Search Documents

By R. P. King

The flotation behaviour of phoscorite from the Phosphate Development Corporation was measured in a pilot plant, the flotation cells in the plant being varied in configuration so as to operate with or without circulating loads. The ore was floated in a batch cell so that the parameters for a kinetic model could be estimated, and these parameters were then used in a flotation-plant simulator, which is based on the kinetic model, in the prediction of the performance of a pilot flotation plant operating on phoscorite. The simulator predictions compare well with the measured performance of the ore in the pilot plant, but the comparison shows that the kinetic model is not completely adequate for the prediction of performance in continuous flotation plants. The model is weakest in its ability to model the behaviour of the froth phase. The flotation behaviour of the ore could be adequately described when it was assumed that the apatite and gangue each consist of floatable and unfloatable components. The effect of particle size on the specific flotation-rate constant of apatite was found to have a maximum at 85 µm and to fall to zero at 400 µm that for the gangue had a maximum at 50 µm and was zero at 350 µm.

Jan 1, 1978

Caving is the lowest cost underground mining method provided that the draw point spacing, draw point size, and ore-handling facilities are designed to suit the caved material, and that the draw point horizon can be maintained for the life of the draw. In the near future, several open-pit mines that produce more than 50 kt per day will have to examine the feasibility of converting to low-cost, large-scale underground operations. Several other large scale, low-grade underground operations will experience major changes in their mining environments as large dropdowns are implemented These changes demand a more realistic approach to mine planning than in the past, where existing operations have been projected to increased depths with little consideration of the change in mining environment that will occur. As economics force the consideration of underground mining of large, competent ore bodies by low-cost methods, the role of cave mining will have to be defined In the past, caving was generally considered for rockmasses that cave and fragment readily. The ability to define cavability and fragmentation, the availability of large, robust load-haul-dump units, a better understanding of draw-control requirements, improved drilling equipment for secondary blasting, and reliable cost data have shown that competent orebodies with coarse fragmentation can be exploited by cave mining at a much lower cost than by drill-and blast methods.

Jan 1, 1994

By W. Wilmans

Electrokinetic dewatering of kimberlite slime under constant direct curents of 0,5 to 2 A and dewatering under constant applied potentia Is of 16,5 to 46,5 V are considered. The combined efects of electrophoresis and the addition of 8,3 x 10-3 M Mg2+ ions on the one hand, and 1 to 10 p.p.m. of the anionic polyacrylamide flocculant Praestol 2935 on the other, were investigated in a 3-litre Perspex electrophoretic cel. .The electro-osmotic dewatering experiments were conducted in a 3-litre Perspex electro-osmotic cel at various electrode spacings, as well as with a moving anode (top electrode). During electrophoretic dewatering, the zeta potential of the kimberlite particles did not change significantly, whereas the pH and temperature showed marked increases with time. The addition of Praestol 2935 enhanced the setling of the sludge bed owing to the additional effect of flocculation. The addition of electrolyte Mg (CIO4)2 retarded the separation process, partly as a result of gel formation in the slurry. During the electro-osmotic experiments, the rate of dewatering was found to be approximately proportional to the applied constant direct current, and to be independent of the electrode spacing. In general, electro-osmotic dewatering seemed to be more energy-efficient than electrophoretic dewatering.

Jan 1, 1987

Orange Free State Branch Minutes of a General Meeting held at the Welkom Mine Canteen on Wednesday, 21st November, 1973, at 4-.00 p.m. Present Mr E. T. Wilson (Chairman) in the Chair, 15 Fellows and Members, 12 Associates, Graduates, and Students, and 11 Visitors (Total 38). Book review Symposium on Environmental Engineering in Coal Mining The 20 papers presented at the symposium cover some 14 subjects related to environmental engineering in coal mines, such as dust, heat, gas emissions, ventilation, noise, and lighting. Competition for students Each year the Institute offers a prize (or prizes should the entries warrant it) of up to Rl00 for the best paper or dissertation on a topic appropriate to the interests of the Institute. A.8. & T.8. Trust The A.S. & T.S. Trust has been formed with the specific object of establishing a worthwhile source of funds which can be used to further the progress of science and technology in South Africa. Nim reports Report No. 1573 A pilot-plant investigation of a flotation model. Report No. 1597 The role of sulphur in the flotation of sulphide minerals. Report No. 1599 The analysis of silicate rocks and metallurgical slags by X -ray-fluorescence spectrometry. Report No. 1607 The analysis of ion-exchange resins by X-ray- fluorescence spectrometry. Report No. 1617 An electronic differential precision thermometer.

Jan 6, 1974

From its early beginnings, shortly after the Witwatersrand gold rush of 1886, Randfontein Estates was planned as a heavyweight operation. The venture was capitalized by J .B. Robinson to the tune of £2 million at time when syndicates were loath to invest £50000 in ventures in and around the new metropolis, Johannesburg, which had sprung up midway along the Witwatersrand. But by then Robinson was a colossus among his contemporaries. Operating as a loner as he had done on the Kimberley diamond fields, where he created his own individual fortune and commanded the sort of respect which, early in his career, led to his election as Mayor of Kimberley. When news of a third gold discovery in the Transvaal (the first two had been in the Pilgrim's Rest and Barberton areas) reached Kimberley, Robinson's pioneering spirit was further stired and he hastened to the new goldfield to stake his claims before his business adversaries- Rhodes, John X. Meriman, Hans Sauer, and Caldecot-could entrench themselves. Once the new Witwatersrand goldfields had been proclaimed, claimpegging started in earnest. But the question was: where to start? Diamond men al, not one of the financiers had any knowledge of the geology of the gold-bearing formations.

Jan 1, 1989

By Wm. Bleloch

SYNOPSIS The feasibility of rejection of nitrogen from stack gas by recycling of top-gas with cold-blast 95 to 98 per cent oxygen is assessed. It is concluded that nitrogen could be removed to a level below 3 per cent of the stack-gas using recycled cleaned cold top-gas and 95 to 98 per cent oxygen produced by a single-column air separation plant with liquid-air reflux instead of liquid nigroten reflux. The partial pressure of carbon monoxide in the stack-gas could be doubled without top pressure and the deposition of carbon and reduction of iron oxides by the stack gas could be markedly increased. It is concluded that rate of stock descent could be doubled compared with present-day practice and an iron make of 4400 kg/m 2 of hearth area/hour may be attainable with a working volume of 129 m2/m hearth diameter by this method. Oxygen consumption is estimated at possibly 280 m2 (0.4 t)/t iron made and carbon consumption at possibly 280 kg/t iron. Power consumption for oxygen including auxiliaries is estimated at 304 kWH/t 100 per cent oxygen as 95 to 98 per cent gas. The air separation cycle due to Schuftan is discussed in some detail, and the components of a 1 600 metric ton/day separation plant are briefly discussed. The paper is a theoretical essay.

By D. G. Krige

Using a very large number of chip-sample values from a mined-out area of the Hartebeestfontein mine and accepting these as equivalent to borehole values (also areas of 1 km by 1 km as equivalent to 'mines'), the authors apply a series of borehole-valuation procedures to these 'mines', Large undeveloped sections of existing mines are also regarded as the equivalent of such 'mines'. These procedures start with the orthodox arithmetic mean and then introduce additional information in the form of the Iog normal frequency distribution model for Sichel's 't' estimator. Knowledge of the average log-variance within mines leads to the tH estimator. The mean grade of the 'family' of mines to which a new mine belongs is then introduced via regression or elementary kriging. Next, further information on the macro spatial structure of the grade is used, together with the grades of adjacent existing mines in ordinary and simple macro-kriging procedures; finally, via the distribution model, the grade is seen as a function of the logs of the grades and their variances. These are introduced as spatial variables, and both are estimated by macro-Iog normal ordinary and simple kriging procedures with grades and variances from adjacent mines'. Comparisons are also made between macro-kriging on lognormal transformed values versus untransformed values. Conclusions are drawn on the relative importance of the various items of additional information used, on the procedures followed, and on the significance of the advantages gained

Jan 1, 1992

By G. Ferrara

The mathematical framework of a well-established model proposed earlier by the authors for the screening process is briefly recalled. Some numerical methods for the application of the model, concerning numerical solution of the equations and parameter estimation, are indicated. Some applications of the model to improve screening operations, sizing of screen, simulation of screening and of integrated plant operations are discussed, and the computer software to be used for these purposes is described in detail.

Jan 1, 1987

By M. A. de Ruijter

Bracken Gold Mine ceased mining operations during February 1993. The clean-up of the gold plant, which had already commenced in September 1992, was completed in January 1994. The mine had been in production since early in 1962 but, because of a decreasing ore reserve, increasing working costs, and a relatively low gold price, closure had become inevitable. The closure had been under consideration since August 1983, when the first estimate was made regarding the amount of gold that could be recovered from the clean-up operations. Until that stage, it had been accepted that Bracken would conform to the commonly accepted idea that 0.25% of the total gold produced by the plant would be recovered during the clean-up operation. This idea was dispelled when the initial estimates indicated that the gold recovery would vary between 0.049 and 0.095%. The actual figure realized was 0.036%, showing that there is no generalforl1ula for the calculation of the amount of gold to be recovered from such clean-up operations. During the clean-up operation, Bracken became an unexpected contributor to the State's Reconstruction and Development Programme by having al the mine and plant buildings purchased and converted into a community development centre. This shortene4 the time available for the clean-up, and several of the buildings remained intact. However, the foundations and sub-soils had been sampled extensively, and it is considered that no recoverable gold was left behind.

Jan 1, 1996

The block caving mining method is used to mine large orebodies in weak rock types. The layout for block caving requires that a considerable amount of development is carried out on the extraction drives and drawpoints at the bottom of the caving block. The development further weakens the rock mass, and stability problems arise in the extraction drives and extraction pillars. This paper describes the application of three-dimensional boundary element models in analysing alternative extraction level layouts for a block caving mine. The objectives were to establish whether the use of lateral pillars between drawpoints was warranted, and whether the lateral pillars should be offset or not. The stability of the rock mass within the pillars as well as the stability of the extraction drives were taken into account. The results showed that after undercutting, the horizontal and vertical stresses in the extraction level would be reduced. The lateral pillars would significantly improve the stability of the extraction pillars and extraction drives. There would be a minor improvement in stability if the lateral pillars were offset.

Jan 1, 1987

By G. A. Matthrsuis, R. N. Morris

The paper identifies two zones in a Leeds flotation cell. The ratio (13)of the dissipative forces and the interfacial tension force acting on a bubble and a solid particle are shown mathematically to be proportional to the square of the particle diameter for the quiescent zone and inversely proportional to the particle diameter for the turbulent zone. To locate the range of operation, correlations were established for the bubble diameter through photography and bubble counts. 13was found to be fairly constant in the particle size range 38 to 150 ",m, and the level of turbulence unlikely to affect the bubble-particle attachment and hence the beneficiation efficiency. This was verified in a series of flotation runs with a standard Leeds cell and a modified cell of twice the height to increase the capacity of the quiescent zone. A series of tests on the size range 300 to 600 ",m showed that the turbulence level had a marked effect on the cell performance through a relative improvement in the beneficiation efficiency due to the increased height of the cell. To identify the significant variables in the size range 38 to 150 ",m, a factorial design was carried out. Promoter dosage and particle size were found to be significant, aeration rate and impeler speed being insignificant at the 95 per cent confidence level. Multiple regression correlations were established for the recovery of organic material, mineral rejection, and beneficiation efficiency.

Jan 1, 1988

By T. Wennberg

An elevated location of a paste thickener on a ridge close to the disposal area is considered at a Swedish iron ore mine. About 0.7 M tonnes of thickened tailings are planned to be layered as paste in the vicinity of the thickener over several years with pipeline lengths of up to 900 m after about 20 years. In order to clarify the pipeline pumping characteristics of the tailings product for volumetric solids concentration from 40 to 50%, experiments in loop systems with pipeline inner diameters from 0.063 to 0.152 m have been carried out with various types of pumps. The results and comparisons carried out here showed that the performance of centrifugal pumps cannot simply be related to the rheology, but factors related to pump design and build-up tendencies of material within the pump and other particle properties may be of equal importance. During the first years of operation only one thickener underflow pump is required. The reliability and performance for various pump configurations are planned to be investigated systematically in order to meet the most effective long-term solution for paste thickener operation, pipeline distribution and placement in the disposal area as the discharge point advances over the life of the project.

Jan 1, 2007

Scrap printed circuit boards were selectively smelted at 1 200°C to produce a metallic alloy having three phases. These phases were identified as a lead-rich phase, a low tin content alpha bronze phase, and a high tin delta phase. Electrochemical leaching studies on this alloy were done in 1 mol/dm3 sulfuric acid or in 2 mol/dm3 hydrochloric acid (adjusted to an ionic strength of 3 mol/dm3). The lead rich phase was more strongly passivated in sulfate media, and in this medium the high tin content delta bronze was more resistant to corrosion than the lower tin alpha bronze phase. In chloride medium the lead phase and both bronze phases corroded readily, but with current densities about an order of magnitude lower than in sulfate medium (static conditions) for the bronze phases. The high tin delta bronze phase was found to form a passivating layer in sulfate media. A similar layer was not seen in chloride medium. The leaching studies in sulfate medium also showed the existence of an alpha bronze phase of lower tin content in the centres of the alpha phase grains. This phase was quite resistant to leaching in sulfate medium.

Jan 1, 2009

By P V. Savage, T Glück, RCA Minnitt, C Bothma

Manganese Metal Operations ?Manganese Metal Company (MMC), a subsidiary of Samancor BHP Billiton, has two production facilities for electrolytic manganese metal in South Africa and produces a range of about 44 Mn metal products. ?The company is accredited with ISO 9000 and uses Six SigmaTM for continuous improvement. ?The control of the process relies on the effective functioning of approximately 250 different control loops at 50% automation.. ?Approximately 50000 samples are analysed every month. ?There are pyro, hydro and physical unit operations for the production of electrolytic manganese metal flake and value added products ? [ ]

Jan 1, 2005

By I. M. Macleod

An adaptive steady-state on-line optimizing regulator is proposed as an integrated approach to the control of autogenous run-of-mine milling circuits. This optimizing regulator continuously estimates an internal model of the controlled process, and, based on this, determines mill fresh solids feed rate, mill water flow rate and sump water addition flow rate such that a circuit performance objective is optimized. The dual -requirement of controlling both the mill pulp load and the load of particles of grinding media size is thus directly and simultaneously addressed. The concept and theory underlying the operation of the adaptive optimizing regulator are discussed.

Jan 1, 1987

By K. N. Karparov

The stress state on two slope profiles overlying an inclined surface with layer inclination of 50 and 150 are investigated. It is demonstrated that the induced stress state in an imbedded weak layer, exposed at the base of the slope, forms a zone of induced tensile vertical and horizontal stresses, which can lead to failure. The zone length depends on the slope angle and the angle of the inclined layers. L’état des contraintes sur deux profils en pente en superposition sur une surface inclinée avec une inclinaison de couche de 5o et 15o est étudié. L’étude présente démontre que l’état induit des contraintes dans une couche faible insérée, exposée au bas de la pente, forme une zone de contraintes de traction induites horizontales et verticales, qui peut amener à la rupture. La longueur de la zone dépend de l’angle de la pente et l’angle des couches inclinées. Die Druckvorkommnisse zweier Hangprofile auf einer schrägen Fläche mit einer Schichtneigung von 5º und 15º wurden untersucht. Es zeigte sich, dass die induzierten Druckvorkommnisse in einer eingebetteten schwachen Schicht, die am Hangfuße offen liegt, einen Gürtel induzierter vertikaler und horizontaler Zugkräfte bildet, die zum Zusammenbruch führen können. Die Gürtellänge ist von der Neigung des Hanges und der Neigung der schrägen Schichten abhängig.

Jan 1, 2003

By Stephen Hughes

Ausmelt Top Submerged Lancing (TSL) Technology has gained widespread commercial acceptance in the lead and zinc industries, as an efficient and highly flexible pyrometallurgical reactor with accompanying excellent environmental performance. For the processing of lead and zinc bearing feed materials twenty one (21) Ausmelt furnaces are now in operation, under design or under construction. With recent increases in the value of both lead and zinc and an ever increasing focus on the sustainable use of resources, interest in the processing of secondary feed material sources as well as metal containing residues has substantially increased. Ausmelt Technology has proven to be well suited to the economic recovery of values from such sources. This has for example culminated in Ausmelt?s commitment to the Whyalla Zinc project as the owner/operator of a facility for the treatment of zinc bearing secondary feeds. This paper describes Ausmelt?s recent developments in the fields of lead and zinc processing, as well as further investigations into new processing areas, including the direct smelting of zinc concentrates. Ausmelt?s TSL Technology can now be regarded as Best Available Technology (BAT) for metal production.

Jan 1, 2008

By S. Carter

this paper describes an innovation in computer software that permits mining professionals to collaborate on exploration and mining projects regardless of geographic location. Growth of mining companies through merger and acquisition has created a greater need for mining professionals to collaborate, especially as projects and project participants are becoming geographically remote. Surpac NetVision, the name given to this new collaboration technology, satisfies this need by deploying interactive 3D graphics sessions across computer networks. It achieves this by using common web browser technology as the deployment medium. A plug-in architecture that supports diverse file formats permits transparent read and write of foreign data to further enhance the collaboration process. Surpac NetVision supports any number of connections from web browsers on remote computers using existing networks. Software components required to enable the collaboration session are deployed to the remote computer as required and cached for future sessions. The collaboration session at each computer is characterized by a fully functional replica of the user interface for Surpac NetVision from which any function can be executed by any client, at the owners discretion. All geometry and display attributes deployed to remote clients to render 3Dgraphics are highly compressed to reduce bandwidth requirements. The key benefits of this collaboration technology is improved communication in regard to exploration and mining projects leading to: •More informed decision making •Improved deployment of project objectives and plans beyond the technical planning group to project management and operations staff •Improved technical support for software users. Keywords: 3D graphics, project collaboration, interactive graphics, internet 3D graphics, mining software

Jan 1, 2003

By G. W. Holl, E. G. Fairon

A review of some aspects of shaft design by G. W. HOLL, Pr. Eng., Associate of the Mine Managers Association of South Africa (Fellow)- and E. G. FAIRON, Pr. Eng., F.S.A.I.E.E., M.I. Cert. M.E.E., M.I.Mech. E., (Visitor) The reasons for the choice of vertical shafts in preference to inclined shafts of comparable capacity are set out, and the conclusion that the former are superior in virtually all circumstances is substantiated. The shapes of vertical shafts sunk during the past sixty years are recorded, and the shapes of those sunk during the past decade are analysed. From this analysis it is clear that circular and elliptical (and quasi-elliptical) shafts are the shafts of the future and that the rectangular shape will conceivably become obsolete. The determination of the size of shaft is discussed and it is forecast that shafts of a diameter of 13 metres and over will probably be sunk without difficulty in the years to come. The depth of the shaft is determined intrinsically by the Mines and Works Regulations applicable to factors pf safety of winding ropes and the design of the winding system. The Blair winder is the most suitable winder for hoisting rock, men, and material from a depth of, say, 3000 metres on an economic basis. Tertiary shafts will, therefore, be unnecessary in future deep-level mining projects at the limit of depth now envisaged. A few other factors relating to shaft design are described.

By Y. Lizotte

This paper describes the design and implementation of the dispatching system at LAB Chrysotile Inc.'s Black Lake Mine Operation, Quebec, Canada. The initial system uses a computer in a passive role, to record and display information in ongoing operations. Simulation studies were undertaken at McGill University to assess various heuristic dispatching rules which can be program- med and inserted into the dispatching system. The computer can then suggest to the operator where a truck should be sent to maximize productivity or improve fleet efficiency. The study stresses the importance of considering the effects of implementing computerized systems on those individuals who must use these systems in their daily work. The roles of individuals from the industry and the university in this joint project are also highlighted.

Jan 1, 1987