivity against pyrite were achieved by selecting grinding conditions that enabled lead and iron oxidation production to be controlled.Grinding conditions had a large effect on the flotation of the galena particles of different sizes. Flotation of fine galena particles (-10 µm) was depressed by iron oxidation species derived from the grinding media. Chromium grinding medium decreased the production of iron oxidation species and therefore increased the flotation of fine galena particles."

Jan 1, 2003

By E. V. Manlapig

"Some researchers postulate that the floatability of a particle in the streams of an industrial flotation circuit is a function of only its size and liberation properties. They do not discount the importance of reagent or surface contamination on particle floatability but assume that the reagent coverage or surface contamination of the particle surfaces is essentially uniform for particles of similar size and mineralogical properties when subjected to a particular chemical regime.In this paper, samples collected from batch tests performed on different streams of the Red Dog lead cleaning circuit have been characterised with respect to their size, mineral association and mineral surface exposure. An analysis of this data set indicates that particle recovery rate is significantly affected by mineralogical properties - in particular the degree of valuable mineral surface exposure.However, through the use of a nodal analysis technique developed by the authors, it can be concluded that particles with the same size and mineral composition do not all float with the same rate, but with a distribution of rates. The characteristics of this floatability distribution do not change during the flotation process. It is suspected that the particles within a size mineralogical class in this study have varying degrees of surface oxidation and that this results in varying particle flotation rates. Thus basing particle floatability on size and mineralogical effects, alone, in a flotation model is not always valid."

Jan 1, 2003

By Güven Önal, Zeki Dogan, Neset Acarkan

In this study, it was aimed to produce glass sand with less than 0.15% Fe2O3 for window glass manufacture and glass ware grade with less than 0.05% Fe2O3 from Yalõköy sand dunes having 0.48% Fe2O3. In order to reduce the iron content of the Yalõköy sand dune, magnetic separation, flotation, scrubbing, H2SO4 leaching and drying were used. The optimum iron removal was achieved by H2SO4 baking at 150oC and 8 kg/t acid consumption. In this way, sand concentrate was obtained with 0.04% Fe2O3 and sand recovery 95%.

Jan 1, 2003

The concept of the Unified Comminution Model (UCM) was presented at the 23rdIMPC. The model utilises computational techniques to calculate the mechanical environment in any comminution device, and then incorporates the outcomes from rock breakage tests to predict the product from a device. The model is fully mechanistic, and incorporates the capability to simulate novel equipment. This paper presents the progress on the first application of this concept to applied comminution equipment. This novel comminution model aims to integrate all comminution models within a single struc-ture. This will provide a step change in the predictive power of comminution models, and include a wide range of particle properties that will enable it to be linked to the upstream and downstream process of mining and recovery. Major advances over current models will be the capability to predict liberation, preferential grinding, performance of new and novel devices, and to have power as an integral driver of the comminution simulation process. The methodology and model structure have been developed. An equation within a population balance framework has been derived as the basis for the UCM. A set of SAG mill pilot has been used as the first test case. The breakage characteristics of the ore have been extensively tested utilising a new range of breakage tests required by the rigorous UCM structure. The mill was simulated with the EDEM - DEM software. A partial test simulation of the pilot SAG mill has been conducted. This serves to demonstrate the feasibility of this modelling technique, but still lacks important ore characterisation components that are under development. The study has raised a number of significant challenges to the accepted understanding of the comminution process. Through addressing these challenges considerable insight has been gained into the energy environment in mills and the requirements of breakage testing. The ore characterisation methods and energy transmission derived from DEM simulations remain as major research items.

Jan 1, 2014

By O. A. Bascur

It is difficult to analyse the economics without an integrated view of mine transactions, stockpile inventories, process flows and assays. The lack of integration of mining and metallurgical information with sufficient detail to analyse and act is a problem. However, to take action requires real time information from manufacturing assets, corrected for gross errors from trucks, shovels, conveyors, faulty sensors, bad instrument calibration. Validation methods use process models to identify inconsistent information in the case of corrupt actionable information. This paper presents new strategies that transform the data into business information for continuous improvement and optimization. This technical presentation will review recent implementations enabling large metallurgical complexes to improve their data quality for overall production and energy management. A competence center emerges as an enabler for implementing operational intelligence. The evolution of Web services to troubleshoot plant information and to collaborate at the enterprise level is presented.

Jan 1, 2014

By Santiago Garcia, Dariusz Lelinski, Devan Govender, Tyson Baker, Mads Jespersen

"In recent years, the scale-up of mechanical flotation machines has been attempted with greater frequency. In contrast, the development of rotor-stator designs has been subject to greater inertia. The rotor-stator components are integral to the operation of mechanical flotation machines, responsible for the key physical processes of solids suspension, gas dispersion and energy dissipation. Design modifications are predicated upon the dual purpose of meeting customer needs while achieving metallurgical performance objectives. Accomplishing the latter is a rigorous undertaking, typically involving the sequential application of fluid dynamics principles, prototyping, smaller-scale research screening studies and larger-scale development projects. This industrial evaluation details the final stages of the forced-air rotor-stator development process using a double-refractory Carlin-type gold ore. A bypass stream of the primary rougher feed was further classified into cyclone underflow and overflow products. Four rotor-stator treatments were evaluated using parallel flotation rows coupled with a randomized statistical design. Only two treatments are compared in this initial assessment. Metallurgical responses were measured as a function of the random variation of key machine factors. Machine characterization measurements complemented the analysis of flotation performance indicators."

Jan 1, 2014

By David G. Hulbert, Daniël J. Oosthuizen, Bernard Muller, Daniël de V. van der Spuy

"OVERVIEWExpert Online is a software system that aims to mimic an informed expert on a minerals processing plant. The primary objective of Expert Online is to provide operators with effective training and on-the-job assistance. Training will mostly be done off-line (e.g. using simulators of the plant), while on-the-job assistance will help the operator during normal operation to run the plant in an effective manner. Although Expert Online focuses on the operator, it is expected to also be of value to other plant personnel, including supervisors and plant managers.Expert Online will make use of novel artificial intelligence technology (developed by MINTEK) known as the Interpreting Expert System (IES). Previously the IES was only able to explain the actions taken by the controller. Expert Online will extend this functionality to also take the process dynamics into account.Expert Online is being developed by a South African consortium comprising MINTEK (focusing on the research and development of the system as a whole), Lonmin (globally one of the biggest platinum producers, with plants suitable to test Expert Online on) and the University of Natal (academic partner, providing consultation and focusing on complex process modelling). The initial application of Expert Online will be on milling- and flotation plants.This paper discusses the structural design of Expert Online for implementation on the latest version of MINTEK’s open control platform, PlantStar, as well as several advances and additions since the previous implementations of the Interpreting Expert System."

Jan 1, 2003

By Xiaodong Jia, Richard A. Williams

"The packing of particles is a fundamental property of a material or system made up of particulates because it underlies many other physical properties of that material or system. Despite being ubiquitous, particle packing has not been an easy subject to study either experimentally or theoretically, except for a few regular shapes.This paper describes the recent developments, arising from research at Leeds, in the computer modelling of packing of complex shaped particles and prediction of physical properties of the structures represented by the packing. The computer model DigiPac, is capable of packing particles of any shapes and sizes in a container of arbitrary geometry. Figure 1 shows a few examples that are relevant to the mining and mineral industry.The ability to predict packing structure of real particle shapes and to compute directly some structuredependent physical properties (such as liquid permeability, mechanical strength/stability, compaction and sintering, dissolution and leaching, etc.) is obviously highly desirable and has significant potential in industrial applications. Examples are presented relating to the packing of granular materials.The mining and mineral engineering industries are well placed to exploit this advance in digital packing and simulation since they deal primarily with asymmetric and complex particulate mixtures. In the future we expect to see a number of developments in this area including:Algorithms that can optimise packing to achieve user-defined propertiesA more rational approach to determining flowability of complex powdersUse of these more realistic packing algorithms linked to blast and crusher design"

Jan 1, 2003

By Choi Sang-Ken, Chung Hun-Saeng, Kim Byoung-Gon, Park Chong-Lyuck

Fine grinding of crystalline graphite was conducted using a dry attrition mill with a vacuum system to investigate the characteristics of size reduction. Low pressure and high temperature conditions in the grinding mill were found to greatly improve the efficiency of the size reduction of graphite. Natural flaky graphite of .100 mesh was ground into sub-micron sizes, then over 90% of the product were able to be reduced below 1?without disrupting their crystallinity in a short period of time. Reducing the atmospheric pressure in the grinding environment promotes the removal of chemical species such as oxygen and water molecules adsorbed on the graphite particle, resulting in effective size reduction while maintaining the crystallinity of graphite.

Jan 1, 2003

By A. F. Usov

A potential of electric pulse disintegration in benification used for primary deposits ores containing precious metals is shown. Of special significance is that PGM and gold grains, being highly plastic, are easily liberated and are not smeared on the disintegrated rock fragments surface. It al-lows gravity separation, which is less expensive and more efficient, to be used instead of chemical processing, which is expensive and environmentally faulty.

Jan 1, 2014

By Sarthak Kaushik

Zeta potential measurements show that the isoelectric point of crandallite, in aqueous solution of 10-2 N sodium chloride is at about pH 5.5. Measurements of turbidity confirm the point of zero charge or crandallite. Calcium ions specifically adsorbed on the surface and thus changed the zeta potential and turbidity. From the measured data, it is confirmed that starch acts as a flocculent for crandallite. Oleic acid, which is a collector used in phosphate ore processing is weakly adsorbed on the surface of crandallite. This results in hydrophobic coagulation of particles resulting in a lower turbidity.

Sep 1, 2012

By Graeme J. Jameson

"When mineral particles are floated in a mechanical flotation cell, it is found that the rate constant, after reaching a maximum value, starts to decline as particle size increases. It had been thought that the reduction in rate constant had been due to the increased prevalence of composite particles in natural ores, for larger particles. However, Jameson (2012) showed that the rate constant for composites is certainly a function of the surface liberation, but the reduction in flotation rate is independent of particle size. Thus all particles are equally affected by reduced surface liberation, independently of their size. He further argued that the classical peak observed in the rate constant with increasing particle size, is a function of machine hydrodynamics. Thus in mechanical cells, the peak may be due to the high energy dissipation rate and its effects on the detachment of particles from bubbles (Goel and Jameson, 2012). Consequently, in a different flotation environment, it may be possible to float large composite particles that cannot be floated in mechanical cells. This paper describes the flotation of large composite particles in a fluidized bed flotation cell. The particles to be floated are fed to a column in which there is a continuous upflow of liquid. A conventional froth layer of controlled depth is formed at the top of the vessel. A fluidized bed of particles is established which provides a gentle environment for the contacting of large particles with bubbles. An example is given where a porphyry copper ore was prepared at a top size of 710 µm, and floated with conventional collector (PAX) and frother (MIBC). The concentrate was separated into size fractions and examined by photography. Composites were observed at all size fractions, but above 400 µm, all particles were composites. The implications for future flotation circuits will be described."

Jan 1, 2014

By Lev O. Filippov, Inna V. Filippova

"Flotation of metal-organic precipitate in column is sensible to the hydrodynamic conditions determined by the diameter and the dispersion of rising bubbles. Thus, the dissipation energy in the system resulting of ratio between superficial fluid velocities (gas and feed) in the column is the main parameter for precipitate flotation in pilot or industrial scales. The suggested limiting factor is the aggregate stability under the turbulence created by the rising bubbles. The stability of precipitate is related to the structural organisation of aggregates, which determines the size distribution of particles during precipitation and flotation stages.Structural evolution of Mo precipitate and the destruction phenomenon were described by using of the various fractal dimensions. The fractal studies allow the detection of a structural scaled organisation of the precipitate flocs. The fractal dimension of the particle mass distribution Dm=1.94+/-0.15 suggests, for the floc structure, a cluster-cluster aggregation process either with restructuring or breakage phases.The destruction process, which occurs for the lowest values of the dissipation energy E (0.02 . 0.05 W/kg) was characterised by a fractal dimension Dg of size distribution. Besides, the destruction of floc produces very fine particles, and thus induces the difficulties of bubble-particle collision during the precipitate flotation in column."

Jan 1, 2003

By D. G. Hulbert

"Mineral processes are complex operations that have been modelled, controlled and simulated by diverse technologies. A review is given of some models of mineral processes in the literature. A new variation of a dynamic process model of flotation is presented. Process models, describing real and relevant physical variables, give a good understanding and good qualitative simulations, but can sometimes require prohibitively difficult and extensive parameter estimations. Process control is usually best done on operational plants by the fitting of system models, which can home in on the plant?s observability, controllability and optimisation. System models can be of a form amenable for use in appropriate techniques for controller design and implementation. The control of milling circuits is discussed in some detail. While simulators use models to predict dynamic or steady-state information, part of their strength lies in their ease of use and their ability to test different types of specifications. Some results are given for a flotation circuit simulator that can be made to solve virtually any permutation of specifications.INTRODUCTIONThe development and application of appropriate technology can lead to better operation of mineral processing plants in industry, so that substantial benefits can be obtained from improved throughputs, efficiencies and product qualities. This paper addresses some of the principles and methods used in the quest for the development and exploitation of such technology. Although the design of processes is often the motivation for modelling and simulation, this paper also targets the use of modelling and simulation for the control and optimum operation of mineral processes. The two processes given the most attention here are flotation and milling.Technologies used in mineral processing range from simple to very complex. Simple technical principles, such as mass and component balances, can yield some simple and effective strategies for modelling and control. However, minerals in particulate form have such complex physical and chemical properties that there appears no end to the complexity that emerges, as more and more factors are taken into consideration in the pursuit of better results and understanding. The situation is aggravated by the complexity of mineral processing plants, which have spatially variable conditions within process units, and complicated interactions between these units."

Jan 1, 2003

By S. P. Das

Tumbling mill is an important unit operation in a mineral processing industry whose operation needs to be understood to make it an energy efficient unit. One of the important mill parameters is the impact spectra generated by collision of the moving charge mass on the mill shell. This process also generates mechanical vibration on the mill shell and propagates to the plumber block of the mill. In this work, we tried to understand the impact spectra by using different minerals such as Banded Hematite Quartzite (BHQ), Hematite and Quartz as mill feed of a semi-autogenous (SAG) mill. The said mill is of 1000 mm diameter and fitted with a force sensor on the mill shell and a vibration sensor on the plumber block. The analysis of the impact spectra was done by taking into consideration the peak impact force above a certain threshold value. It clearly shows that the impact force decreases as the particle size become finer irrespective of the mill feed material. This can be used as an effective tool by the mill operators to have an understanding of the mill product size reduction. The mechanical vibration tapped by a tri-axial accelerometer was analyzed by power spectral density analysis. The vibration signal analysis shows the variation in the power spectrum magnitude both at lower and higher frequency. It also shows inconsistency in case of BHQ where it shows a significant decrease in vibration at lower frequency and increase in vibration at higher frequency. Therefore, the impact spectra analysis is a better method compared to vibration analysis in understanding the mill product size reduction.

Sep 1, 2012

By Shuji Owada, Yang Geng, Natsuko Kuroki

Micro-bubble flotation is considered to be an ideal method for the separation of fine or ultra-fine particles, which are difficult to be separated with conventional flotation and other solid separation technologies. Micro-bubble flotation can increase the probability of bubble-particle collision more than conventional milli-bubble flotation. However, there are also some problems. For example, it is known that the rising velocity of micro-bubble is quite low; therefore, the flotation rate reduces. And also, the bubble-particle adhesion probability becomes lower than that of milli-bubble flotation, which is proved in our prior research. In this paper, we applied ultrasonic irradiation to the micro-bubble flotation system in order to solve the above problems and focused on the bubble-bubble and bubble-particle interactions. For clarifying the behavior of bubble-bubble interaction, bubbles behavior was recorded by high-speed camera under irradiation of various ultrasonic frequencies. As a result, in the case of bubble-bubble interaction, it is proved that bubbles are highly coalesced by ultrasonic irradiation especially in the lower frequency and it can enhance more precise separation. In the case of bubble-particle behavior, it is found that the floatability become higher with the ultrasonic irradiation of higher frequency, and it is indicated that ultrasonic irradiation might improve the bubble-particle adhesion probability. Additionally, it is also found that the apparent CMC of the micro-bubble flotation under the ultrasonic field become much lower with higher frequency than with lower frequency, and it is suggested that the dramatic improvement of hydrophobization is achieved.

Jan 1, 2014

By S. K. Pan

The process flow-sheet adopted in treating hematite iron ore in India through wet circuit generates not only 15-25% slime of Run-of-Mine (ROM), but also results in loss of very high quality fine iron ore particles along with it. As the reserves of hematite iron ore is depleting, it is necessary to explore the possibility of upgrading other types of low grade iron ore and slime for recovery of iron minerals; extensive research in this field is being carried out. While beneficiation of low grade ore is yet to be established, slime beneficiation has been quite successful and many installations of slime treatment plant are underway. In SAIL mines, the slime is mainly the discarded particles from Classifiers, which are less than 0.2 mm sizes. R& D initiative has been focussed on the beneficiation of the slimes (49-60% Fe, 3-10% Al2O3 & 4-10% SiO2) of Dalli mines to generate concentrates assaying 62-64% Fe, 2-3% Al2O3, 3-4% SiO2 and a few innovative facilities for the same has been introduced at this mines of Bhilai Steel Plant (BSP). At Dalli mines, the slime is of very poor quality. A typical slime analysis assays 48.54% Fe, 15.1% SiO2, 8.5% Al2O3 and consists nearly 60% (by wt.) particles less than 38 micron. Slime analysis revealed substantial quantity of very high density mineral particles, those causes jamming of Thickener due to faster settling. A novel technique has been implemented to classify the concentrate ore particles from the gangue mineral particles by processing through Fluidized Bed Classifier (FBC) system, which is a gravity concentrator, to treat 50% of the slime generated and the rest is treated through de-sliming hydro-cyclone followed by Medium Intensity Magnetic Separator (MIMS). A special self-vibrating launder has been designed and introduced into the system to recover tiny iron ore particles, which could not get captured by the permanent Neodymium rare earth magnet in MIMS. The classified iron mineral particles from FBC are further treated in a battery of hydro-cyclones followed by modified Slow Speed Spiral Classifier (SSSC) unit. Multiple feed entry system to the SSSC unit is unique and use of particular feed entry point depends on the desired quality of the product and thus converted to a beneficiation equipment rather than mere de-watering unit. By processing slime in FBC system, the valuable iron ore particles with 62.5% Fe, 5.2% SiO2, 2.23% Al2O3 has been recovered from the slime at a material yield of 30%. And very high valued concentrate particles with more than 65% Fe has been sorted out through the magnetic separation route. The overall extra production of beneficiated slime concentrate is 40-45 tph with 63-64% Fe from a slime feed of 120-130 tph solid. This paper outlines few new approaches in iron ore slime beneficiation at Dalli mines for maximum recovery of valuable minerals. Keywords: fluidized bed classifier (fbc), iron ore slime of dalli mines, medium intensity magnetic separator, slow speed spiral classifier (sssc)

Sep 1, 2012

By V Radmehr

Ammonia and Amonium salts have been recognized as effective leaching agents in hydrometallurgical processes due to low toxicity and cost, easy recovery and high selective recovery of metals. New research findings of considerable advantages of leaching by these agents and elimination of problems associated with acid leaching has resulted in a new approach in the world to this method. The investigations in this field indicate more frequent use of this method for extracting copper from ore and concentrate relative to other basic metals. In this paper, we have attempted to describe the basis and different ammonia leaching methods and present the major research activities in this field for copper. We have also presented the latest findings and related novel processes. Comparative assessment of advantages and disadvantages of this method relative to acid leaching method, kinetic study of copper ammonia leaching and evaluation of Eh-pH diagrams in a system containing water and ammonia are other parts of our study. Finally, by describing the studies on copper extraction from the resulting pregnant solutions, the applicable extraction agents have been reviewed.

Sep 1, 2012

By B. Das

Waste water produced from coal preparation plants posses several problems during dewatering and solid/liquid separation. The natural sedimentation rate of the particles present in colloidal and finely divided suspended form is very slow. Flocculation technology is being applied in most of the coal washeries to recover water which is being accomplished through the use of inorganic salts, polymeric flocculants or both depending on the chemical and physical characteristics of the pollutants present in the waste water. The waste tailing water from Piperware coal preparation plant, Central Coalfield Limited (CCL), India, is highly turbid containing ~ 16000 NTU with negative surface charge in the pH range of 2 to 10. Polymeric flocculants in conjunction with fine magnetite is investigated to achieve faster settling rate with lowest level of water turbidity. The conditions affecting the interaction between the reagents and the turbid particles present in the tailings water are investigated. It is possible to bring down the turbidity of the water to < 90 NTU from very high turbid tailing water by using 2 mg/L of the polymeric flocculent in combination with 0.1 g/L of magnetite at natural pH of the tailing slurry. It has been found that finely divided positively charged magnetite particles in combination with the flocculent selectively coat the negatively charged impurities present in water and thereby increase the settling rate under the influence of a magnetic field.

Jan 1, 2014

By F. S. Hoseinian, K. Filho, D. Deglon, T. Souza, M. Safari

"This paper investigates the reverse flotation of hematite in three laboratory flotation cells with very different contacting environments. The main objectives are to investigate the recovery of coarse quartz by flotation and fine hematite by entrainment. The laboratory flotation cells used were the mechanical, oscillating grid and pneumatic cells. The effect of froth height and solid concentration were investigated in the mechanical and pneumatic cells. The effect of impeller speed and energy input were investigated in the mechanical and oscillating grid cells. Froth height results show that coarse quartz particle recovery decreases almost linearly with increasing froth height due to increased detachment of coarse quartz particles in the froth. Fine hematite particle recovery also decreases almost linearly with increasing froth height due to decreased water recovery and associated entrainment. Agitation/energy input results show that coarse quartz particle recovery increases with increasing impeller speed to an optimum, after which this decreases dramatically. The increase is due to improved gas dispersion, generation of smaller bubbles and increased bubble-particle collision and attachment. The decrease is due to significantly increased bubble-particle detachment at higher impeller speeds. The recovery of coarse quartz particles in the OGC is higher than that in the mechanical cell with an optimum at a much lower energy input. Solids concentration results show that both mass recovery and water recovery increase with increasing solid concentrations. The pneumatic cell achieves higher mass recoveries and lower water recoveries than those in the mechanical cell at equivalent solids concentrations and operating conditions. INTRODUCTIONFlotation is a selective process for separating different minerals from each other. The flotation separation efficiency depends on the recoveries of the mineral species by both true flotation and entrainment (Neethling and Cilliers 2009; Wang et al. 2015). Both chemical variables and hydrodynamic conditions within the flotation cell affect the recovery and selectivity of the flotation process. Cationic reverse flotation of hematite is a common method for selective separation of quartz from iron ores to produce pellet feed. The presence of coarse quartz particles in the tailings and fine hematite particles in the concentrate are two major challenges in the reverse flotation of hematite (Vieira and Peres 2007)."

Jan 1, 2018