Search Documents

By W. E. Wallace, P. S. Mike, C. A. Hill, V. Vallyathan, M. J. Keane

Respirable quartz duet and a kaolin clay dust have been found to be of comparable cytotoxic potential in vitro on a specific surface area basis (Wallace, et a1,1985), despite the distinctly different potentials of quartz and clay for causing pneumoconiosis or pulmonary fibrosis (Sheers, 1984). A respired particle depositing in a respiratory bronchiole or alveolus will contact a pulmonary surfactant hypophase, of which a primary component is diacyl glycerophosphorylcholine, or diacyl lecithin (DPL) (Clements, et al, 1970). Several studies have found that adsorption of such surfactant suppresses in vitro cytotoxic effects of quartz dust (Marks, 1957). Subsequent phagocytosis and digestion by a macrophage may remove the coating, restoring cytotoxic potential and initiating disease processes (Iles, 1979). Adsorption of dipalmitoyl lecithin (DPL) from emulsion in physiologic saline by respirable sized quartz dust and kaolin dusts, and consequent diminution of the dusts' hemolytic and macrophage cytotoxic potential have been reported (Wallace, et al, 1985). This report presents additional data on the cell-free in vitro phospholipase A2 enzymatic digestion of dipalmitoyl lecithin adsorbed on a quartz and a kaolin respirable sized dust (Wallace, et al, 1988) to investigate mineral specific differences in the rates of digestion and of consequent restoration of dust membranolytic potential. Respirable crystalline alpha quarts used was eighty percent smaller than 5 micorometer aerodynamic diameter with a nitrogen adsorption specific surface area of 3.97 m2/g. Respirable kaolin dust was ninety percent smaller than 5 micrometer diameter and had a specific surface area of 13.25 m2/g.

Jan 1, 1988

By L. C. IlsLey, R. A. Kearns

As the use of electricity becomes more and more general in mining opera- tions, interest in regulations governing its application becomes greater. During the past year the electrical section of the Bureau of Mines has made a study of State regulations now in force relating to the use of electricity in coal mines. Technical Paper 271, entitled "State Mining Laws on the Use of Electricity in and about Coal Mines", has been published as a result of this study. The present paper represents a compilation of all laws relating to accident prevention with respect to electrical circuits. This group of regulations is perhaps the most important of any that relate to safety in coal mines. Its importance is shown by reference to accident statistics in Bulletin 115, (Fay, A.H., Coal-Mine Fatalities in United States, 1870-1914, Bureau of Mines, 1916), which show that about 77 per cent of the fatalities due to electricity in and about coal mines were caused by direct or indirect contact with trolley or other power circuits. In actual number this means that of 710 men killed by electricity, 546 were killed by contact with electric wires. Undoubtedly, a large percentage of these accidents might have been prevented had the wires been properly guarded. The compilation follows:

Mar 1, 1921

By H. S. Chiang, S. S. Peng

"SummaryAir velocity distribution surveys on four mechanized longwall faces are presented and discussed. Although there are discernible patterns in the velocity distribution, there are wide differences in distribution in the cases examined. This can be attributed to differences in mining and face geometry. An important factor is air leakage into the goaf.IntroductionOver the past two years several intensive air velocity surveys have been carried out in West Virginia coal mines as part of a programme aimed at understanding dust transport mechanisms on mechanized longwall faces. These are presented here and some of the patterns of velocity distribution are discussed.Ventilation survey methodologyThe air velocity vector consists of three mutually perpendicular subvectors; the vertical subvector is directed toward the roof, one of the horizontal subvectors is parallel to the coal face and the other pointing to the gob. The air velocity which was measured in this paper is the horizontal subvector parallel to the coal face.To record the velocity distributions at the longwall faces, the surveying stations and the surveying points were established as follows.(1) The first station usually was set at the third support from the headentry T-junction. Within the first few supports, the air coming from the intake airway encounters a sharp right-angle turn at the T-junction, and forms a turbulent region close to the coal face. The intake air in this region is also influenced by the motors that drive the face conveyer. But when the air reaches the different. But for the same face the number was the same. The main air-travelling area was divided into six to 12 equally sized sub-areas, and each surveying point was situated approximately at the centre of the sub-area.The velocity survey was carried out by two persons, one reading the meter and the other taking down the readings. A complete survey at one station took about 5-8 min. Usually, the dimension of the cross-sectional area was measured during that time.A third person used the smoke tubes to observe the following: (I) the air movement patterns at different locations; (2) the extent and the direction of the air leakage; and (3) the machines' influence on the main airflow. At the same time he observed and recorded the roof conditions and the compactness of the roof-caving in the gob."

Mar 1, 1989

By H. S. Caldwell

This report describes work by the Bureau of Mines on the vacuum distilla¬tion of some of the more volatile metals such as cadmium, zinc, and magnesium from lead and tin. Evacuation within a distillation apparatus allows rapid diffusion of vapor away from the evaporation surface and prevents reaction of the vapor with residual gases. A reduction of pressure to several tenths of a millimeter makes possible practicable distillation rates, at temperatures for which the partial pressure of the metal vapor exceeds 10-3 atmosphere. The rate and selectivity of distillation depend primarily on the volatility and molal ratios of the alloy metals, and their chemical activity to each other. For very rapid evaporation or low concentration of the more volatile constituent, the rate is determined by the rate of diffusion of the evaporating metal, to the surface of the melt. Cadmium, zinc, magnesium, and tellurium were found to volatilize readily from both lead and tin. Tellurium appears to volatilize as an intermetallic compound rather than the pure metal. Antimony could not be removed from lead at 1,000° C.; the condensate was nearly all lead. Antimony, bismuth, and lead were removed from tin.

Jan 1, 1960

By Paul W. Jeran

Subsidence was monitored by the U.S. Bureau of Mines over the ends of longwall panels operating in the Pittsburgh, Kittanning, and No. 2 Gas Coalbeds of the northern Appalachian Coal Basin. The final subsidence over the finishing ends of three panels in the Pittsburgh Coalbed are compared with the subsidence measured over the rib at these panels. The characteristics of subsidence are different. At Mine A, data over the start of a longwall panel shows similar characteristics to the subsidence measured over the rib. Subsidence over the fmishing ends of panels in the Kittanning and No.2 Gas Coalbeds are also different from the subsidence over the rib. The use of a subsidence prediction model based on data gathered over the rib of a panel will not yield accurate results if it is applied to the finishing end of a longwall panel. Acceptable results may be obtained along the centerline over the starting end of a panel.

Jan 1, 1991

By S. J. Pearce

The Bureau of Mines has prepared, as circumstances have dictated, a series of Schedules setting forth the minimum requirements that various types of equipment should meet to be considered safe and satisfactory for use in certain hazardous or unhealthful conditions. These Schedules cover a wide variety of devices ranging from explosives to electrically operated mine locomotives. This paper deals with those Bureau of Mines Schedules under which respiratory protective devices are tested and approved, and its purpose is to explain the function and operation of these Schedules. Provisions have been made for testing and approval of the following types of respiratory protective devices: Self-contained breathing apparatus,2/ supplied-air respirators,3/ gas masks,4/ dispersoid respirators,5/ and chemical cartridge respirators.6 These devices are tested at the Central Experiment Station of the Bureau of Mines in Pittsburgh, Pa. Self-contained breathing apparatus is tested by the Safety Branch, and the other types of respirators are tested by the Health Branch.

Jan 1, 1951

By F. W. Hoertel

The Bureau of Mines investigated the use of depleted uranium as a sacrificial anode for the cathodic protection of submerged and underground structures of iron , steel , and copper . Uranium-metal couples were tested in simulated marine environments of varying oxygen contents at pH values between 5.5 and 8.5 and under simulated boiler service condition in Rolla , Mo. , city water . Similar couples were tested in samples of Missouri soils to simulate underground service . Uranium remained anodic to iron , steel , and copper in the simulated marine environments and under simulated boiler service if the electrolyte was oxygen- free city water . Uranium appeared to offer limited protection to iron , low- carbon steel , stainless steel , copper , and zinc in the simulated underground tests . Uranium anodes offer a space advantage because 1 cubic inch of uranium gives approximately the same protection as 2 cubic inches of magnesium or 1-1 /2 cubic inches of zinc .

Jan 1, 1963

By Jerry W. Ramsey

The Bureau of Mines studied two Pennsylvania anthracites using low-temperature carbon dioxide adsorption. A modified form of the Brunauer-Emmett-Teller equation was used to calculate specific surface areas. Two mesh sizes of each anthracite were used to determine how gamma irradiation at 106 and 108 rads, both in vacuum and in the presence of air, affected the carbon dioxide surface areas. Results show that anthracites have a system of pores that are essentially all interconnected rather than isolated; that anthracites differ from one another in specific surface, which may correlate with density; and that irradiation in vacuum has no discernible effect on specific surface of anthracite, but irradiation in air does produce changes in specific surface.

Jan 1, 1966

Develop a means of determining both the fill level of material in an ore pass or bin and the location of bridging material causing a blockage.

Jan 1, 2000

To provide a practical method to reduce hand and arm injuries during roof bolting operations.

Jan 1, 2000

Objective: To identify and evaluate a durable, flexible, and practical stopping to direct ventilation airflows in large-opening metal/nonmetal mines.

May 1, 2006

Ever since the problem of mine pollutant waters has been under consideration, different mining methods have been investigated to abate the pollution problem. Two such methods which have been reported are inert gas operation and revised mining methods.

Jan 1, 1970

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

THIS PROGRAM TRANSFORMS FREE FORHATED BRANCH DATA INTO A FORMAT SUITABLE FOR INPUT TO THE PENNSYLVANIA STATE UNIVERSITY MINE VENTILATION SIMULATOR (PSU/HVS 1. BRANCH RESISTANCES ARE ASSUMED TO HAVE BEEN ALREADY CALCULATED, IIOWEVER THIS PROGRAM CAN BE EASILY MODIFIED TO HANDLE THE ADDITIONAL INPUT DATA REQUIRED FOR RESISTANCE CALCULATIONS IN THE PSU/MVSO THE PROGRAM IS WRITTEN IN FORTRAN IV WITH WATFIV.

Jan 1, 1977

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Table

Jan 1, 1977

Objective: To discourage miners from going inby unsupported mine roof by developing intrinsically safe devices that render the attendant hazard more evident, direct a person's attention to read the warning message on the module, and thus avoid the hazard beyond the device.

May 1, 1997

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C 3 Hoist Assemblies (Man rated) A total of nine companies were identified who manufacture and supply man-rated hoisting equipment suitable for below ground installations. 1. The Coeur d' Alenes Company

Jan 1, 1976

By D. O. Kennedy

THIS CHAPTER on minor nonmetals covers greensand, meerschaum, mineral wool, and wollastonite. Mineral wool was by far the most valuable material among these minor nonmetals reported in the United States in 1956. GREENSAND Output of greensand (glauconite) declined in 1956. The Kaylorite Corp., Dunkirk, Md., and the Inversand Co., Sewell, N. J., were the only firms that reported production of this commodity. Output came from open pits in Calvert County, Md., and Gloucester County, N.J.

Jan 1, 1958

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

B 3 Principle Program Nomenclature The principal variable names used in the computer program are defined below. The following dimensions are applicable, unless otherwise indicated. Distance - Ft Velocity - Ft. /Minute Time - Minute

Jan 1, 1976

By Kenneth P. Klouse

The current rulemaking on mine illumination makes it necessary for mine personnel to have an understanding of the behavior of light. They must be able to understand many terms that are new to the industry and must be familiar with the use of various types of photometers. With this knowledge, the enforcement criteria for mines can be understood and compliance can be maintained.

Jan 1, 1976

By T. J. Lutz, G. T. Homce

A standard Ford1 4600 agricultural tractor was converted to remote control to perform ASAE/SAE field upset tests (rear rollover and side rollover). This paper discusses the engineering process to develop a remote-controlled tractor in determining the critical parameters of operation, to choosing appropriate actuators, designing the circuitry to control them, installing the actuators on the tractor, testing the system for functionality and then conducting numerous overturn tests. The system uses off-the-shelf components for simplicity, replaceability, and economic concerns. The remote control system has withstood 21 tests to date with no failures and will continue to be used for at least three more years of testing.