Search Documents

By Ivan L. Nichols

Tailings dumps at Mercur, Utah, contain about $7 million worth of gold in 3.5 million tons of mill tailings assaying about 0.07 ounce of gold per ton. Commercial mining and milling at Mercur ceased in 1942. To determine whether improved technology was now available that might permit economic reprocessing of the Mercur dumps, the Bureau of Mines probed for a low-cost method that would be applicable to these tailings. A composite sample prepared for laboratory studies assayed 0.062 ounce gold per ton. About 10 percent of the gold occurred as a water-soluble cyanide. Conventional cyanide leaching dissolved 32 percent of the gold, and hot, strong cyanide solution dissolved 42 percent. Results were not improved by pretreatment with acids, bases, or oxidants. After expensive preroasting, gold recovery by cyanidation was increased to 65 percent. The simple procedures were ineffective, and more effective procedures were too costly for economical processing of Mercur tailings.

Jan 1, 1970

By A. Wahab Khair, S. Jung

"This paper deals with the fracturing process of laterally confined blocks of coal subjected to impact indentation. During the test, blocks of coal with approximate dimensions of 10 in. x 10 in. x 6 in. were laterally confined to predetermined equivalent in-situ stresses and then subjected to an impact indentation by dropping coal cutting bits (various shapes) attached to a known weight from a known height. During the test a number of parameters, namely surface strains (using strain gages), penetration depth (using L.V.D.T.) and acoustic emission characteristics were measured. After the test, the fractured surfaces were photographed with the aid of a camera attached to a microscope. The fracture, its intensity and extended zone within the coal blocks were mapped using sonic techniques. By correlating measured parameters, fractured zones under a given set of test parameters were identified and characterized.INTRODUCTION To improve the understanding of basic failure mechanisms in coal cutting, a better knowledge of fracture and crack regions caused by the indentation in coal is needed. This study reports the detailed experimental procedure used in fracture analysis of indentation experiments on coal specimens using the Acoustic Emission (A.E. hereafter) and sonic techniques. The relationship between microcracking and the inelastic deformation of rock was confirmed by a series of experiments in which the A. E. generated by the cracking in the rock specimen were recorded and the number of events were compared to the strain measurement. (Scholz, 1967).According to fracture mechanism theory, crack initiation in brittle materials such as rocks begins from ""flaws"" either pre-existing or induced by the indentation process itself. Rocks are pervaded by natural cracks and pores, from which numerous possibilities for crack initiation arise (Lindquist, Lai and Alm, 1984)."

Jan 1, 1989

By A. Wahab Khair, Richard D. Begley

"This paper presents results of destructive tests performed on rectangular coal specimen under the influence of two vertical and simultaneous wedge indentation forces. Several wedge designs and spacings were utilized in compression tests. The objective of these experiments was to qualitatively monitor the effect of different wedge designs and spacings on the stress distribution within the coal specimen.Coal samples from the Waynesburg coal seam were cut and trimmed to cubical dimensions of approximately 5 X 10 X 20 cm. These specimen were subjected to parallel compressive forces through two vertically applied wedge indentors. Loading was achieved with a hydraulic hand pump in order to facilitate interferogram construction. The load increments were limited due to the sensitivity of the holographic interferometric technique (holometry) in measuring small displacements; therefore, interferograms were taken only during similar increments in order to allow for a qualitative comparison between different wedge design and spacings. In some cases, interferograms were taken immediately before and after failure of the specimen.Introduction Failure Modes Three distinct modes of failure occur when geologic materials are subjected to wedge indentation forces. As shown in Figure 1, a crushed zone is located immediately adjacent to the indentor while chipping can occur if the fractures initiated in the crushed zone extend upwards to the free surface.. The third failure mode is a zone of intricate frac¬tures located between the crushed zone and the chipping zone. Several experiments have been conducted over the years to better understand crater formation and stress distribution within geologic materials under the influence of an indentor. Generally speaking, crack initiation and propogation observed in these experi¬ments correlate fairly well with wedge indentation theory; however, the nature of the .fractures is greatly influenced by different material properties such as grain size and cleavage planes. In other words, a wide range of behavior has been found in different rocks subjected to wedge penetration. For example, it has been observed that some rocks are merely crushed and indented while others are more prone to cracking and chip formation. Therefore, the development or nondevelopment of chips depends mostly on wedge geometry, rock type and depth of penetration. This work is part of the study associated with opti¬mization of cutting parameters, which is best modeled by using brittle materials and subjecting them to rigid wedge penetration tests."

Jun 1, 1988

By Claude W. Sill

In the course of a series of investigations on vanadium deposits of the western United States, the Bureau of Mines collected many hundreds of samples for chemical analysis. As uranium is often associated with these vanadium minerals, they were also analyzed for uranium, which was pound to be absent in a large percentage of the samples. Since the usual methods for determining uranium are laborious and time-consuming it is very desirable to have some simple qualitative test that can be applied prior to a quantitative analysis to determine whether uranium is present or absent and thus save the time and expense of applying the quantitative analysis to the large proportion of samples containing no uranium. To be acceptable, the test should be specific for cranium, sensitive enough to detect small amounts of uranium, and. simple enough to make it worthwhile to apply. The available methods for detecting uranium lacked one or more of the desired characteristics. Eventually, however, a method was worked out that satisfied all the requirements. This method is probably more specific and sensitive than the usual qualitative methods for uranium, and its simplicity and speed of application make it ideal for testing samples prior to quantitative analysis.

Jan 1, 1945

By A. B. Hooker

Nineteen of the installations were on rental contracts 1.L."'1der whtch the lamps belong to the lamp company and are rented by t.½em to the mine operatj.nt; company. · The other nine installations had been upon an O\Vnership-rental basis, by which the lamps had become the property of the renter at the end of 5 years. Five of t.11e rentec installations were en a special contract calling for a guaranteed light output. These contr2.cts were based upon certified . initial performance, with the provision that the lamps be replaced whenever periodic tests of fully charged lamps, taken at random from t..h.e charge racks, showed a light output of less than 80 percent of the certified performance.

Jan 1, 1942

By G. L. Leumann

"INTRODUCTION AND SUMMARYThe Andover-Sulphur Hill iron mines in Sussex County, N. J., have a production record extending over 100 years. The last production recorded was about 1880. These mines produced high-grade ore of two types: Red ore (hematite) and blue on (magnetite). Some sulfides (lead, zinc, and copper) were found underlying the iron deposits. Data as to size and grade of these sulfide bodies are very sketch"",Howard J. Hewitt of Elizabeth, N. J., lessee of the Sulphur Hill mines from 1940-45, prospected for lead, zinc, and copper. .His only production was several hundred tons of low-grade iron ore, which was crushed and used as heavy aggregate to make concrete blocks for ship ballast.In October and November 1942 made a magnetic survey of this area and bored six-diamond-drill holes with the dual objective of prospecting for sulfides and testing for extensions of the iron-are deposits indicated by the magnetic survey. 2/ In 1944, an iron-mining company examined this property and diamond-drilled seven holes. Between December 1949 and March 1950, the Bureau of Mines in search of sulfide deposits, bored three additional diamond-drill holes. Two of these were on the Sulphur Hill tract and one on the adjoining Tar Hill tract."

Sep 1, 1952

By E. C. Tarpley

The Federal Bureau of Mines has studied solvent extraction as a means of concentrating the mineral components in coal. Solubilities of a number of American coals were determined using abietic acid as a solvent. The effect of rank on solubility was investigated, and maximum solubility was found with coals of intermediate rank. Vitrinite is the most soluble petrographic component; fusinite, micrinitc, and exinite are nearly insoluble. Spore exines also have a low solubility. Abietic acid is a hydrogen donor and reduces pyrite to ferrous sulfide. Mild hydrogenation of high-molecular-weight fragments of the coal structure to those of lower molecular-weight probably contributes to the solvent action. Even where solubility of the coal substance exceeds 90 percent, contamination of the mineral matter with coal makes identification of the mineral components difficult. Further separation might be possible by the application of float and sink techniques to the residue. INTRODUCTION Work n the solvent extraction of coal is conducted to recover commercially useful products and to characterize coal;. and obtain information on their structure. Some coals, particularly those of low rank, contain waxes, resins, and humic acids which can be removed by solvent extraction and find varied industrial uses. In World War II, solvent extraction of coal was conducted on a commercial scale in Germany to obtain a low-ash feed material for hydrogenation and to produce electrodes carbon for the aluminum industry.4 5/

Jan 1, 1960

By Robert W. Freedman

In the Bureau of Mines study, a filter with a 20-by 20-inch-square cross section was inserted into the exhaust ducting of a 4-stroke-cycle, 90-hp diesel engine, and the efficiency of removal of total particulate was measured gravimetrically as a function of time. Removal efficiencies were close to 90 pct during the main portion of several extended runs employing several combinations of filter beds. Variations in engine load had little effect on collection efficiency. Particle size as measured by a Bureau-developed online instrument centered on 0.07 m based on number count. Removal efficiency increased rather sharply for both larger and smaller particles.

Jan 1, 1979

By Raymond B. Ladoo

Deposits of talc are known in many districts in Canada but at the present time active mining operations are reported only in Ontario . Here three companies are now operating, two of which, George H. Gillespie & Co. , Ltd. , and the Anglo- American Talc Co. , are at Madoc . The operations of the former company are probably the largest and best known in Canada . The writer , in his capacity as an engineer of the U. S. Bureau of Mines , was permitted by this company to make an inspection of its mine and mill in June, 1920 , and study the methods employed . This information was desired for comparison with methods employed in the United States . The following description is based on observation made during this visit , supplemented by data supplied by the company .

Sep 1, 1920

By F. M. Boler

The U.S. Bureau of Mines has configured a flexible data acquisition and analysis workstation, which incorporates control and analysis software written in-house for use in mining research experiments conducted in the laboratory and in operating underground mines. This data acquisition system combines computer-automated-measurement-and-control (CAMAC) modular instrumentation with a Unix-based graphics workstation. The data acquisition front-end hardware can be interfaced to almost any computer. CAMAC instrumentation modules adhere to mechanical, electrical, and digital interface standards and can be custom designed or purchased off the shelf. Communications along the CAMAC bus are regulated by the crate-controller module, which contains the only hardware link to the computer interface. Software support for the data acquisition and analysis workstation consists of a series of functions and programs written in the "C" programming language designed to provide flexible and fast data acquisition, processing, and analysis. The user can interactively control the digitizers and other CAMAC modules by sending standard CAMAC read, write, and command function codes from a menu-driven program. Automated data collection is achieved through software that responds to hardware interrupts triggered by acoustic emission or microseismic events. Graphics display routines are used to plot part or all of the data and provide the ability to process and store signal information selectively.

Jan 1, 1990

By M. B. Cooke, A. D. Bauer, E. W. Dean

The Bureau of Mines is collecting and analyzing representative samples of crude petroleum from all the producing fields in the United States , and the results are being published in a series of reports that are preliminary to the issue of a bulletin covering the entire survey . The bureau has recently completed a survey of crude oils from the Kansas district . In all 27 samples were collected and analyzed , under the direction of A. W. Ambrose , chief petroleum technologist of the Bureau. Valuable assistance was received through the cooperation of oil companies operating in the State , especially the Prairie Pipe Line Co. , and the Empire Pipe Line Co. The present report issued as Serial 2322 , on the Kansas crudes , forms the fifth of the series . Of the four previous papers , the first ( No. 2202 ) deals with crudes from the Eastern fields of the United States , the second ( No. 2235 ) with crudes from the Rocky Mountain district , the third ( No. 2290) gives additional data , cn viscosities and pour tests , for the crudes from these two fields , and the fourth ( No. 2293 ) covers the fields of northern Texas , northern Louisiana , and Arkansas . The details of the methods of collecting samples , making laboratory tests and interpreting results , have been discussed in these earlier reports . It has also been pointed out that the only adequate method of interpreting analyses of crude oils is to compare the individual reports with the analysis of some crude oil that is familiar to the operator . For this reason , no comprehensive discussion of the results of the Kansas survey is attempted, although some general statements may be made .

Feb 1, 1922

By R. A. Beall

Homogeneous zirconium-alloy ingots have been cast on a production basis by the consumable-electrode arc-melting process at the Northwest Electrodevelopment Experiment Station, Bureau of Mines, Albany, Oreg. This paper describes the various methods used to introduce alloying materials into the ingot and evaluates 1 each method by the degree of homogeneity of resulting ingots, as determined in tests on sections cut from the ingots. As many as 30 or more ingots, each 6 to 10 inches in diameter and weighing 300 to 500 pounds, were melted, using each method; and, as most of them subsequently were fabricated to strip 0.1 inch thick, the test results are considered to be representative of production practice. Ingot homogeneity has been considered more difficult to achieve in arc-melting practice than by methods where the molten metal is poured into molds and the addition can be stirred into the total mass of metal before casting. Owing to the unique requirements of consumable-electrode arc melting the addition can be made only to that part of the total mass of the ingot that is molten at one time. Observation of the flowlines in 500-pound ingots produced at Albany indicates that the molten pool has a maximum depth about equal to the ingot diameter. The weight of metal molten at one time is, therefore, not over 100 pounds. Characteristically, the arc-melting process is conducive to segregation, which can be overcome, at least partly, by adding the alloy constituents almost continuously during casting.

Jan 1, 1956

By L. G. Marshall

This report, describing the mining method of the Dresser Trap Rock Co., Dresser, Wis., is one of a series published by the Bureau of Mines on mining methods, performance, and costs at mining operations throughout the United States. SUMMARY Dresser, in Polk County, is 3 miles south of St. Croix Falls, Wis. Company operations are about 1 mile north of the townsite. The mine has been in [peration] since 1914 and under the present ownership since 1949.

Jan 1, 1959

By L. C. IlsLey, R. A. Kearns

"The electrical section of the Bureau of Mines has obtained copies of all available State safety rules and regulations in order to make a study of those portions of the codes relating to electrical equipment. While it has been found almost impossible to compare the several codes as a whole, comparison of those regulations dealing with a single subject has proved both interesting and instructive.Sixteen states have rules or enactments having reference to telephones and the present paper covers a compilation of these references. It is believed that data of this kind will be of service to commissions or other bodies contemplating the revision of existing codes.The compilation taken from the various codes follows: State Rules and Regulations.California.Sec. 5 (Par. c) Telephone communication shall be maintained between a co-operative station and each mine which it supplies. If the foreman in charge of a station does not reside thereat, his residence also shall be in telephone communication with each mine supplied by his station.Sec. 8 (Par. a) Whenever a fatal accident occurs in or about any mine, notice thereof shall be given promptly by telephone or telegraph if possible, followed by a notice in writing to the chief inspector, by the superintendent or other person having immediate charge of the work at the time of the accident."

Jun 1, 1921

By J. M. Riley

A fluorometric method using morin in an alkaline-buffered chelating solution has been developed by the Bureau of Mines for determining beryllium in ores and mill products. Apparatus for measuring fluorescence intensities of the beryllium-morin reaction is described. Preparation of the sample for analysis consists essentially of digestion with sulfuric, nitric, and hydrofluoric acids, fusion of the residue with sodium carbonate and sodium borate, Solution of the melt with sulfuric acid, and proper dilution. Chemical separation of other ions is usually unnecessary. The method rave reliable beryllium determinations on samples in the 0.01- to 0.37-percent BeO range. The method is particularly applicable to low-grade beryllium ores; however, semiquantitative beryllium determinations have been made on beryl containing 12.0 percent BeO.

Jan 1, 1956

By C. Lorimar Colburn

"The use of helmets during the war has accentuated interest in the advisability of using stiff hats in mines to protect the miners against falling rocks. About forty per cent of the accidents in mines are due to falling rocks or roof. A large number of these accidents could be prevented if the miners wore stiff hats or helmets.The use of head protective devices in minas is not new, for they have been in use for many years in Europe and in the Lake Superior District in the United States. In practically all of the mining districts in Europe stiff hats of some kind are required by the mine management. George S. Rice, chief mining engineer of the Bureau of Mines, reported that in Germany, Belgium, and France stiff hats made of papier mache or felt rosin are in use. Similar hats are generally employed in the Lake Superior District. In building the subways of New York and Philadelphia it was the practice of engineers and workers to let the hair grow very long and to wear a close fitting cap or felt hat. In Germany the hats are high like the military helmets, whereas in France and Belgium they fit more closely to the crown. In England the practice is mixed. As a rule the miners use soft padded caps, but in Yorkshire many of the miners use sole leather, tight-fitting caps of jockey pattern with the seam forting a little ridge down the middle of the cap. These hats are very useful allow thin beds of coal, as in crawling one is very likely to strike his head a sharp piece of rock or on a timber. Of course, such mishaps are more likely to occur to a man not familiar with the mine. It must be admitted such hats do not stick on well, though this is usually due to their not being especially fitted. The German hat is particularly unsuited to an American-shaped head.It is interesting to note that on the continent tight cotton caps are generally worn over the hair and under the hard hat. This is a measure for cleanliness which is excellent. In low beds of coal share much crawling on hands and knees is necessary the dirt and coal dust sift down, making the miner black and dirty. In metal mines stiff hats are of especial use in shaft work; also in raises or high stapes. A small fragment of rock falling some distance either down a shaft or raise would kill a man if it struck him squarely on the head. A stiff hat or helmet may protect him and save his life. At a station in a shaft where men are loading the cage or skip, some kind of adequate head protector should be compulsory. A head-protecting hat or cup which is also a good insulator should be worn where there is danger of striking one's head against a wire carving an electric current."

Jun 1, 1920

By Fei Chen, Lesley J. Gaydos, Laurence M. Demers, Douglas C. Kuhn

The fibrogenic effects of silica in experimental animals and humans has been extensively studied (I 7, 20). However, the pathogenesis and molecular mechanisms underlying lung injury and fibrosis resulting from silica exposure remain to be elucidated. It is well-documented that silica can stimulate monocyte-macrophage lineage cells to produce cytokines and growth factors, including interleukin-I (IL- I) (20), tumor necrosis factor-ex (TNF-cx) (I 7), insulin-like growth factor-I (IGF-1) (4), and transforming growth factor-P (TGF-P) (24). Consequently, it has been suggested that the fibrogenic effect of silica may be mediated by cytokines in the fater stages of silicosis. During the early phase of interaction between silica and the pulmonary alveolar macrophage, several direct and indirect lines of evidence suggest that reactive oxygen intermediates (ROI) may play a pivotal role in silica- induced tissue damage (2I, 22). One of the most important components of and contributors to ROI is nitric oxide (NO) produced from L-arginine and molecular oxygen under the catalytic influence of NO synthase (NOS) (I 9). At present, at least three NOS genes have been cloned: a constitutive neuron NOS, a constitutive endothelial cell NOS and an inducible NOS (iNOS) (16). A number of factors have been shown to differentially induce iNOS gene expression in different cell lines including bacterial cell products and foreign antigens. During inflammation, NO is a double-edged sword in terms of the host immune defense mechanisms and the physiologic response to an inflammatory insult. The macrophage is one of the major cellular sources of NO. During the early phase of acute inflammation, NO produced from the macrophage appears to facilitate the clearance of pathogens and promotes a local relaxation effect on the microcirculation of vascular smooth muscle. When the production of NO is left unattenuated, especially under oxidative stress, direct cytotoxic effects of NO can emerge through the formation of peroxynitrite as a result of a reaction between NO and superoxide (2).

Jan 1, 1998

By Murray Jacobson

The Federal Coal Mine Health and Safety Act of 1969 established mandatory dust sampling of coal mines according to procedures prescribed in the Mandatory Health Standards, title 30, Code of Federal Regulations, part 70, published in the Federal Register on April 3, 1970. A laboratory was established in the Pittsburgh Field Health Group of the Bureau of Mines to process the coal mine dust samples collected by the mine operators. This paper describes the laboratory and presents the equipment and procedures used in processing these samples.

Jan 1, 1971

By Oliver W. Keener

This paper describing the methods and costs of mining at the Hartley-Grantham mine of the Century Zinc Co. in the Tri-State Lead and Zinc district is one of a series being prepared by the United States Bureau of Mines can mining practices, methods, and costs in the various mining districts of the United States. LOCATION, HISTORY, AND GEOLOGY The Hartley-Grantham Mine is located just outside the city limits of Baxter Springs, Kans., as shown in Figure 1. A plan of the mine is given in Figure 2, and Figure is a cross section through A - A of Figure 2.

Jan 1, 1930

By J. G. Groetsch

Municipal solid waste (MSW) contains about 8 pct ferrous metallics which are typically recovered by magnetic separators at municipal resource recovery facilities. At present, only about 182,500 ton/yr of MSW magnetics are being processed for remelting out of the -11 MMton/yr discarded. The Sn in MSW magnetics makes this material difficult to recycle to the steel industry. An electrolytic method using stannous fluoborate-fluoboric acid for removing Sn was evaluated. Optimum concentrations of Sn in the electrolyte and the effects of impurities such as Al, Cu, Fe, and Pb on Sn recovery from the electrolyte were evaluated. Operating parameters were 60 to 65 g/L fluoboric acid and 20 to 30 g/L Sn using stainless steel electrodes at a current density of 60 A/ft2. Tests were run with postconsumer scrap4 and MSW magnetics. Good results were obtained with MSW magnetics, after pretreatment by reshredding, magnetic separation, and air classification. The final Sn content of the MSW magnetics scrap was reduced from 0.18 to 0.017 wt pct. Heat and solvent treatments of MSW magnetics to remove coatings did not significantly improve Sn removal beyond that obtained with material that had only been mechanically pretreated.

Jan 1, 1984