Search Documents

By E. Van Der Lingen

Within the context of the overall gold market industrial demand plays an important role. Industrial demand for gold was 430 tonnes in 2008, approximately 12% of total end-user consumption. The dominant consuming industry in this market for gold remains the electronics sector, consuming an estimated 300 tonnes, primarily through the use of gold bonding wire for computer chips and plated contacts and connectors. Substantial demand also derives from dental applications, with other smaller industrial markets and decorative uses of the metal (non-jewellery) constituting the balance. In each market gold faces tough competition from alternative lower cost materials, such as silver and copper (electronics) and ceramics (dental). As well as the obvious benefits to the gold market resulting from this constant physical demand, there are an umber of additional positive factors concerning the use of gold in industrial applications: ?Price inelasticity: demand for gold from the major consuming industries has so far proven to be relatively robust in the face of significant increases in gold price. ??Stickiness?: the gold consumed by industrial uses tends not to return easily to the market (i.e. the demand is ?sticky?) because it is highly dispersed. ?Image: the beneficial environmental and medical applications of gold (e.g. gold used in the treatment of prostate cancer and in purification of contaminated water) are helpful to the positive image of gold. ?Added-value: new industrial uses for gold can create substantial added value in the supply chain, particularly in gold producing countries.

Jan 1, 2009

By G. A. Slabbert

The paper describes work undertaken to identify the influence of the matrix structure on the metal dusting rate of stainless steel alloys. Specifically, the difference in metal dusting rate between austenitic and ferritic stainless steels of similar chromium contents was investigated. The alloys were exposed to metal dusting conditions and their performance compared by weight loss, optical microscopy, scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and Raman spectroscopy. The specific gas mixture used for all the tests were 18.9% CO-79.1% H2-2% H2O at 650°C. For austenitic stainless steels, Types 304, 321, 316, and 316Ti were compared to two ferritic grades, namely Types 430 and 441. The resistance of the ferritic grades was found to be significantly better than that of the austenitic grades. This was attributed to greater permeability of chromium through the matrix structure to maintain the protective oxide scale. The results will be used in the development of novel alloys to combat metal dusting.

Jan 1, 2013

By S. Kahraman

The prediction of rock properties from indirect testing methods is important, particularly for preliminary investigations since indirect tests are easier and cheaper than the direct tests. In this study, we investigate the predictability of the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of rocks from the indentation hardness index (IHI) obtained using point load apparatus. Forty-six different rock types, 14 of which were igneous, 15 were metamorphic, and 17 were sedimentary were tested in the laboratory. The UCS and BTS values were correlated with the corresponding IHI values and the results were statistically analysed. The influence of rock classes on the relationships was also investigated. A strong correlation between UCS and IHI was found for all data. The correlation between BTS and IHI is not as strong as the correlation between UCS and IHI. However, it is in the acceptable limits. When the regression analyses were repeated for igneous, metamorphic, and sedimentary rocks, the correlation coefficients were generally increased. The results show the UCS and BTS can be estimated from IHI. In addition, the effect of rock classes on the relationships between IHI and both UCS and BTS is important.

Jan 1, 2012

By F. P. Greyling

The aspect of sustainability of ferroalloy processes has long been a serious matter for consideration in many of the world?s industrialized countries. A number of countries can be named where ferroalloy plants that were once flourishing, have all but disappeared. One of the most important factors playing a role in this type of occurrence is the cost and availability of quality raw materials. Given that all natural resources will be depleted with time, users are compelled to develop new processes that are sustainable in the changing environment. The DC arc smelting furnace is one such process that has proved itself, and has gained increasing popularity over the past two decades. This process, amongst other benefits, directly addresses the use of more readily available and more affordable raw materials in ferroalloy production. Since early in the new millennium, GLPS has been involved in various studies for different clients of furnaces for the production of ferroalloys. Two of these recent studies have culminated in the design, construction and commissioning of DC arc furnaces for the production of ferrochrome. One of these furnaces is a 10 MW unit at Mogale Alloys, and the other a 60 MW unit at the Middelburg plant of Samancor Chrome. This paper discusses the approach taken in the design and construction of these two furnaces, which, although varying significantly in size and capacity, are very similar in many other aspects of their design. Keywords Furnace, DC arc, and ferrochrome.

Jan 1, 2010

By A. F. Khan

The CSense advanced process control (APC) solution?s main objective was to improve the stability of the pH in the first stage leach process thereby improving nickel and iron extraction efficiencies and reducing the base metal (BM) content in the platinum group metals (PGM) concentrate. By improving the stability of the control of the pH on the first stage leach it had the corresponding effect of improving the Ni extraction efficiency by 0.5% and the Fe extraction efficiency by 3.3%. The system relieved the operators of many decisions that were virtually impossible to make given the complex, variable and real-time nature of the processes in their charge. On the operational side, the operators understand the APC system and they trust it. Another benefit is the reduction in pH peaks in the autoclave, which can oxidize certain elements whereby they become difficult, if not impossible, to leach. These elements go right through the process and end up contaminating the PGM solids, with the result that the entire batch has to be recycled through a lengthy and costly processing pipeline.

Jan 1, 2009

By Kedikilwe Oageng

Effective perimeter control during drilling and blasting is critical not only to blasting results but also to the overall stability of the pit over its entire life span. A pit where perimeter control is not given enough attention when conducting drilling and blasting operations, often experiences over-break or back break beyond final pit wall limits, and therefore has a relatively high probability of failure. Such a pit also becomes unsafe, sometimes not easily accessible, has increased loading costs due to production of oversize, longer cycle times and often problems are encountered when blasting subsequent benches. All these are undesirable consequences, which have negative cost implications. Specialised blasting techniques such as trim blasting and pre-splitting have over the years proved to be effective perimeter control measures. However, the success of these techniques is directly attributable to the time and effort given to the processes. This paper presents results of a project undertaken to monitor, review and optimize the trim blasting and pre-splitting processes at Orapa Diamond Mine in Botswana. The project was specifically incepted to improve the final wall conditions, which continued to deteriorate due to persistent over-break during blasting. The paper also analyses the results obtained against a benchmark of results taken prior to project implementation. Specific blast design parameters which are critical to blasting results were identified as problem areas after auditing of the pre-implementation drilling and blasting practices. These include drill-hole depth, spacing, splitting factor for pre-splits and timing of trim blasts. The impact of different rock types on the results was also studied, and recommendations were made at different phases of the project and results obtained after implementation analysed until optimum results were achieved.

Jan 1, 2008

By H. J. Le Roux, W. B. Drummond

1. INTRODUCTION We have a moral responsibility towards the world to reduce the harmful deposits we emit into the environment arising from beneficiation technologies. Industry has not willingly spent money to limit these emissions because it affected their profit margin with the end result of emitting harmful elements into the environment. Governments have thus rightly stepped in and enforced systematic reduction of these emissions through legislation. In the past beneficiation of sulphur bearing ores was typically done through hydro-metallurgical concentration, smelting, followed by Sulphur removal by converting processes like the Pierce Smith converter. The latter two processes emitted substantial quantities of Sulphur into the atmosphere. Spiralling costs and legislation have resulted in the quest to develop more efficient and environmentally friendly processes to achieve the same end results. New hydro-metallurgical processes like the ActiVox process has completely eliminated the pyro-metallurgical processes. Kansanshi are also operating a similar process. It however elicits other ground water and spillage pollution hazards and problems of it?s own. Various improvements has also been made to the pyro-metallurgical stages, examples being combined smelting and converting with the Noranda reactor, the Codelco CMT furnace, one step flash smelting/converting or the Mitsubishi continuous smelting, converting and slag cleaning process. The new converting processes are also normally enhanced using oxygen leading to higher SO2 gas strength with only a marginal increase in off-gas volume. These processes have led to better efficiencies and a more controlled environment that reduces pollution, but does not eliminate it completely. The fact that there are still more than 70 existing Pierce Smith converter plants throughout the world that needs to be replaced or upgraded at tremendous capital cost, means that we will have the environmental problems for some time to come. The need thus exists to cost effectively get these existing plants into a state where they meet the new environmental regulations, community and safety requirements. This paper will concentrate on just one aspect of this quest, i.e. reduction/removal of off-gasses emanating from the converting of non ferrous sulphur mattes to achieve higher or specialised grades of refined metals.

Jan 1, 2005

By G. Chitiyo

Prediction of pothole characteristics is a challenging task, confronting production geologists at the platinum mines of the Bushveld Complex. The frequency, distribution, size, shape, severity and relationship (FDS3R) of potholes has a huge impact on mine planning and scheduling, and consequently cost. It is with this in mind that this study was initiated. Quantitative analysis of potholes indicates that pothole size (area covered) can be described by two partly overlapping lognormal distributions. These are referred to as Populations A (smaller) and B (larger). The range of observed pothole sizes conforms to a simple double exponential growth model based on Newton's Cooling Curve. A third size range of very large potholes (Population C) that could not be modelled properly within the proposed growth model is interpreted as to represent a very early phase of aggressive regional thermo-chemical erosion and potholing. In general, potholes are dominantly quasi circular with only a subordinate tendency of elongation. In the UG2, potholes with elongated forms are more prevalent in the size range between 20 and 500 m diameter. In the Merensky Reef elongated potholes are more common in the size range above 50 m in diameter. Although not distinctly visible, elongation of potholes in both the UG2 and the Merensky Reef show a net north/south orientation. Using shapes of pothole rims and floor areas, documented for the UG2 in the Waterval Shaft area, it is demonstrated that the northern, down-dip edges of potholes have steeper dips than the southern, up-dip edges. Spatial distribution studies using a uniform quadrant method suggest that in both the UG2 and the Merensky Reef, the potholes are randomly distributed, with a tendency towards clustering. Clustering appears to be more prevalent in the smaller Population A potholes. Bearing all findings in mind, it is found that the model of thermo-chemical erosion of the cumulus floor by new influxes of superheated magma best explains the observed data. Partial to complete melting of the cumulate floor occurred in three phases. The first represents the emplacement of hot magma. This magma, due to turbulent flow and high chemical and physical potential, aggressively attacks the existing floor (crystal mush on the magma/floor interface). Regional erosion is manifested by large, often coalescing potholes. During the second phase, when the magma emplacement process ceased and cooling in situ started, two distinct periods of pothole formation ensued. The first is related to rapid cooling along the relatively steep part of the Newton Cooling Curve, when Population B potholes nucleated randomly and grew rapidly with concurrent convective overturn and largely laminar flow condition. The second period of cooling occurred on the shallow-dipping part of the Newton Cooling Curve. Population A pothole growth became more subdued and nucleation appears to have been, at least locally, clustered. The final phase of this proposed 'super magma cycle' was introduced when chromitite crystallization and precipitation terminated pothole formation. This was followed sequentially by pyroxene and plagioclase crystallization to form the typical cyclic units of the Critical Zone. No suitable proxy could be found for the prediction of pothole density of potholes associated with the UG2 (likely due to limited spatial data coverage), and these are best predicted by extrapolation. The Merensky Reef slope index, in contrast, provides a proxy for pothole density, enabling prediction with reasonable confidence. This predictive model has been verified using underground information. The findings made during the course of this investigation have, when implemented, significant impact. Successful implementation will not only allow enhanced resource and reserve definition, but also better mine planning and scheduling.

Jan 1, 2008

By E. Keskinkilic

In this study, sulfide-type inclusion morphologies of a Ca-treated hot-rolled wheel steel, Grade-X, were investigated. The specimens taken from the hot-rolled products of Grade-X heats were studied. The size and distribution of elongated sulfide inclusions were examined for the heats of different S levels. Elongated sulfide inclusions were either not observed or rarely encountered when ladle analysis S content was below 50 ppm. The size and relative abundance of sulfide inclusions were reported to increase markedly when the S composition was greater than or equal to 70 ppm and the Ca/S ratio was less than 0.50. The effect of Ti addition (0.010?0.020% Ti) on sulfide-type inclusion morphologies was then investigated for heats having a sulfur content higher than 50 ppm. Addition of Ti was found to have a partial effect on decreasing the size of sulfide-type inclusions under real steelmaking conditions. Keywords Sulfide inclusions, Ca-treatment, titanium.

Jan 1, 2011

The Namakwa Sands heavy mineral deposit is located along the West Coast of South Africa and the mine is a world class producer of high quality zircon, ilmenite and rutile concentrates from essentially unconsolidated marine and aeolian sands of Cainozoic age. The objective of this study was to characterize rutile with respect to distribution, grain size, textures, colour and mineral chemistry within the Namakwa Sands orebody with the aim to explain its overall poor recovery. A representative suite of heavy mineral concentrates from various sections of the orebody and stages in the recovery circuit has been investigated microscopically and by means of SEM-EDS and LA-ICP-MS. The rutile grain size distribution displays a wide range and is directly related to its variable chemistry and consequently density. In placer deposits such as Namakwa Sands, mineral sorting is a function of hydraulic equivalence, and high density grains are smaller than the lighter grains when deposited under similar conditions. Grain size is also a function of sediment maturity, and the highly mature red aeolians and (RAS) component of the deposit has a coarser grain size than the less mature orange feldspathic marine sands (OFS). The above primary characteristics of rutile are responsible for the loss of the coarse-grained fraction during screening and, given the empirically determined relationship that increased substitution elements reduce conductivity, also during electrostatic separation. Provenance studies using geothermometry have shown that the heavy mineral suite has been sourced mainly by the proximal medium-to high-grade Namaqualand Metamorphic Complex. The positive relationship between substitution elements and temperature of formation explains their high concentration in rutile of this deposit. The heterogeneity of rutile, produced by the combination of a high temperature primary source and the typical marine-aeolian placer genesis is deposit specific and unfortunately not conducive to high recovery levels in the current Namakwa Sands beneficiation circuit.

Jan 1, 2010

The Skorpion process comprises three processing steps-atmospheric leaching in sulfuric acid, zinc solvent extraction and electrowinning to produce special high grade zinc. The major mode of impurity transfer was attributed to crud runs in the solvent extraction circuit. Crud may be described as a heterogeneous, partly inorganic, partly organic mass of material which accumulates predominantly at the interface between organic and aqueous solutions. The paper describes the root causes of the crud formation in the solvent extraction circuit and optimization strategies which are being followed to prevent impurity excursions in electrowinning. Keywords: zinc oxide, solvent extraction, crud formation, colloidal silica.

Jan 1, 2007

EMMES Sampling Conference BACKGROUND & INTRODUCTION ?Impala acquires toll material to supplement production from ROM ?Toll material consists of filter cake, slurry and catalysts ?Samples are collected to determine the commercial values of the lots ?Slurry deliveries projected to remain relatively constant at 120tons dry solids per month, whereas filter cake deliveries set to increase five-fold to 800 tons dry solids per month ?Due to projected increase in toll material, new sampling and offloading facility presently under construction at Impala ?Presentation will cover two projects aimed at reducing the uncertainty associated with sampling of toll deliveries ?i.e. slurries and filter cake.

Jan 1, 2005

By H. Rosen

The pump is the heart of most industrial and mining plants, providing the energy to separate valuable minerals from process feed. The actual effect of the pump, both in terms of production costs and overall process efficiency, is often assumed or misunderstood by engineers due to insufficient pump performance data. Pump performance can be understood and corrected, where required, through continuous performance monitoring, leading to dramatic improvements in both pump life cycle costs and system efficiencies. The performance of every pumping application is subject to variation and the main contributing factors are as follows: ?Unavoidable deviations from pump supplier curves ?Pump wear ?Pump curve derating factors for slurry pumping ?System curve variation ?Deviation from basic principles of centrifugal pump operation. These are discussed in detail through case studies and the author?s personal experiences. This paper shows ways to minimize the effect of these variations, thereby reducing performance loss and preventing damage to the pump. The paper discusses the benefits of efficient pump operation, the requirements of pump performance monitoring, and its practical application to pump operation in the slurry and water environments. The cost of remedial actions is explored and compared against the savings in both power and plant reliability, resulting in a reduced life cycle cost of the pump.

Jan 1, 2010

A Seminar to discuss 'Reactivity of Line in Steel Making' was held in the auditorium of Iscor's Headquarters Building in Pretoria on the 5th August, 1971. The Institute organised this Seminar on the occasion of the visit of Dr Obst of the Rheinische Kalkstein Werke GMBH, Wuelfrath, West Germany. The latter is one of the largest lime companies in the world and Dr Obst is in charge of their research laboratory. He and his co-workers have earned a reputation for their research into reactivity of lime in steel making. This work is also of great importance to the steel industry in this country, particularly with the changes which are occurring with the introduction of basic oxygen furnaces. Some 80 persons representing most of the major steel companies attended this Seminar. Dr Obst presented his most interesting paper which he illustrated with projector slides. This paper is printed in full in this journal. This was followed by several contributions and active discussions. The first contribution was made by Dr T. B. Beeton of the Research and Development Department, Iscor. He gave a brief summary of the studies on reactive lime carried out at Iscor since 1968. Their work was particularly related to the selection and definition of the various reactivity tests and the correlation of these with plant results. He demonstrated that the DIN methods, particularly the Din (40°) test, gave the best results and reported that good agreement had been reached between Iscor, Highveld and Northern Lime on future test procedures. Mr B. Lowther of The Northern Lime Company then dealt with problems associated with the production of high reactive lime. The rotary kilns at The Northern Lime plant at Lime Acres are particularly suitable for the production of high-reactive lime, because this type of kiln lends itself to accurate control of temperatures and retention times. Several problems, however, exist. Because of the long haul distances and the deterioration of reactive lime by absorption of CO2 and water, high reactive lime is not suitable for most customers. To constantly be changing kiln conditions to produce relatively small quantities of high-reactive lime, therefore, causes problems. Highveld Steel at present is the only company requiring high-reactive lime and a satisfactory product is now being produced at a cost because kiln capacity is reduced and fuel costs are higher. Dr P. R. Jochens, of the National Institute for Metallurgy then submitted data to show how the reactivity of soft burnt reactive lime deteriorated due to long railage hauls. Detailed sampling of trucks had been carried out leaving the lime works and on receipt at Highveld and it was demonstrated that there was deterioration in the top layers of the truck. This top layer protected the balance of the lime which is still in good condition on arrival at Highveld. Exposure to atmosphere by further handling and storage into the bunkers at Highveld, however, resulted in further severe deterioration in the lime reactivity and the lime when finally fed to the Basic Oxygen Furnace is reduced to one third to one quarter of the original reactivity value. The same deterioration does not occur with normal run of kiln lime, which is burnt harder, but still has a satisfactory reactivity for most purposes. Mr A. A. Hejja of the Department of Metallurgy, Witwatersrand University then made a contribution on the metallurgical aspects of the use of lime of different reactivities in the Basic Oxygen Furnace and the effect on desulphurization efficiencies. He gave a wealth of data on actual tests which had been carried out and came up with the surprising conclusion that the deterioration of high-reactive lime due to transport did not have as serious an effect on the efficiency of desulphurization as one would have expected. The efficiency was good provided high-reactive lime in the first instance had been produced, irrespective of whether it had deteriorated thereafter. Poor efficiency was obtained only when the lime in the first instance was produced in an unreactive form. The temperature rise in the Basic Oxygen Furnace also has a definite effect. If lime is introduced when the temperature is too high, soft burnt reactive lime becomes hard burnt and unreactive before it can dissolve in the slag. Use of ferromanganese slag assists dissolution of lime. There was a great deal of discussion following these contributions. Particular interest was expres8ed in the special lime described by Dr Obst. This consists of a mixture of fine lime which is premixed with fluxes and either briquetted or pelletised. The question of injecting finely ground lime as an alternative was also discussed. Both these systems eliminate the necessity for highly reactive lime. With smaller lime particles, larger surfaces are exposed thereby ensuring more rapid dissolution in the molten slag. The discussions generally were lively and informative and all present derived benefit from learning of the experiences of others. The valuable contribution made by our German visitor, Dr Obst, was particularly appreciated. The instantaneous English-German translation service which was provided, greatly facilitated discussions.

By H. S. Sichel

This study deals with the development of some new theory concerning the bias which will result from the employment of the t-estimator if in fact the underlying distribution of ore values is not lognormal. It is found that the t-estimator is robust as long as the logarithmic variance is small and the shape factors of the transformed distribution are not unduly large. The choice of the threshold parameter [t] for the t-estimator is important, and some hints are given how to estimate it if the sample size is small, as en- countered in borehole valuation problems.

Jan 1, 1987

By D. Pienaar, D. Stanton

This paper provides an overview of possible approaches for structuring the ventilation systems for mines that will become operational within the next decade. Features addressed in the paper include: aspects of airway design and layout in the absence of centralized vertical return shafts, the impact of using diesel-powered trackless equipment in conjunction with conveyor belts in the development and production phases of the project, and the need to balance increasing electrical power costs against the requirement for reduced capital expenditure. The paper provides brief descriptions of the strategies employed in real-life situations and presents an overview of various operational parameters affecting the design of ventilation systems that will be used as ?platforms? for much deeper mines in the future.

Jan 1, 2006

By S. M. Brabyn

The wear in mild steel pipelines used to convey rod-milled waste backfill was determined and then compared with that obtained using a laboratory rig designed to simulate the wear condition in slurry pipelines. The relative importance of corrosion and abrasion was investigated under various conditions of water quality and particle size distribution. The laboratory rig was then used to evaluate other possible materials of construction for backfill pipelines. A preliminary assessment of the economic viability of pipelines made of alternative materials is included.

Jan 1, 1988

By L. Bam, R. Machaka, S. Chikosha, N. S. Muchavi

"Parts manufactured through power metallurgy (PM) typically contain pores that can be detrimental to the final mechanical properties. This paper explores the merits of 3D X-ray computed tomography over traditional microscopy for the characterization of the evolution of porosity in metal injection moulding (MIM) and direct powder rolling (DPR) products. 17-4 PH stainless steel (as-moulded, as-debound and sintered) dog-bone samples produced via MIM and Ti-HDH strips (as-rolled and sintered) produced via DPR and were analysed for porosity. 3D microfocus X-ray tomography (XCT) analysis on specimens from both processes revealed spatial variations in densities and the existence of characteristic moulding and roll compaction defects in agreement with traditional microscopic microstructural analysis. It was concluded that micro-focus XCT scanning can be used to study MIM and DPR parts for the characterization of the amount, position and distribution of porosity and other defects. However, the majority of the sub-micron sized pores could not be clearly resolved even at the highest possible instrument resolution. Higher-resolution scans such as nano-focus XCT could be utilized in order to fully study the porosity in MIM and DPR parts. IntroductionMetal injection moulding (MIM) is a novel process, which combines the advantages of powder metallurgy (PM) and plastic injection moulding. MIM has found widespread applications in the cost-effective production of high-sintered density small parts with complicated shapes and mechanical properties equivalent to those of wrought materials (German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013). There are four basic processing steps involved in MIM, namely; feedstock preparation, injection moulding, debinding and sintering. These steps are discussed in greater detail elsewhere (Machaka, Seerane and Chikwanda, 2014; German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013).Feedstock preparation involves mixing metal powder with a carefully selected composition of polymeric binder materials at a specific temperature. The feedstock is then granulated and injected into a predefined mould die with the desired shape. The part produced during the moulding step is referred to as a ‘green’ component. The green component typically contains no porosity since the spaces between adjacent powder particles are readily filled with the binder materials (German and Bose, 1977; Li, Li and Khalil, 2007). Debinding is the systemic removal of the binder components by chemical, catalytic, or/and thermal means while maintaining the shape of the component. The part produced after the debinding step is referred to as a ‘brown’ component. Debinding is known to be the source of porosity in brown components (Ji et al., 2001; Tsai and Cen, 1995). Finally, the brown debound part is sintered to full or nearfull density (Sotomayor, Varez and Levenfeld, 2010). The sintering step and associated densification closes up the majority of the pores. Sintered MIM parts are typically sintered to high density (95–99%) and retain an irreducible amount of residual porosity (Barriere, Liu and Gelin, 2003; German, 1990)."

Jan 1, 2016

By M. Faure

The experiment with backfill at Harmony was mainly an attempt to improve the ground conditions in a particularly tricky section of the mine. A deslimed tailings system was selected for financial reasons, ease of installation, ease of operation and its low level of mechanization. The design of the system has three aspects: firstly, to define the parameters of the backfill material itself; secondly, to design a reliable plant which could consistently produce the desired material in sufficient quantities; and, thirdly, to design a fill distribution system for maximum reliability in the shaft, minimum pipe line velocity, pressure and cost in the horizontal sections and consistency and reliability at the delivery end. The system was successfully constructed and commissioned in a short space of time at a relatively low cost. It has now reached its full potential, and very encouraging results have been achieved with regard to cost savings, ground conditions, ventilation and accident statistics.

Jan 1, 1988

By K. Koruyan

Although remote sensing technology has been available for many years, it has rarely been used for monitoring mining activity. Recent studies indicate that remote sensing is also a valuable tool for managing and planning certain aspects of the mining operation. In this paper, we examine areal expansion of marble quarries and the affected vegetation over a period of 10 years in the Mugla region in Turkey, using geographic information system (GIS) and remote sensing (RS) techniques. Images captured by ASTER Level 3A01 (3D Ortho Data Set), Landsat 5, and Landsat 7 satellites between 2001 and 2009 were used for the analysis. Changes in the natural vegetation as a function of the production level in the marble quarry were calculated using the normalized difference vegetation index. According to the study results, land cover and natural vegetation decreased by less than 3 per cent and 1 per cent respectively between 2001 and 2009, following an upsurge in mining activity in the region.

Jan 1, 2012