Search Documents

By C. H. Elder, Maurice Deul

A 5-hole pattern was drilled from the surface at a site near Oak Grove, Jefferson County, Ala., to degasify the gassy Mary Lee coalbed in advance of mining. Gas and water production was monitored for 1 year, 4 months to allow gas flow to stabilize fully. A thickened water stimulation treatment was designed and applied in one hole of the pattern to evaluate this degasification technique for the Mary Lee coalbed. A gas production rate of 70,000 ft3 /day after stimulation treatment indicates that the use of vertical boreholes coupled with hydraulic fracturing in advance of mining the Mary Lee coalbed would provide for more rapid degasification and could provide a possible source of natural gas.

Jan 1, 1974

By Zachary J. Fink

A continuous-monitoring system has been developed for analyses of mine gas concentrations associated with spontaneous combustion, mine fires, and explosive and toxic levels. The analysis center, which is linked to sample locations by polyethylene tubes in bundles, has been successfully field tested by the Federal Bureau of Mines for analyzing carbon monoxide and oxygen; a computational scheme has been developed to process the data at the site. This report contains information on the design, purchase, installation, and maintenance of the tube-bundle system. A brief comparison of the tube-bundle system with the underground-analysis system and plans for future research are also included.

Jan 1, 1975

By Andrew B. Cecala, Edward D. Thimons, George W. Klinowski

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 1993

By E. G. King

Heats of formation of three crystalline oxides of rhenium (Re02, ReO3 and Re207) have been determined by the method of solution calorimetry, using an aqueous perchloric acid--ceric perchlorate solvent. Copper metal and cupric oxide were utilized as auxiliary substances. Heats were determined at 298' K for the reactions Re + 2CuO = Re02 + 2Cu, Re + 3CuO = ReO3 + 3Cu, and 2Re + 7CuO = Re207 + 7Cu. Standard heats of formation were derived using the value of -37.23 ±0,15 kcal/mole as the heat of formation of CuO. The standard molal heats of formation of the rhenium oxides were determined: Re02, -107.3 ±0.8 kcal; ReO3, -140.8 ±0.9 kcal; and Re207, -301.9 ±1.8 kcal.

Jan 1, 1969

By Maria I. De Rosa

Table 10 and figure 4 show the number of fires and fire injuries occurring at the surface of underground metal/nonmetal and stone mines by state during 1990-2001. Table 10 also shows the injury risk rates, employees' working hours, and lost workdays. A total of 12 fires occurred in 11 states; 5 of the fires caused 5 injuries. The yearly average was one fire and 0.42 injury. Five fires with two injuries occurred at metal mines, five fires with two injuries occurred at nonmetal mines, and two fires with one injury occurred at stone mines. None of the fires involved contractors. The Ewhr value was 58 x 106 hr (Irr = 0.017), and the LWD value was 75. Nevada had the most fires (two fires and no injuries). Ohio, New Mexico, Missouri, South Dakota, and Idaho each had one fire with one injury. Of these states, Missouri had the highest injury risk rate value (In = 0.25). Table 11, partly illustrated in figure 5, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires decreased during most of the six time periods. The number of fire injuries and employees' working hours decreased during all of the periods. The Irr values follow patterns similar to those shown by the injury values. Tables 12-17 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 6 shows the major variables related to fires for 1990-2001. Table 18 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook relates to employment data and injury experience in the metal, nonmetal, and quarrying industries. Combined statistical data on the mineral industries as a whole can be found in volume Ill. Each industry in the chapter is shown separately, and no attempt has been made to combine and show an overall picture. The voluntary reporting of data on injuries and employment by operators of metal and nonmetal mines and quarries has contributed substantially to the promotion of safety in these industries. Data on injury and employment in the clay mining and milling industry are included for the first time. Table 6 contains data for clay mines only for 1955 and for clay mines and mills for 1956. The clay-mill figures are included with other nonmetallic mills in table 5. The information for norunetallic mills was compiled and published for the first time in the 1955 issue of this report.

Jan 1, 1958

By G. L. Oldright, John D. Sullivan

"The present article is the second of a series of papers dealing with the dissolution of copper minerals in various reagents. Work done on the problem has been carried out at the Southwest Experiment Station of the United States Bureau of Mines, in cooperation with the Department of Mining and Metallurgy, University of Arizona. The first paper4 dealt with the dissolution of azurite, malachite, chrysocolla, and tenorite. Preceding articles5 have also dealt with other factors involved in the leaching of copper ores.Cuprite (Cu20) is usually considered as a mineral which is not adaptable to sulphuric acid leaching. Hofman,6 in describing leaching by sulphuric acid, states: ""Cuprite is decomposed into CuO and Cu; and ore carrying cuprite has to be oxidized (weathering, roasting) before treatment."" Greenawalt7 says: ""When acted upon by dilute sulphuric acid, it is partly reduced to metallic copper and partly oxidized into copper sulphate. When heated with strong acid it is entirely oxidized to sulphate."" Work to be described in this article was undertaken to ascertain the conditions whereby all the copper in cuprite could be converted into the soluble sulphate."

Dec 1, 1929

Develop design and support guidelines for coal mine entry intersections based upon results of integrated field and numerical modeling analyses of structural parameters for improving ground stability. Background Underground coal mines contain a large number of entry intersections. Dome-shaped zones over the intersections are unstable and are often associated with roof falls. These roof falls may occur during mine development, trapping equipment and endangering miners. These high-risk areas of the mine account for 10 pct of the total number of ground-failure-caused fatalities. The falls, ranging from heights of 1 to 20 ft, cause high dilution and slow the advance rates. Stability at intersections is influenced by four structurally interrelated parameters: in situ stress, geological discontinuities and physical properties, intersection geometry, and roof span. Because of the complex interaction of these parameters, the actual mechanism of roof failure may vary considerably, depending upon the roof lithology, rock strength, and stress conditions.

Jan 1, 1990

Avoid accidents that can occur when applying belt dressing from an aerosol can, particularly when can pressure has dropped or when spraying against wind. Approach Use a garde-type sprayer. How It Works Commercially available garden-type sprayers can be used for applying conveyor belt dressing from 12 feet away, or more. Pressure is easily raised and maintained at about 50 psi. Most sprayers have a hand pump, but a battery-powered cordless model is also available. Garden-type sprayers are available in various sizes from 11/2 to 18 gallons, with the larger models wheel mounted. The 3-gallon model evaluated by the Bureau has a shoulder carrying strap, which gives additional safety advantages. Use of the strap frees both hands for climbing ladders or holding onto catwalk rails. When spraying, one hand can remain on a handhold to lessen the chances of touching a moving belt.

Jan 1, 1980

By E. G. Valdez

The Federal Bureau of Mines, in cooperation with Ford Motor Co., investigated the recovery of polyurethane foam and other assorted plastics from the nonmagnetic reject of automobile shredders. Preliminary studies were con-ducted on a 1957 hulk augmented with additional foam and assorted plastics. The proposed flowsheet developed by the Bureau from the preliminary studies consists of a combination of screening, water classification, and gravity separation. The process was then tested on reject from two shredded 1972 cars. All of the foam and between 52 and 70 pct of the assorted plastics were recovered. The composition of the reclaimed foam concentrates ranged from 46 to 66 pct foam; the concentrates were hydrolyzed in laboratory tests by Ford Motor Co. to produce a reusable liquid mixture of polyether glycol monomers and toluene diamine.

Jan 1, 1975

By Wilbur I. Duvall

The borehole deformation gage and overcoring techniques developed by the Bureau of Mines form one of the primary methods of determining in situ rock stress. This report describes a least squares method of calculating the average rock stress components in the horizontal plane from more than three diametral deformation measurements in a vertical borehole. This least squares analysis provides a means of determining the multiple correlation coefficient, the variance, and the scatter for a set of deformation measurements. From this information, confidence limits can be calculated for the secondary horizontal principal stresses and their directions. The material presented in this report can be used as a guide to the development of least squares solutions for stress measurement techniques other than the borehole deformation method. Since the statistical information that results from the least squares method is extremely useful in the interpretation of results, it is recommended that a least squares analysis be used on stress measurement data whenever possible.

Jan 1, 1979

By Charles C. Boley

The Bureau of Mines dried and carbonized two wood wastes, one softwood (redwood) and one hardwood (oak), using continuous, vertical entrainment techniques previously developed for use with coal. It was demonstrated that these techniques are readily applicable to wood waste and that appreciable changes in the yields of carbonization products can be obtained by varying operating conditions. A limited amount of experimental work was done on briquetting the charcoals. Firm briquets were formed with oak charcoal, although greater quantities of starch binder than used commercially for kiln-produced charcoal were required. Redwood charcoal did not briquet successfully under the test conditions employed.

Jan 1, 1969

By C. H. Elder

An experimental degasification program using a vertical borehole and vacuum pump to drain gas from the gob area of a longwall panel was successful at Bethlehem Mines Corporation, Cambria Division, No. 33 coal mine. Sixty-one million cubic feet of methane has been exhausted during a 9-month period. Daily production time in the panel increased as a result of lower methane levels in the returns. Removal of large quantities of methane in this way and the exclusion of it from the ventilating system will provide reduced cost in mine ventilation and provide a safer environment for the mine.

May 1, 1969

By E. R. Cole

A lead smelting process that appears to present minimal pollution problems has been developed at the Bureau of Mines, Rolla Metallurgy Research Center. Ten and 100 g samples of PbS mill concentrates were vaporized at 1,000° to 1,100° C in a furnace with an inert gas atmosphere during a 2-hour period. The PbS vapor was transported by the inert carrier gas to the reduction zone of the furnace where it was reduced at the same temperature with excess hydrogen to metallic lead. Lead of 99.9 pct purity was produced. The H2S formed can be decomposed into elemental sulfur and water vapor by a modified Claus process. Approximately 90 pet of the Cu and 70 pct of the Ag and Zn remain in the residue and are potentially recoverable. More than 98 pct of the lead in the concentrates was extracted.

Jan 1, 1974

By Seth C. Schaefer

The Bureau of Mines studied thermodynamic properties of Al-Ni alloys con¬taining 0.54 to 30.04 atomic percent nickel with the aid of the high-temperature galvanic cell Al(1) // Al+3 (AlCl3 in NaCI.KC1) // Al-Ni alloy (1 or s). Activities of aluminum and nickel (compared with pure liquid metals as the standard state) show pronounced negative deviation from Raoult's law at 1,273 K. The properties [?G, ?Gxs, ?G ideal, ?GA1, AGxs1, ?Gni , and ?GNixs] have been derived from the experimental data and are summarized in tables and illustrations. At 1,127 K, the thermodynamic stability for the invariant three-phase equilibrium consisting of a saturated liquid, A13Ni, and A13Ni2 has been uniquely defined by an activity for aluminum of 0.751. A free energy of formation at 1,127 K of -7,940 cal/g-atom was derived for the compound A13Ni.

Jan 1, 1975

By Foster Fraas

In this Bureau of Mines report, use of the photoemission of electrons to produce electric charges for the electrostatic separation of sonic dispersed minerals, which had previously been ground to pass a 43µ-opening sieve, is demonstrated. It appears that many of the oxides, carbonates, sulfides, and arsenides will respond to photoemission. Minerals least responsive are the oxides of silicon, the oxides of aluminum, and minerals that have a high concentration of these oxides. Although several synthetic ore mixtures did not yield to complete separation in a one-stage operation, it is probable that preliminary neutralization of the initial electric charges produced by powder dispersion will provide complete separation. That the separation can be carried out in air and without the use of reagents or heating, which are required in the present practice of electrostatically separating coarse granular feeds, is of special significance.

Jan 1, 1972

By W. L. Staker

The Bureau of Mines investigated methods for selectively eluting mercury, silver, and gold from strong-base anion-exchange resins, including Rohm and Haas resins lRA-430 and 900 and Dow Chemical resins 2lK, SMA-I, and SBR. Resins were typically loaded to 145 oz/st of each metal. Loaded resins were eluted with H2S04, NaCl-H Cl, NaOCl, and NaCl04 solutions. The resins tested had similar elution characteristics for mercury and precious metals. The best selective elution scheme was achieved by eluting in a column with 2N H2S04 to recover 99 to 100 pct Hg, with 200 giL NaCl in IN HCI to rec;ver 99 to 100 pct Ag, and with 2M NaCl04 to recover 79 to 89 pct Au.

Jan 1, 1987

By W. H. Eddy

The Bureau of Mines conducted laboratory batch and continuous flotation processing tests on waste granite fines from South Carolina to determine the possibility of recovering high-quality feldspar and glass sand. Three flotation systems were used for removal of the iron-bearing biotite: Two employed an alkaline anionic-cationic circuit and the third employed an acid cationic circuit. Commercial-grade products were obtained when the remaining biotite was magnetically removed from the feldspar and quartz concentrates. Continuous flotation processing yielded a feldspar concentrate containing, in percent, 3.60 Na20, 5.60 K20, and 2.25 Ca0, with recoveries of 75.3, 66.6, and 72.6 percent, respectively. The feldspar tailing was high quality glass sand containing 98.0 percent Si02 and 0.025 percent Fe203; about 60 percent of the quartz was recovered.

Jan 1, 1972

By L. H. Banning

The Bureau of Mines conducted pioneering batch and laboratory cyclic tests that simulated plant operation in developing a procedure for acidulating phosphate rock with fluosilicic acid. Both high-grade deslimed phosphate rock and low-grade phosphate rock samples were treated. The most promising results were obtained by acidulating des limed high-grade material. In a series of seven cyclic tests, 85.4 percent of the P20S was recovered in solutions. The average P2O5 content of the phosphoric acid-monocalcium phosphate solutions of the first step was 156 grams per liter, and the average fluorine content was 4.7 grams per liter. Residues had an average fluorine content of 30.7 percent and contained 83.9 percent of the total fluorine in the charge materials. Some fluorine was lost by volatilization.

Jan 1, 1975

By K. O. Bennington

Enthalpies of formation of three sodium titanates were determined by hydrofluoric acid solution calorimetry, The values obtained for formation from the elements at 298.15° K are -370.9±0.5 kcal/mole for Na2TiO3, -832.1±0.9 kcal/mole for Na2Ti307, and -1,510.9±1.7 kcal/mole for Na2Ti6013. Tables of enthalpies of formation and Gibbs energies of formation are given as a function of temperature both from the elements and from the component oxides for Na2Ti03 and Na2Ti307.

Jan 1, 1973