Search Documents

By G. R. Fitterer, C. H. Herty

"INTRODUCTION Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis in easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot—top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel.For a large tonnage of steels which go into articles manufactured by deep—drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low—carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, — that is to say, deoxidized with manganese and perhaps a small amount of aluminum, — the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper—central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low—carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel. These defects would be minimized by clean killed steel."

Feb 1, 1931

[In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 17 and 23, outlining the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of publications recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 17 and condition 2 on page 23. An explosive or a blasting device enumerated in the permissible lists of thin Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.]

Jan 1, 1941

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 17 and 23, outlining the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of publications recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 17 and condition 2 on page 23. An explosive or y blasting device enumerated in the permissible Lists of thin Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1941

By Oliver Bowles

The mineral asbestos, because of its unique fibrous character, is allied to cotton and wool but has the advantage of heat and fire resistance; therefore, it supplies many industrial needs for which no substitutes are yet available. This report covers the essential features of the asbestos industry, including occurrence, production, mining, milling, utilization, international trade, and marketing. The United States leads all countries in the manufacture of asbestos products, but domestic sources furnish only a small fraction of the raw material required. As the United States is dependent to so great an extent on foreign supplies of raw materials, the bulletin deals at length with the asbestos industry in foreign lands. Several reports now available deal with the industry in individual countries. Among them are Chrysotile Asbestos in Canada, by J. G. Ross; Asbestos in the Union of South Africa, by A. L. Hall; and a series of articles on the Russian industry, by Walter A. Ru Keyser. These have been drawn upon freely, and full acknowledgment is hereby made for the helpful information thus secured. The file of the magazine Asbestos also has furnished many valuable data touching all phases of the industry. Many other books and articles listed in the bibliography at the end of this bulletin have been utilized and have been supplemented by the author's intimate acquaintance with the industry for about 20 years. The intent is to present a concise, world-wide, historical, technical, and economic treatment of the asbestos industry.

Jan 1, 1937

By S. J. Gasior

A method for destroying the caking properties of bituminous coal was developed by the Bureau of Mines. Coal is treated in a fixed bed by heating through its plastic range under controlled temperatures in mildly oxidative atmospheres composed of inert gas and/or steam containing about 1 volume-percent oxygen. High-volatile A (hvab) and high-volatile B (hvbb) and low-volatile bituminous (lvb) coals in the size range 1/8 to 1-1/2 inches were successfully treated at 0 (atmospheric pressure) to 300 psig in static beds 6 to 18 inches deep. Conditions of treatment depended on the coal and ranged from 80 to 200 minutes at 350° to 510° C. Char produced in this manner from hvab coal was gasified with steam at 800° C and 100 psig in a fixed bed in one series of tests and in other tests was exposed to hydrogen in a dilute co current free-falling-bed system at 750° C and 3,000 psig without agglomerating.

Jan 1, 1965

By Allen D. Look

Underground fires often prove difficult to control , and a small fire can quickly grow into a large one , endangering life and causing large property damage . Even a small underground fire may produce enough noxious gases to cause suffocation ; therefore , every precaution should be taken to prevent and control such fires . It is ironic that mine fires should be caused when utilizing materials that are in themselves fire - resistant ; yet , cutting and welding of iron and steel are proving to be common causes of underground fires in metal mines . This paper includes 19 examples of underground fires of this nature , and undoubtedly this is only a fraction of the number of similar fires that have occurred in the last few years . This paper will review some metal - mine fires caused by cutting or welding and point out precautions to be taken to prevent other fires from this cause .

Apr 1, 1948

By James J. Olson

Previous Bureau of Mines studies of vibrations from quarry blasts have shown that the square root of the charge-weight may be used to group particle velocity data from various charge sizes, and that empirical propagation equations may be used to estimate vibration amplitudes. Particle accelerations of the sandstone roof of the White Pine Copper mine, Michigan, were measured to determine whether similar propagation equations may be developed for underground mine blasts. Vibration data from White Pine blasts were best grouped by scaling with the square root of the charge weight. Cube root scaling did not effectively group the data. The empirical propagation equation AW1/2 = 50,000 (R/W1/2)-2.21 where A is peak-to-peak acceleration in g's, W is the zero-delay charge-weight in pounds, and R is the distance from the blast in feet, may be used to estimate maximum vibration amplitudes from production sized blasts. Vibration differences among headings and types of explosive charge (AN-FO and dynamite), while statistically significant, were not a major factor in the estimation of maximum vibration amplitudes with an empirical propagation equation. Vibration differences between types of explosive charge were larger than the differences among headings, indicating that some reduction of vibration amplitude might be gained by using AN-FO rather than dynamite. Acceleration records from both White Pine's AN-FO and dynamite production blasts show that high intensity vibrations from the delayed portions of the blast (each delay interval = 25 milliseconds) were separate events, and that the zero-delay portion of the blast produced the maximum vibration amplitudes. If the pull of the underground blast round can be maintained, a reduction of the zero-delay charge-weight may effectively reduce the maximum vibration amplitude of the blast.

Jan 1, 1970

By F. S. Crawford

It has been said that safety promotion passes through four stages--the band-playing, the machine-guarding, the protective equipment, and finally the educational stage; the last is the most important in the development of the safety program. It has been estimated that only 15 percent of accidents can be pre- vented by machine guarding and protective equipment; the other 85 percent must be stopped by the safety efforts of the individual workers and their supervisory officials, and one of the fundamentals of safety work is the education of workers to develop safety consciousness or safety mindedness. One way of educating men to think about safety is by the use of posters. Safety engineers at the Calumet 2 Hecla mines in Michigan have been conduct- ing a safety contest among the men by the use of posters of an unusual type in addition to those usually employed to illustrate bad practices and to display the number of days without a lost-time accident. The first requisite for the success of the safety poster is a good artist or draftsman; in the poster contest instituted at the Calumet & Hecla mines two sheets were prepared illustrating various conditions in the slope workings, including a large number of unsafe practices. The object of the contest was to get the men to think about safety through criticism of the unsafe conditions displayed on the posters. The following notice accom- panied the posters:

Feb 1, 1935

By John Gross

In connection with some investigations being made at '!'he Ra.re uid Precious 1ets.ls Station of the U, S. Bu.rea.u of Mines, at Reno, Nev., on the precipitation of gol'i and silver from cyanide solutions, it wa.s sug­ gested tnat the use of acetylene for this purpose be investigated, A pa.tent was iss·.ied to Fre<!.erick W. Martin and Frederick Stl1.bbs in 1900 covering the precipitation of precious metals from cyanide solu­tions by acetylene, The acetylene used in the tests described below wa3 made f'rom a. corr.:nercial cal ci \'!Z:l carbid.e, A r..umber of exper:me11. +,s rezul ted in more or lP.ss ccmplete pree;p1tatien of silver, -but 1n no case was a11Y gold precipitated. As silver acetylide, obtained by precipitatir.g the silver from an ar:::ncni'i\.Ca.l so1ut1on of silver n,. tra.te by acetylene, is yellowish white, esn:, solu'.)le in cyanide and hlghly explosive, and the pr9cip1tate ob­tain£ frcvm the cy'31lide sclutions was black, not tlubla L., cyanide and not explooive, it 'Na.s deid-,d. to ir.·.restigate the na.tur.e of the slJ.ver pre­cipit.te !rem the cy;r:iide solu·t:i.i,ns, !n prepa;.•i::lg a lge (!\,wrttity ,:f the preci-pi tte 1 t. wa, fo·und that a.fter c,:.\i;:1 ete prEc"'.pi tat ion cf the eil ver the !IOl ution con ta.ined soluble eulphic.e • Thia p:!:'O'lided a el f!W "lt·d. a.ft er apr,ropri-9.te tests the preeipita.te VIO,I proved to 'be ailver sulphide.

Apr 1, 1922

By Lloyd A. Morley, Robert Stefanko

1. Anonymous (Berggewerkshaftliche Versuchsstrecke), "75 Jahre Berggewerkshaftliche Versuchsstrecke, 1894-1969," 1969. 2. Anonymous, British Symposium on Flameproofing and Intrinsic Safety, IEEE Conf. Report Series No. 3, 1962. 3. Anonymous (Ministry of Fuel and Power), "A Review of Electrical Research and Testing with Regard to Flame-Proof Enclosure and Intrinsic Safety of Electrical Apparatus and Circuits," 1943. 4. Australian Standard Specification, ASC-98, "Electrical Equipment for Explosive Atmospheres," 1970. 5. Belgium Standard Specification, Norme NBM 286, "concernant la protection par enveloppe antideflagrante," 1965. 6. Bossert, J.A., "Approval for Electrical Equipment for Hazard Locations," paper PCI 66-33, IEEE 16th Annual Petrol. and Chem. Ind. Conf., L. A., California, Sept. 15-17, 1969. 7. Bossert, J.A., "Intrinsic Safety in Canada," Electrical Safety Practices, ISA Monogram, vn. 112, 1969. ,8. British Standards, BS229, "Flameproof Enclosure of Electrical Apparatus," 1957. 9. British Standards, BS4683 Part 1, "Classification of Maximum Surface Temperatures," 1971. 10. British Standards, BS4683 Part 2, "The Construction and Testing of Flameproof Enclosures of Electrical Apparatus," 1971. 11. Brown, G.R., and Silver, S., "An Explosion Hazard Due to Inflam¬mation of Aluminum Particles in Flat Flanges of Flameproof Enclosures," CEAL No. 197, Canadian Explosive Atmospheres Labor¬atory, 1969. 12. Campbell, J.D., and Chudleigh, J.P., "Problems Encountered in Designing Electrical Systems for Hazardous Areas," paper PCI-69¬31, IEEE 16th Annual Petrol. and Chem. Ind. Conf., L. A., California, Sept. 15-17, 1969. 13. Canadian Standards Association, C22.2 No. 30, "Explosion-Proof Enclosures for Use in Class I Hazardous Locations." 14. Dainty, E.D., and Brown, G.R., "Explosion Gas Temperatures at the Entrance to Flanges of Enclosures Containing 8.5% Methane-Air Mixtures," CEAL No. 196, 1969.

Jan 1, 1974

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Air Moving and Conditioning Association, Fan Application Manual Part 1, Fans and Systems, AMCA Publication 201, 1976a. Air Moving and Conditioning Association, Fan Application Manual Part 2, Troubleshooting, AMCA Publication 202, 1976b. Air Moving and Conditioning Association, Fan Application Manual Part 3, Field Performance Measurements, AMCA Publication 203, 1976c. Air Moving and Conditioning Association, Directory of Products Licensed to Bear the AMCA Certified Ratings Seal, Edition 27, August 1, 1975. Allan, A. L., Hollwey, J. R., and Maynes, J. H. B., Practical Field Surveying and Computations, American Elsevier Publishing Co., Inc., New York, 1968. American Society of Heating Refrigeration and Air Conditioning Engineers Std. 51-75, Air Moving and Conditioning Association Standard 210¬74, Laboratory Methods of Testing Fans for Rating. Anderson, T. C., and Nugent, J. W., "Mine Ventilation Pressure Differentials with a Programmable Hand Calculator," MESA Informational Report 1050, 1977. Atkinson, J. J., "On the Theory of the Ventilation of Mines," Trans. N. E. Inst., Vol. 3, 1854, pp. 118. Barnes, E. L. S., "Mine Ventilation Network Analysis," International Mine Ventilation Congress, Marshalltown, S. Africa, Sept., 1975. Boshkov, S, and Amontree, B., "How Operator Proximity Affects Anemometer Readings," Coal Age, Vol. 55, No. 5, 1950, pp. 85-56. Boshkov, S., and Wane, M. T., "Errors in Underground Air Measurements," Mining Engineering, Vol. 11, No. 7, November, 1955, pp. 1047-1053. Briggs, H., "The Underground Leakage of Air, Investigation of the Porosity Coefficient," Transaction of the Institution of Mining Engineers, Vol. 82, pp. 111-121. Brown, J. R., and Hinsley, F. B., "The Flow of Air in Bends and Straight Airways," Transaction of the Institution of Mining Engineers, Vol. 116, July, 1957, pp. 845-867. Burrows, J., "Measurement of Fan Pressures," Journal of the Mine Ventila¬tion Society of South Africa, Volume 27, No. 4, April 1974, pp. 57-63.

Jan 1, 1977

By R. G. Knickerbocker

[The Electrornetal~.1~~1c~.l T,:tt31~tn~ir of the Bureau of Miner,, 3oulder City, !.Tev. , invsst:&apos;.~:es 1:h .-inc.z-.l ci.c;,oritr, in 51-3 regon around Boulder Dam, i~d. this papei- ?i*esmt; tvr) cl-c~;ef.o!~~ilcinl;$ of n s5siqn of atufiies on boron ninerala GB~O 3;; tlir t ~t;s?,Lo:]

Jan 1, 1940

By J. W. Paul

Withdrawing timber in coal mines is done for the purpose of inducing the roof to cave in the mined-out areas and thereby relieve stresses in the immediate roof material over the working places adjacent to the breakline of the roof, thus preventing the crushing of the ends of pillars and adding to the safety of those engaged in pillar extraction. A secondary purpose is the recovery of timber for further use either as prop-, crossbars, lagging, sprags or cap pieces. At some mines timber is withdrawn as a precaution against fire which may he of spontaneous origin, because wood always aids a fire of any origin. With some of the power-driven types of machines now in use a greater proportion of mine timber may be recovered, and in mines where pillars are left too narrow for their removal some of the timber in rooms might be salvaged for further use.

Jan 1, 1933

By Rees D. Groves

The Bureau of Mines conducted research on reactions of copper sulfide minerals with chlorine in an aqueous system. Selected samples of covellite, chalcopyrite, chalcocite, bornite, and pyrite were leached with aqueous chlorine solutions. The mineral samples were sized on to minus 100- plus 325-mesh, individually mixed with precleaned sand and leached in an enclosed percolation column. Each mineral was leached in stages to achieve about 90 percent mineral dissolution. The chlorine leaching solutions were produced by reacting sodium hypochlorite with hydrochloric acid within the closed system. The study showed that when the mineral dissolution was complete, the reaction products (copper, iron, and sulfur) were in their highest oxidation states and a stoichiometric amount of chlorine was consumed. Although elemental sulfur formed as an intermediate product, it was oxidized to sulfate during the leach.

Jan 1, 1973

By Wm. O. Vanderburg

This paper describing the mining practices at the Block P mine of the St. Joseph Lead Co. at Hughesville, Mont., is ore of a series of similar papers being prepared by the Bureau of Mines on mining practices, methods, and costs in the various miner of the United States. ACKNOWLEDGMENTS In the preparation of this paper the writer acknowledges the assistance of R. H. Willcomb, general manager, William Thorson, mine superintendent, and B. P. Bellport, mining engineer, of the Hughesville division of the St. Joseph Lead Co.; and of E. D. Gardner; supervising engineer, U. S. Bureau of Mines, Southwest Experiment Station, Tucson, Ariz.

Jan 1, 1931

Prevention of coal-mine explosions depends largely upon thorough knowledge of the causes that initiate explosions. A review of coal-mine explosions in one geographical area when supplemented by nationwide data of similar nature, should serve as a guide for the adoption of measures for explosion prevention. Explosions in bituminous-coal mines of the United States during the 10 years ended December 31, 1932, ranked third in the causes of fatal accidents and constituted 16.1 percent of all fatal accidents in bituminous mines. Kentucky now ranks fourth in coal output in the coal-producing States of this country; a study of the coal-mine explosions in this state will be of definite interest locally among coal-mining people, as well as to those in the coal-mining industry who are concerned in preventing coal-mine explosions. This circular reviews gas and dust explosions in Kentucky coal mines to show their hazards, to point out the influence of certain factors in causing explosions, and to indicate the effectiveness of preventive measures.

Jan 1, 1934

By Harry Perry, Mary S. Esfandiary

This is a revision of a directory of coal research organizations throughout the world that was first published in 1961 as Bureau of Mines Information Circular 8008. Because of the wide acceptance of the first edition , a revision which would supply up- to - date information on coal research and which would facilitate communication among organizations of similar interest seemed important . This compilation includes the names and activities of organizations of various types -government , university , private , and industry . The areas of investigation that each organization is engaged in are indicated in broad terms : Analysis and constitution , mining and geology , preparation , briquetting , combustion , high- and low-temperature carbonization , gasification , conversion to solid and liquid fuels , and health and safety . Publications issued by and describing the work of each organization are cited ; almost all of the organizations also publish results of their investigations in the technical press . Selected technical and trade publications that publish information on the science and technology of coal and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country . Information that would improve coverage and accuracy of the next revision of the publication will be welcomed by the Bureau of Mines .

Jan 1, 1966

By Jeffrey Shawn Peterson

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. In response, the National Institute for Occupational Safety and Health (NIOSH) conducts research to reduce the noise emission of various underground coal mining equipment, an example of which is a roof bolting machine (RBM). After the removal of coal or rock, the remaining strata may be subject to fall, either from overhead (the roof) or from the side (the rib). One method used in underground coal-mines to prevent failures requires the installation of roof bolts. The roof bolting machine operator trams the machine to the required location, drills a hole into the strata, and then installs a roof bolt, supporting the roof or the rib, as the case may be. Field studies support the premise that, on average, drilling noise is the loudest noise that a roof bolting machine operator would be exposed to and contributes significantly to the operators? noise exposure. NIOSH has determined that the drill steel radiates a significant amount of noise during drilling. NIOSH is developing bit and chuck isolators to reduce vibration, and thus noise radiation of the drill steel, with the longer-term goal of reducing roof bolting machine operator noise exposure. Laboratory testing has shown that operator ear sound pressure levels may be reduced by 3 to 7 dB(A), depending upon the test configuration and drilling media.

Jan 1, 2009

By BUREAU OF MINES

A complete list of permissible mining equipment, rescue apparatus and gas masks tested prior to July 1, 1928, was published in Bureau of Mines Information Circular 60772. The present list includes practically all equipment tested and, approved by the Bureau, up to and including Jan. 1, 1929. It covers electric air compressors, coal drills, mining machines, loading machines, conveyors, mine pumps, room hoists, mine telephones, rock-dusting machines, switches, electric cap lamps, flame safety lamps, electric hand and trip lamps, flash lamps, methane indicators and detectors, blasting units, storage barrery locomotives, tandem locomotives, power trucks, concrete mixers, self-contained oxygen breathing apparatus and gas masks. The system under which those devices were tested permits the manufacturer, after his equipment has passed certain tests prescribed by the Bureau of Mines, to mark his equipment with a seal shoring that it has been "approved" by the Bureau. These tests are designed to insure that the equipment has the minimum requirements for safety in use. The only object of the Bureau in making such tests and pub- lishing lists of permissible equirment is to safeguard the lives of workers and to help lesson the hazards of mining.

Jan 1, 1929

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume- percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966