Search Documents

By Forrest T. Moyer

The safety record of the coal-mining industry, both anthracite and bituminous, in 1966 was improved over that of 1965 in all general measures of injury experience. The improvement was more pronounced in the anthracite industry. The total of 10,679 disabling work injuries comprised 233 fatal and 10,466 nonfatal injuries, 26 and 692 fewer, respectively, than in 1965. The number of fatalities in 1966 was the lowest annual total since complete records were started in 1910. Similarly, the number of nonfatal injuries in 1966 was lower than in any year since 1930 when such data were first collected.

Jan 1, 1969

By Frank B. Fulkerson

A study was made of the economic factors governing silver production in the Coeur d'Alene mining region, Shoshone County, Idaho. Production and other statistics were analyzed. It was concluded that if the rapid rise in the open market price that began late in 1961 continues, greater production of the metal should result from the mines of the Coeur d'Alene mining region. However, the output gain would be limited, because costs per ton of ore mined would rise as production was increased beyond optimum capacity. Advances in the price of silver would increase the size of ore reserves by making some marginal ore profitable to mine and by providing greater funds for exploration projects that might result in discoveries adding to the reserves. Output of byproduct silver from Lead-zinc mining probably will not exceed 4.3 million ounces, judging from the trend from 1946 to 1961.

Jan 1, 1964

By C. A. Herbert

This paper sets forth the hazards of accumulations of explosive mixtures of methane and air due to inadequate ventilation, the causes of which are discussed as follows: 1. Lack of well-maintained air courses. 2. Air losses due to leaky stoppings, trap doors, and overcasts. 3. Faulty mining methods. 4. Poor supervision. A modified plan of room-and-pillar panel mine development is suggested, which, it is believed, will eliminate many off the hazards of gas accumulations inherent in the present method of mine development. It is also suggested that some water-proofing agent be used on the roof of permanent air-course entries in conjunction with roof bolting to eliminate the detrimental effect of the moisture-laden atmosphere during summer and thus prevent serious roof falls.

Jan 1, 1953

By James J. Scott

Eleven workshops were held in various locations throughout the country in an attempt to reach the many diverse groups working in various mineral commodity areas and special ties. These meetings were held between March 1, 1974 and June 25, 1975. They were held under the auspices of the Bureau of Mines Contract to the University of Missouri-Rolla which was designed to help define Bureau research and development priorities. At each workshop a summary of current Bureau research and development was presented and the attendees were asked to present their ideas on what Research and Development programs should be undertaken to meet their needs locally. Participants included representatives of federal and state agencies, educational institutions, mining companies, equipment companies and other interested parties. The workshops covered under this report include lead mining in Missouri, limestone mining, coal mining both surface and underground in the midwest and in the Rocky Mountain area, iron mining in Minnesota, two top management meetings on institutional problems and, finally, a special two-day meeting on roof control.

Jan 1, 1977

By Mark Flower

A 20L ignition test chamber has been used to test suspensions of 7 UK and world traded coals in air and O2/CO2 mixtures typical of oxy-combustion conditions. The coals varied in rank from sub-bituminous to bituminous and were tested in varying concentrations from the ignition limit to 400g/m3. Following each successful test the combustion residue was collected, weighed and analysed within a thermogravimetric analyser, allowing Q factors to be estimated. The ignition limit varied slightly in air, but was mostly around the 200g/m3 level. With the exception of Coal C, which was much harder to ignite, it correlated roughly with coal rank. The ignition limit changed significantly with O2 concentration when in mixed O2/CO2 gases. Only a few high volatile coals ignited in 21% O2/CO2 v/v, and then only with a 2500 J, rather than a 1000J, igniter. An increase in O2/CO2 levels to 30 or 35% gave ignition patterns similar to those carried out in air with a further increase to 40% having little additional effect. In addition the minimum ignition concentration decreased with increase in O2. Heterogeneous combustion or gasification of the coal by CO2 appears to be confirmed by comparing weight loss results for air and O2/CO2 mixtures respectively for an equivalent peak pressure rise.

Jan 1, 2009

By Frank B. Fulkerson

A study was made of the economic factors governing silver production in the Coeur d'Alene mining region, Shoshone County, Idaho. Production and other stat is tics were analyzed. It was concluded that if the rapid rise in the open market price that began late in 1961 continues, greater production of the metal should result from the mines of the Coeur d?Alene mining region. However, the output gain would be limited, because costs per ton of ore mined would rise as production was increased beyond optimum capacity. Advances in the price of silver would increase the size of ore reserves by making some marginal ore profitable to mine and by providing greater funds for exploration projects that might result in discoveries adding to the reserves. Output of byproduct silver from lead-zinc mining probably will not exceed 4.3 million ounces, judging from the trend from 1946 to 1961.

Jan 1, 1964

By H. S. Benson

This report documents, from concept through field testing, the pan scraper Wheel Slip Monitor. The function of this device is to instantly warn the scraper operator of wheel slip and thus enable him to take immediate corrective action. Knowledgeable pan scraper people recognize that the preponderance of scraper tire damage and wear occurs during useless wheel slip when the scraper operator attempts to increase machine draft beyond what traction will allow. The resultant shortened tire life has become very expensive. The Wheel Slip Monitor reported here provides the means for relieving the scraper operator of attempting to judge wheel slip on tires he cannot see. Direct and intuitively understandable audible and flashing light warnings tell the scraper operator which wheel is slipping and also indicate the relative magnitude of the slip. Beside the Wheel Slip Monitor's patent utility as a real time operator aid, it has unique potential for application to extended term wheel slip history acquisition under field conditions. This information has never been easily available and it promises practical value in pan scraper management.

Jan 1, 1983

By A. C. Johnson

This report describes exploration, development, and exploitation methods, and summarizes costs at the Stormy Day mine, which was discovered in 1941. Several shipments of tungsten ore were made in 1944 to the Metals Reserve Company, Salt Lake City, Utah. The purchase of tungsten by the Federal Government, which began in 1951, stimulated interest in tungsten, and a successful program of exploration with participation of the Defense Minerals Exploration Administration (DMEA) indicated enough ore to warrant development of the property. Development work comprised drifting, crosscutting, and raising. Shrinkage stoping was used for mining the ore. Operations were suspended in October 1956, when the Federal Government terminated its purchase program. Total production of the mine was approximately 20,000 tons of tungsten ore. INTRODUCTION This information circular is one of a series, prepared in cooperation with various mining companies and published by the Bureau of Mines, relating to methods and costs of equipping and developing mining properties in the United States.

Jan 1, 1958

By C. H. Herty

As the problem of inclusions in steel has become increasingly important, more and more attention has been paid to the source of the oxide inclusions in steel. In killed steels the oxide inclusions are traceable to the reaction of deoxidizers with the iron oxide dissolved in the steel during the refining period of the open-hearth heat. In a large class of steel known as "rimming steel" the action of the steel during solidification depends entirely on the gas evolved, and this evolution in turn is controlled by the amount of iron oxide in the liquid steel in the mold. It is therefore of great importance to be able to determine the amount of iron oxide dissolved in steel and to devise methods for the control of iron oxide in any class of steel. The object of the present investigation was to obtain a true value of the oxygen content of liquid steel. If the steel has not been deoxidized, the greater percentage of the oxygen is present as iron oxide in solution.

Jan 1, 1932

By J. M. Singer

The Bureau of Mines investigated the threshold of dispersal of monolayers and piles of rock dust, anthracite, and Pittsburgh seam coal dust in a small wind tunnel that simulated a coal mine gallery, with the objective of preventing or limiting the formation of flammable dust clouds. The effect of selected variables on entrainment velocity was examined. Mode of entrainment and flow processes in the wake region of dust configurations were investigated by means of high-speed motion pictures. Significant results were as follows: 1. Local minimum air velocities required for dispersal were only slightly higher for shallow dust ridges than for dust particles. 2. Minimum velocities for entrainment of dust particles from smooth glass and coal surfaces increased in the order rock dust, anthracite, Pittsburgh seam coal. 3. The mechanism for dispersal of dust poles depended significantly on dust pile geometry, cohesiveness of dust, bulk density and compaction of dust, adhesive surface, and vibrations perturbing the supporting surface.

Jan 1, 1969

By G. E. McElroy

[The ventilation of development faces In nines for diluting Gas or dist concentrations and, in hot nines for providing air-motion cooling effect, by fan-pipe units discharging high-velocity steams of air close to the face, is an important phase of mine ventilation. The effectiveness of such units depends largely on the air-flow distribution between the pipe discharge and the face, n subject on which little definite information is available. A study of the air flow from grills into rooms3/ has provided some basic data, but under conditions so different from mine fan-pipe installations in development ends that the data are of doubtful application to mine installations, owing to differences in air-flow conditions.]

Jan 1, 1940

By John H. Johnson

This report covers research which is directed toward the measurement and control of underground mine diesel emissions. The report consists of three separate reports presented as Sections 1, 2, and 3. Section 1 "Emissions Measurement Apparatus" (EMA 1) discusses the selection and evaluation of instruments and procedures to be used as part of a diesel tailpipe emissions dilution and measurement apparatus. The instruments selected for gaseous pollutants are the Energetics Science Inc.* E.S.I.) 2000 for CO, the E.S.I. 7000 for NO and N02, and the Fuji ZFP5 for C02. Particulate matter is presently measured with the Celesco 1013 Smoke Opacity Meter. The raw exhaust concentration of one of these constituents is used Lo calculate the dilution ratio. Either a modified high range E.S.I. 2000 CO instrument or a Daco Products Cobra C02 instrument can be used, but neither is totally satisfactory. The study also indicated that it may he possible to increase the sample collection time from 15 seconds to the total 30 seconds over which the engine can be loaded without increasing the probability of damaging the vehicle hydraulic systems. Section 2 "The Effect of Fuels, Catalysts and a Filter Trap on Drift Pollutant Concentrations" discusses research in the Mine Air Quality Laboratory. A Wagner ST5D LHD with a Deutz F8L714 engine was used to compare three exhaust aftertreatment devices and a muffler-only system. The effect of these four systems on CO, C02, NO and N02 and on total, soluble, sulfate, and solid particulate matter was measured in the drift and on the LHD. The filter trap successfully reduced particulate matter for both fuels without significantly increasing the concentrations of any of the other constituents. The PTX catalyst was effective in reducing CO, and soluble particulate, but significantly increased N02 and solid and sulfate particulate matter. The Oxy Cat catalyst tested didn't seem to he working on the gases, and it significantly increased sulfate, soluble arid solid particulate concentrations. Section 3 "Diesel/Coal Particulate Matter Characterization by Laser Raman Spectroscopy" covers basic research on a method for determining the percentage by weight of diesel particulate on a filter containing a diesel-coal mixture. Signal-averaged Raman spectra provide the necessary precision. The method developed is non-destructive and uses as-received filters requiring no sample manipulation. Particulate with diesel contents in the range of 10 to 50% by weight have been analyzed with accuracies better than 6%t of the mean value. A number of samples containing diesel-coal mixtures were characterized by the procedures developed and the results are analyzed in light of various spectral and other system variables including coal rank and form and diesel engine operating conditions.

Jan 1, 1982

By D. Ng

A facility to evaluate the fire endurance of mine stoppings was constructed by the Bureau of Mines in the multiple entry section of the Bruceton (PA) Experimental Mine. Stoppings up to 6 by 18 ft can be tested in a manner simulating mine conditions. The stopping is subjected to a 70-min liquid fuel tray fire with an energy output of 75,000 Btu/min. The stopping and adjacent areas are instrumented with thermocouples and heat flux gauges. Data acquisition is by an automatic data logger capable of continuously recording over 100 channels of information. Two 8-in-thick concrete block stoppings and a galvanized steel stopping were tested. A crack developed on the fire side surface of the block stoppings where the flames were most intense. However, the temperatures of the unexposed surfaces of the stoppings never exceeded 800 C and the surfaces were undamaged. The steel stopping retained its structural integrity during the test. The temperature of the unexposed steel surface reached 5000 C, but combustible materials located 1 ft from the surface did not ignite. A 3/4-in-thick coating of construction plaster was applied to the fire side of the previously tested uncoated steel stopping. The quantity of heat energy transmitted across this coated metal stopping was reduced approximately 50%. All stoppings prevented the passage of flame and smoke.

Jan 1, 1988

By D. J. Dollhopf

This research was part of an effort to investigate means of reestablishing non¬polluted hydrological systems in areas where surface mining directly impacts shallow ground-water resources. Chemically undesirable overburden material was selectively backfilled with the intent that it would be below the future root zone, be above the reestablished aquifer, and would not be leached as a result of deep percolation. After 2 years the buried material remains above the spoil aquifer and below the maximum rooting depth. Unsaturated water flow from the land surface to the buried material occurred during wet climatological periods. No significant leaching of buried material was observed, however. Overburden sample contamination from drill stem joint grease with Pb, Zn, and Cu additives caused substantial error regarding DTPA extractable trace metals. A grease with teflon and talc additives was recommended for use in future sampling programs. DTPA extractable trace elements in overburden material had no statistical relationship to post-mine ground-water quality. Overburden columns leached with water produced leachates comparable to overburden and spoil ground-water trace metal quality. A depositional model described the Rosebud Coal overburden as a fluvial system with distinct units of sand, silt, and clay, with distinct chemical properties. Physical and chemical characteristics of the model were comparable to the in situ geochemical system, a relationship which may aid in locating overburden materials unsuitable for reclamation.

Jan 1, 1979

By M. M. Wong, J. E. Klosterman

Scrap beryllium chips ( nominally 96 to 97 percent Be ) were electrore fined in a prototype cell with 408 lb of electrolyte composed of 52.4 mole - percent LiCl , 36.3 mole - percent KC1 , and 11.3 mole - percent BeCl2 . The cell temperature was 500 ° C. In a typical 10-3 /4 - hour deposition cycle , 0.415 pound of metal was produced ; the metal contained impurities in parts per million as follows : C , 700 ; 0 , 610 ; Al , 34 ; Ca , 32 ; Cu , 20 ; Fe , 25 ; Mg , 9 ; and Mn , 23 . Operation of the prototype cell for 2 years demonstrated that adapting the electrorefining process to an enlarged scale of operation presented few difficulties in mechanical functions , maintenance of optimum operating conditions , and control of product purity . After the spent anode feed was leached in a 5 - percent nitric acid solution and the fine - sized particles were removed , it was recycled in some tests . The metal produced was somewhat higher in impurities than metal from the fresh scrap chips .

Jan 1, 1964

By P. J. Remington

Field measurements utilizing a seat pad accelerometer were made on 25 underground coal mining machines in order to quantify the vibration levels experienced by the operators. Those data were combined with information on the statistics of the operating times of those machines in order to compare the operator's vibration exposure to the criteria in ISO 2631, "A Guide for the Evaluation of Human Exposure to Whole Body vibration." The comparison showed that about 30% to 40" of all underground coal mining machine operators can be expected to be exposed to vibration exceeding the fatigue decreased proficiency criterion, whereas only 10 to 15% would be expected to experience vibration exceeding the exposure limit. The primary sources of the exposure are shuttle cars and possibly scoop trams. Detailed exposure statistics are presented and the implications of the results are discussed.

Jan 1, 1983

By Harold E. Marr

A simple algorithm is presented for processing digitized X-ray spectra obtained with a Si(Li) or Ge(Li) semiconductor detector coupled to a multi- channel analyzer. The simplified least-squares procedure is used to smooth out the statistical fluctuations in the spectrum by repeatedly fitting a quad- ratic equation to a predetermined number of channels and performing a traveling smooth across the spectrum. A logarithmic transform is applied to the raw data to minimize the distortion of the gaussian-shaped peak profiles. The efficacy of the technique is evaluated by observing the distortion of several gaussian-shaped peaks that have been subjected to the smoothing operation. The locations of maximums and minimums in the spectrum are predicted in the process as well as the values of the peak heights. The convolution integers from a least-squares fit of a quadratic equation are calculated as part of a FORTRAN subroutine. The building-block approach to computer programing in a small laboratory is discussed.

Jan 1, 1972

PRODUCTION of cesium, cesium salts, and rubidium salts in the United States declined somewhat from 1961 levels; rubidium production was virtually unchanged. Imports of pollucite declined because consumption was supplied partially out of inventory. Domestic Production.-About 50 tons of pollucite was reported mined at the Tin Mountain mine in the Black Hills of South Dakota. The Dow Chemical Co., Midland, Mich., MSA Research Corp., Callery, Pa., and Penn Rare Metals, Inc., Revere, Pa., produced a total of 159 pounds of cesium. Rubidium production remained essentially the same as in 1961. Shipments of the two metals by these companies and by American Potash & Chemical Corp., Trona, Calif., totaled 279 pounds. Production of cesium and rubidium salts by American Potash & Chemical Corp., Penn Rare Metals, Inc., and Rocky Mountain Research, Inc., Denver, Colo., declined substantially during 1962.

Jan 1, 1963

By SUMNER S. SMITH

Mine inspection in Alaska by the Federal mine inspector was somewhat handicapped during 1915,the inspector having to spend a large part of the summer and fall in examining the Matanuska coal field in connection with the designation of the Government reservations and the leasing units in that field. However, in addition to>this work, the mines in southeastern and southwestern Alaska were inspected by both Federal and Territorial inspectors, a considerable number of men near the Federal inspector's officeat Juneau were trained in first aid to the injured and in the use of mine rescue apparatus, the mines of the interior and of Seward Peninsula were inspected by the Territorial inspector, and a suit was brought in the name of the Territorial inspector for the nonreporting of serious accidents under the Territorial inspection law. The work of the Federal inspector was handicapped also by a lack of field assistants. This condition is likely to be serious, as preparations have been made for opening the Matanuska, Bering River, and Nenana coal fields, and a number of permits granting the free use of 10-acre tracts in other fields throughout the Territory have been issued. The need of a comprehensive inspection law and experienced engineers to safeguard the opening of coal mines by operators who are not familiar with coal mining and are using inexperienced help is obvious.

Jan 1, 1917

By Ronald W. Schaefer

This report describes operations at the Rosiclare Fluorspar Works of the Aluminum Co. of America at Rosiclare, Hardin County, Ill. The works include the Fairview mine, the fluorspar mill, and related facilities. The publication covers exploration, development, mining and milling practices, mine-drainage problems, and other activities and is presented as part of the Bureau of Mines series of publications on mining and milling practices in various parts of the United States. The Rosiclare fluorspar area, for its size, has been the largest producer of high-grade fluorspar in the United States and probably in the world. The vein system in this area is over 5 miles long and 1/2 mile wide, and ore has been found as deep as 900 ft.

Jan 1, 1961