Search Documents

To test the feasibility of hydraulic borehole mining for the recovery of phosphate ore from the deep, water-saturated deposits of northeastern Florida. Approach Phosphate ore is remotely extracted through a Bureau of Mines-developed hydraulic borehole mining system. Hydraulic borehole mining can remove underground ore deposits that cannot be economically mined by the usual open pit or underground methods. It is environmentally compatible, causing none of the surface disruption or ground water pollution usually associated with other methods of mining. Selectivity of the borehole mining system also allows economical recovery of small or discontinuous ore deposits while minimizing the removal of host rock. The hydraulic borehole mining system has been used successfully in the past to mine uranium ore and oil sands. (For examples of these and other applications of borehole mining see T Technology News Nos. 97, 95, 63, 56, and 48) How it Works A 16-inch-diameter borehole is drilled from the surface down into the buried mineral deposit, and the mining tool is installed. The borehole mining tool consists of a 12-inch-diameter pipe string and accessories capped with a three-passage swivel, and ending with a mining section. The mining section has four slurry inlets and an eductor located near the bottom of the section and a single cutting nozzle located near the top. The tool generates a high velocity water jet that erodes and slurrifies the ore. The slurry is drawn through the inlet into the eductor which lifts it to the surface where it is deposited into a slurry discharge sump. All the support equipment is located and operated on the surface; only the mining tool portion of the system is underground during the recovery operation.

Jan 1, 1983

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

Pulmonary inflammation is accompanied by increased microvascular permeability and leakage of plasma into alveolar spaces. Serum has been shown to affect superoxide (O2-) production from pulmonary alveolar macrophages (PAM) in vitro, and in some cases serum has been shown to be necessary for stimulation of PAM. An electro-optical method was used to measure O2- production from single PAM by measuring the reduction of nitroblue tetrazolium (NBT) to a diformazan precipitate (NBTH2) from videorecorded images of individual cells. PAM were stimulated by their initial attachment to culture dishes independent of serum. The addition of 2% serum to the culture medium increased NBTH2 production during attachment, whereas concentrations of 5 and 10% serum had no additional effect. In contrast, PAM incubated for 2 hrs could not be stimulated by phorbol myristate acetate (PMA) or zymosan particles to produce O2- unless serum was present during the incubation and/or stimulation; however, NBTH production was similar in all cases of serum addition. Also2, serum alone did not stimulate adherent PAM indicating that serum is necessary but not sufficient for stimulation of attached. PAM. These results suggest that changes in microcirculatory permeability may have a pronounced effect on superoxide production by PAM and that serum may help regulate or condition these cells during inflammation of the lung. (Supported by USBOM Gll35142.)

Jan 1, 1988

Determine whether the total delay time in blasting may be safely increased beyond the currently permitted 0.5 s, without igniting a methane or methane-coal dust atmosphere and determine the minimum borehole spacing to avoid misfires. Approach At present, regulations limit the delay time used in short-delay blasting to a total of 0.5 s. Many in industry and government would like to see this total delay time increased to 1 5 to permit an increase in the number of different delays available for short delay blasting and an increase in the time between delay periods. The Bureau of Mines conducted research to determine whether the total elapsed delay time for blasting coal in underground mines could be safely expanded, with resulting improvements in productivity. The research was conducted at a surface mine in St. Clairsville, Ohio. Experimental shots were conducted in several pits, each of which had a 5-foot-high coal seam (Pitts-burg No.8) in a 50-foot highwall. The coal seam and a mobile gallery provided a good simulation of an underground coal face. The Bureau also examined the relationship between borehole spacing and misfires, to check on reports over the past few years that permissible explosives frequently misfire. These reports were not well documented, but were numerous enough to warrant investigation. Misfires of permissible explosives in an underground coal mine can be very hazardous; a burning cartridge of explosive may be ejected from a borehole and ignite the gas or dust in the mine, or a misfired cartridge in the muck pile may detonate during drilling and mucking operations, causing serious injuries.

Jan 1, 1986

1.1 Bituminous-Coal and Lignite Dust. - Carboniferous material having a volatile ratio of 12 percent or more by weight and a fineness such that the material passes through a No. 20 sieve. 1.2 Active Underground Workings. - Underground places in which men are required to be or to pass through in the performance of normal mining operations for the production of coal. 1.3 Working Areas. - Underground areas where bituminous coal and lignite are mined, specifically: (a) Face. - The solid surface of the unbroken portion of the coalbed at the advancing end of the working place. (b) Face Area. - The working area inby the last open crosscut in an entry or a room, including the pillar being extracted or longwall being mined. (c) Room. - A place abutting an entry or airway where coal has been mined and extending from the entry or airway to a face. (d) Crosscut (Breakthrough). - Passageways or openings cut through a pillar to connect adjacent entries or rooms. 1.4 Entry. - Underground haulageways, travelways, and airways, except working areas as defined in section 1.3. (a) Active Entry. - An entry in which coal is being mined from a portion thereof or from connected sections. (b) Parallel Entry. - Usually an intake airway parallel to the haulageway. (c) Back Entry. - Usually a return airway parallel to the haulageway.

Jan 1, 1960

By T. F. Morse, R. Lundstrom, A. J. Brammer, D. Peterson, M. Cherniack, T. Nilsson, J. D. Meyer, E. Toppila, G. Neely, N. Warren

HAVIC is a collaboration of investigators from North America, Sweden, and Finland having a scientific mandate from NIOSH, to study the exposure response relationship between vibratory tool exposure and adverse health effects. Five cohorts, the Suomossalmi forest workers cohort, Volvo truck cab workers, Connecticut shipyard workers, and matriculating dental hygiene students and experienced dental hygienists have been under study. In the case of shipyard workers, there was survey and tool exposure data from 1988, although detailed subject testing was only available within the timeframe of the study. The truck cab assembly workforce was an inception cohort that had been followed from 1994 along with age-matched controls. The Finnish forest workers had cumulative health data on a cohort (n=52) that had been studied from 1976. For a subset of these subjects, there was detailed tactometry testing in 1990, 1995, and 2003. Accordingly, there was historical as well as new prospective data for the industrial cohorts. The Suomossalmi cohort was reassembled only for our study, which precluded follow-up evaluation and because of retirement is almost certainly the last time this historic group will be studied. The study features are: • Characterization of the exposure response relationship for hand-arm vibration through a study design, incorporating multiple cohorts, some having existing historical data, • Selection of cohorts to include different types of vibration: oscillatory (forest workers) impact (truck cab workers), high frequency (dental hygienists) and mixed (shipyard workers), • Inclusion of two inception cohorts: dental hygiene students and Swedish truck cab workers, • Methods for multi-site and historical integration A description follows. [ ] Methods The study included surveys, physical evaluation, and a selection of battery of “best tests” (cold challenge plethysmography, multi-frequency tactometry, segmental sensory nerve conduction velocity [SNCV]1,2,3) applied across groups to quantify responses to exposure. Exposure monitoring included exposure characterization through daylong data logging at the individual level. Workers at each site were instrumented with a microcomputer-based Vibration Exposure Monitoring (VEM) system, developed at the Biodynamics Laboratory of UCHC and about the size of a police walkie-talkie, to record user-specific tool-operating times, vibrations, and grip forces throughout all, or a representative part, of their workday. More specifically, data logging methods involved the direct monitoring of work cycles, involving tool operation time and measures of tool vibration, namely the root-mean-square (RMS), root-mean-quad (RMQ), and root-mean-oct (RMO), and grip forces, each calculated per minute. For this study, the questionnaire was homogenized with other vibration studies4,5,6. Cross-translation was directed by the multi-lingual investigators, and then reviewed by the study team. To extend comparability with future international studies, questions were also added from the Vibration Network (VINET) draft questionnaire, the product of a European

Jan 6, 2006

By Yael Miron

ANFO blasting agents may undergo an exothermic reaction when they contact warm ore bodies that contain pyrite and its weathering products. The reaction is very fast at temperatures above 80° C. Urea, when present in sufficient amounts, inhibits this reaction at temperatures below 180° C. But urea-ammonium nitrate mixtures are very hygroscopic and, in certain climates, may be difficult to handle in the field. Reaction-inhibiting characteristics of three compounds were reported by the Bureau of Mines in 1979. Recently, the Bureau investigated the reaction-inhibiting qualities of five additional compounds. Mixtures of ANFO, pyrite, weathering product, and prospective inhibitors were slowly heated, under conditions simulating a hot borehole, to determine prospective inhibitor capability at temperatures up to ~175° C. Small-scale thermal tests of the same mixtures were used for verification and clarification of results. Two organic compounds, phthalimide and xanthine, similar in structure to urea, failed to inhibit the reaction. Zinc oxide and calcium carbonate were found inferior to urea, though zinc oxide raised the onset of reaction from 80° C to about 140° C. Only magnesium oxide was found to be similar to urea in its inhibitory ability at temperatures below 175° C. Based on results from analysis of quenched residues, the use of more than 5 wt-pct magnesium oxide is recommended.

Jan 1, 1982

Maintain good blowing face ventilation while taking deeper cuts with a radio-remote, scrubber-equipped miner. Approach A six week in-mine study of face ventilation effectiveness was made by comparing the existing MSHA-approved blowing curtain setback distance of 25 ft with brattice set back distances of up to 50 ft. Effectiveness was determined by measuring methane levels at the face and in the immediate return. How It Works Blowing ventilation systems are commonly used in mines because the high velocity air stream created by these systems rapidly mixes with and dissipates methane generated during the cutting of coal. A drawback to blowing ventilation is that the work area is placed in return air and this may create dust compliance problems for the shuttle car and mining machine operator. To clean dust from the return a number of mining machine manufacturers supply dust scrubbers built into the machine. Dust-laden air is drawn into ducting at the front of the mining machine's boom and is ducted to a scrubbing unit located on the machine's main frame. The clean air from the scrubber is discharged as a high velocity jet toward the return, generally from the left fender of the mining machine. When taking cuts deeper than 20 to 25 ft with a scrubber-equipped machine, the machine's discharge is in by the mouth of the blowing curtain, creating a concern by mine workers that a loss of air to the face could result. However, Bureau of Mines research found that the push or throw of air toward the return by the scrubber discharge jet allows good face ventilation to be maintained with extended curtain setbacks.

Jan 1, 1984

By M. Townsend, E. L. Petsonk, B. Fedders, M. Niggemeyer, H. Abrons, E. Daniloff, J. Griffin, K. Kinsley

In certain populations, nonspecific airway hyperreactivity (HR) is associated with increased respiratory symptoms and decreased lung function. We analyzed standardized pulmonary symptom questionnaires and pre-shift spirometry with methacholine inhalation challenge (Chatham, M. et al, Chest 82: 15) on 228 control workers (C) with no known exposure to occupational hazards, and 200 underground bituminous coal miners (M). M and c were similar in age, height, sex, and smoking status. HR (defined as >15% fall in FEVI after up to 5 vital capacity breaths of 25mg% methacholine) was found in 25% of M and 28% of C (NS). M showed higher% predicted FEVI (%PFEV) than c (M 107%, C 104%*). 28% of current smokers showed HR versus 22% of never smokers (NS). Current smokers showed reduced %PFEV but were not different from lifelong non-smokers regarding prevalence of HR. Subjects with HR showed reduced %PFEV, (HR 101%, not HR 107%*) but M and c with HR showed similar reductions. M had more dyspnea and chronic cough than c*. Hyperreactivity was associated with increased symptoms in controls but not miners. In our study, the prevalence of HR in coal miners was similar to nonminers, and did not explain miners' respiratory symptoms. * P < 0.05

Jan 1, 1989

By Jürgen F. Brune, William H. Schiffbauer

Communication problems are not new. Research in this area goes back as far as 7922 when the US Bureau of Mines performed experiments to detect radio signals from inside their experimental mine in Bruceton, Pennsylvania. Many improvements to mine communications have been made over the years but for any number of reasons the underground coal mining industry has been behind in implementing advances. Present communications systems far underground mines can be hard-wired or wireless. Both types of systems can fail when faced with fires, roof falls, explosions, and power or battery failure. Currently installed wireless communications systems usually employ a special antenna cable called a "leaky feeder" Fiber optic cables are also used in some applications to form a "backbone" for wireless transceivers. Through-the-earth (TTE) and wireless radio systems are less common. Except for TTE systems, most wireless systems require some wire-bound components, which are susceptible to failure during disasters as cable breakage interrupts communications.

Aluminum alloys are used in two broad classifications: wrought and cast. Wrought alloy products, which are formed into final shape by rolling, forging, extruding. etc., contain low percentages of alloying elements; whereas cast aluminum products, which generally are not worked before use, may contain higher percentages and a somewhat different selection of alloying elements. For example, wrought aluminum alloys usually contain less than one percent silicon and cast alloys contain as much as 18 per-cent silicon. While there are good techniques available for separating aluminum alloys from mixed scrap, there are no efficient ways to separate wrought aluminum from cast aluminum. The high levels of silicon, iron) copper, and zinc from the cast alloys make wrought-cast mixtures unacceptable for wrought alloy production. Consequently, separated wrought aluminum scrap commands a premium price on the market. Since increasing amounts of mixed aluminum alloys are being recovered from automobile scrap, this separation is important for efficient recycling of these alloys. Approach The difference in thermo-mechanical properties between the two classes of aluminum alloys is used as the basis for the separation process. Casting alloys lose their ductility within a certain temperature range while wrought alloys remain ductile. As temperature increases, aluminum alloys gradually become weaker, and at a certain temperature, each alloy loses strength and ductility due to incipient melting in localized areas. For casting alloys that temperature generally lies between 520° to 560° C, but it is above 600° C for most wrought alloys. Mild crushing, therefore, in the proper temperature range will result in complete fragmentation of the casting alloys but only plastic deformation of the wrought alloys. A simple screening step then is used to separate the oversize wrought pieces from the fragmented cast alloys.

Jan 1, 1984

To evaluate the potential for dust reduction, during blasthole drilling, of water or foam applied directly into the drill hole. Approach The Bureau of Mines tested a through-the-drill-steel water and foam injection technique in two noncoal mines to evaluate the method&apos;s potential for greater dust reduction. The tests were performed by drilling a series of blastholes for an entire face (a 90 minute time-period). For the first 45 minutes of drilling, foam or water was applied through the drill steel. Blowing ventilation was supplied to the entry about 50 feet from the face. The dust concentration measurements were made by a Real-Time Aerosol Monitor (RAM-I), and the data were read out on a strip chart recorder. The evaluation test results showed that the water or foam injection technique, when used on localized dust sources, can be an extremely effective dust control method. Small amounts of water used in this method have also allowed it flexibility to be used in water-soluble ores such as salt, gypsum, anhydrite, and trona. How The System Works Water or foam is mixed with compressed air (approximately 100-120 psi) with suitable metering systems and forced through the drill steel into the blast hole at the point of dust generation. Because the water or foam is applied at the source, minimal quantities of liquid are needed (0.2 to 0.6 gpm). These low flowrates are sufficient to just moisten the dust emerging from the blast hole, thus eliminating a major source of airborne dust. The wet drilling procedure also eliminates a second source of dust. With dry drilling, the dust from the blast hole falls to the floor. Since this can be a 15-ft drop or more, the impact can send the dust billowing up from the floor, adding to the airborne dust. With wet drilling, the moistened dust merely dribbles down the face.

Jan 1, 1982

Control respirable dust in underground coal mines through selection of optimum water spray pressures. Approach Through underground trials at longwall and continuous mining operations, the relationship between operating water spray pressure and respirable dust levels at the machine operator&apos;s location was determined. Defining the Application Water sprays are used for two significantly different control applications. On longwall mining machines, sprays are commonly installed both on the body of the machine and on the cutting drum. Sprays on the body of the machine are used to redirect dust which has already become airborne away from the machine operator. Each spray acts as a small fan, directing the primary airflow over and around the machine and towards the face, away from the operator. The energy of this system is directly related to the spray pressure. Higher pressures move more air, but care must be taken not to cause turbulence and boilout into the walkway. Sprays mounted on the drum are, effective at suppressing the respirable dust at the bit/coal interface and preventing it from becoming airborne. Again, these sprays must not impart excessive energy to the dust particles thus stirring up more dust than they suppress. While mounting sprays on the shearer drum is standard industry practice, there is no reliable technology available to successfully mount water sprays on the cutting drum of continuous miners. Instead, sprays are mounted on the machine body, close to the drum, and directed at the cutting head. This allows the water to reach the bit/coal interface and mix with the cut material. Here again, care must be exercised to prevent these sprays from imparting excessive energy to the dust particles and stirring up more dust than they suppress. These sprays can also cause dust "rollback" from the face, toward the operator, if operated at too high pressures.

Jan 1, 1986

Many different types of structures and materials have been used to build mineral processing facilities throughout the years. Although structure type and building material were not viewed as significant factors affecting the health of employees in these facilities when they were built, the National Institute for Occupational Safety and Health (NIOSH) has found that building type can impact respirable dust and noise levels. NIOSH performed a study in which it evaluated three building types: masonry, an open-structure design, and a steel-sided design. This study indicated that an open-structure design (no walls) was superior from both a dust and noise (health) standpoint when compared to the other two structure types. Therefore, companies may want to consider this design when building new structures.

By Edmund S. Leaver

This information circular is written is response to the marry requests for information on the recovery, or reason for poor recovery, of fine gold by the amalgamation process. Checking Gold Content Experience has shown that in many cases error has been made because the true told content of a particular sample or deposit was not known. Fire assays of representative samples give accurate results and should be considered final in determining the gold content.

Jan 1, 1928

? A roof bolter reaches for a lever while guiding the drill with his other hand. Since he&apos;s watching the drill and many of the controls look and feel alike, he hits the wrong control and crushes his hand. ? Six hours into the night shift, an ore truck driver dozes off. The truck plows over the berm and down into the pit. ? Fleeing a afire, a face crew sees smoke in the intake entry. Assuming the fire is ahead, they cross over to another entry, but soon encounter even worse smoke. These very different accidents have at least one factor in common: the human factor. The actions, decisions, thoughts, or perceptions of one or more humans contributed to the accident. These are just a few examples of safety problems researched by the Human Factors Group of the Pittsburgh Research Center, U.S. Department of Energy.

Jan 1, 1998

By Martin Berman

The Bureau of Mines has investigated the mineral matter content of 38 American coals using X-ray fluorescence. Measurements of the Ka intensity for magnesium, aluminum, silicon, sulfur, calcium, and iron permit the determination of those elements as well as an indirect determination of the ash con-tent of the coals. The percentage of each of the six elements was corrected for absorption by all six elements as well as by hydrogen, carbon, nitrogen, and oxygen. It made little difference whether the values used for hydrogen, carbon, and nitrogen were obtained from chemical analysis or whether average values for all coals were used. In all cases, oxygen was obtained by difference. The correction for absorption by all these elements involved the inversion of a 6 X 6 matrix and was performed by computer. Assuming that the elements magnesium, aluminum, silicon, calcium, and iron were present in the ash as oxides, the quantity of ash was determined. The results for the mineral elements as well as for ash and oxygen were in good agreement with chemical results. Particle size was found to have a significant effect on fluorescence intensities. A study of size effects was made for pyrite particles, since the sulfur content of coals is of particular interest. Theoretical equations were derived and verified relating the intensity to particle size. It was found that the coal samples must be ground to less than 2 microns. Sulfur appears in several forms in coal, and the effect of sulfur form on intensity was investigated. It was found that the Ka intensity was independent of sulfur form but the Kß intensity varied with the type of sulfur. Thus, the Ka intensity was used for determination of the quantity of sulfur present. Utilization of the sulfur KB intensity did not permit a determination of the proportions of sulfur forms present in coal. However, for synthetic mixtures of cystine and pyrite in carbon black, measurement of sulfur Ka and Kß permit determination of each constituents from measurements of sulfur intensities alone.

Jan 1, 1968

Roof bolting is a slow, expensive, and absolutely necessary mining activity. Roof-bolting activities also account for the largest percentage of lost-time injuries in underground coal mines. Dull bits result in the application of excessive force, which bends drill steel; and changing starter and finisher steel was the most significant source of injuries associated with roof bolting. The tungsten carbide (WC) roof-bolt drill bits currently used in American, Canadian, and Australian coal mines are capable of drilling only one or two 4-ft holes and then they are resharpened once or twice to drill another one or two holes. Often, in medium-hard rock formations (sandstone), as many as 20 to 30 bits may be required to drill a single 4-ft hole. Objective To compare the performance, longevity, and cost of newly developed polycrystalline diamond compact (PDC) roof-bolt drill bits against WC bits. Research and Background Diamonds for industrial use have been scarce throughout history and continuous attempts have been made to produce synthetic diamonds. The first synthetic diamonds were manufactured in 1953. Economically produced synthetic diamonds are 1 to 10 µm in size, but in this size range, they are totally unsuitable for industrial applications. In 1972, General Electric Co. developed a process to sinter the artificially developed, minuscule diamond particles into usable products. In this process, several layers of diamond-particles-and cobalt mixture are overlaid on WC substrates and sintered at 2,350° F and 1,000,000 psi. The final product is known as PDC. Today, PDC&apos;s are available in many shapes, but their size is limited to 3/4 in, or less, in length or diameter, because pressures greater than 1,000,000 psi are required to manufacture larger PDC&apos;s. At present, diamond and PDC arc the hardest and strongest commercial materials available for wear surfaces. The PDC used in this study had a hardness 3.61 times greater than that of WC.

Jan 1, 1992

1. COAL PRODUCTION: Under Section 402 of Public Law 95-87 (SMCRA), coal operators are required to pay a fee when coal is sold, used, or transferred. These fees are deposited in the U.S. treasury as the Abandoned Mine Land Fund. Information about the type of coal (bituminous, lignite, or underground) and tonnage are tabulated on Form OSM-1 and submitted with the fee, which is paid quarterly to the Office of Surface Mining. The coal production data presented in this report was compiled from information stored in the Office of Surface Mining Fee Collection System computer data base. Collection of the fee began with the last quarter of 1977; therefore, 1978 data includes the last quarter of 1977 and the first three quarters of 1978. Information for each successive year follows the same tabulation pattern. Surface production includes both bituminous and lignite coal; underground includes tonnage reported as underground mined. In New Mexico and Montana, coal production on Indian land is listed under the Crow, Hopi, and Navajo Tribes. 2. HISTORIC COAL PRODUCTION: Federal Government agencies have published coal production data since 1807, the date of the earliest record. The source of coal production data used to compile this graph was: 1891-1895, U.S. Geological Survey, Division of Mineral Resources; 1896-1977, U.S. Bureau of Mines annual Minerals Yearbook; 1978- 1991, Office of Surface Mining data described in footnote 1 above. 3. NUMBER OF MINES: The number of mines was compiled from Office of Surface Mining Fee Collection System data described in footnote 1 above. Annual totals were calculated by adding together the number of operations with the same Mine Safety and Health Administration numbers reported each quarter and dividing by four to give an annual number in each state. 4. ENFORCEMENT ACTIONS: Enforcement action data was compiled from annual reports developed by Office of Surface Mining field offices and historical field office records. The data presented are all actions taken by both the state regulatory authority and the Office of Surface Mining. Citations issued are the sum of Notice of Violations (NOVs) and Cessation Orders (COs). Because the Hopi and Navajo jurisdictions overlap in Arizona and New Mexico, enforcement actions data for the tribes have been combined in annual reports prepared by the Albuquerque Field Office; therefore, they are combined for this report and listed under Navajo Tribe. 5. ACREAGE PERMITTED: Acreage permitted data was compiled from annual reports developed by Office of Surface Mining field offices and historical field office records. The acreage listed was permitted during the year shown and is not the total acreage under permit during that year. 6. BONDS RELEASED: Acreage of reclamation bonds released was compiled from annual reports developed by Office of Surface Mining field offices and historical field office records. The sum of final Interim Regulatory Program bonds and Phase 111 (or final release) bonds shows only the land area where reclamation is complete and has been released by the regulatory authority.

Jan 1, 1992

Reduce the costs associated with conventional treatment of acid mine water. Approach Conventional treatment of acid mine drainage consists of plants requiring large mixing and aeration tanks, mechanical aerators and large, shallow settling ponds. Such plants are usually very costly to construct, maintain and operate. The Bureau of Mines has developed a simple, low-maintenance, highly efficient system to treat acid mine drainage which mixes, aerates, and neutralizes mine water Simultaneously in the existing discharge pipeline by using the pressure generated by the deep mine discharge pumps. The mixing and aeration action of the in-line system significantly increases oxidation rates of ferrous iron. Iron and manganese are removed, even at near neutral pH levels, due to the high efficiency of this system. How It Works The In-line Aeration and Treatment System (ILS) consists of two commercially available components, a jet pump (ejector) and a static mixer. The jet pump is simply a nozzle that converts water, already under pressure, into a high-velocity stream that entrains air by Venturi action. If neutralization is required, sodium hydroxide or lime is added along with the air at the Venturi opening. The aerated and neutralized water then enters the static mixer, which is a length of internally spiralled pipe that mixes air and water together. The two components, which are both about 8 feet in length, replace the last section of discharge pipe at a point before the mine water is emptied into a pond. Along with the settling pond, these components treat the water so that it meets discharge criteria. The system has been used at surface drainage treatment facilities as well, but in such use a pump is required to provide the necessary pressure drop across the Venturi opening.

Jan 1, 1985

The investment involved in any communication system represents a considerable sum. Even though it is desirable that the system work properly each and every time it is called into use, some failures are bound to occur. Most failures, however, and especially those that occur most frequently, are due to poor installation techniques. An extra hour spent at an installation site can save many maintenance trips and many frustrating hours of system troubleshooting. Typical faults likely to cause communication outrage are Pager phone systems Poor splices aggravated by corrosion. Strain relief not provided. Drip loop not provided. Incorrect branch connections. Overloading the circuit. Poor battery connections. Improper wire size or type. Lightning strikes. Improper placement of wire runs. Carrier phones Mounting transceiver near load resistors or other sources of heat. Tracks not electrically bonded. Cable abrasion due to poor mounting location. Disconnected battery. Poor mechanical installation. Each installation should be well planned. After an installation is completed, the technician should ask the question, "What can go wrong with this unit or line?" Remember the adage, "Whatever can go wrong, will." Preventive measures taken during installation will pay off in the long run. 6.2 Pager Phone Installation The pager phones used in many underground coal mines are battery-operated, party-line telephones with provisions for loudspeaker paging. The system is usually two-wire, nonpolarized, and operated by self-contained batteries. Many of the individual units are certified as permissible. 6.2.1 Mounting Pager phones are designed to be mounted on an upright support at the desired location. For convenience, the phone should be mounted 5 feet above the floor where there is no obstruction to using the handset or removing the cabinet front cover for servicing or battery replacement. In low-coal situations, a suitable height for installation should be selected convenient to the normal operator&apos;s position at the site selected. About 12 inches of free space on each side of the phone should be provided for cabinet access. The phone should be protected against direct exposure to dripping water and should not be allowed to rest in a puddle of water. The mounting location should be convenient to a work location and have a safe, unobstructed area for a worker to stand and use the phone. The phone must be in a location where the worker will not be in the path of moving vehicles or falling debris. Each telephone is normally well insulated, but it is still good practice to provide an insulating mat or dry planking for the user to stand on.

Jan 1, 1984