Search Documents

By Hugh D. Pallister

Alabama probably has the most extensive deposits of high-grade flake graphite in the United States and was the largest producer during World War I. Therefore, with the outbreak of World War II, users of flake graphite turned again to Alabama to supply their requirements. Flake graphite is the most important ingredient contained in graphite crucibles used in melting crucible steel and special alloys essential for war purposes. Early in World War II the Army and Navy placed flake graphite on the list of critical war materials. During World War I, when the supply of Ceylon graphite (then in demand) was cut off, large quantities of flake graphite were produced in Alabama, and about 40 mills were built. Most of these were abandoned after the war when imports of the cheaper Madagascar flake (which gradually replaced Ceylon graphite) began to reach this country. With the beginning of World War II, the Madagascar supply was cut off', and consumers were again compelled to look to domestic sources for their supplies. They found only one small mill in operation, that of the Ceylon Graphite Co. in Coosa County, Ala. The Bureau of Mines made a preliminary examination of the Alabama flake graphite deposits in 1940. Samples were taken and tested at the Southern Experiment Station at Tuscaloosa.

Jan 1, 1948

By G. A. Smyres

The Bureau of Mines investigated a HCI-02 leaching procedure to recover Cu, Ni, and Co from a low-grade bulk sulfide flotation concentrate prepared from the Duluth gabbro complex. Since the Duluth gabbro complex is the largest known and unexploited Ni resource in the United States, the development of options for extracting the metal values from the flotation concentrate of this domestic resource is necessary. Conditions were determined for producing a pregnant solution low in Fe to facilitate recovery of the metal values. Leaching experiments were conducted at 15 pct solids, 1000 to 1200 C, 0.2 to 0.3 g HCI per gram concentrate in a 50-gal reactor pressurized to 50 pSig with 02. Base metal extractions from the concentrate were, in percent, 90 to 92 Cu, 99 Ni, 97 to 99 Co, and 0.1 .Fe. Precious metals extractions were erratic and unpredictable; at best their extractions were, in percent, 55 Au, 90 Ag, 40 Pt, and 45 Pd. The reaction time at 1200 C was 0.5 h. The use of compressed air instead of 02 as the oxidant was also investigated. Solvent extraction using LIX 622 was used to remove Cu from the pregnant solution. Cementation on Cu was tested for precious metals recovery, while sulfide precipitation was used to produce a Ni-Co product. A conceptual flowsheet for treating the Duluth gabbro concentrate is proposed.

Jan 1, 1985

By Patricia R. Devine

This appendix documents the mathematical approach to deriving the components of change presented in this report. The formulation closely follows that contained in Chapter IV of the documentation for the BEA 1977 Input-Output Tables.' The basic elements for the calculations include the "use" matrix (U), the "make" matrix (M), and any of the ten columns of final demand (generically represented by the symbol y). The use matrix contains information about changes in the technological processes of production, while the make matrix describes the nature of secondary product production in each industry. We adhere to BEA conventions in maintaining careful distinctions between commodity output (c) and industry output (x). The industry-by-industry 1-0 tables supplied by NYU for use in this analysis are square matrices, with the number of commodities and the number of industries both equal to 85. The BLS table for 1982 (commodity by industry) was aggregated and adjusted to be consistent with the earlier tables. The three basic steps for estimating components of change proceed as follows for each column of final demand. 1) Calculate the actual change in output of each commodity for each of the four time periods: 1963-72, 1972-77, 1977-82, and 1963-82.

Jan 1, 1988

By Francis E. Federspiel

Silver and gold are the principal metals in the study area; they occur in quartz veins or silicified portions of shear zones. In some deposits, lead, antimony, zinc, and molybdenum are associated with gold and silver. A uranium-bearing buried stream channel lies near the southern boundary. Since 1850, more than 300 lode claims and relocations have been recorded mainly in the southeast corner of the study area (fig. 1). Complete mine production records are not available; however Clark (1977, p. 28) reported less than $300,000 of gold and silver were produced, mainly from the Exchequer, IXL, and Pennsylvania Mines. Other mines in the area probably yielded are before 1900, but early records are not available.

Jan 1, 1981

Consumption and intensity of use trends for twelve metals, by industrial end use, were estimated for 1972 through 198Z. The trends were then forecast through 1993 using standard statistical methods. The intensity of use measure selected is the quantity of metal consumed per constant dollar output of a specific industrial sector. The metals studied were aluminum, chromium, cobalt, copper, lead, manganese, nickel, the platinum-group metals, tin, titanium, tungsten, and zinc. Average annual growth rates for the following four of the twelve metal increased from 1972-82 as follows: aluminum, 1.00 percent; platinum-group metals (consisting of platinum, palladium, and iridium), 8.83 percent; titanium, 7.82 percent; and tungsten, 6.09 percent. Consumption. for the remaining eight metals decreased at average annual rates ranging from 0.58 percent (copper) to 5.37 percent (manganese).

Jan 1, 1986

By D. Harrington

The number of fatalities from mine explosions for the fiscal year 1945 dropped below that of the year before; continued improvement over the record of the years from 1940 to 1945 is hopeful, but the number of reported explosions has increased rather than diminished, and the number of victims claimed by explosions is often more definitely a factor of chance than forethought. Mine fires and explosions can be eliminated through the methods now well-known to those well-informed in matters pertaining to safety in mining but ignored by many coal-mine operators and employees who follow procedures of the past or their own short cuts, regardless of disasters that may result: Tried and proved safety measures for preventing mine fires and explosions have been recommended to the mining public repeatedly, yet only a relatively small but far-sighted minority have adopted these measures and made them a part of operating practice. That far more explosion disasters did not occur in 1945 is fortunate. In 1945 a coal-mine fire of electrical origin caused heavy loss of life, while several others from the same cause were controlled with but few fatalities; this hazard is now being curbed temporarily to some degree after the bad record of the two preceding years, but a real solution of the problem has not been reached, although cooperating committees trying to produce at least some answer have made progress.

Jan 1, 1946

By J. R. Cobble

As part of the Federal Bureau of Mines project to develop new or improved materials for metallurgical furnace applications, the Tuscaloosa (Ala.) Research Center has conducted research to develop a reproducible laboratory test for evaluating the resistance of refractories to molten slags. Tests were conducted with a slag representative of slag used to produce mineral wool. A rotating cylindrical furnace was lined with the brick being tested, and it was operated at temperatures up to 1,660° C for periods ranging from 8 to 32 hours. The effects of such variables as slag temperature, rotational velocity, charge rate, and contact time on refractory erosion were determined. The research demonstrated the reproducibility of the test procedure developed.

Jan 1, 1980

By E. D. Calvert

This Bureau of Mines report discusses the electric-arc reduction of zirconium and hafnium oxides with carbon yielding a metal-metallic carbide mixture. The carbon to oxide ratio in the feed determines the metal to carbide ratio in the product. A sample of this product was produced -or testing as a feed for the deBoer iodide-dissociation process. A new technique for producing pure carbides is described, which uses the intense heat of the arc to volatilize the carbide. The condensed vapor form , crystals of nearly stoichiometric carbide, INTRODUCTION This research examines the preparation of refractory metal carbides in the controlled atmosphere electric-arc furnace.

Jan 1, 1962

By Raja V. Ramani

The potential usefulnuss of reclaimed surface-mined land has received much attention in recent times. This attention is partially due to the establishment of federal environmental reclamation standards but concern for achieving better land uses has also been shown by interested members of the mining industry. In an effort to develop a procedure for evaluating postmining land use potentials, specific mines in various regions of the U. S. were studied to determine the extent of current mined-land planning and to discover characteristics that are regional in nature. As part of this investigation, a 430-acre surface mine in Clear-field County, Pennsylvania has been studied. Established site planning principles have been applied to the case study site including formation of a data base, development of alternate land use plans, and evaluation of the economic, environmental, and social impacts of the land use alternatives. Key factors affecting site realization have been identified along with positive suggestions for applying land use planning processes to mined-land planning.

Jan 1, 1983

By Koehler Stout

Many hydraulic backfills are deposited at low density and provide less than optimum support strength to stope walls. This laboratory study shove that fill strength can be considerably increased. Placement methods used to increase the fill strength were the head, vibratory, cementation, double-planed (dblplod), and combinations of these methods. An experimental facility van designed to study the placement cathode and resultant strengths of the fills. Physical property tests made on the fills included laboratory penetration and vane shear plus several supplementary tests, such as grain size distribution and relative density. Test results were compared to fills planed by conventional methods and to those results reported by other investigators. When compared to fills placed by conventional methods, the penetration modulus was increased by 4.3 tines when the uncemented-vibrated-head concept was used and 71 times when the cemented-vibrated-head-dblplod concept was used. Apparently, hydraulically fill strength can be substantially increased. Conceptual mining plans are also included on suggested ways of placing and using high-modulus backfills.

Jan 1, 1979

By G. M. Martinez

The Bureau of Mines has investigated methods for the recovery of byproduct heavy minerals from sand and gravel operations in Oregon and Washington. These heavy minerals are not currently recovered except for gold in a few areas. The recovery of byproduct heavy minerals would provide a domestic source of minerals presently imported, and a more efficient use of domestic resources would be accomplished. Samples from more than 40 locations were treated by gravity separation to yield heavy mineral concentrates (black sands). Magnetite, ilmenite, zircon, rutile, chromite, platinum-group minerals, radioactive minerals and gold were identified in the concentrates. Individual zircon, ilmenite, chromite; magnetite, and gold products were recovered from selected concentrates by low-and high-intensity magnetic, high-tension, and heavy-medium separation techniques. The recovery for the individual mineral products ranged from 67 to 95 pct.

Jan 1, 1981

By D. Harrington

The code of hoisting signals for use in mines hoisting from one level, as suggested in this publication, is submitted to induce consideration of this subject by representative groups of the coal-mining industry, such as the lithe Inspectors Institute of America, National Coal Association, American Mining Congress, and others, as well as to -furnish a code of signals for use in those mines operated in States that do not have regulatory hoisting codes in their mining laws, or regulations. The signal codes described in this publication apply only to mines hoisting from one level and to slope mines. Mines that hoist from more than one level are referred to Bureau of Mines Information Circular 7289 Suggested Hoisting-Signal Code For Metal Mine Shafts, which suggests signals for hoisting from various levels or stations.

Jan 1, 1944

By Ernest A. Curth

The Bureau of Mines and Old Ben Coal Co. concluded a cost-sharing contract in 1975, the objective of which was to demonstrate the Herrin No. 6 coalbed in southern Illinois can be mined safely by longwall methods. Under the agreement, three longwall panels are to be mined at Old Ben No. 24 mine. A premining investigation laid the groundwork for specifying a roof-support system designed to control hazardous ground. Old Ben Coal Co. and Bureau engineers selected lemiscate-type roof shields. A rock mechanics program and geological mapping provide early warning capability and criteria for future equipment design. The effect of mining on the surface was monitored by a surface survey to develop subsidence-prediction criteria for the Illinois coal basin. The first of the three longwall panels started up in September 1976 and was completed in May 1977. The major adverse condition was the occurrence of limestone concretions, called coal balls, in massive pods. The shields provided adequate roof control even in faulty ground. Operation of the second panel started on August 1, 1977, following panel-to-panel transfer of the equipment. The accident rate was low.

Jan 1, 1978

By Gary L. Stecklein

This final report delineates the findings of the test programs, simulations, and analyses performed to determine the requirements for the effective application of berms and guardrails as truck restraint systems for elevated mine roadways. Included arts criterion for effective vehicle restraint for guardrail applications and recommendations for berm applications based on scale model tests and computer simulations. Full scale haulage vehicle-berm interaction field tests were performed to correlate the results of these model tests and computer simulations. Recommendations for the construction of berms were made on the basis of tests of berm bearing strength, response of the vehicle to different berms, and predictions based on the obtained correlation

Jan 1, 1981

By Daryl R. Tweeton

The Bureau of Mines is investigating possible applications of geophysics to monitor leachate during in situ mining. Tomographic reconstruc-tion of seismic or electromagnetic crosshole data appears applicable. The tomographic program BOMTOM (Bureau of Mines tomography) was written and then used to investigate reconstructions with synthetic travel time data. The calculations confirmed that without constraints, crosshole data do not provide unique solutions. The solution is not determined solely by the data, but is also influenced by the velocity guesses starting the iterative solution procedure. The effectiveness of constraints in combatting nonuniqueness was examined. The requirement that the velocity not vary laterally at the top and bottom of the pixel grid was effective. This constraint is realistic when the top and bottom of the grid represent dry and saturated re-gions, respectively. Limiting the maximum velocity improved reconstructions, but may not be applicable in practice. BOMTOM uses the simultaneous iterative reconstruction technique (SIRT) with straight ray paths. The program is efficient in use of memory, and can be run on a personal computer. A source code in FORTRAN is listed. A source code in BASICA and compiled executable codes in both languages are available from the Bureau's Twin Cities (MN) Research Center.

Jan 1, 1985

By Thomas C. Atchison

The purpose of this Bureau of Mines investigation was to measure the amplitude and shape of the strain pulse and the size of the crushed zone produced in a granite by different explosives and to determine how these quantities are related to the detonation properties of the explosives. The reflection theory of rock breakage has shown that the amplitude and shape of the strain pulse incident at a free surface determine the fragmentation and volume of rock broken. Determination of the properties of an explosive that control the characteristics of the strain pulse produced in the rock will help in evaluating explosives for use in blasting. The investigation showed the different explosives produced a twofold variation in the amplitude of the strain pulse but little variation in the shape of the pulse. The explosives also produced a twofold variation in the volume of the crushed zone, but differences among the explosives were more accurately determined by strain-amplitude measurements than by crushed-zone measurements. The peak amplitude of the strain pulse and the volume of the crushed zone correlated with the calculated detonation pressure of the explosive.

Jan 1, 1959

By Efrem R. Reeves, David C. Byrne

This study was conducted as part of a project involving the evaluation of a new type of noise exposure monitoring paradigm. Laboratory tests were conducted to assess how “nonstandard” dosimeter microphones and microphone po­sitions measured noise levels under different acoustical condi­tions (i.e., diffuse ?eld and direct ?eld). The data presented in this article re?ect measurement differences due to microphone position and mounting/supporting structure only and are not an evaluation of any particular complete dosimeter system. To varying degrees, the results obtained with the dosimeter microphones used in this study differed from the reference results obtained in the unperturbed (subject absent) sound ?eld with a precision (suitable for use in an ANSI Type 1 sound level meter) 1/2 -inch (12.7 mm) measurement microphone. Effects of dosimeter microphone placement in a diffuse ?eld were found to be minor for most of the test microphones/locations, while direct ?eld microphone placement effects were found to be quite large depending on the microphone position and supporting structure, sound source location, and noise spectrum.

By Roger L. Baer

Marine disposal of mill tailings has been practiced worldwide for over a century. However, only recently have the environmental effects of marine disposal been systematically studied. Some early attempts at marine disposal of tailings resulted in adverse impacts to marine life. However, recent advances in tailings disposal methods have included the introduction of engineered submarine tailings discharge systems, advanced environmental assessment and monitoring methods, and oceanographic modeling systems. Successful submarine tailings disposal (STD) has occurred at several mines. The U.S. Bureau of Mines (BOM) has undertaken studies of the disposal of mining and milling wastes in the marine environment. The BOM Alaska Field Operations Center, Juneau, initiated a review of the technology, regulations, and economic aspects of STD. The review illuminated the need for organization of literature on the subject, therefore the Bureau compiled this extensive bibliography on marine disposal of mill tailings. The bibliography presented here contains 1483 references and is also available through diskette in the Word Perfects format. A review of the references indicates that literature on submarine disposal inadequately covers the subject. The majority of the references listed only peripherally relate to the subject. Published literature on the engineering and environmental aspects of STD is severely limited.

Jan 1, 2011

By J. Bruce Clemmer

In the experimental concentration of Vermont talc-magnesite ores, talc concentrates and tailings rich in magnesite were obtained. On account of the possible market value of the magnesite, the tailings are given consideration' in this report along with the talc. After some comments about the talc industry, the magnesite that accrued as tailings will be considered. Then the flotation results will follow.

Jan 1, 1936

The condition of the domestic mining industry is obviously affected by the cycles in general business conditions. This study, the results of which are presented in a series of 78 charts, attempts to examine the interrelationships between the general business indicators and the major statistical measures for the base-metals industries during the cycles in the United States economy following World War II. For these industries the cyclical problem is perhaps less acute than the secular-trend problem. However, short-run fluctuations in production and employment do have very important impacts upon the welfare of the regions which derive a significant portion of their income from base-metals mining and processing industries. Any information concerning the normal patterns of development as the industries enter into a cyclical recession will permit better forecasts and perhaps help promote measures to alleviate the distress that occurs. Also, a systematic study of the comparative movements among the statistical measures during a series of cycles can bring to the fore the economic causation involved, and perhaps, after intensive study, can lead to a better method of short-range forecasting for these industries. This study has not fully achieved these aims. However, observations which significantly aid the interpretation of the current monthly statistics on these commodities are made, and some very general conclusions are drawn. The charts are presented so the interested people can examine them and draw additional conclusions. The charts refer specifically to cyclical analysis. The technique of indexing each cycle to its turning point effectively subordinates the longer term trend movements of the data. Thus, certain general conclusions flowing from this study and from the continuing economic research of the Office of Chief Economist will aid the reader by clarifying the frame of reference within which the charts should be examined.

Jan 1, 1961