Search Documents

By D Olivier

De Beers' Finsch Mine is situated in the Northern Cape province, 170 km northwest of Kimberley. The concentrator facility, designed and constructed by Bateman Engineering, was commissioned in 1967 and upgraded in 1979 using diamond liberation and extraction technology available at the time of design. Since then significant advances in diamond processing and technology have been made and these -have been incorporated into the new main treatment plant and recovery plant flowsheets, making diamond liberation and recovery from the Pre-1979 dumps a viable economic option at Finsch."

Jan 1, 2010

By K. Cole, D. Mesa, P. R. Brito-Parada, M. R. van Heerden

Turbulence in stirred tank flotation vessels determines the bulk transport of particles and has an important role in particle-bubble collisions necessary for attachment. Positron emission particle tracking (PEPT) produces quantitative measurements of the kinematic motion of different particle classes inside flotation vessels. This paper presents flow profiles of the vessel, residence time distributions, flow profiles through the mesh and macroturbulent kinetic energy distributions as experienced by valuable (hydrophobic) mineral particles in a laboratory scale flotation vessel. The results highlight the impact of the rotor-stator design and a retrofit mesh modification at the upper part of the vessel which improve recovery by decreasing turbulence in the quiescent zone and at the interface. Keywords: Flotation machines, turbulence, PEPT

Jan 1, 2020

By A. C. Lawrence

A new approach to the -study of human factors in stope productivity by A. C. LAWRENCE B. Econ., D. Com. (S.A.) (Member) The extent of the improvement in mean performance which could be achieved by reducing the variance between stoping gangs is examined, and it is shown that a worthwhile gain would result if variance were reduced by as little as 5 to 15 per cent. The problem of identifying human factors which contributed towards variance in gang performance was examined in one gold mine. A total of 342 'observations' on 49 stoping gangs were gathered, each observation consisting of a set of figures for 36 variables for one gang for one week. The variables included 'stope factors' such as face length, 'gang factors' such as the ethnic composition of the gang, and 'supervisory factors' such as the experience of the miner. These variables were related to 'tons trammed per week' as a measure of work performance. The findings showed that certain of the predictor variables accounted for 66 per cent of the variance in gang performance and about two thirds of this could be attributed to gang and supervisory factors, that is to the 'human factors'. The method suggests a basis for a new approach to the identification of human factors and is a promising step towards optimizing gang performance.

By R. C. Nkhoma, K. A. Annan, S. Ngomane

The effects of welding current, electrode force, and welding time in a resistance spot weld were studied to investigate the effectiveness of welded joints between a thin EN10130: DC04 material and a thicker 817M40 part, through analysis of the microstructural and mechanical properties. All welded specimens were subjected to tensile testing at room temperature (25°C) and sub-zero temperature (–46°C) to test the strength of the welded joints. No full button failure was observed at either room temperature or sub-zero temperature after optimization of the weldng parameters. The fusion zone was observed to consist mainly of martensitic phase, due to rapid quenching, while the HAZ was composed of clusters of martensite in a ferrite and bainite matrix. The base 817M40 metal remained fully ferritic after welding. The hardness was found to increase with increasing welding current. An increase in nugget size, indicating good fusion of the weld, was observed with an increase in the welding current.

Oct 1, 2021

By L. Chanderman, C. E. Dohm

"Mineral Resource estimation (MRE) and classification are highly dependent on the confidence in the model of the orebody geometry, known as the geological model, within which the estimates are constrained. An understanding of the geology of a deposit is thus fundamental to the Mineral Resource evaluation process. The geological model is a function of the structural and depositional complexity of the geology captured by drilling information, which is limited in the early stages of a project. The information effect has a significant impact in terms of the interpretation of the geology as well as the estimation of grade continuity and the resultant risk associated with the Mineral Resource estimate and classification.Therefore, as new drilling information becomes available, it is necessary to update and refine the geological model to appropriately constrain the resource estimates. The grade information is also updated, including statistics and the spatial correlation characteristics. This refinement is based on geological interpretations derived from the drillhole information that becomes available throughout the life of the mine; orebody knowledge that comes from working experience of the deposit, as well as familiarity with the software package used for modelling, is also important.In updating, the potential to identify new resources in previously unknown areas may be realized. The opposite may also occur where previous interpretations of ore continuity are refuted. Both scenarios could result from a better understanding of the geology of the deposit and thus a more realistic MRE, which reduces geological risk. This paper describes how newly drilled advanced grade-control holes for a gold deposit in Mali were used to refine the 3D geological model for the deposit in an attempt to identify the potential for additional oxide ore using conventional geostatistical evaluation techniques."

Jan 1, 2017

By S. Banisi, A. Ghasemi, A. Fazeli, M. Rezaei, M. Maleki-Moghaddam

The efficiency of high capacity SAG mills which consume large amounts of energy depends on the grinding and slurry discharge systems. A 9.7 m × 4.8 m SAG mill with radial pulp lifters is used at the Sarcheshmeh copper complex grinding circuit. The process audit indicated that the pulp discharge system was not efficient, judging by the amount of slurry flow back and carry over. These events limited the discharge rate and increased the wear rate of the lifters and grates. With the objective of finding a new design for pulp lifters, a 3D DEM software (KMPCDEM ©), along with the plant operational data and photographic evidence was used. The KMPCDEM © software was used to compare the efficiency of the radial and curved pulp lifter design based on the material flow. The slurry flow was analysed in terms of ease of discharge and lifter wear rate. It was found that changing the radial pulp lifters to curved pulp lifters could improve the discharge efficiency,and decrease wear rate of the pulp lifter in particular at the base of the pulp lifters. The simulation results showed that if curved lifters with a radius of 0.3×mill radius are used, the amount of slurry flow back and carry over will be negligible. It is predicted that by installing the curved pulp lifters, the capacity of the mill increases by 10% and the pulp lifter service life improves by at least 20%. Keywords: SAG mill, radial pulp lifter, DEM,curved pulp lifter, Sarcheshmeh

Jan 1, 2020

By T. Wajima

Recovery of precious metals from hydrochloric solution using sulfur-impregnated carbonaceous adsorbent was examined. Sulfur-impregnated adsorbent with adsorption abilities of precious metals can be prepared from activated carbon using pyrolysis at 600 oC under 10 % H2S gas flow, and the adsorbed Au and Pd were precipitated as metal phase on the surface of the adsorbent. The adsorbents after precious metals adsorption were burned at 700 oC to obtain the residue mainly containing precious metals. The adsorbent was found to be highly efficient and selective for the uptake of precious metals, especially Au, in the presence of excess base metal ions from simulated spent automotive catalyst eluted solution using a column pack test. Keywords: Gold, platinum, palladium, reduction precipitation

Jan 1, 2020

By M. Z. Naghadehi, F. F. Nasategay, J. Sattarvand, R. Battulwar, E. E. Gohari

After the recent increase in catastrophic failures of tailings dams such as the Burmadinho, Brazil failure in 2019, the mining industry has actively engaged in the stabilisation of tailings dams. Most of the tailings storage facility (TSF) guidelines suggest a laborious action that can be facilitated through imaging by unmanned aerial vehicles (UAVs). Although UAVs are not unknown to most mining operations, automated rill detection through aerial image processing is a new concept. This study utilises images from sites in the U.S. and employs semantic segmentation with a UNet architecture to detect location and size of these rills. The developed model can be used as a tool for monitoring surface erosion of TSFs.

Sep 1, 2021

By J. Bal, V. D. Dao, W. Li

"SynopsisThis study proposes a methodology for evaluating the risk of coal bumps in multiple-seam longwall mining. Both the stress field and the total energy release (TER) during retreat were evaluated in the specified case involving multiple-seam mining using the LaModel program. The results of numerical simulations indicated that both the peak vertical stresses on the panel edges and the peak TERs in the outby longwalls increased significantly as the horizontal offsets were reduced from 60 m to zero. With the comprehensive consideration of the stress field and TERs, a conservative offset of 60 m was ultimately adopted when developing the gateroads of the lower panel in the field. The field measurements indicated that coal bumps were avoided completely by employing the proposed design, and the maximum roof-to-floor and rib-to-rib convergences of the tailgate during retreat were only 360 mm and 576 mm, respectively.IntroductionCoal bumps – sudden, violent bursts of coal – pose a serious threat to the safe excavation of coal. Their occurrence depends on the properties of the surrounding rocks, stress field, and dynamic disturbance. The complexity of the mechanism of coal bumps is further enhanced in multiple-seam mining due to seam interaction. Multiple-seam mining is most frequently found in the coalfields in eastern China, such as Xuzhou, Xinwen, Zaozhuang, and Huainan. In the past, due to issues of availability, economics, and ignorance of the potential risk in multipleseam mining, coal seams in such conditions were mined without proper planning to account for seam interaction. Fortunately, studies published over the past three decades have raised awareness of the problems associated with multiple-seam mining, and indicated that the ground control issues induced by multiple-seam mining can be avoided and/or minimized with proper planning.A number of technical studies pertaining to the design of multiple-seam mines have been published. These studies can be divided into two groups based on their methodologies of design: empirical (Chekan and Listak, 1993; Haycocks and Zhou, 1990, Matetic et al.; 1987a, 1987b) and numerical approaches (Li et al., 2000; Maleki, 2007; Mark, 2007; Peng, 2007; Zipf, 2005). The majority of the extant studies on the interaction mechanisms in multiple-seam mining have focused on the load transfer during operation, resulting in the proposal of the pressure bulb theory (Forrest et al., 1987; Haycocks and Karmis, 1983; Peng, 2008; Peng and Chandra, 1980) and pressure arch theory (Holland, 1973; Oram and Ponder, 1997) to guide multiple-seam mine design. However, neither, of these theories can be used to evaluate the potential for coal bumps."

Jan 1, 2015

By L. Gutierrez, R. Yepsena

Enargite in porphyry copper deposits is an important mineral as it displays good floatability under the presence of the collectors usually used in the flotation of copper sulfides. As a result, copper concentrates grades are reduced. As scarcity of water resources is a problem relevant to Chilean mining, the use of seawater is a feasible solution. The behaviour of copper sulfides and molybdenite in the process of flotation in seawater was previously studied but not for enargite. The objective of this research is to study the behaviour of the enargite in different conditions of electrochemical potential during the process of flotation using seawater. The study was carried through micro-flotation tests using pure samples of enargite, at Eh values ranging from -300 to 500 mV(SHE), both in seawater and aqueous solutions containing calcium and magnesium. The results show that at pH 10.5 in seawater, the enargite and chalcopyrite recoveries are reduced throughout the whole range of Eh studied. At pH 9 in seawater, enargite and chalcopyrite are depressed under reducing and slightly oxidising conditions. The recovery of both minerals drastically decreases at Eh values lower than -100 mV and greater than 400 mV. The behaviour of enargite in seawater flotation differs from that observed in conventional water, since in the latter case the recovery of enargite decreases at higher potentials close to 500 mV. Keywords: Enargite, flotation, seawater, redox potential

Jan 1, 2020

By K. M. Banks

The hot ductility of in situ melted tensile specimens of micro-alloyed steels having C contents in the range 0.12?0.17% (mass %) have been examined over the 700?1000°C temperature range. An improved testing method for simulating the continuous casting process was used, which takes into account both primary and secondary cooling conditions. Increasing the N content to electric arc furnace levels (0.01% N) was found to cause a serious deterioration in ductility. V-N steel gave better ductility than Nb-containing steels due to less precipitation. From a cracking perspective, low- N steels are generally recommended but, when not feasible, a combination of Nb and V gives even better ductility. However, to be sure of avoiding transverse cracking in higher N steels a small addition of Ti is required. This resulted in a decrease in the fraction of fine particles and in accord with this better ductility. Transverse cracking of industrial slabs was then avoided.

Jan 1, 2011

By D. Saramak, T. Gawenda, A. Stempkowska, Z. Naziemiec

The aim of the paper is to discuss the possibility of producing aggregates with an increased content of regular particles, as well as to present a method of aggregate production which has not previously been used in the industry. Traditional aggregate production circuits require the application of three or four grinding stages (depending on the particle size of the feed), but for fine particle fractions of aggregates, irregular grains occur on average with a content of 10%. The innovative technological circuit can produce the aggregates with the content below 3%, even in a single- or two-stage crushing circuit. Downstream jig beneficiation of such prepared material results in higher separation sharpness, lower probable error index (Ep) and imperfection (I). Keywords: Aggregate production, jig beneficiation, mineral processing, raw materials

Jan 1, 2020

By D. Minson, G. Lindner, S. Miskovic

Thickening is an essential process in the mining industry and currently one of the most costeffective technologies for recovering water from tailings streams. Improved performance of thickeners can lead to significant energy savings, and increased recovery of water close to the mill. Its performance is directly affected by the rheological properties of slurry at the raking zone. To further understand the dynamics of slurry inside thickeners, a multiphase particle-in-cell method (MP-PIC), is used to investigate its behaviour on a sliding channel. Parameters like particle-size distribution (PSD), rheological properties, and domain discretisation were benchmarked to study its influence on highly dense flows. The slurry concentration by weight of the samples ranged between 60 to 70% of solids by mass, under which conditions it is known to behave like a non-newtonian fluid. An experimental flume, 0.2 m wide and 2 m long, was used for validation under different angles and slurry composition. Visual analysis of the slurry height and shape, as well as velocity measurements, were compared with numerical data. The preliminary results show the ability of MP-PIC method to represent different types of highly dense flows, while still being computationally affordable and practical for industrial use. Keywords: High density thickener, CFD, MP-PIC, multiphase-flow

Jan 1, 2020

By S. Langea, H. Lieberwirth

Impact crushers are common machines in comminution plants. Their high size-reduction ratio and relatively simple design, make them a preferred tool even when subjected to harsh wear, and producing a large quantity of fines in some applications. Until now the alignment of the operational parameters was an operator’s responsibility. Due to the random process characteristic this is mostly done based on empirical values and sensor data, such as power consumption. This paper describes a new approach for online process monitoring of the horizontal-shaft-impact crusher. The application of robust, low-cost acceleration sensors enables the permanent observation of the process characteristics. The operational and evaluation methods are determined on the basis of experiments. Subsequently the recorded measurements are analysed in regards of throughput, rotational speed and product particle size distribution. Occurring signal characteristics are described based on physical and technical principles. The measured data of the acceleration sensors at varying operation conditions provide insight in the course of process. The accurate utilisation yields the determination of the preferential process conditions providing the best balance between the pros and cons of an impact crusher. Both the experimental method and the data processing is discussed from a scientific perspective, displaying a completely new approach for the operation of impact crushers. Keywords: Impact crusher, acceleration sensors, data processing, particle size

Jan 1, 2020

By G. M. Evans, S. Mitra, A. V. Nguyen

As an alternative to the conventional flotation method, there has been continual research in an effort to enhance base metal ores and combustibles recovery using ultrasonics. These studies however were largely limited to the pre-treatment of ores for the removal of surface contaminants while the effect of ultrasonics on the bubble and pulp-phase interactions remained somewhat unexplored. Noting this deficiency, this study aimed to investigate the mechanistic effect of an ultrasonic field in an impeller less flotation cell specifically focusing on the bubble-particle interaction dynamics. A lab-scale flotation cell (capacity 1 litre) was designed, involving a vertically oriented ultrasonic probe (20 kHz, rated at 1.2 kW) and operated in the output power range from 1 to 20% with continuous liquid recirculation. Particle suspension was achieved by the combined action of recirculation and ultrasonic pulses. Interactions of coarse size glass ballotini particles (D32 = 314 μm) with bubbles (< 1 mm diameter) in the presence of a surfactant were studied, using high-speed imaging. Application of an ultrasonic pulse in the aqueous medium resulted in the generation of numerous microbubbles which increased with increasing input power and duration of the ultrasonic pulse time. Such periodic pulses introduced at a high level of turbulence in the pulp phase facilitated adequate bubble-particle contacts. Microbubbles played a key role in forming particle clusters which were observed to be floatable even in the absence of any carrier bubbles. When carrier bubbles were introduced, some of these particle clusters attached to the bubble surface and conveniently floated. It was noted that a favourable state of bubble-particle interaction was achievable to produce stable bubble-particles aggregates by suitably controlling the input power and period of the applied ultrasonic pulse. Keywords: Flotation, bubble-particle interactions, collision, attachment, detachment, ultrasonic pulse

Jan 1, 2020

By N. Madani, S. Abulkhair

In multivariate geostatistics, it is common to have different types of complexities between variables of interest. In this context, an inequality constraint is an example of complex bivariate relationships. Unfortunately, traditional co-kriging and co-simulation algorithms cannot reproduce this type of bivariate complexity, leading to the overestimation of disturbing elements. This paper proposes a new algorithm based on a hierarchical sequential Gaussian co-simulation framework, integrated with inverse transform sampling, to model inequality constraints between variables. First, the proposed methodology's validity was evaluated by applying it to a real case study from an iron deposit, with an inequality constraint between iron and aluminum oxide. Then the simulated results were compared with a conventional hierarchical co-simulation algorithm to investigate the effect of inverse transform sampling on the quality of the co-simulation. The results showed that the proposed algorithm can reproduce an inequality constraint between variables.

Sep 1, 2021

Book Review Gold Metallurgy in South Africa, edited by R. J. Adamson and published by the Chamber of Mines of South Africa, Johannesburg, 1972. The metallurgical processes used for the recovery of gold from Witwatersrand ores were first described in A Text Book of Rand Metallurgical Practice, published in 1912 and subsequently revised in 1926. This was followed by Gold M etall1trgy on the Witwatersrand by A. King in 1949. New Publications Elements of Practical Coalmining, S. M. Cassidy (editor), New York, Society of Mining Engineers of AIME, 1973, $16.50. Future Enerey Outlook, J. A. Pederson (editor), Colorado School of Mines Quarterly, vol. 68, no. 2, April 1973, $6.00. Guide To The Preparation Of Papers For Publication In The Journal Of The South African Institute Of Mining And Metallurgy The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the .Journal.

1. Book review Steels- microstructure and properties, by R. W. K. Honeycombe. London, Edward Arnold, 1981. 244 pp. Rl9,90. (Reviewer: P. T. Wedepohl) 2. New books Decision making in continuous steel casting, by Mark A. Vonderembse. New York, Bowker Publishing Co., 1981. U8 pp. Handbook on continuous casting, by E. Herrmann&apos; Diisseldorf, Aluminium-Verlag GmbH, 1980. 742 pp. Cloth DM 1250, leather DM 1500. Pore structure analysis from a nitrogen adsorption study of porous materials using a volumetric method. User&apos;s guide to the FORTRAN programs: PORESl and PORES2, by E. G. K. Woods. Pretoria, CERGCSIR (P.O. Box 395, Pretoria 0001), May 1981. Oil and gas from coal, by Dick Olliver. London, Financial Times (10 Cannon Street, London EC4P 4BY), 1980. £120. The seventies: a review, the eighties, a preview, by W. Hibbard (editor). Oxford, Pergamon, 1981. 120 pp. £12.50. Computers in materials technology, by T. Ericsson editor). Oxford, Pergamon, 1981. 230 pp. £14.50.

Jan 1, 1981

By R. J. Davidson

The mechanism of gold adsorption on activated charcoal by R. J. DAVIDSON: M.Se., Ph.D. (Rhodes) (Visitor) The adsorption of gold onto activated charcoal is most dependent on the concentration and character of the &apos;spectator&apos; cations present in the adsorption medium. In the presence of calcium ions, gold is adsorbed as the calcium aurocyanide complex. The degree to which the aurocyanide complexes are adsorbed follows the series Ca> Mt:> H> Li> Na> K, calcium aurocyanide being the most stable complex and potassium aurocyanide the least firmly bound. If a loaded charcoal, where the gold is present as the calcium complex, is treated initially with either sodium carbonate or potassium carbonate solutions, the gold can subsequently be eluted from the charcoal with hot deionized water as either the sodium or the potassium complex respectively. The elution of gold with deionized water appears to be most attractive practically and economically, and has several potential applications in the recovery of gold from dilute solutions.

Jan 10, 1974

By K. R. Vost

Variation in air temperature in a cross-section of an underground airway by K. R. VOST, B.Sc. (Glas.), M.Sc. (N.S.W.) (Visitor) Measurements of air temperatures in underground airways are normally made at only one point in a cross-section, and the air tem peratures at other points in the cross-section are assumed not to differ significantly from this. This paper discusses measurements made at a number of points in fifty crosssections in airways with different air velocities and wetness of floor. These measurements show that significant variations of air temperature can occur in a given cross-section at a given time. The effects of such variations on the accuracy of measurement of rises in air temperature as air passes along an airway are discussed. The importance of considering experimental error in the measured rises in air temperature when attempting to validate theoretical and empirical methods of predicting such rises is also discussed.

Jan 7, 1976