Search Documents

By Sally A. Shoop

Thirty-seven blasts have been monitored using either three or four seismographs, at four coal strip mines and at a limestone quarry. Statistical analysis of the data shows that square-root, cube-root, and site-specific scaling methods predict peak particle velocities with about the same (low) degree of reliability. Some mines have peak particle velocities that are significantly lower or higher than the U.S. Bureau of Mines averages (Siskind et al., 1980). This suggests that the option provided by the proposed regulations (Office of Surface Mining, 1983), to adjust blast designs based on site-specific measurements could be highly beneficial both to operators and to the public. The frequency spectra reveal that the predominant frequencies were generally less than 50 Hz but several blasts had a significant amount of energy up to 125 Hz. In some cases the vibration energy was concentrated at frequencies corresponding to the delay intervals.

Jan 1, 1983

By J. A. Organiscak

The Bureau of Mines recently investigated dust generation and methane liberation during half-and full-web cutting at a double-drum shearer longwall face. This study was conducted to ascertain the health and safety aspects of wider web shearing at longwalls. Results from these underground tests showed that deeper web cutting reduced dust generation and methane liberation per ton of coal mined, while significantly improving shearer production rates. When cutting with the airflow (head-to-tail cut pass) full-web cutting decreased dust generation per ton by 16 pct at the shearer and 6 pct at the tailgate, with an increase in shearer production rate of 72 pct. Methane liberation per short ton also deere~sed by 36 pet at the shearer and 22 pct at the tailgate. Full-web cutting against the airflow (tail-to-head cut pass) decreased dust generation per ton by 41 pct at the shearer and 37 pct at the tail-gate over half-web cutting, with an increase in shearer production rate of 61 pct. Methane liberation per ton also decreased by 35 pct at the shearer and 41 pct at the tailgate. These improvements for full-web cutting are a reflection of improved cutting efficiency (less dust and methane produced from cutting) and less new face area exposed per ton of coal mined (less methane liberated from face per short ton of coal mined).

Jan 1, 1988

This publication summarizes, for all interested parties, the research, development, and demonstration in-house projects programed by the Bureau of Mines for fiscal year 1979 (October 1, 1978--September 30, 1979) under its Nine Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's miners.

Jan 1, 1979

Minerals are a fundamental component of the Nation" material and economic base. Without a continuous supply of minerals to meet growing and changing needs, the basic character of our society would be very different. The importance of minerals to the United States was reemphasized by the Congress in I970 when it enacted the Mining and Minerals Policy Act, which stated that it is the continuing policy of the Federal Government in the national interest to foster and encourage private enterprise in (I) the development of economically sound and stable domestic mining, minerals, metal and mineral reclamation industries, (2) the orderly and economic development of domestic mineral resources, reserves, and reclamation of metals and minerals to help assure satisfaction of industrial, security and environmental needs, (3) mining, mineral, and metallurgical research, including the use and recycling of scrap to promote the wise and efficient use of our natural and reclaimable mineral recources, and (4) the study and development of methods for the disposal, control, and reclamation of mineral waste products, and the reclamation of mined land, so as to lessen any adverse impact of mineral extraction and processing upon the physical environment that may result from mining or mineral activities.,.

Jan 1, 1977

By P. M. Johnson

A design for a laser-powered optical interferometer, using a specimen whose thermal expansion is to be measured as part of the optical system, was conceived and applied in a prototype dilatometer. The object of thin work was the development of an absolute dilatometer capable of use at elevated temperature, particularly above 1,000° C. The prototype has been operated at temperatures exceeding 1,510° C. Results obtained with this device agree within 2.5 percent with the published data for the coefficient of expansion of columbium.

Jan 1, 1968

By Stephen R. Iverson

The U.S. Bureau of Mines made an economic appraisal of the Buttermilk study area, Inyo County, California in October 1980. Results of surveys indicate no potential for metallic, non-metallic, or energy resources in the area. However, glacial till covering most of the area prevented bedrock examinations by the appraisal teams or earlier prospectors. No mining claims are known to be in the area. INTRODUCTION Present Studies The U.S. Bureau of Mines, Western Field Operations Center, searched county mining claim records and other data available concerning mineral deposits, claims, leases, production, and mining activity in the area. The Bureau conducted field work in October 1980 searching for prospects and claim locations. Fourteen reconnaissance lode and placer samples taken from the area were analyzed for gold, silver, and tungsten; a spectrographic analysis also was run on selected samples.

Jan 1, 1981

By R. J. Campbell

[The steady increase of aluminum production means a corresponding increase of carbon consumption in the alumina-reduction cells. Improved petroleum techniques constantly reduce the amount of byproduct petroleum-coke production. These, trends threaten the alumina-reduction works with possible shortages of carbon, which must be supplied from some other source. In anticipation of this shortages, an investigation into the possibility of using coal as an alternative source of carbon was begun at the Northwest Experiment Station of the Federal Bureau of Mines. The investigation lit has developed bench-scale methods that produce carbon of higher purity than is required by specifications for anode carbon. Additional work will b required to bring these processes to pilot-plant seals and to prove the suitability of the carbons, produced or aluminum-anode consumption.]

Jan 1, 1956

By Richard H. Bares

The general or macroclimate of the study sites in western North Dakota is characterized by rapid and sometimes extreme daily and day-to-day temperature fluctuations, rainfall patterns which are erratic in spatial and temporal distribution and intensity, generally low relative humidity, plentiful sunshine, nearly continuous air movement, and a relatively short frost-free period. Of particular relevance to plant growth and productivity is the mosaic of microclimates: these microclimates are affected by landform (convex and concave surfaces); exposure; slope angle, length and aspect; soil color, texture and surface cover (litter), and vegetation cover. The most critical plant growth governing factor in this region is available water. It is determined principally by water input (precipitation) and water loss (evapotranspiration) which is increased by high temperatures, wind, and poor litter and vegetation cover. While spring and fall precipitation is generally gentle and soil-soaking summer rains frequently come in the form of intensive, soil-washing, localized convective thunderstorms of short duration. Due to the convective nature of these storms, summer rainfall is particularly affected by regional topography; southwest slopes and crests often receive more rainfall since these storms usually move in a northeasterly direction. The water loss due to runoff and consequent soil erosion arc major problems resulting from such "cloudbursts". Previous fall precipitation (September - October) when added to current seasonal precipitation (March - August) was found to be significantly correlated (r-.93) with plant production. Winter precipitation (snowfall) is relatively light as the prevailing weather is dominated by dry polar air masses from the north. The nearly continuous wind is responsible for removing snow from open exposures and depositing it in depressions and windbreaks. Although the winter precipitation is not a large component of the total annual precipitation, conservation of that which does occur would contribute to plant production during the following growing season. Generally clear skies over the region facilitate receipt of abundant sunshine at the earth's surface. While good for early season soil warming and plant photosynthesis, this abundant sunshine coupled with long days and nearly continuous wind is responsible for evapotranspiration exceeding precipitation by an average of six inches between June' and September. On a local (micro) scale, the water deficit is most severe on the southern exposures which receive the most direct (most effective) solar radiation and therefore are warmer than other exposures. On a broader scale, it was found that ambient temperature extremes were slightly but significantly greater in the town of Beulah in the Knife River Valley than at the upland test sites, This may have been due to the difference in topography and/or the "urban heat island" effect. It is known that air temperatures in large cities may be 2° to 4°C higher than that of the surrounding countryside. It is also well known that basins, depressions or valleys are sinks for cold air masses and are often subject to frosts not occurring on adjacent upland sites.

Jan 1, 1982

By Phillip N. Yasnowsky

This Bureau of Mines publication tabulates State taxes levied on nonfuel minerals that have the characteristics of a severance tax.

Jan 1, 1978

By Thomas J. Peters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 17,320-acre portion of the 52,143-acre Little High Rock Canyon Wilderness Study Area (CA-020-913/NV-020-008) in order to evaluate its identified mineral resources. The study area is located in Humboldt and Washoe Counties, NV, about 42 miles north from Gerlach. Three areas of epithermal alteration, similar to alteration associated with disseminated gold deposits, were found in the study area. One of the areas occurs along a northeast-trending structural lineament. Southwest of the study area two gold prospects undergoing active exploration, as well JS a gold deposit being prepared for production, occur along the same lineament. The Bureau of Mines examination, however, did not find evidence for gold resources in the study area.

Jan 1, 1987

By H. E. Powell

Basic data were recorded on the decompositions that take place during thermal decomposition of siderite (FeC03). Both the naturally occurring and a synthetically prepared mineral were studied by differential thermal, thermo-gravimetric, X-ray-diffraction, and chemical (including gas) analyses. Thermal decomposition was studied in the media of dry air, moist air, dry carbon dioxide, dry helium, and dry carbon monoxide and at atmospheric and at reduced pressures. Results showed the thermal decomposition of FeC03 to be an extremely complex process, dependent on environmental factors and side reactions that cannot now be completely controlled. Therefore, full understanding of the reaction involved must depend on additional research with advanced evaluation techniques.

Jan 1, 1965

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of raining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENT The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

By M. Zaki El-Sabban

Tables of chemical thermodynamic properties for the ideal gas state from 0° to 1,000° K are reported for eight alkanethiols, three cycloalkanethiols and arylthiols, six thiaalkanes, two dithiaalkanes, three thiacycloalkanes, and three thiophenes. They are based on current physical and thermochemical constants and definitions, reliable vibrational assignments, and the latest insights into molecular structure and energetics.

Jan 1, 1970

By Scott Turner

I have been asked to speak briefly about recent progress in the mining industry of the United States, and to touch on the general advancement of en- gineering science as applied to mining. By recent, I shall mean within the past 20 or 30 years. Such a period includes a great many of the changes which are of particular interest to the present generation of engineers, and the undergraduates of today will hardly turn back farther than the beginning of the present century in their study of develop- ment of methods and processes. Also, my own professional life spans this period, and I have seen or have been aware of most of these developments as they were taking place. In my review of developments, for the sake of simplicity and clarity, I shall deal separately with improvements in metal mining, coal mining, mechanical and electrical machinery for mines, metallurgy, petroleum engineering, and safety practices. Under each of these headings I have set down what appear to me to be the outstanding changes brought about during the past 2 or 3 decades. Other points will occur to other engineers; I do not represent that the following re- view is complete; it is only intended to be suggestive. In general, improvements in mining and metallurgical practices have come gradually, the charges being effected little by little, simultaneously in widely scattered places, and through the experience and inventive genius of many men. These changes have has small beginnings, and are generally the cumulative result of many steady and unsensational progressions, which still continue. What we today might be inclined to consider the culmination of a series of betterments in mining is, of course, but an instantaneous phase of developments which will continue in the future at even a more rapid pace than they have in the past. We are looking at but a flesh of a moving picture, with an endless reel to come after we finally leave the theatre. Behind all the changes in the mineral industry, the driving force has been the increasing demand of an expanding population for more metals and minerals with which to advance civilization. More people, with an increasing per capita consumption, together with the exhaustion of the richer but smaller, and more

Oct 1, 1930

By Russell E. Griffen

With the development of larger mine-haulage trucks in recent years, the visual field of the driver has diminished correspondingly. Specifically, the operator's lack of direct vision in the right front area and directly to the rear constitutes a serious hazard to personnel in nearby small utility vehicles. Recently developed electronic technology has made it possible to supplement the use of mirrors and fresnel lenses to warn the operator of specific collision dangers in the truck's blind areas. This Bureau of Mines report describes the results of a coordinated contract and in-house research program to develop and test in-mine prototype electronic systems to detect the presence of smaller vehicles within the blind areas of large mine-haulage trucks. Each system utilized transmitters installed on the smaller vehicles and receivers installed on the haulage trucks. Transmitting techniques tested included both low-and high-frequency radio waves. On-vehicle testing established the engineering feasibility of each approach. Further private sector product development to improve reliability and reduce system costs is recommended. Mining companies should consider the advantages of each type of system.

Jan 1, 1988

By John F. Papp

The objective of this U.S. Bureau of Mines study is to calculate an accurate, reliable estimate of chromium and nickel content of stainless and heat-resisting steel produced in the United States. The columbium, manganese, molybdenum, titanium, tungsten, and vanadium contents of this steel are also calculated. Such contents are required for estimating the quantity of alloying element recovered from recycled stainless steel and consumed by market sectors. In this investigation, the elemental fraction of stainless and heat-resisting steel was calculated as the ratio of the weight of element contained in stainless steel to the weight of stainless steel produced. The elemental fraction has been calculated as a time-averaged, grade-averaged value. The elemental fraction was averaged from 1962 through 1983, and averaged over the grades for which production was reported by the American Iron and Steel Institute during that time period. The 1962-83 average elemental fraction of U.S.-produced stainless and heat-resisting steel was calculated for chromium to be about 0.17 ± 0.01; columbium, 0.00014 ± 0.00003; manganese, 0.015 ± 0.005; molybdenum, 0.004 ± 0.001; nickel, 0.07 ± 0.01; silicon, 0.009 ± 0.001; titanium, 0.0004 ± 0.0001; tungsten, 0.0001±0.00003; and vanadium, 0.00003±0.0000l.

Jan 1, 1991

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on Manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By A. C. Fieldner

This is the tenth annual report of research and technologic work conducted by the Bureau of Mines on the occurrence, properties, mining, preparation, and uses of coal and coal products. These annual reviews are guide's to the current work-and publications of the Bureau but do not replace the more complete reports published under the authorship of the individual investigators on specific problems in Bureau of Mines bulletins, technical papers, reports of investigations, and information circulars and in the technical press. The Annual Report of the Director of the Bureau of Mines to the Secretary of the Interior for the Fiscal Year ended June 30, 1945, summarizes the year's work on coal as follows: Coal and Coal Products The United States maintained its No. 1 industrial position in supplying fuel for war and in preparing for peace through more complete mining, improved preparation and up-grading of coal for special uses, and better utilization of coal in industrial establishments and homes.

Jan 1, 1946

By James Westfield

Following is a brief resume of the Division's activities that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority under Executive Order 9728 was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1961