Search Documents

By R. A. Franks, G. F. Friel, J. C. Edwards, L. Yuan

Five mine fire experiments were conducted in a 2.08m high and 2.90m wide, ventilated mine entry in the National Institute for Occupational Safety and Health (NIOSH)'s Safety Research Coal Mine (SRCM) to determine the effect of the dispersion of carbon monoxide (CO) on mine fire detection. CO measurements were made at distances from 7.6 m to 45.2 m downwind from the fire with diffusion mode CO sensors positioned near the roof. For small intensity fires, less than 30 kW heat release rate, generated by 14 kg coal in a 0.61 m square tray, it was determined that air flow and sensor spacing were significant for fire detection at the 10 ppm CO alarm level. Within 15.0 m downwind distance from the fire, 10 ppm CO alarm values occurred for volumetric air flows less than 11.5 m3/s. However, the 10 ppm CO alarm value did not occur 30.0 m downwind from the fire for air quantities greater than 6.2 m3/s due to dilutive mixing of the CO in the air stream. The criterion that the mine fire alarms occur within 15 min of the onset of flaming combustion could not be consistently met with the 10 ppm CO alarm. This suggests the use of lower CO alarm values, or reduced CO sensor spacings for mine fire protection. It is demonstrated how computational fluid dynamics (CFD) can be used to model the CO dispersion downwind from the fire in support of a plan to optimize sensor spacings.

To improve the air quality in large-opening stone mines by developing better ventilation techniques, including appropriate fan selection in conjunction with air-coursing methods. Background Stone mines are the most common underground large-entry mines in the United States. Data from the Mine Safety and Health Administration (MSHA) for the year 2000 indicate that there were 162 active nonmetal underground mines in the United States, of which 117 were stone mines. Many underground stone mines are drift mines developed from previous quarry operations. Typically, these room-and-pillar mines have entries that are 20 ft or higher and at least 40 ft wide. These large dimensions lead to a very small ventilating pressure loss, even when significant air quantities move through the mine. This is especially true of drift mine operations where ventilating pressure losses of <0.25 in w.g. are common. Underground stone mines with shafts that are<200 ft deep typically have ventilating pressure losses that are <2 in w.g. The pressure losses through these mines are much lower than those of a typical coal mine or deep metal/nonmetal mine. Therefore, the ventilation techniques and principles are quite different. In addition, because of new MSHA regulations that limit the concentration of diesel particulate matter, these mines may need to greatly increase their ventilation airflow. Therefore, large-opening mines need a fan that can move large air quantities and operate at low static pressures. There are three fan types for mine ventilation: centrifugal, axial vane, and propeller. Centrifugal fans are uncommon in underground stone mines as they are often associated with mines requiring the highest of ventilation pressures. Axial vane fans are widely used in all types of mining operations. They are the most common fan type currently found in underground large-opening stone mines. However, they typically do not operate at low static pressures with high efficiency. Propeller fans are currently uncommon in underground stone mines. They are designed for low static pressures and large air quantities at higher efficiency. This fan type best suits the ventilation needs in large-opening stone mines?they produce large air quantities at low pressure losses. Mines with air shafts<100 ft long and at least 12 ft in diameter have fairly low mine static pressures and may also benefit from propeller fans.

Dec 1, 2002

By Brian P. Stapleton, Bill M. Stewart, Joel R. Warneke, Curtis C. Clark

Of the 28 accident/injury classifications listed by the Mine Safety and Health Administration, handling materials is second only to roof falls in terms of generating the highest number of reportable accidents in active underground coal mines. Two materials-handling activities that cause numerous injuries each year are the categories of “handling supplies or material, load and unload” and “moving power cables.” Mechanization and mine worker activity training are two methods that can aid in preventing these injuries. This paper describes three mechanical methods—the mobile manipulator, the in-mine hoist, and a cable-handling system—being developed and tested at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Two of the devices are specifically designed for loading, unloading, and moving supplies and materials, and the third device is for handling trailing cables in the confined spaces of coal mines. Also described are safety solutions developed for underground coal mines geared to showing miners safe and unsafe ways of performing various materials-handling tasks.

By D. J. Dollhopf

The specific objective of this three year study is to investigate the means of reestablishing non-polluted hydrologic systems in areas where surface mining directly impacts shallow ground-water resources. The research area chosen for the study is located near Colstrip, Montana it a new mine site where chemical analysis of core samples from the overburden suggested that excessive concentrations of several elements would he encountered during the mining process. This report discusses local vegetation; soils; and regional geology, and hydrology. Stratigraphic cross sections and regression analyses were used to study the litho-chemical relationships in the overburden. Cross sections indicated Inimical material may be related to both rock tune and position within the overburden profile. In overburden zoness where clay content was high, there was a greater probability that Pb, Cu, Ni, and Mn concentrations would also be higher than average; similarly, the likelihood of overburden exceeding a suspect level became less as the sand content increased. Highest value, of conductance were usually found within a few meters of the surface. High concentrations of clay, nickel, and zinc were frequently found directly above and below the Rosebud coal. Regression analysis indicated overburden SAR was predictable with only a Na analysis. A strong relationship also existed in the overburden between conductance, Ca, and Mg.

Jan 1, 1977

By L. L. NAUS, R. D. Currie

Hazards in connection with the use of compressed-air jets for ventilating gassy mines are given little consideration by most mine officials largely because compressed air is considered the safest means of transmitting power for operating various types of mining machinery, and the inherent dangers in its use for this purpose are virtually negligible . The installation of compressed-air lines in coal mines leads to the utilization of compressed air for ventilating working places , with the result that , although the primary ventilation systems may be adequate to meet existing needs , proper conduction of normal ventilation has been neglected , so the working faces receive only a small amount ofthe total air circulated through the mine . Reliance in part on compressed air or other auxiliary means for ventilation is always attended by danger that gas will accumulate , due to intermittent operation , and the tendency is to operate auxiliary schemes only. during the working shift ( or possibly only part of the shift ) and to dispense with them during off- shifts or at times during the working shift when gas may accumulate because of lack of ventilation . When the men come on shift the auxiliary ventilating device often may be started without a preliminary examination of the working place , or .. the examination may be made sometime before the oncoming shift arrives , the gas being allowed to accumulate in the meantime. This may result in uncontrolled movement of a body of gas if proper precautions are not taken . Several mine explosions have been caused by the movement of a known body of gas by compressed air into the haulageway, where it was ignited by an arc from a passing locomotive . This danger is more pronounced where supervision is lax .

Aug 1, 1937

By Robert J. Timko, Charles D. Taylor, Edward D. Thimons, Tom Mal

A test system was developed for measuring airflow in the National Institute for Occupational Safety and Health (NIOSH) ventilation gallery using a three-axis ultrasonic anemometer. The gallery was used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data collected at multiple sampling locations between the face and the end of the curtain were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations, and displayed as methane distribution in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within two feet of the face.

By William H. Schiffbauer, Timothy Lutz, Michael R. Yenchek

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL) participated in an experiment to facilitate the remote control of dozers used on coal stockpiles. The experiment consisted of supplementing the normal sensory cues an operator requires to manipulate the dozer from a remote location. NIOSH provided and tested a vision systems intended to give the operator the ability to operate the dozer safely and efficiently from a remote position. This paper highlights the genesis of the experiment, identifies the contributions of Consol Energy and Caterpillar, and details the NIOSH efforts and successful test results. Keywords-remote-control; vision system; stockpiles; safety

By R. L. Zick, J. D. Byars, T. P. Mucho

Recently, a large Pittsburgh seam longwall mine was nearing depletion of a major portion of its current reserves and had begun to develop in a different direction from its original portal area to access additional reserves. This meant that a large area of the mine would be abandoned and sealed. However, continued use of the original mine portal area required that the water accumulating in the abandoned mine would eventually need to be pumped to the surface. This would be in addition to the discharge water associated with the new portion of the mine. Several pumping and sump options were investigated to handle the quantity and quality of the anticipated discharge water. This paper describes some of these options, their advantages and disadvantages, and the final engineering decisions. Some problems and unanticipated outcomes, as well as the eventual solutions are discussed, including: (1) estimates of pump requirements, (2) water pool size, (3) eventual water quality, (4) anticipated inflows, and (5) integration into the overall mine water system.

By R. Mark, R. Richards

The Washington National Cathedral is one of the largest masonry structures in the USA, and like many of its European Gothic counterparts, it required nearly a century to construct. The design was altered during this period, resulting in greater loadings than were originally anticipated on the soil beneath the foundation. When signs of continuing differential settlement were observed in the early 1990&apos;s, the Cathedral approached the US Bureau of Mines (now the National Institute for Occupational Safety and Health (NIOSH)) for assistance in monitoring the movements of the massive towers and walls. An array of dual-axis tiltmeters was installed about 40m above ground level to measure wall and tower inclination, with the data sent over a dedicated phone line to the NIOSH Pittsburgh Research Laboratory for processing. Mechanical gages and string-potentiometers are also being used to measure motion across cracks and joints, and differential pier settlement is being monitored with optical-level surveying. Data have now been collected for almost 7 years, and they show a long-term settlement trend masked by dramatic diurnal and seasonal thermal movements. The paper discusses the major findings of the study, implications for the future of the Cathedral, and conclusions regarding the use of geotechnical monitoring at major national monuments.

By Andrew B. Cecala

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36 and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 2010

By S. J. Schatzel, W. P. Diamond

High methane emissions originating from the active face areas and from the fractured formations overlying and underlying the mined coalbed can adversely affect both safety and productivity in underground coal mines. Since ventilation alone may not be sufficient to control the methane levels in the longwall mining environment, gob gas ventholes have become a standard supplementary methane control option in many mines. As mines progress into deeper and gassier coalbeds, or as longwall panel size increases, ventilation and gob gas ventholes together may not be sufficient to maintain methane levels within statutory limits. To decrease the risk associated with methane emissions under these circumstances, in-seam horizontal methane drainage is often used to reduce the gas content of the coalbed prior to mining. Horizontal methane drainage borehole completion designs, drilling strategies, and degasification lead times may need to be adjusted for site-specific conditions due to mine design, geology, and the gas content of the coalbed. This study investigates different horizontal methane drainage borehole patterns, borehole lengths, and degasification times prior to and during panel extraction to evaluate their effectiveness in reducing methane emissions using a "dynamic" 3D reservoir modeling of a 38 1-m wide longwall panel operating in the Pittsburgh coalbed. Results of this study showed that dual and tri-lateral boreholes are more effective in decreasing emissions and in shielding the entries compared to fewer shorter, cross-panel, horizontal boreholes parallel to the longwall face. Modeling results showed that after 12 months of pre-mining methane drainage, the average longwall face emission rates can be reduced by as much as 10.3 m3/min and 6.8 m3/min using tri- and dual-lateral boreholes, respectively. It was also shown that if pre-mining methane drainage time is short, it is important to continue methane drainage during the panel extraction to maximize reductions in longwall face emissions since additional face emission reductions achieved during this period can be comparable to pre-mining degasification.

By W. R. Reed, J. A. Organiscak

Haul trucks have the potential to generate large amounts of respirable dust. This respirable dust has been shown to be a health hazard to personnel, especially if it has a high silica content. Lack of dust sampling data from haul trucks prompted the completion of a study to quantify respirable dust concentrations. These field studies were conducted measuring instantaneous respirable dust at stationary locations from passing haul trucks at a stone quarry and at a coal mine site. Fugitive dust levels from haul trucks were analyzed to characterize dust dispersion. This analysis indicates safe following distances for haul trucks and other heavy equipment to avoid overexposure of respirable dust from the lead haul truck.

By Lewis A. Martin

Researchers from the Spokane Research Laboratory, National Institute for Occupational Safety and Health, in cooperation with engineers from the Department of Mining and Geological Engineering, Montana Tech, Butte, MT, conducted tests to evaluate the tensile strength, fiber count, and adhesion of shotcrete applied to panels at the Chief Joseph Mine, a research and training facility operated by Montana Tech. The tests were conducted in the mine ramp 45 m (150 ft) inward from the access portal at a 15.25-m- (50-ft) long test area divided into five 3-m- (10-ft) long sections. The shotcrete was applied with an Aliva 240.5 machine fitted with a predampener. Different amounts of fiber were entrained for each panel. Background data for the tests were obtained from earlier tests in Nevada, where the typical amount of fiber in the shotcrete is 6.54 kg/m3 (11 lb/yd3). All shotcrete was applied to a minimum thickness of 76 mm (3 in). Cylindrical cores were drilled at the wall-rock interface, and adhesion was tested after 28 days of curing. The goal of this research is to reduce the need to install multiple supports at the advancing face by creating a safer mining system that limits the time miners are exposed to unprotected roof.

Jan 1, 2004

By John J. Sammarco

Abstract- Emergency shutdown systems (ESDs) for mining machinery provide critical functions to safeguard miners. Traditionally, ESDs were realized with simple hardwired circuits; today, there is a growing trend to use programmable electronic technology such as programmable logic controllers (PLCs). This paper describes an analytical study to quantify the safety integrity of a PLC-based ESD and a hardwired ESD. The safety integrity level of each design approach was determined by quantifying the average probability of failure on demand (PFDavg) as described by the recommendations for programmable electronic mining systems published by NIOSH and the IEC 61508 international standard. The safety analyses addressed system architecture, hardware failure probability, proof test interval, diagnostic coverage, and human error probability. The results indicated that a same level of safety, safety integrity level 3 (SIL 3), could be attained when evaluating random hardware failures. Neither approach could attain SIL 3 if manual activation was used. Human error was the limiting factor where, using human reliability analysis, PFDavg < 1 x 10-1; thus, the ESD does not meet SIL 1. It is apparent that automatic verses human¬activation of the ESD is a very important safety consideration. Manually actuated ESDs can only achieve SIL 1 regardless of the technology; therefore, additional independent safety layers of protection are needed to exceed SIL 1. Secondly, it is apparent that the technology choice is very important. The PLC-based ESD was much simpler to design and to validate safety1.

Jan 1, 2007

By P. M. Sullivan

The principles and application of amalgam electrolysis to the recovery of zinc and tin from secondary products were studied; this Bureau of Mines project was one phase of investigating the development of more efficient methods for processing iron-bearing zinc and tin to produce both base metals of high purity. Zinc of 99-99-percent purity was recovered from galvanizer&apos;s dross with recovery efficiency of 98 percent. Tin of 99.9-to 99.99-percent purity was recovered from hardhead with recovery efficiency of 81 percent. Both materials were treated by the same method in separate systems. Mercury was used to leach zinc from dross and tin from hardhead to form amalgams of each metal, both of which were subsequently refined electrolytically to produce high-purity metal. Impurities that were contained in both secondary products behaved as theoretically predicted; impurities that were insoluble in mercury remained as sludge in the leaching column. Except for lead, the readily amalgamated impurities were prevented from fouling the electrolyte by the blocking action of the amalgam electrode. Lead impurity in the tin-refining system dissolved and immediately precipitated as the sulfate. The primary advantage of the amalgam refining method lies in direct recovery of the extremely pure base metal from highly contaminated secondary material.

Jan 1, 1961

By H. Stuart Auvil

Twelve samples of run-of-oven coke were taken at coke plants in the United States and Canada. Sampling procedure was directed toward obtaining the highest possible degree of uniformity in the gross samples, so that variations in results caused by sampling variations were at a practical minimum. Under these conditions the standard deviation of the screen analysis test on 500-pound samples is found to range from 1.2 percent for the 1-inch screen to 4.5 percent for the 5-inch screen. At present, the A.S.T.H. standard method of test requires that results be reported to the nearest 0.1 percent. This implies a higher than actual degree of precision, and revision of the report required by the method is suggested. Much larger Samples than are generally tested are required to reduce normal testing errors to a point where they are not appreciable fractions of the total variations found in a smoothly operating plant. For example, it is deduced that over 100,000 pounds of coke must be screened to determine if ordinary day-to-day variations in screen analysis have appreciable effects on the performance of a blast furnace.

Jan 1, 1950

By Martin J. Gavin

During the recent study of lubricating oils carried on in the San Francisco laboratory of the United States Bureau of Mines, it became desirable to distill the oils used in the experimental work at pressures as low as 10 millimeters (mercury column) absolute. In the effort to Overcome difficulties and eliminate sources of error, certain changes were made in the apparatus for vacuum distillation used by the Bureau of Mines for crude petroleum.4 These changes were described in R.I. 2819, issued in July, 1927. Subsequent to the publication of R.I. 2819 several other changes have been made, and the present form of the apparatus for vacuum distillation of lubricating oils is described in this revision of R.I. 2819. These changes were found to give more accurate checks on duplicate distillations. The major part of the credit for the laboratory work which developed the changes in the apparatus and method revised herein is due to Boyd Guthrie, assistant petroleum chemist, and R. V. Higgins, junior chemist, o the San Francisco laboratory, United States Bureau of Mines. DESCRIPTION OF APPARATUS The distilling flask employed is essentially the Hempel flask as used by the United States Bureau of Mines for the analytical distillation of petroleum.5 he complete apparatus is shown in Figure 1. The fractionating column and exposed portion of the flask is wrapped with 4 inch asbestos rope and then surrounded by a cylindrical hood of 1/8 inch pliable asbestos sheet with a narrow air space between the wrapping and the cylindrical hood. This was found necessary to prevent any radiation or convection heat losses from the column, and resulted in obtaining a more even and constant fractionation by eliminating any dephlegmating action caused by temperature changes around the column.

Jan 1, 1930

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

A new personal respirable dust monitor developed by Rupprecht & Patashnick Co., Inc. in a multi-year project funded by the National Institute for Occupational Safety and Health (NIOSH) generated promising results in underground coal mine testing performed by NIOSH and industry representatives during the summer of 2003. The mine data showed that the personal dust monitor (PDM) performed similarly to co-located manual reference samplers for full-shift samples at all four underground coal mines at which the evaluation took place. The technology that forms the heart of the PDM, called the tapered element oscillating microbalance (TEOM system), is unique in its ability to collect suspended particles on a filter while simultaneously determining the accumulated mass with National Institute of Standards and Technology traceability. Because the monitor measures the true particle mass collected on its filter, its results do not exhibit the same sensitivity to water spray as do optically based measurement approaches. The technique achieves microgram-level mass resolution even in the hostile mine environment, and reports dust loading data on a continuous basis. Using the device, miners and mine operators have the ability to view both the cumulative and projected end-of-shift mass concentration values, as well as a short-term 15- or 30-minute running average. During underground mine trials in the summer of 2003, technical personnel used the readings from the PDM to identify and correct several abnormal dust generating scenarios. These events demonstrated the potential of the PDM to be used as an engineering tool to evaluate the effectiveness of various dust control strategies. In a separate evaluation performed by CONSOL Energy, Inc., the mine operator evaluated the benefit of a proposed new water spray-based dust control system. Engineers measured the dust concentration upstream and downstream of a production location under different dust control scenarios using two PDM units. By evaluating the change in the dust loading between the upstream and downstream monitoring sites, the company was able to determine in a few hours which hardware configuration would yield the greatest benefit to the workplace environment. BACKGROUND Measuring underground coal mine dust concentrations is an essential part of protecting miners&apos; health. The U.S. Secretary of Labor and the Federal Advisory Committee on the Elimination of Pneumoconiosis among Coal Mine Workers has recommended that better monitoring of coal miner dust exposures be used as a method to improve miner health. In consultation with labor, industry, and government, NIOSH issued a contract to Rupprecht & Patashnick Co., Inc. (R&P), Albany, N.Y., to develop a one-piece PDM. The object was to miniaturize TEOM technology into a form suitable for a person-wearable monitor that would enable accurate end-of-shift dust exposure information to be available to miners. Furthermore, any person-wearable dust monitor should minimize the burden to the wearer by incorporating the monitor into the mine worker&apos;s cap lamp battery, with exposure data continually displayed during the shift to enable workers and management to react to changes in dust exposure. In the summer of 2003, NIOSH conducted extensive testing of the PDM to determine its laboratory and in mine performance. In addition, anecdotal information collected in the mines showed several occasions where miners were able to identify situations that produced high levels of respirable coal mine dust The PDM&apos;s response to unplanned changes resulted in action being taken to keep dust exposures as low as possible. In another case that demonstrated the PDM&apos;s versatility, a mine was seeking to find a better dust control solution on its longwall headgate stageloader. In this instance, the PDM was used as a diagnostic tool by the miners to quickly evaluate the control technology. [ ] HOW DOES THE PDM WORK? The PDM is configured to provide accurate respirable dust personal exposure information in a form that is as convenient to wear as a normal cap lamp (See Figure 1). Respirable dust exposure data displayed by the device has two main objectives: providing the miner and mine operator with timely values to avoid overexposure to dust, allowing them to make any necessary changes during the course of a work shift; and computing an accurate end-of-shift statistic for a miner&apos;s average respirable dust exposure. The mass sensor embedded in the PDM, holds the key to the accurate, time-resolved dust concentration measurements. The inertial, gravimetric-equivalent, mass measurement technique used in the device typically provides a limit of detection on par with that of the most sensitive laboratory-based microbalances.

By Frank E. Chase, Deno M. Pappas, Christopher Mark

Multiple seam interactions are a major ground control hazard in many U.S. underground coal mines. The two most common types are: • Undermining, where stress concentrations caused by previous full extraction in an overlying seam is the primary concern, and; • Overmining, where previous full extraction in an underlying seam can result in stress concentrations and rock damage from subsidence. The National Institute for Occupational Safety and Health (NIOSH) has completed a major study aimed at helping to identify the location and likely severity of these interactions. In the course of field visits to mines throughout the U.S., more than 300 multiple seam case histories were assembled into the largest data base of multiple seam case histories ever collected. These data were analyzed with the multivariate statistical technique of logistic regression. The study also employed LaM2D to estimate the multiple seam stresses, ALPS and ARMPS to determine pillar stability factors, and the CMRR to measure roof quality. The study resulted in the development of a computer program, called Analysis of Multiple Seam Stability (AMSS), which can help mine planners to evaluate each potential interaction and take steps to reduce the risk of ground control failure. AMSS first evaluates pillar design by calculating the single seam Stability Factor (SFSS) using ALPS or ARMPS. It also automatically generates a LaM2D analysis that provides the additional multiple seam stress so that the final, multiple seam SFMS can be determined. The second part of the AMSS procedure builds upon the statistical findings that overmining is much more difficult than undermining, isolated remnant pillars cause more problems than gob-solid boundaries, and weaker roof significantly increases the risk of multiple seam interactions. AMSS quantifies these effects and predicts the outcome in terms of three levels of risk: GREEN (where a major multiple seam interaction is considered unlikely), YELLOW (where adding a pattern of cable bolts or other equivalent supplemental support could greatly reduce the probability of a major interaction.), or RED (a major interaction should be considered likely, and it may be desirable to avoid the area entirely).