Search Documents

By R. E. Lindstrom

Separation efficiency of a 4 percent divinylbenzene (DVB) resin is not altered over a wide range in temperature. A 12 percent DVB resin, however, exhibits a marked sensitivity to temperature. When flow rates are high at ordinary temperatures, 4 percent DVB resin exhibits higher efficiency, but at 200° F. both resins are equal in performance. Effective separation of rare-earth mixtures may be obtained with hydrogen as a retaining ion by maintaining column temperatures above the solubility of ethylenediaminetetraacetic acid (EDTA) in the free acid form. Slightly lower separation characteristics were obtained with this method as compared with copper as a retaining ion, Recovery of 99 percent of the EDTA from spent eluting solutions that contain copper has been accomplished by a calcium-copper displacement reaction followed by EDTA precipitation. Impurities in the product are correspondingly low. Recoveries of EDTA from holmium solutions with sulfuric acid are substantial; however, those from yttrium solutions are quite modest. Radiotracer experiments show the presence of approximately 0.1 percent yttrium contamina¬tion in the recovered material. The study presented is one phase of a broad research program designed to assist the technology of separating and purifying rare-earth elements.

Jan 1, 1961

By J. A. Rowland

Manganese-copper alloys containing 60 percent or more electrolytic manganese exhibit an unusual combination of high vibration damping capacity with good strength properties. Properties of the pure alloys were first studied in the laboratories of the Federal Bureau of Mines and have been described in a series of technical papers1/ published from 1941-49. The unusual characteristics of these manganese-copper alloys attracted the attention of research metallurgists and several additional investigations have also been reported in the literature.2/ The engineer, also, was attracted by the combination of high strength and high vibrational damping capacity possessed by these alloys. A wide field of application in structural and machine design was obvious. However, serious difficulties encountered in commercial fabrication of structural or machine components from the alloys retarded attempts at their practical utilization. For this reason the Federal Bureau of Mines, in cooperation with the United States Navy, Bureau of Ships, undertook a program designed to develop practical methods for fabricating a selected group of the high-damping alloys. It is the purpose of this paper to summarize a part of that investigation in a form suitable for use by the metallurgist interested in commercial fabrication of the alloys.

Jan 1, 1955

By V. A. Marple, K. L. Rubow, B. A. Olson

"A virtual impactor personal aerosol sampler (VIPAS) bas been developed for use in diesel-equipped mines to collect size-separated samples or diesel exhaust and mine dust particles in the respirable size range. This sampler consists or three stages: a 10-mm cyclone, a 0.8- µm cutpoint virtual impactor and two filter cassettes. The large non-respirable particles are removed in a 10-mm cyclone. The respirable particles from the cyclone pass through a 0.8- µm cutpoint virtual impactor with the particles larger than and smaller than 0.8 JI.ID (mine dust and diesel exhaust particles, respectively) collected on two 37-mm filter cassettes. The sampling How rate is 2 L/min so as to be compatible with the standard respirable dust sampler and personal sampling pumps. INTRODUCTIONThe mining industry has been increasing its use of diesel-powered equipment in underground mines, especially in coal mines. With this increased usage has come an increased concern regarding the health effects associated with inhaling diesel exhaust particles since they are in the respirable particulate size range. A Mine Safety and Health Administration (MSHA) advisory committee directed MSHA to develop a sampling protocol for diesel exhaust particles to assess worker exposure (MSHA, 1988). In addition, the National Institute for Occupational Safety and Health (NIOSH) has recommended that ""whole diesel exhaust be regarded as a potential occupational carcinogen as defined in the Cancer Policy of Occupational Safety and Health Administration"" (NIOSH, 1988).Past work, with cascade impactors in both the laboratory and in underground coal mine studies, has shown that the diesel exhaust particles are primarily in the less than 0.8 µm aerodynamic diameter size range whereas the coal dust particles are primarily greater than 0.8 µm (Marple et al., 1986; Cantrell, 1987; Rubow and Marple, 1988; Rubow et al., 1990a, b; Cantrell and Rubow, 1991). This work has been jointly performed by the University of Minnesota and Bureau of Mines researchers over the last 8 years. Typical particle size distributions for a diesel-equipped coal mine and an all electric coal mine are shown in Figure l. Note that the particles in the < 0.8-µ.m mode are the diesel exhaust particles (seen only in diesel-powered mines) and the particles in the > 0.8-µ.m mode are coal particles (seen in both the electric-powered and diesel-powered coal mines). Chemical mass balance analysis was also performed on these two size fractions to determine the degree of particle cross-contamination in the two modes. This analysis showed less than 10% cross-contamination, i.e., in coal mines Jess than 10% of the diesel exhaust particulate was collected in the coarse fraction and Jess than 10% of the mine dust was collected in the fine fraction (Cantrell, 1987; Rubow et al., 1990a)."

Dec 1, 1996

By Foster Fraas

The dielectric constant .has been frequently referred to as an important property in electrostatic separation whore the particles are in an air ambient. Hatfield (1) has studied the problem on the basis of fundamental theory, with the conclusion that separations in air dependent on the differences in dielectric constant, in conjunction with a nonhomogeneous field, are not feasible, because of the low dielectric strength of the air. Although Hatfield has made the statement without showing the calculation or data, calculated values substantiating this under certain conditions of the problem will be given in the following text. However, under other Conditions, these conclusions do not hold, and it is probable that the dielectric constant is indirectly influential.

Jan 1, 1948

By Michael J. Magyar

This report contains a cost estimate of the Bureau of Mines process for dewatering Alaskan placer effluent streams with polyethylene oxide (PEO). In this process effluent slurry is withdrawn from the placer plant pond system after a primary settling stage. A dilute PEO solution is injected into the slurry line to flocculate the fine, suspended solids. The flocculated solids are dewatered on a stationary screen. Clarified water is returned to the placer operation or discharged, while the 35 percent solids waste is pumped back into the mine cut. Cost estimates are presented for dewatering plants processing 1,000 gallons per minute of effluent slurry at three representative turbidity levels. Both the placer and the dewatering plants operate on the same 1-shift-per-day, 6-day-per-week schedule for the 100-day Alaskan operating season. Estimated fixed capital costs for these plants processing placer with effluent turbidities of 1,000, 3,000, and 5,000 nephelometric turbidity units (NTU) are approximately $29,000, $31,000, and $34,000, respectively, on a fourth quarter 1986 basis. Operating costs are estimated to be $0.34, $0.37, and $0.40 per thousand gallons of effluent slurry.

Jan 1, 1987

By Lloyd A. Morley

A concept is presented to improve underground coal mine electrical system safety and availability. This proposed technique is based upon the ability to predict incipient failures in the mine power system. Prediction is made possible by a new method, developed during this research, which uses a minicomputer to implement pattern recognition algorithms. The theoretical basis of the prediction system is discussed, along with synthesis of the hardware and software sections. The deterioration modes which could be detected are examined, and an evaluation of the system&apos;s ability to predict incipient failure is presented. Typical results of the system&apos;s performance during laboratory simulation of power system deterioration are given.

Jan 1, 1977

By John Durkin

Owing to the daily exposures of uranium mining personnel to 222Rn daughters, a device is needed that will continually monitor individual exposure. Such a device has been built and tested by the Bureau of Mines and is known as a radon daughter dosimeter. This is an electronic instrument using a solid-state detector and circuitry. The concept of the instrument, which is a personal device worn throughout the working shift, is to evaluate an individual&apos;s cumulative exposure to airborne radon progeny, expressed in units of working level hours. Since the instrument is in close proximity to the miner and measures continual exposure, it avoids the errors caused by the present technique of spot checking of the environment and provides a more accurate account of total cumulative exposure.

Jan 1, 1977

By Clyde E. Williams

The Northwest experiment station of the Federal Bureau of Mines , at Seattle , Wash . , was established in December , 1916 , and is one of 13 mining experiment stations maintained by Act of Congress , under the direction of the bureau , in the various sections of the country . Under the terms of the organic Act (March 3 , 1915 ) , the province and duty of these experiment stations is to cake investigations and disseminate information with a view to decreasing waste and improving the efficiency in the production , treatment , and utilization of mineral substances . The investigations carried on at the Northwest experiment station attempt to cover the needs of the mineral industry of the States of the Pacific Northwest and of the coastal regions of Alaska . The most in ortant needs of this district are for work on coal washing , electrometallurgy , and ceramics . The electrometallurgical investigations are not necessarily limited to the Problems of the Northwest , but may be of general application . Problems other than those specified above are referred to other stations of the Bureau that specialize on the particular type of investigation required . The Northwest station closely cooperates with the State of Washington through the University of Washington and with the State of Oregon through the Oregon Bureau of Mines and Geology . The University of Washington at Seattle has donated the use of an entire building , which houses the station's administrative offices and chemical laboratory , and parts of two other buildings which are usea in conducting the experimental avestigations . Twenty-five thousand dollars is expended annually by the Federal Government , while the State of Washington each biennium appropriates $ 20,000 , and the State of Oregon from time to time appropriates various amounts for the conduct of work along cooperative lines . Also , the station cooperates with private organizations tht have problems similar to those in which the station is interested . For example , the Washington Electrochemical Co. is cooperating in the electrometallurgical research, and furnishes part of the supplies and technical assistance required .

Mar 1, 1922

By J. F. Barkley

During the present war emergency, under the urge of the Federal Government to store coal, the following questions are frequently asked by coal users: (a) Will the coal lose any, of its heating value in storage? (b) Will it slack and give a smaller-size coal? (c) Will its burning characteristics change in any way? (d) Will it catch fire from spontaneous combustion? (e) What precautions should be taken when coal is stored? DISCUSSION (a) Loss of Heating Value Studies by the Bureau of Mines show that the loss of heating value of coal in storage commonly has been overestimated. Various types of storage tests were made on New River, Pocahontas, Pittsburgh gas, and Sheridan (Wyo.) coals. The following is quoted from Bureau of Mines Bulletin 136, Deterioration in the Heating Value of Coal During Storage, by H. C. Porter and F. K. Ovitz (p. 8):

Jan 1, 1943

By Frank L. Gaddy

In this report, a description of mine practices, the preparation of roof bolts for laboratory experiments, the results of tensile-strength determinations, and a discussion of results of these tests are presented. Certain restrictions are recommended for roof bolts subjected to repeated bending, and two methods of complying with these limitations imposed by the restrictions are presented. The practice of bending steel roof bolts for installation in areas where the height of the opening was less than the length of the bolts required to support the immediate roof adequately has been adopted recently in several coal mines in lieu of sectional rods designed for that purpose. In addition, a few of these same mines have been reclaiming the bent rods and reusing them numerous times. The purpose of this study was to determine if these practices decreased the strength of such bolts and thus jeopardized the safety of the men working in these mines.

Jan 1, 1958

By Thomas M. Barczak

he stiffness characteristics of longwall shields were investigated in this Bureau of Mines study. Since longwall strata activity is characterized by roof-to-floor and face-to-waste displacements, a model with two degrees of freedom was used to describe the load-displacement relationship of the shield structure. The model considers the support as an elastic body and relates horizontal and vertical resultant forces acting on the support to associated displacements as a function of the stiffness of the support structure. Stiffness coefficients under full canopy and base contact configurations were determined by controlled displacement loading of longwall shields in the Bureau&apos;s Mine Roof Simulator (MRS). Three two-legged longwall shields of different manufacture were investigated. The stiffness characteristics of these shields were evaluated relative to two parameters, namely, shield height and setting pressure. The test results indicate a reduction in shield stiffness for increasing height. Setting pressure was found to have less of an effect on shield stiffness, producing only a slight increase in stiffness as setting pressure increased. Similar trends were observed for all three shields, indicating a similarity in stiffness characteristics for shields of the same basic configuration.

Jan 1, 1988

By T. A. Klinefelter

"INTRODUCTION During the development work on sponge iron by the Bureau of lines it was desired to produce a product of maximum density for the furnace. One means of doing this would be to make a plastic mixture of the ground ore and extrude as pellets or large slugs or brick shapes.If a pelletizing Process is employed, the pellets must be strong enough to resist breaking when rolled and tumbled in going through the rotary kiln. If a brick-making process is employed, the brick must be strong enough to withstand handling and considerable pressure when stacked in the kilns.The study had two objectives: first, to find a binder of sufficient strength throughout the early stages of curing and heat treating and, second, to determine the degree of curing and heat treatment necessary to prevent disintegration under normal working conditions.Although the investigation had as its primary objective the processing of sponge iron, the data should interest other industries in which non plastic or poor-bonding slimes are a problem."

Jan 1, 1946

By Robert A. Jankowski

Through laboratory and underground studies, the Bureau of Mines has evaluated the use of passive barriers (dust shields) to help confine dust generated by longwall shearers to the face area. Laboratory studies focused first on selection of the optimum barrier design, which proved to be a simple, gobside barrier (made of conveyor belting), coupled with a headgate splitter arm, which was found necessary to prevent the dust cloud from entering the walkway at the headgate end of the shearer when cutting tail to head. Further laboratory testing was done to determine whether using passive barriers in combination with different water-spray dust-reduction methods, including the shearer-clearer system developed by the Bureau, would improve dust reduction over that from using the water sprays alone. It was found that the combination of gobs ide passive barriers plus the full shearer-clearer system was most effective, and surmised that this would be especially useful in thicker seams. However, underground testing revealed that the shearer-clearer system alone was 35 pct more effective in reducing dust contamination than when used with the gobside passive barriers, and far more effective than using passive barriers with a conventional water spray system. For such an effective system as the shearer-clearer; the reduction in avail-able space over the top of the machine actually impeded system performance; this was shom1 in both eastern and western mines. But when used with comparatively inefficient water spray systems, the passive barriers, used in combination with a headgate splitter arm, provide consider-able help in reducing dust levels in the walkway.

Jan 1, 1986

By Philip W. Holland

The U.S. Bureau of Mines has designed and built an inexpensive, weatherproof, temperature-controlled cabinet to provide temporary housing for analytical instrumentation. The cabinet consists of an inverted Styrofoam ice chest, an electric fan for air circulation, and a proportional temperature controller equipped with a thermistor sensor and a light bulb as the heater. The cabinet provides a constant-temperature environment for a moisture analyzer and a strip chart recorder when outside temperatures range from -SO to 21° c.

Jan 1, 1993

By Tony Keller, Setsuo Maeda

Hand-Arm Vibration Syndrome (HAVS) was identified as early as 1918 in Bedford, Indiana in the U.S. Since then much research work has been done around the world in the areas of medical, epidemiological, engineering and legal aspects of HAVS. In Japan, much of the pioneering work in this field has been performed by Dr. Setsuo Maeda and his staff at the National Institute of Industrial Health (NIIH) in Kawasaki. Most recently, reports of work done by this group and by Dr. Ren Dong1 of NIOSH in the U.S., as well as many other suppliers and Japanese practitioners were presented at the 13th Japan Group Meeting on Human Response to Vibration held in Osaka2 during August 3-5, 2005. [ ]

Jan 6, 2006

By J. J. Forbes

The Act of Congress authorizing the establishment of the United States Bureau of Mines became effective July 1, 1910. One of the most important duties Congress delegated to the Bureau in this Act was the study of health and safety conditions in the mineral industries. Early investigations of these conditions revealed the need of prompt Care of injured employees, as, under the difficulties inherent in their occupation, seemingly unimportant wounds if not treated promptly might become infected and cause permanent disability or even death. Many seriously injured persons brought out of mines and plants by fellow workers ignorant of approved methods of giving first aid or of safe means of transportation have been caused suffering and have had injuries accentuated to such a degree as to bring about permanent disability or death. The need of general instruction in first aid thus became apparent. BRIEF HISTORY OF FIRST-AID WORK The education of miners in the United States in first aid probably was conducted systematically first by the anthracite industry in Pennsylvania. Subsequently, first-aid training was carried on actively in Alabama and Indiana. Meanwhile, a general training campaign was carried on among industrial workers by the American Red Cross Society; when the Bureau of Mines began its nation-wide campaign of instructing employees of the mineral industries, the Red Cross turned over that part of its industrial training work to the Bureau but continued to cooperate by furnishing surgeons as judges in important first-aid contests and demonstr tions and assisted for a number of years in determining training methods.

Jan 1, 1937

By R. L. Schmidt

Research conducted over the past 20 years in France, Great Britain, and the United States on the use of the large-hole burn cut has established cer¬tain advantages for this system. Advantages include longer pull and more complete fragmentation from blast rounds. However, research is needed to establish a set of parameters for optimum performance. As part of the Bureau of Mines Advancing Mining Technology for Marginal Resources program, the Twin Cities Mining Research Center, Twin Cities, Minn., acquired a horizontal rotary drill capable of boring holes up to 24 in. in diameter. This was used for a series of underground experiments at White Pine mine, White Pine, Mich., during 1973. Exceptional results were obtained with a 12-1/4-in void hole that yielded up to 18 ft of pull in a 10- by 20-ft drift, Fragmentation was excellent, and the compactness of the muck pile facilitated loading.

Jan 1, 1975

By William C. Cooley

This volume contains copies of the 5 x 8 in. accession card file for all items collected which were judged to be relevant to underground hydraulic coal mining. In many cases, abstracts are included. Abstracts were taken from the source, from other reviews, or from the preliminary screening of Russian documents performed by Dr. A. L. Brichant. No attempt was made to write abstracts for every accession item.

Jan 1, 1975

Until man was able to produce light, his working day was pretty much limited to daylight hours. Underground miners have a special problem because in a mine it is just as dark during daytime as it is at night. The first devices used for mine lighting were torches and open flame 011 lamps. Torches made from twisted grass and dipped in tallow or pine pitch would burn for a while, but they made a lot of smoke and probably went out when they were needed most. During the 15001s, miners lamps consisted of a small metal dish with a hook attached to hang it up. The saucer-shaped dish was filled with animal or fish oil and a wick made of twisted fibers was laid In the 011 and hung over one edge where it would burn. This lamp would burn longer than a torch, but the amount of light cast by the pale, flickering flame was probably only a little better than no light at all.

Jan 1, 1976

By L. B. Pankratz

Enthalpies were determined for synthetic chalcopyrite (CuFeS2) between 298° and 1,050° K and for synthetic bornite (Cu5FeS4) between 298° and 1,100° K by copper-block drop calorimetry. Two transitions were found for each compound. The lower transitions were both crystal transformations from tetragonal (low-temperature form) to cubic (high-temperature form). The chalcopyrite transformation occurred at 830&apos; K with a heat of transformation of 2,405 cal/mole; the bornite transformation was at 485° K with a heat of 1,430 cal/mole. The other transitions were of the second order and were presumed to be magnetic in character. The second-order transitions for chalcopyrite occurred at 930° K, and the one for bornite at 540° K. Enthalpy increments, entropy increments, and heat capacities are tabulated at even temperatures above 298.15° K. Equations of enthalpy are also given.

Jan 1, 1970