Search Documents

By D. A. Reynolds, A. C. Fieldner, S. H. Katz

"03-01-192403-31-2019RI 2591 - Reports of Investigations - Department of the Interior - Bureau of MinesBureau of MinesPittsburgh Experiment Station American Society of Heating and Ventilating EngineersU.S. Public Health ServicesTucson Experiment Station Introduction.""Carbon monoxide self-rescuers,"" or simply ""self-rescuers,"" are pocketsize gas respirators which protect the wearer from air contaminated with poisonous carbon monoxide gas. On March 6, 1924, the Bureau of Mines approved the ""M.S.A. self-rescuer’ manufactured by the Mine Safety Appliances Co., Pittsburgh, Pa., after the M.S.A- self-rescuer bad passed all the tests and requirements of the Bureau's Schedule 14A4.The purpose of the self-rescuer is to help miners to escape from mines in which fires are burning or explosions have occurred, by providing protection from carbon monoxide for at least one half-hour. The self-rescuer can be used similarly by workers above ground who may through accident become surrounded or entrapped by atmospheres containing carbon monoxide.no hazards threaten the miner, who escapes serious injury by fire or violence in a large mine fire namely, ( 1) asphyxiation by poisonous carbon monoxide gas; and (2) suffocation by insufficient oxygen to support life. In order to save himself, the miner must either erect a barrica4e5 against afterdamp and wait restoration of ventilation and rescue or take a long chance at getting out of the mine through entries not permeated by afterdamp.. The self-rescuer removes the hazard of carbon monoxide poisoning for one half-hour or more, and accordingly greatly increases the miner's chance of saving his life.This paper describes the construction and details of the M.S.A. self-rescuer as approved by the Bureau of Mines, and discusses its performance under test condition"

Mar 1, 1924

By Arthur S. Swanson

The DuBois fluorite property in the southwestern part of Hardin County, Ill., has been active intermittently since 1904 and has produced an estimated total of 1,000 to 2,000 tons. The persistence of the vein and the stratigraphy suggested extensions of the ore body formerly mined. The Bureau of Mines investigated the property by core drilling early in 1944. Four holes were bored which totaled 1,106 feet and extended along a strike length of 1,150 feet. The data obtained in the course of the investigation are presented in this report.

Jan 1, 1948

By L. B. Pankratz

The heat content above 298.15° K was determined for crystalline vanadium silicide of the composition V3Si. This substance has a minor thermal anomaly (probably a heat-capacity maximum) near 560° K; the extra heat absorption is about 50 cal/mole. The original heat-content data are presented, and smooth values of the heat content and the corresponding entropy increments are listed for the temperature range from 298.15° to 1,500° K. Equations representing the heat- content values and derived heat capacities are also included.

Jan 1, 1963

By M. O. Renwick, Paul Zinner

"INTRODUCTION In September 1943, the Bureau of Mines conducted a limited program of churn drilling on the Winskell property in the Shullsburg area of Lafayette County, Wis. The work was undertaken as part of a general investigation by the Bureau of the zinc-producing area of southwestern Wisconsin at a time when special effort war being made to increase the production of metals necessary for the war program.Drilling described supplemented a previous drilling program conducted by the Vinegar Hill Zinc Co. The results of both programs encouraged subsequent investigation by the Cuba Mining Co. and eventual development of the Andrews mine.ACKNOWLEDGEMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by such project as soon as praticable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the investigative work, and prepares the final report."

Aug 1, 1947

By W. J. Johnson

This report presents the Phase I progress in the development of a Radar Coal Thickness Sensor (RCTS) being conducted by Boeing Aerospace and Electronics for the Bureau of Mines. A method is developed for measuring both the dielectric constant and depth of the coal shale interface using a modified UHF network analyzer and antennas in proximity to the surface of the coal. Both bistatic and monostatic systems, are compared. The algorithm technique uses synthetic range gating for clutter rejection and full polarimetric scattering matrix techniques to extract the dielectric constant and depth to sub-wavelength accuracies. Tests were run both in the lab and in a coal mine to build an error budget and demonstrate a validation of the model. The development of a prototype radar suitable for coal mine robotics is specified.

Jan 1, 1990

By W. E. Miller, Kennedy. R. E., G. W. Jones

"INTRODUCTION Ethyl mercaptan (CH3,CH2SH), a combustible organic liquid of the thioalcohol type, is employed at an odorant in many types of fuel gases and dangerous atmospheres, which in themselves are devoid of characteristic odors, to give warring against leakage of such gases or atmospheres into places where they might constitute health or explosion hazards.Ethyl mercaptan has a penetrating disagreeable odor resembling that of onions, garlic, hydrogen sulfide, or rotting cabbage, that exceedingly low concentrations of it can be detected. The of odorants as a beans of detecting leakage of gases and atmospheres has been investigated extensively by chemists and engineers of the Bureau of Mines, and numerous reports as to its value have been published."

Jun 1, 1942

By Roger J. Morrell

The Bureau of Mines conducted drag cutting experiments in hard, abrasive rock in an effort to extend the capabilities of an experimental kerf-core mining machine. The basic kerf-core mining machine cannot be used in hard, abrasive rocks because of the high wear experienced by the kerf cutters. These experiments were conducted in an effort to develop a method of preweakening the rock ahead of the kerf cutters in order to reduce the high cutting loads and hence the higher wear rates experienced by the cutters. The two "preweakening" techniques studied were indenting with mechanical wedges and single and double slotting with diamond saws. The best cutter force reduction achieved with mechanical indenting as 70 pct, whereas double slotting achieved force reductions of up to 99 pct. Conceptual designs of preweakening systems that could be retrofitted onto the basic kerfing cutterhead were developed for both the indenting and the slotting techniques. A high-energy impactor with wedge bit was used for the indenting method, and high-pressure water jets were used for the slotting method. A preliminary technical and economic analysis was performed for both of these full-scale systems to illustrate the methodology and to point out the important technical and economic factors that must be considered.

Jan 1, 1987

By J. W. Paul

This paper deals with the second phase of an extensive research on coal-mine ventilation factors. A comprehensive report of the entire work is in course of preparation, but abstracts of the various chapters are being prepared in order to make the results public as rapidly as possible. Part 1 dealt with the resistance of unobstructed entries and was issued as Serial 2621 of the Bureau of Mines, in July 1924. Description of tests. After the resistance of an unobstructed entry to flow of air had been determined by tests in the Experiment mine, mine cars were; run into the test section in various arrangements and the increase in resistance was determined. The cars used were of the wooden type with loose end gate, and would hold about one ton of coal, level full. They were 7 feet long. 4 feet 2 inches wide above the wheels, 3 feet high, and had a cross-sectional area of approximately 10 square feet. The average area of the entry was about 57 square feet, the ratio of unobstructed to total area being about 17.6 per cent. The track gage was 42 inches and the wheel-base 20 inches.

Jan 1, 1924

By Hendrik Gerritsen

The research to be described is directed to the construction of an instrument that detects methane in air. The principle on which it is based is that methane gas absorbs infrared radiation in the wavelength range of about 3.2 to 3.4 micron. Solid state p-n junctions of composition In, .97Ca.03As emitting radiation in a band centered at 3.3 micron were grown by liquid epitaxy on InAs. Fight separate growth cycles and a total of 200 diodes were measured to determine total power, wavelength peak, spectral. half width and reproducibility of the method. In order to compensate for temperature changes, dual emitter systems (one InGaAs, and one InAs diode) mounted on the same TO-5 header were made. These devices were imaged, using a folded optical path cell, on large area InAs detectors, grown by a planar diffusion technique. In the 0-50°C range the primary temperature sensitivity is in the InAs detector rather than in the emitters. Several methods to reduce the overall temperature sensitivity to within acceptable limits were demonstrated. Humidity was shown to have a negligible effect on the measurements.

Jan 1, 1976

By P. G. Clites

This study was conducted to determine the patterns of heat transfer to water-cooled copper crucibles during vacuum arc melting. Values of heat flux from the ingot to the crucible were determined during nonconsumable electrode vacuum arc melting of zirconium and during consumable electrode vacuum arc melting of titanium) zirconium) and steel. The results of these studies con-firm the existence of a high thermal resistance between the ingot and the crucible wall which results from the shrinkage of the ingot as the metal solidifies. Maximum heat flux occurs near the top of the ingot where maximum values of heat flux of 1.4 X 106 Btu/ft2 hr were observed during small-scale consumable electrode arc melting of zirconium and titanium. The maximum heat flux for consumable electrode arc melting of 8-inch-diameter ingots was 0.5 X 106 Btu/ft2 hr. The effects of electrode material) electrode diameter) arc current) and arc potential on heat flux from the ingot to the crucible were studied. Data were also obtained on crucible wall temperatures and on the effect of very narrow annular water jackets.

Jan 1, 1967

By Bill M. Stewart

The Bureau of Mines conducted laboratory tests to determine the effects on the physical properties of coarse coal waste of adding large amounts of fine coal waste. Maximum laboratory dry density, optimum moisture content, shear strength, and permeability tests were conducted on samples that contained 18 to 60 pct minus No.4 (U.S. Standard sieve size) coal waste. For the nonslaky materials, maximum laboratory densities were highest and permeabilities lowest when the samples contained between 30 and 40 pct minus No.4. Shear strength increased rapidly when the proportion of minus No. 4 was increased from 20 to 40 pct, but then increased only slightly or leveled off when the minus No. 4 was increased to 60 pct. Optimum moisture content and permeability were the physical properties most affected by the addition of fines. Optimum moisture content increased as much as 3 pct, and permeabilities decreased up to three orders of magnitude. Slaky coal waste material had physical property reactions to the addition of fines substantially different from those of nonslaky material.

Jan 1, 1981

By BUREAU OF MINES

LIST OF PUBLICATIONS ON CERAMIC INVESTIGATIONS U.S. BUREAT OF MINES .

Jan 1, 1923

By F. L. Wideman

Output of ore and waste from metal and nonmetal mines in the United States continued an upward trend and established a new high. The tonnage of ore handled increased 6 percent over that moved in 1964 and the tonnage of waste rose almost 10 percent. Earth moving by these two activities exceeded 3.2 billion tons, an increase of 7 percent over the 1964 total. Crude material from which metal or nonmetal products were derived continued to be about 75 percent of the total material handled. In 1965, surface mining methods were used to produce about 93 percent of the ore, 99 percent of the waste, and 95 percent of the total material handled. These percentages have remained almost constant since the beginning of this decade.

Jan 1, 1966

By John Nagy

Limited experiments in the laboratory with specimens of mine rock from a Virginia bituminous coal mine indicate that natural gas-air mixtures can be ignited by sparks generated by rubbing friction of sandstone against sand-stone, shale against sandstone, sandstone against (roof-bolt) steel, and shale against steel. Such sparks, generated during a roof fall, may have initiated a recent gas explosion in this Virginia mine, although this cannot be stated with certainty. No ignitions of gas were produced by sparks or heat generated by impact friction between mine rocks or steel, during tension breaks of roof bolts, or by pull tests of roof bolts through their washers and roof plate. However, this negative result of limited experiments does not preclude the possibility of gas being ignited by these conditions.

Jan 1, 1960

By Manuel Gomez

The purpose of this study was to evaluate the feasibility of using statistical response surface regression analysis to predict the sulfur and ash distributions and the washability characteristics of coal along a seam in advance of mining. Prediction equations were developed with experimental data from channel, bench, and core samples from the Pittsburgh coal seam in Greene County, Pa. It was not possible, with the available experimental data, to construct mathematical models to predict ash and sulfur concentrations between sample points. In the authors' opinion, however, the good agreement between experimentally determined and predicted values at given sample points demonstrates the usefulness of the method. More input data, such as geologic information, seam characteristics (rock-to-coal ratio), petrographic analysis, and chemical data, would perhaps make it possible to predict sulfur and ash concentrations and washability characteristics between sample points.

Jan 1, 1970

By A. W. Khair, L. D. Gehl

"This paper describes the study of bit wear characteristics on three types of rock namely Tennessee sandstone, Berea sandstone and Indiana limestone. High content of quartz with quartz cement in Tennessee sandstone causes removal of material from the bit body and dam2ge to the tip of the bit resulting into excessive weight and height loss as compared to other two types of rock. The drum speed and water spray pressure do not contribute significant effect on bit wear. The polycrystalline compact diamond (PCD) tipped bits are more wear resistant than the ordinary tungsten carbide (WC) tipped bits, but, due to wider body of PCD bits, the wear rate increases particularly at greater depth of cut. INTRODUCTIONThe impact of bit-rock interaction during the cutting process in underground coal mines has always attracted the-interests of mining operators, researchers and the manufacturers. Coal cutting bears directly on airborne coal dust generation which causes ""black lung"" in coal workers. On the other hand, rock cutting generates frictional sparks causing face ignitions. The bit wear not only produces airborne rcspirable coal dust , but also affects the productivity, safety and economy. Hun and Evans (J) concluded that the point attack bits have greater ignition potential than the conventional wedge shaped bits. The results of a study (2) suggested that after 7% of weight loss, the bit should be replaced. In a survey study (3), it was found that the bit consumption of bit had an effect on the productivity and utilization of the continuous miners. The mining industry is yet to receive a solution which could provide them with optimum operating parameters for coal cutting machines in underground C9al mines.The study was, therefore, taken up to determine wear characteristics as influenced by the rock propenies and varying operating parameters. For the purpose of this study, three types of rock, Tennessee sandstone, Berea sandstone and Indiana limestone were used. The machine operating parameters included (i) drum speed, (ii) water spray pressure and (iii) bit type. Besides studying the wear characteristics, the effects of these parameters on the required cutting force, specific energy consumption, acoustic emission generation and bit temperature rise were also studied. Also, the preliminary experiments were performed to compare the bit wear between PCD and WC tipped bits."

Dec 1, 1995

By H. N. Smith

IN 1944 the Congress passed the Synthetic Liquid Fuels Act that authorized the Secretary of the Interior, acting through the Federal Bureau of Mines, to conduct basic research and construct and operate demonstration plants to produce synthetic liquid fuels from coal, oil shale, and other substances. As a basis for the oil shale investigations to be undertaken in this country, the progress of foreign countries in developing and using oil shale as a source of liquid fuels was studied by the technical missions of the Federal Bureau of Mines. Oil shale mines, retorting plants, and refineries were visited; geological information on the nature and occurrence of the foreign oil shales was obtained; and samples of the oil shales were collected where possible. Samples collected by these missions or acquired by other means came from Australia, Brazil, Canada, France, Manchuria (China) , New Zealand, Scot-land, Spain, Sweden, Thailand, and Union of South Africa. These countries represent a large part of the locations where oil shale developments have taken place. The major omissions are the Estonian, German, and Russian developments.

Jan 1, 1959

By M. G. Downey

The stone resources in certain localities and the kinds of stone available often influence manufacturing companies in their choice of plant location and in possible expansion of their activities. Limestone in particular is an important raw material for many processing industries. In planning highways and public works and placing contracts therefor, the availability of aggregates and road stone is significant. On the other hand, persons who contemplate entering the stone business or opening now quarries need information as to possible competition. To meet the growing need for regional data of this type, the Bureau of Mines has compiled from its records and presents herein the location of stone quarries by States and counties and by kinds of stone. The list covers all stationary and portable commercial quarry operations whose production statistics for 1940 were reported to the Bureau of Mines but does not include undeveloped deposits and noncommercial or Government-operated quarries.

Jan 1, 1941

By H. W. Wainwright

One phase of the research and development work on synthetic liquid fuels conducted by the Bureau of Mines at Morgantown, W. Va. in cooperation with West Virginia University deals with the purification of synthesis gas.2/ Most of the experimental studies on gas purification have been directed toward the removal of organic sulfur from gas, either catalytically or by adsorption with activated carbon. An important part of the purification program has been the development of suitable analytical methods for determining organic sulfur compounds. As the total sulfur content, organic and inorganic, of purified synthesis gas should not exceed 0.1 grain per 100 cubic feet, the need for accurate analytical methods is apparent. It is also apparent that such methods must be rapid if one wishes to evaluate various processes for removing sulfur from gas. The organic sulfur found in most gas produced from coal is usually present as carbon disulfide, carbon oxysulfide, methyl and ethyl mercaptans, and thiophene, with the exception of thiophene, the remaining organic sulfur compounds respond similarly to catalytic treatment and can be removed effectively. Not only does thiophene resist most catalytic treatment, but it poisons some catalysts, rendering them ineffective in removing the other forms of organic sulfur.

Jan 1, 1950

By J. H. Heginbotham

As part of the total metallurgical system to recover metals from secondary resources, the Bureau of Mines conducted froth flotation research, using cationic reagents to recover glass from urban refuse. Batch flotation tests showed that high-quality cullet can be obtained from glass-rich aggregates derived from municipal incinerator residues and unburned refuse. This was confirmed by pilot plant operations treating 350 pounds of flotation feed per hour. Aggregates containing 85 to 90 percent glass were wet-ground to minus 20 mesh, deslimed in two stages, and fed to flotation cells. The glass was selectively floated using an amine collector, usually in an amount under 0.2 pound per ton of solids in the feed. The glass concentrates from the rougher cells were cleaned by refloating two or three times. Over 90 percent of the glass in the deslimed feed was recovered in the cleaned concentrates.

Jan 1, 1978