Search Documents

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

By Joshua A. Bennett

"Lawsuits where owners allege their property has been damaged by nearby blasting routinely costblasting companies, explosives engineers, and others in the field both time and money. When ownersfeel the vibration of a blast, they immediately begin to look for damage and usually find cracking thatwas, in fact, present prior to the blasting occurring. When those owners begin to talk to their neighbors and legal counsel, blasting entities suddenly have multiple lawsuits being filed as a result of the same blast."

Jan 1, 2016

By Don Z. Painter, Gordon F. Revey

Frontier/Traylor Joint Venture is presently constructing a section of the Tri-County Metropolitan Transit District of Oregon's (TRI-MET) Westside Light Rail system. This new section will extend Portland's existing transit system to the western suburbs of Beaverton and Hillsboro. The drill-blast excavations at this project include 10,000 feet of 20 foot tunnel, 18 cross passages, three shafts, an underground railway station, and a U-wall open cut. From a blast designer's perspective, this job has been extremely challenging. Blast vibration is limited to 0.5 ips at 200 feet or at the nearest structure, and airblast is limited to 129 dB -- linear peak and 96 dB -- C scale. The tunnels pass under heavily built up areas and have top of tunnel to surface cover distances as low as 70 feet. Surface blasting in the 26,000 cubic yard U-wall excavation was limited to five short nighttime periods due to its proximity to the very busy highway 26.

Jan 1, 1995

By Alexander Hauck, Dimitri Jung, Uli Leiste

This paper describes results from small scale tests conducted to determine the distribution of impulse on target plates when subjected to loading due to the detonation of a buried mine. The tests were conducted with saturated sand, dry sand, and water as the loading media. Tests were conducted for flat plates and for plates with angled bottoms. Previous testing has shown that angled bottoms can reduce the total vertical impulse delivered to the vehicle significantly. Different stand off distances were investigated as well as loading of the targets both on center and off center. It is very important to know not only the total impulse delivered by a detonating charge but also how this impulse is distributed over the bottom of the vehicle. A complete understanding of specific impulse will permit those parts of the vehicle, taking the greatest amount of loading, to be sized properly. Experimental results were compared to analytical expressions provided by Westine and Tremblay.

Jan 1, 2010

By John E. Wiegand

"We will attempt to explain the basic workings of a modern seismograph and how the recorded data can be interpreted, not only for determining compliance to the regulations, but also in determining whether or not a seismograph record is accurate and valid. We will discuss some parameters that should be included in all seismographic recordings. We will give examples and use overhead slidesto show examples of both accurate and valid recordings, and tampered and inaccurate seismograph recordings. Much of the information presented will be basic in nature, and will reflect the opinions and personal experiences of the author. We ho'pe the listener will gain valuable information concerning the use and interpretation of seismographic data, as well as find interest and sometimes humor in the examples shown."

Jan 1, 1992

By Brian Wingfield, Greg Williams, Richard W. Givens

Application of required energies into the rig design can have a dramatic impact upon productivity. Computer modeling of these production variables has led to changes in design with values closely approaching actual field data. Knowledge of these required energies can also specify the proper drilling technique to the application. With this knowledge, productivity-to-cost ratios can be determined with the most efficient option chosen.

Jan 1, 1995

By Constanza Bujes, Mark Jones, Graham Crook, Yansan Jamyanbaatar, Sedat Esen

Tracking ore characteristics such as grade and hardness from its original position into the material handling and processing stages remains one of the key challenges in open pit mining of hard rock deposits. The most efficient technique for rock fragmentation and separation of ore from waste is blasting, which induces changes in the grade distribution by displacing the in-situ ore into a diggable muck pile. Material movement defines the post-blast grade distribution, which is key to optimising the value of the ore and accounting for ore loss and dilution. Techniques to directly measure the displacement in open pit mining have been implemented routinely and have provided calibration and validation data for blast models to build upon. The JK Value-Based Ore Control blast movement model (JKVBOC) is the latest development of a series of research studies into blast movement and ore control at the Sustainable Minerals Institute of the University of Queensland. The blast model discretises the bench into blocks, defines the initial velocity of each block based on the blast design, confinement and explosive properties, and simulates the displacement using a physics engine. Calibration and validation of the model has been performed in open pit hard rock mines in Australasia in diverse confinement conditions. This paper describes the calibration and validation of the blast movement model against direct measurements of blast movement and final muck pile shape for a case study where the displacement of multiple shots was modelled for an open pit mine, with an analysis of the implications for ore loss and dilution. A key finding in this study is the need for further integration of this technology into the existing systems for ore control, and the potential for applications in tracking ore characteristics other than grade into process control.

By K B. Holm

This paper deals with the advances made at Syferfontein Colliery in the calculation and control of dragline methodology. The high capital outlay and operating cost of a dragline necessitates strict control of all aspects of the dragline operation. Before purchasing a dragline, a complete evaluation of all the parameters that can affect the viability, now and in the future, of the dragline operation needs to be completed. Such parameters as thickness of burden, material properties (swell), “castability”, pit width and pit length, etc. need to be considered.

Jan 1, 1994

By Jun Yang, Zongshan Zou, Mei Qu, Jianjun Zuo

For technical renovation of the thermal plant, one frame structure workshop of 50,000 m2 (59,800 yd2) construction area and one reinforcement concrete chimney of 150m (492 ft) height shall be demolished by blasting at same time. The engineering environment of which is complicated and the accommodation space is limited. Therefore, the collapse sequence, direction, scope of the dismantled building must be accurately controlled to ensure the safe operation of the adjacent generator unit and transformer station. By taking technical measures of theoretical analysis and numerical simulation etc., as well as research on structures collapse method and detailed delay interval, it puts forward the technology of bidirectional folded collapse of the workshop and it uniquely adopts the initiation system that combined with “half-second delay inside drilling” and “millisecond delay outside drilling”. Additionally, by using of the integrated vibration reduction technology in combination of the blasting ruins, buffer ditch and damping ditch, it has safely accomplished the demolition blasting work in high efficiency. Besides the demolition blasting vibration signal is collected and analyzed. The success of the demolition blasting will become valuable reference to other similar works.

Jan 1, 2016

By Yang Jun, Qu Mei, Zheng Yao-wu, Chi Li-yuan

Due to the necessity of the prediction of blasting seismic effect around strip mine bench blasting area, the paper provides a method to predict the blasting seismic effect by employing the superposition of seed waveform at different monitoring points. The method assumes that blasting vibration waveform per hole is similar to seed waveform at monitoring point. Therefore seismic wave consists of the superposition of the waves from all of blast holes. Firstly, via sensors multiple seed waveforms can be achieved at different distances from signature hole. Then, by using the given dose and the distance, the vibration waveform of a certain blast hole can be calculated by the corresponding seed waveforms. Finally, the initiation delay time interval per hole is added to the propagation time to the predicting point. The predictive waveform at the whole blasting area can be obtained by superimposing all of the single waveforms. Considering the vibration waveform of a single blast hole changes greatly with the distance, under different distances condition the seed wave employed to superimpose is achieved from the similar distance. The experiments demonstrate that based on the method the predictive vibration waveform and spectrum are basically consistent with monitoring results around near-field blast. Compared with single seed wave method, the superposition method of multiple seed wave is more reliable to predict the duration of blasting vibration, the peak particle velocity, dominant frequency and frequency distribution.

Jan 1, 2015

By Pierre De Pasquale, Aquilino Antonio Alvarez-Castro

Greenhouse gas emissions are now an essential issue for extractive industries. Actually, lowering of quarry energy consumption and CO2 emissions participates to answer both environmental and financial issues. The “EE-Quarry” European project, supported by the European Commission (EE stands for Energy Efficient), develops a new and highly effective modelling and monitoring Energy Management System technique to improve Energy Efficiency and move to a low CO2 emission rate in the nonmetallic mineral industry.

Jan 1, 2016

By Rob Farnfield, Ben Williams, Ashley Haslett, Diane Cartledge

Major accidents that occur within our industry are often tragic and expensive, damaging reputation and threaten the livelihood of the business. There isn’t anything in them that can be seen as positive for those that experience them. They undertake what are usually very painful, detailed and time consuming investigations to discover how the incident occurred and what needs to be done in the future to prevent similar incidents occurring. Many admirably choose to share the lessons learnt through industry organizations such as SAFEX International so that we can all have the opportunity of preventing similar incidents from occurring within our own organizations.

Jan 1, 2016

By Adam Gray, Emery Gray

State-of-the-art seismographs can be employed to assist the blasting engineer in understanding the propagation of vibration waves generated by blasting. Wave traces and frequency plots are used to adjust shot loading and timing, especially around close or near- field structures. Successful close-in blasting vibration monitoring requires careful consideration of the following: Geophone locations Mounting of geophone both on structures and in the ground Differences between ground motion and structural response This presentation will discuss methods used to control and monitor blast-induced ground and structure motions. Case histories are presented to illustrate seismic monitoring used as a tool to control vibrations and guide the blaster in the design process.

Jan 1, 2005

By Kenneth Eltschlager, Jim Ratcliff, Michael Mann, Edward Sheehan

The Appalachian Blaster Certification Delegation initiated a study to compare the consistency of measurements from blasting seismographs. Six blasts were monitored at surface coal mines in West Virginia, Maryland, and Ohio. A total of seven different makes were deployed during the tests, with as many as seven models from five different manufacturers compared during any one blast. Great care was taken to bury the geophones in identical fashion. The variations in seismograph readings were compared to the International Society of Explosives Engineers’ Performance Specifications for Blasting Seismographs. Between 4 and 125 Hertz, the ground vibration amplitudes should be within ±5% and airblast amplitudes should be ±1 decibel. For each of the three mutually perpendicular ground vibration channels and the acoustic channel, the median value of all the units was used as a baseline for comparison. The six blasts monitored had median peak particle velocities ranging from 0.42 to 3.47 inches per second (in/s) (10.7 – 88.1 mm/s) and median airblasts ranging from 124 to 135 decibels (dB). There were 46 seismograph recordings for the six blasts. Eighteen (39%) of the 46 maximum peak particle velocities varied more than ±5% from the median. A total of 138 (3 × 46) component particle velocities were recorded, with 50 (36%) of the readings varying more than ±5% from the median. For airblast comparison, 43 recordings were obtained, with seven (16%) varying more than ±1 dB of the median. Variances may be attributable to blasting seismograph differences, variations in field deployment, and relative locations of the geophones. Full waveform seismic and acoustic overlays for individual blasts showed encouraging conformity with some slight anomalies

Jan 1, 2015

By Mansour Asri, Philippe Somogy, Youssef Daffi, Amor Karim

Very few cases of Cast Blasting use in phosphate mining are reported. However, in open-cast coal mining, Cast Blasting is a common practice. And yet, the geological structure of both types of deposits is similar. Accordingly, advantages for phosphate open-cast mines are manifest, especially as future conditions of phosphate deposits fit quite well with the approach.

Jan 1, 2015

By Huang Daguang, Paulo Couceiro, Juan Navarro

Mining is typically conducted through a set of interdependent unit-operations, which commonly include drilling, blasting, digging and hauling, in order to deliver the required ore material into the comminution circuit and to remove waste rock with minimum impact in the operation. In such complex environment, the identification of critical paths, and respective interfaces between different unit-operations, are necessary to determine a sustainable long-term operational program. Facing this challenge, adaptive cost optimization strategies are required to increase productivity and revenue while minimizing potential environmental impacts. Since the overall mining efficiency can be strongly impacted by blasting outcomes, an operating method based on the searching of the ideal blast design is required in order to minimize the mine total cost of ownership. The implementation of a consistent continuous improvement program requires specific care in terms of design, control and execution of the different stages of blasting. For that, the application of the most advanced technologies for rock characterization, based on drill monitoring systems, and smart explosive products, allows the improvement and control of blast results by adapting the explosive energy distribution to the rock condition, so as to optimize the performance of downstream stages such as digging, hauling and comminution. This paper describes the application of a heuristic optimization approach, where blast parameters are used as decision variables to evaluate the potential impact of several blasting scenarios on subsequent unit operations, under the continuous ability of modelling, measuring and calibrating operational performances along of the mine cycle.

Feb 6, 2023

By Scott Scovira

All flyrock incidents have the potential to result in injuries or fatalities that can result in loss of company reputation, license to operate with clients, and bear the exposure to high cost liability. From 2007 to 2009, one NA Quarry and Construction Business experienced a series of flyrock incidents. In the Spring of 2009, this business declared that the frequency and severity of Flyrock Incidents had reached an unacceptable level. A Flyrock Elimination Program was launched.

Jan 1, 2012

By Paulo José Costa Couceiro Junior, Manuel Lopez Cano

The biggest Port of Latin America - the Santos Port in São Paulo, Brazil - has been drilled and blasted by controlled underwater techniques in order to remove around 40,000 m3 (52,318 cubic yard) of rock divided in two outcrop rocks: Teffé and Itapema. Underwater pumped explosive, in combination with small cartridges areas, was successfully used in order to reach a target depth of -15m (-49 ft) and a width of 220m (722 ft) in the navigation channel. It was the first time that a pumped explosive was used in underwater blasting in Brazil and it represents a historic benchmark for projects of this kind in this country. The main challenges faced in this project include the control of the ground vibration, due to the necessity to carry out detonations 40m (131 ft) away from the quay wall - where the passenger terminal and the 80 year-old warehouse were located – and the rush schedule available, in order to finish the underwater drilling and blasting phase before the coming cruise season. Therefore, the perfect combination of an ideal pumped product with an effective pumping system has permitted to carry out the project in a record of less time than 3 months (against to the original expected time of 18 months), with all vibration events under control as result of the special ground vibration program carried out.

Jan 1, 2016

By James W. Reil, Douglas A. Anderson, Steven L. Burchell

A total of 26 full-scale production blasts at three sites were extensively monitored with sophisticated instrumentation systems to determine the benefits of "ore. accurate detonators. The new and "ore accurate MS electric Masterdet detonator was tested against conventional detonators to determine any increase in productivity outputs. All blast design parameters between paired blasts were kept as constant as possible with the only difference being the inherent accuracy of both detonator systems.

Jan 1, 1989

By M. Ganster

Austria’s biggest supplier of oil and gas, transports gas through the West Austria Gasline for domestic consumption. In addition, the OMV also works as gas carrier and ensures the transit into neighbouring countries.

Jan 1, 2010