Search Documents

By W. R. McDonald

Part of the U.S. Bureau of Mines mission is to supply the U.S. mineral industries with information that is useful in planning to meet the Nation's critical and strategic mineral needs if a national emergency occurs. The Bureau conducted laboratory research including operating a nominal 100 lblh pilot plant to demonstrate the recovery and concentration of chromite by gravity and flotation operations from three northern California mineral deposits. Gravity beneficiation test results show that concentrates contained as much as 52 pet chromic oxide (CrZ03) with recoveries of about 80 pet. Results from the bench-scale unit operations of mineral liberation, tabling, vanning, spiraling, pinch sluice, work index, and thickener area determination tests are presented in this report.

Jan 1, 1990

By W. M. Myers

[Utilization of small stone is recognized as one of the important problems of the lime industry. The term ?small stone' is used to designate material that is too small for calcination in tie shaft kilo. The maximum dimension A such stone rosy be placed at four inches. The introduction of any considerable quantity of stone having demensions lee: than this into the charge of a kiln impedes the draft and readers successful operation of the kiln difficult on impossible. Attempts design a shaft kiln which would calcine stall stone satisfactorily have not been successful to date. Thousands of tons of this small stone arc produced daily, and while part of it finds a market, for it has many uses, the profit is usually small an competition is teen and prices are low. Production of the material is, however, so greatly in excess of market that surplus of hundreds or possibly thousands of Jose axe place daily in stock piles and classified as waste. in a few instances a fortunate combination of circumstances, such as a program of or other work requiring large quantities of concrete aggregate, may mate it possible some quarries to market this stone later at a profit, teat in general the chances A profitable utilization are slight, and the quarry operator has the expense of handling this waste stone and providing a storage site for it. The brittle nature of limestone makes it impossible to quarry the stone and crush, it to size suitable for the shaft kilns without producing an excess of undesirable fines. Elimination of fines by changes in quarrying or crushing practices cannot lee expected. On the contrary, the adoption of more modern methods of quarrying in recent years has increased the proportion of small material. The tendency is to blast the roan with large charges of explosives and crush it with mechanical crushers, which produces more fines than the older methods of careful blasting with small char yes and sledging the rock by hand.. We increasing use of underground mining of limestone has also increased the production of small stone, as blasting in the confined space of an underground stope shatters the rocs more completely than quarrying in the open. The use of the very friable limestones, such as the limestone of Florida for the manufacture of lime adds a new factor to the calcination of small stone. These friable lime limestones have a low tensile strength and crumble in the kiln, causing trouble. Successful calcination of these stones is accomplished in specially]

Jan 1, 1926

By D. T. Holmes, W. G. Sandell

"INTRODUCTION Three representative lots of ore wore obtained from the Aguila minim district in Arizona during the Bureau's exploration of manganese deposits there. Since only selectively mined ore from this district will meet commercial-grade specifications, the ores were studied to determine their amenability to concentration.Although the purpose of the investigation was to determine the possibilities of the district as a source of commercial-grade manganese, testing was sufficiently comprehensive to indicate the response of the ores to several different types of treatment. Many data of secondary importance have been omitted, end only the more pertinent tests are presented in detail.At the beginning of the investigation of manganese-ore beneficiation in December 1940, the only product marketable to. Metals Reserve Company was ferro-grade manganese, grade B, the requirements for which follow: Mn, min., 48 percent; Fe, max., 7 percent; Si02, max., 10 percent; P, max., O.18 percent; Al12O3, max., 6 percent; Zn, max., 1 percent.Later the specifications were modified gradually. As of May 15, 1943, manganese products were acceptable if they contained over 35 percent manganese and less than 3 percent zinc and 1 percent phosphorus. Prices were based upon material containing 48 percent manganese, 6.O percent iron, and. 11 percent silica plus alumina. Premiums were paid for manganese con¬tent over 48 percent and iron content under 6 percent, penalties being imposed upon products containing loss than 48 percent manganese or more than 6 percent iron or more than U. percent. silica plus alumina.. The specifications for commercial manganese further required that the maximum particle size be 12 inches and that 75 percent of the product be coarser than 20-mesh. Therefore, fine material, such as table and flotation concentrates, had to be nodulized or sintered. In addition, carbonate manganese ores were not acceptable unless calcined.."

Aug 1, 1948

By Michael G. Pojar

This Bureau of Mines report estimates the population of the principal types of machinery in use by the coal mining industry during 1982 in surface and underground mines. Estimates were arrived at using 1976 coal equipment population estimates as baseline data with modifications made for new mine development, expansion, and closure occurring during 1976-82. Estimates were broken down into 3 regions which included all 26 coal-producing States. Modifications made to the baseline data were computed using (1) actual equipment information when available, plus (2) equipment information hypothesized from representative generic mine models, which were predicated on mine size and mine method. Roughly half of the equipment fleet at new or expanding coal operations was known; the remainder was hypothesized. The mine models used to generate equipment information are included in this report, along with the hypothesized equipment use data. The equations and various factors used to determine the equipment adjustments for mine closings, new mine openings, and small coal mine operations are also identified.

Jan 1, 1986

By G. L. Oldright

The Metallurgical Branch of the Bureau of Mines, as a part of its duties under the Organic Act, works to prevent wastes in industry and to disuse inmate information on the fundamentals of metallurgical processes. During the war, the necessity of large production was increasingly emphasized. Such duties necessitate from time to time the study of units of full commercial size, the operation of which is beyond the facilities of the Branch. When developments have reached this stage; work has been continued in cooperative agreements with operating companies that have been willing to contribute the use of their plants and staffs and to allow the publication of the results obtained for the common good of the industry.

Jan 1, 1948

By Annie G. Smelley

As part of its program to develop technology that will encourage maximum utilization of the Nation's mineral resources, the Bureau of Mines conducted research on debrining potash-clay waste slurries by means of flocculation with a high-molecular-weight polymer and subsequent solid-liquid separation on a rotating trommel screen. In laboratory batch tests, potash-clay waste slurries were consolidated from initial clay contents of 8 pct to final contents of 30 pct with a polymer dosage of 1.2 Ib/ton of dry clay waste. Small-scale continuous tests yielded debrined products containing 20 pct solids using a polymer dosage of 1 Ib/ton of dry clay solids.

Jan 1, 1983

By Arne Landsberg

A study of the chlorination kinetics of germanium, silicon, iron, tungsten, molybdenum, columbium, and tantalum has been made to determine the effects of temperature, chlorine concentration, geometric surface area and gamma radiation. The reaction products were volatile at the temperatures used this making it possible to follow the reaction rates by weight loss of the solid. Chlorination rates of germanium, silicon, and iron were found to be directly proportional to chlorine concentration while the rates for tungsten, molybdenum, columbium, and tantalum were proportional to the 0.5 to 0.6 power of chlorine concentration. A good correlation of reaction rate and geometric surface areas was not obtained because the true surface area of the samples could not be measured. Intense gamma radiation had no effect on reaction rates. The Arrhenius activation energies determined over the temperatures used are as follows: Germanium, 27 kcal/mole (233°-241° C); silicon 33 kcaL/mole (375°-517° C); iron, cold rolled, 20 kcal/mGle (259°-325° C) annealed, 21 kcal/mole (293°-337° C); tungsten, 43 kcal/mole (617-776° C); molybdenum, 37 kcal/mole (445°-4910 C); columbium) 34 kcal/mole (229°?255° C); and tantalum, 29 kcal/mole (370°-449° C).

Jan 1, 1965

By Dhanesh Chandra

[The U.S. Ucparunent of tlIe III LeriOr, Bureau of 1?Ilnes, lnta dcvcltil- (I a m.?tl,nd to extract nickel, i:ob.tll and IlIIicr Valuc:l,1, mrl?tl., lrom I.ow grad:, dumusI it Inlet itc.: :isin;; a rarb-i mnnnxid:: reducl.iun and ,innnonln/mumonlum sull,h.Ito Icitcll Col lowed by solved. evil let foil and clot tr:,winnfu,;. 'I 'o rain bcLtur undcI'sLandin;; uI the producLs reduced rind leached with the s;:Item, the liureau of t?Ilite; was enf,ngod In a 1 uinL sl.utly IIt1I the Uuttvcr ltc~:c:n-ch LnstiI-IL-. 'I'hr'ut;;h C(Im:drlod ahplit I¬L ion:; of a rotnbIW)L11nl ill eleu Lyon :utJ uplical inicrnscopy, cle trun beau micru,inal?;st?s and X-r.iv tcchnitlaes, Lhc factors jilt] ucncing low nickul e::lracl.on yLrids Iron, ccrlnin l;tteritos wul the hcuefhe al yCferL front addil.I:un u1. r:u)plowt' ruug,ounus and halides have bucn rrvealod. IL leas ht'en shown their nt nliJcrate Lion terlperuLuri's (5S0°C - 6501C) Lhe 111LACl extraction ylolds were low hccausc of the futmetlt-m of rufrill t,urv sillc:Ite compicxcs during ciii lit Hi [hut COOL.tlu sig nlficnnt anutunls of nickel .Lrui LhaL arc resistant Lu discolullull it, a su6r.C?quent ammnnlIca1 Jcaeh. 'This formation ill rulracLorv rnngtieves is altrlbuU?d Lo the prc.srnCV of aluauinum combined with c.ilicun jn addlt.lon In tnnl;neni~im in I.lic Lalerites, Iligb exII.Ictlon yields were oblalneJ when none or only a few I ,fraCLot' e, were InrmeJ. Hit s;intc rcfrarlnry cowl, Icxc5 also lend Lo surround Ow IaaIIiable meI.allle iron-IIIcI:el :iILoy CIUSisling ill the mau'ix, tIll: rrhv nreveu)Ling cuntacr ,Itlt LI5U Jeacl: solution; this, huwrvcr, ran ho ovu:rcoml by At ti itlon .111.11 retieCtiun. 'I'hc eIIcc l of prr.reJIctlun .,Ill itivi's vucli i's lye iii', ',udlum "Ill orIde, hv,Irogrn CIIInrILIC, etc., and Lht? 1111,Lre:InrLlI'll he'e:tleg un Lbe cxLt,icLitin are also iilsr.ussod 111 Lhe rcl,olt.]

Jan 1, 1979

By Arthur V. Petty

In Bureau of Mines research on recycling chrome-containing refractory wastes, used refractories from argon-oxygen decarburization and electric steelmaking furnaces were beneficiated. By means of dry magnetic separation on minus 6-mesh crushed wastes, a concentrate was produced. After minor adjustments to the particle size distribution, full-size refractory brick were dry-pressed by a commercial producer and fired to 1,450° and 1,730° C. Standard testing procedures were used to determine the cold-crushing strength, modulus of rupture at 25°, 1,300°, and 1,500° C, hot load, thermal shock resistance, thermal expansion, and slag resistance. Optical and electron microscopy were used to determine grain-bonding mechanisms, and energy-dispersive analysis of X-rays was used to determine elemental distribution. The test results indicate that the beneficiated material could be used to produce a refractory product suitable for moderate-temperature applications.

Jan 1, 1982

By W. C. Hudson

"Sillimanite, kyanite, and andalusite are aluminum silicates having the same chemical composition (Al2Si05) and are used in the ceramic industry for the manufacture of high-grade refractories. ""Natural sillimanite with added corundum or other alumina to just short of mullite 2SiO2) proportions is unequalled for jobs where strength at high temperatures, resistance to spalling, and resistance to slagging by acid slags is desired. High-grade porcelain ware also requires these minerals.""At the same cost, sillimanite would be preferred for most uses, but the lack of any large source of sillimanite has given economic preference to kyanite or andalusite for special refractories and high-grade porcelain ware.""3/The possible economic value of the sillimanite schist in the piedmont Plateau was first recognized by Dr. L. L. Smith, of the University of South Carolina, who published an article in the Engineering and Mining Journal, August 1943, on an occurrence of sillimanite schist in South Carolina.The Bureau of Mines was interested in developing a large source of sillimanite to relieve the shortage of high-grade refractories, and initiated a project to locate the ore-bearing areas in Georgia and South Carolina and to develop the most favorable ones.Two hundred and seventy-eight outcrops of sillimanite-bearing schists were found by a Bureau of Mines engineer.4/ The schist occurs irregularly throughout a belt extending from Talbot County, Georgia; to Spartanburg County, South Carolina, about 220•miIes long and approximately 15 miles in maximum width. The Bureau drilled four areas of the more coarsely crystallized schist in Georgia and South Carolina:In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon; chief; conducts preliminary examinations, performs the actual exploratory work; and prepares the final report. The Metallurgical Branch;.R. G. Knickerbocker; chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Sep 1, 1946

By Forrest T. Moyer

The safety record of the mineral and mineral-fuel mining and processing industries in 1966 was improved slightly for the second consecutive year as indicated by reduced injury-frequency and injury-severity rates. The overall operating activity was higher in 1966, as measured by the increased number of men working and the total man-hours of worktime. Injury Experience.-The rate of occurrence of all disabling work injuries in the mineral industries was 17.38 per million man-hours in 1966. This overall rate comprised frequencies of 0.28 for fatal and 17.10 for nonfatal work injuries, compared with respective rates of 0.28 and 17.26 in 1965. Fatalities totaled 543; 5 more than in 1965. The total of 33.091 nonfatal injuries was 291 higher than in 1965. However, the larger number of disabilities was offset by the increased worktime in 1966. so that the fatality frequency was unchanged and the nonfatal frequency rate decreased from 1965.

Jan 1, 1967

By Thomas Curtin

The Bureau of Mines, in its researches aimed to prevent wastes and to increase efficiency in oil-well practice, has investigated the matter of casing troubles and fishing methods. The results of the investigation are set forth in this paper. After expensive development work, many wells being drilled for oil have been abandoned because of casing troubles. These troubles in many instances have been thought to be insurmountable, whereas they are sometimes susceptible of solution. In fields_ where casing difficulties are of daily occurrence, methods have been evolved for combating them. Were these methods more widely known and applied wherever the same conditions exist, the oil industry at large would be greatly benefited. This report attempts to classify these troubles and suggests solutions that will save the operator discouragement and expense. It is assumed throughout this paper that the reader is so familiar with the ordinary oil-well drilling and fishing methods that detailed explanation is unnecessary. The well-drilling terms that are used herein will be readily understood by those for whom this discussion is intended. However, in order to avoid confusion as to the sense in which some of these terms are applied, definitions &re included.

Jan 1, 1920

By Robert J. Evans

The Bureau of Mines is sponsoring a variety of long-term, high-risk research to advance state-of-the-art technology in U.S. underground coal mining. This report reviews the status of many Bureau projects that support fundamental underground coal mining operations; the project areas include cutting coal from the solid (extraction), hauling coal from the face (transport), and activities that sustain daily operations (logistics). Innovative equipment and technology have been developed, with these major objectives: to significantly improve coal mine productivity, to further advance coal recovery and personal safety within the mining industry, and to reduce the time needed to develop longwall panels. The majority of the prototype equipment covered in this report either has undergone or will undergo comprehensive evaluation at Bureau surface test facilities so that performance and reliability can be improved before the equipment is tested and evaluated in a working section underground.

Jan 1, 1988

By James W. Wade

This paper describing the mining practices at the Tintic Standard mine is one of a series being prepared by the United States Bureau of Mines. In the preparation of this paper each subject has been presented by the engineer in charge. L. R. Dobbs wrote the part pertaining to tae technique of square-set mining, J. M. Snow the part on geology, and M. D. Paine, the part on ventilation. All of the drawings are the work of H. W. Waterfield of the engineering department. The statistics of the Tintic district ware prepared by A. G. MacKenzie. Each writer has attempted to show the difficulties that arise in operating and the practices used to overcome them.

Jan 1, 1930

By L. Bruce McDonald

This Federal Bureau of Mines publication is a statistical analysis of all surface and underground coal mine fires reported in the United States from 1950 to 1977. Accounts of selected nonreportable fires and opinion data gathered via interviews with mine safety directors were separately analyzed. Both reported and nonreportable fires were analyzed by time trends, State, ignition source, burning substance, location in mine, equipment, detection, duration, injuries, fatalities, and successful extinguishing agents. It was found that the majority of all mine fires were electrical in origin. The equipment most frequently involved in underground fires was conveyor belts, and in surface fires, it was crushers and/or breakers. Underground fires occurred most often near the working face. Water and hand-portable extinguishers were the most common methods of extinguishment.

Jan 1, 1980

By J. D. Davis

THIS report gives results of an investigation of the carbonizing properties of the following eastern Kentucky coals: Elkhorn No. I bed, No. 28 mine, Wayland, Floyd County; Elkhorn No. 2 bed, Turner No. 5 mine, Drift, Flood County; Leatherwood (Haddix No. 5) bed, Leatherwood mine, Leatherwood. Perry County; and Harlan bed, Path Fork mine, Path Fork, Harlan County. The carbonizing properties were determined by Bureau of Mines-American Gas Association (BM-AGA) tests at 800° and 900° C. and by expansion tests in the sole-heated oven. Plastic properties were determined by tests in the Gieseler and Davis plastometers. The coals were tested singly and as blends with 20- and 30-percent low-volatile Pocahontas No. 3 coal. The dry, mineral-matter-free, fixed-carbon content of the carbonizing samples ranged from 56.7 percent for Elkhorn No. 2 to 59.7 percent for Leatherwood, and the heating values on the moist, mineral-matter-free basis ranged from 14,420 B. t. u. per pound for Elkhorn No. 2 to 14,720 for Harlan. The percentage of ash ranged from 2.9 to 6.1. The fluidity of three coals, measurer. In the Gieseler plastometer, ranged from 230 to 670 dial divisions; the fluidity of Elkhorn No. 2 could not be determined by this method. Blending lowered the fluidity of each coal; the fluidity of the blends containing 20 and 30 percent Pocahontas No. 3 ranged from 16 to 53 and from 8 to 17 dial divisions, respectively. Agglutinating values determined on silicon carbide-coal mixtures in the ratio 15:1 ranged from 3.8 to 6.3.

Jan 1, 1952

By Leonard Obert

The ultimate object of this investigation is to develop a method for determining the pressure, in- situ, on rock mine pillars, arches, end other mire structures. The preliminary investigations of Bureau of Mines engineers, as well as those of other investigations4/ have shown that, the velocity of sound depends on the pressure if it is dependent to such an extent that a measurement of the velocity might be used as a means of determining the pressure, a sonic method of measuring the pressure on rock mine columns is possible. Briefly the method would require, first, laboratory determination of the variation of the velocity of sound with pressure in samples of rocks taken from mine pillars to establish a. velocity-pressure relationship for the type of rock and, next, measurements of the velocity of sound in the mine pillars from which the laboratory samples were taken. The pressure on the pillars could be determined by correlating the velocity in the pillar with the velocity-pressure relationship established in the laboratory. Obviously the success of the method depends on the extent to which the velocity of sound varies with pressure in rock.

Jan 1, 1939

"INTRODUCTION Early in 1936 the Interstate Oil Compact Commission and other groups interested in forecasts of demand for petroleum requested the Bureau of Mines to make a physical inventory of crude-oil stocks in the United States, Accordingly, the 74th Congress appropriated funds for conducting such a survey during the fiscal year ended June 30, 1937. In the discussions and hearing 2/ relative to the need for the survey, the opinion was expressed that crude oil held in storage for long periods had lost so much of its gasoline content that the economic significance of total stocks should be discounted materially. Therefore, a primary objective of the survey was to make a physical inventory of the crude oil held in storage above ground and to determine the quantities and characteristics of the light fractions contained in the various stocks."

Sep 1, 1938

By Leonard Obert

The ultimate object of this investigation is to develop a method for determining the pressure, in situ, on rock mine pillars, arches, and other mire structures. The preliminary investigations of Bureau of Mines engineers, as well as those of other investigators,4/ have shown that the velocity of sound depends on the pressure if it is dependent to such an extent that a measurement of the velocity might be used as a means of determining the pressure, a sonic method of measuring the pressure on rock mine columns is possible. Briefly the method would require, first, laboratory determination of the variation of the velocity of sound with pressure in samples of rocks taken from mine pillars to establish a. velocity-pressure relationship for the type of rock and, next, measurements of the velocity of sound in the mine pillars from which the laboratory samples were taken. The pressure on the pillars could be determined by correlating the velocity in the pillar with the velocity-pressure relationship established in the laboratory. Obviously the success of the method depends on the extent to which the velocity of sound varies with pressure in rock.

Jan 1, 1939

By O. T. Barrett, R. F. Aberethy, H. N. Cooper, Thomas Fraer, William L. Crentz

"INTRODUCTION The object of the techniques described in this report is to determine the possibilities of separating the components of a raw coal into such grades as may be necessary to recover some exceptionally clean functions for special purposes.To do this commercial gravity methods would require separation at very low specific gravities, entirely outside the range of conventional practice. Hence, a technique has been developed for breaking down cool ample, into very close fractions within the gravity range of the (-lean coal matter as well as for separating it from the refuse and particles.Such data on the fundamental specific-gravity consist of the clean-coal matter will serve to appraise the difficulty of the problem and to chow be accomplished if and when effective methods of making such separations commercially are developed."

May 1, 1945