Search Documents

By Donald B. Larson, Milton Finger

The use of explosives in deep rock mining carries conventional blasting technology into a relatively new and unexplored realm. Although bill ions of pounds of explosives are used fairly routinely in mining, quarrying, and construction, almost all of these uses are surface blasting. Most of the in sib processes that are proposed for recovery of mineral or energy resources require the creation of high permeability to provide well defined flow paths in the resource bed. At present there is very little information on the fracturing produced by explosives deep in the earth, and the technology for using explosives in deep rock mining is just evolving. A qualitative understanding of the applicable mechanisms in deep rock fracture leads to some key parameters in the selection of explosives for deep rock mining. The selection and characterization process involves a careful analysis of the field environment and the establishment of tests to determine candidate explosives response to planned and accidental stimuli. The details of this selection and characterization process are given for a few candidate explosives. The use of explosives in deep rock mining must be considered as one of the possible tools for recovery of yet untrapped energy and mineral resources. A basic understanding of explosive deep rock fracture will allow optimum selection of explosive processes or other more appropriate methods for recovery of energy or minerals from a particular resource area. The results of some experimental studies are discussed.

Jan 1, 1977

By J. Stachurski, N. A. Abdel-Khalek

The objective of this investigation was to compare the results of countercurrent, column cell flotation vs. conventional (mechanical) cell flotation for the cleaning of a sulfur ore (-0.5 mm, 27.43% S) and its discrete size fractions. The tests were carried out using diesel oil as a collector and alcohol as a frother. Generally, column flotation produced concentrates of higher grade. For example, column cell flotation produced a nonwashed concentrate of 65.3% S with a recovery of 84.1%. However, conventional cell flotation produced a rougher concentrate of lower grade (57.0% S) and higher recovery (92.5%). At a superficial-wash water velocity of 0.265 cm/sec, the column product grade increased to 76.4% S, with a slightly lower recovery (80.3%). However, a concentrate with a similar recovery but a lower grade (74% S) than that of the washed product was obtained after three cleaning stages with the conventional cell. The column gave superior results for the flotation of fine and ultrafine particles.

Jan 1, 1994

By S. K. Kawatra

For efficient control of particle size in a wet grinding circuit, three alternative methods for monitoring pro- duct particle size are available. These methods are based on: 1. Ultrasonic wave absorption. 2. Low-angle forward scattering of a laser beam. 3. Inferential sizing techniques. The relative advantages and disadvantages of each technique are discussed. A particle size monitor can be used on a single grinding line to control the product particle size. To minimize the number of particle size monitors at an operation consisting of many similar grinding lines, a portable multi-stream on-line analyzer can be used. The paper outlines the design and the operational characteristics of the portable multi-stream online analyzer.

Jan 1, 1979

By John A. Ames

Limestone for portland cement must be beneficiated to produce uniform raw material for the kiln. Careful quarrying and selective recovery are factors in this process, but the chief aspects of beneficiation are "in plant" processes, such as crushing and screening, washing, grinding, flotation, and heavy-media separation. Numerous technical and economic problems exist. Detailed studies of the limestone deposit and the stone itself are required for intelligent beneficiation. As used in this paper, beneficiation is defined as the improving of limestone composition so as to produce an economically usable raw material A limestone deposit is defined as a mass of limestone which can be recovered, by quarrying or mining, for sale or for use in a commercially profitable operation. The stone may require elaborate processing, or it may qualify with little or none. Obviously, the "commercially profitable" qualification may change as the economy changes. Potentially commercial deposits may be of much better quality than actually developed deposits, and yet may be denied development for various economic reasons.

Jan 1, 1966

By Allen V. Reicks, Thomas J. Rudolphi

Computerization has allowed practical design of complicated and optimized belt conveyors for bulk materials from prediction of belt tensions around the belt circuit for a wide range of belt loadings and conveyance paths. These design methods are based on a knowledge of component operating characteristics and sources of tension change. As compared to generalized 'f' methods, CEMA's historical Kx and Ky has provided nonlinear and more specific predictions of belt tension as affected by various components and operating conditions. These empirical values were developed in a different age and generalizations made in their development are now a constraint to additional conveyor improvements. This paper discusses the potential from improved and standardized ‘friction’ predictions and presents the results of sensitivity evaluations as affected by calculation method

Jan 1, 2004

By Y. C. Kim

To generate a most profitable, ultimate pit limit is generally the first step in mine design. This paper presents a new graph theory oriented, optimum ultimate pit limit design algorithm which will maximize the total undiscounted net profit. This algorithm performs much better than the well known Lerchs-Grossmann algorithm, in terms of the reduction in computation time and computer memory requirements. This algorithm operates on many directed trees in a graph, where each vertex in a tree represents a block in the mine model. The formation of each directed tree is based more on the ore-waste support concept than the geometry constraints alone. The general procedures of the algorithm, programming considerations and two case study results are discussed in the paper.

Jan 1, 1992

By Jaime E. Sepúlveda

Semiautogenous grinding (SAG) operators have been realizing the very significant impact of fresh feed particle size distribution on the mill grinding capacity. In actual practice, this impact may be quite difficult to assess because of the natural process variability that may also involve- concurrently other critical factors such as ore hardness. Recognizing the limitations of the empirical approach, the current publication proposes the use of mathematical models and simulators to explore and assess the net effect of feed particle size only, independent of any other factors. The simulation analysis here reported provides a basis to claim that the size distribution of the particles being ground (simply characterized by a % - 2" or similar measurement) is one of the most relevant controlling variables of the overall mill performance, regardless of the SAG circuit configuration.

Jan 1, 2005

By R. A. Pindred, M. P. Lam

Cyanide is a conventional lixiviant for gold extraction but its' toxicity is a major concern for the environmentalist. There are many alternative non-cyanide lixiviants, such as thiourea, thiosulphate, chlorine and hypochlorite etc., which may reduce environmental sensitivity. This paper will discuss the leaching characteristics of gold in hypochlorite leaching solutions. The dissolution of gold in a hypochlorite solution not only depends on the concentration of the hypochlorite but also on other variables, such as hydrochloric acid, sodium chloride and temperature. The dissolution rate of gold in hypochlorite solution is much faster than other lixiviants. Due to the interference of impurities, gold extraction from an ore under ambient conditions requires large quantities of reagents. However, refractory gold ores may be successfully pressure oxidized in an autoclave at reasonably low reagent levels. Gold extraction to the pressure oxidation leach solution is rapid and complete in one stage, thus eliminating the need for further cyanidation.

Jan 1, 1990

By Kenneth R. Miller

Surface mine equipment operators in the Campbell County region of Wyoming's Powder River Basin have found new ways of solving old problems. Technology, experience, competitive pressures and an increasing grasp of economies of scale have driven mine operators, equipment manufacturers and suppliers to specialization of applications. In economic terms, today's coal price of $4.95/t ($4.50/st) equates to $2.53/t ($2.30/st) in 1980 terms - an incomprehensible value at that time. This article describes some examples of change and adaptation made by Powder River Basin coal operators in overburden stripping equipment and techniques. It focuses on the evolution of the design and use draglines, shovels, trucks, scrapers and dozers.

Jan 1, 1998

By Pradip

The selection, testing, and commercial utilization of flotation reagents is best carried out in stages through microflotation tests on pure minerals and their synthetic mixtures followed by bench-scale batch flotation tests on the ore. A systematic approach to quantitatively evaluate different reagents, in particular, through the analysis of batch flotation data, has been presented in this paper. It is recommended that the reagents are compared both in terms of their performance with respect to the recovery-time as well as the recovery-grade plots. While the former describes the kinetic aspects of reagent interaction, the latter is a measure of its selectivity for a particular separation problem.

Jan 1, 1987

By Siegfried Zell

Preface Pipe heading is a customary and proven technology for the underground installation of all types of piping. In over 90 % of all cases, straight pipe sections are used between shaft constructions since, e.g. this follows roadways or it is necessary from the operational aspect due to pipe control methods, e.g. to use a remote control pipe sensor or comparable control devices within sight from shaft to shaft. Frequently, a straight pipeline is impossible, and is replaced by a more or less spatial alignment due to surface conditions, structures in the ground or foundations. This situation applied for the construction of the Nebensammler Neuland (intercepting sewer) in Hamburg-Neuland for sections IV and V. The following paper is not intended as a description of the complete project. It deals mainly with the special features of this pipe heading, with what I believe to be its somewhat unusual route. The task The building authority design issued by the Main Department for Urban Sewerage of the Free and Hanseatic City of Hamburg consisted of the construction of the collector by a pipe heading using NW 1300 pipes in 2 heading sections. One short straight and one long

Jan 1, 1989

By Leszek W. Lunarzewski, Adam L. Lunarzewski, Raymond C. Pilcher

The Floorgas and Roofgas simulation programs are used to identify strata relaxation zones and their boundaries, to assess active gas sources from coal seams and gas¬bearing rocks and to determine relevant gassiness prediction coefficients for any local longwall. The paper shows that by use of the print-outs from the Floorgas and Roofgas programs the following benefits are achievable: • identification of the shear and gas discharge zone positions in the floor, strata relaxation angles and various gas discharge zone positions in the roof, which are both relevant to local geological and mining conditions • optimisation of cross-measure drainage hole length, location, number and angle of inclination calculation and definition of gas make prediction coefficients such as the release ratio from adjacent coal seams, specific gas emission during longwall extraction and the relationships between gas make, longwall width and coal production levels.

Jan 1, 1995

By M. M. Rajkovich, L. Adams, J. J. Zaluski, S. Gardner

In 1998, a group called Kentuckians for the Commonwealth filed an Administrative Petition with the Kentucky Natural Resources and Environmental Protection Cabinet to designate 8,903± hm2 (22,000± acres) on Black Mountain, which contains the state's highest point, as unsuitable for mining. A fast track legislative process was triggered that could have "taken" 91 Mt (100 million st) of coal reserves or, in the alternative, imposed severe restrictions on mining. Even with all parties represented by reasonable individuals, this process can be extremely cumbersome and expensive. The legal and technical preparation for this unusual hearing process as well as issues and strategies of the negotiated resolution are reviewed

Jan 1, 2002

By Noel N. Moebs, John L. Ellenberger

Geologic structures in mine roof rock contribute to many roof falls in Appalachian coal mines. These structures include paleochannels, scours, pinch-outs, slickensides, clay veins, and cravasse splays consisting of thinly interlaminated sandstone and shale. These structures often can be identified during, and sometimes before, development and mine projections can be revised to reduce the adverse effects of discontinuities in roof structure. Large areas of roof consisting of laminated sandstones or incompetent strata generally can be delineated from exploratory drill-hole data and the need for supplementary support can be anticipated. Because an accurate description of roof geology also provides some indication of optimum length and type of roof bolts that should be installed, this Bureau of Mines paper describes the hazardous roof structures most commonly encountered in the Appalachian coal region.

Jan 1, 1982

By K. N. Han

The leaching behavior of palladium in ammoniacal solutions was investigated by using the rotating-disk technique in an autoclave. The study included the effects of rotation speed, temperature, oxygen pressure, composition of ammoniacal solutions and catalysts on the overall leaching rate. The dissolution of palladium in ammoniacal solutions was discussed in terms of the thermodynamics and a kinetic model. Even though the Eh-pH diagram suggests that palladium metal can dissolve in ammoniacal solutions at room temperature, it was found that the dissolution was very slow at temperatures below 100 °C but was significantly improved at higher temperatures. It was also found that the rotating speed of the palladium disk had no effect on the leaching rate. The apparent activation energy was found to he 69.7 kJ/mole. Based on the results obtained, it was concluded that the dissolution of palladium is controlled by chemical reaction.

Jan 1, 1999

By Richard L. Ranich, Frank F. Aplan, J. B. Hiskey, Robert S. Thompson, B. J. Scheiner

Acidic waters typified by acid mine drainage, copper dump leach solutions and steel pickle liquors will typically contain SO4-2 and cations such as Fe+3, AI+3 and for the pickle liquors, sometimes Cr+3. These acidic waters will often react with limestone, present naturally or introduced for purposes of solution neutralization, to form reaction - inhibiting coatings of gypsum and gelatinous, metal hydroxide precipi¬tates. The coating thickness, as a function of pH, was quantified for both reactive (calcite, limestone) and non-reactive (quartz, barite, fluorite) minerals, and the data were related to the hydroxy species diagrams and to solution turbidity measurements. Coatings were found on the reactive minerals at a lower bulk solution pH than on the non-reactive minerals.

Jan 1, 1993

By L. Xu, R. Bhaskar

While a NIOSH accepted procedure exists for determination of quartz in the respirable dust samples from coal mines, no specific procedure has been defined for quartz determination in bulk samples. In this study, the effect of particle size on the estimation of quartz using the infrared technique was evaluated. Several laboratory tests were performed to determine the dependence of the infrared absorbance peak height on the different sizes of quartz particles. The significant dependence observed between quartz particle size and the measured peak height indicates the potential for erroneous interpretation of the quartz in bulk samples depending on how the samples are prepared. A procedure to reduce the effect of size in the determination of the quartz content is suggested.

Jan 1, 1994

By Donald E. Hulse

Selection of a block size for a computerized 3 dimensional ore body model is an exercise in compromises. Larger blocks decrease the use of computer resources and decrease the variance of the block estimates. Smaller blocks increase the resolution of the model and the selectivity which can be used in the planning, but increase the variance of estimates in the individual blocks. A common rule is that blocks can be as small as one fourth the average sample spacing, however this ignores the interrelationship between the block size, the sample spacing, and the variogram model. This paper will explore this relationship Kriging estimation variance will be used as a comparative measure of estimate quality. Graphical techniques will be used to show that there is a point where smaller block sizes cease to contribute to the resolution of the model. A method of evaluating the consequences of block size decisions will be examined.

Jan 1, 1992

By S. L. Huang, J. D. Rockaway, N. B. Aughenbaugh

Shale has long been recognized for its tendency to swell when exposed to the atmosphere. Interaction of moisture with exposed shale strata can cause serious ground stabi1ity problems, since the initial strength of a shale is reduced if the material is sensitive to moisture variations. In this paper, the authors present a classification system to estimate the response of swelling generated within shales. This characterization of the swelling potential is based upon plasticity, susceptibility to moisture, mineralogical constituents of clay size particles, and fabric. Use of this classification system in conjunction with other existing rock properties tests will provide data for more rational engineering design.

Jan 1, 1986

By Jin Kim, Jerry C. Tien

Water is still the most economical and popular means of controlling dust underground. It is a process that captures dust by bringing water droplets into intimate contact with coal particles. Wetting agents, also known as surfactants, can be added to greatly facilitate such a process since they tend to reduce the interfacial tension between the coal particles (usually hydrophobic) and the liquid. The surfactants used in the study were first chosen on the basis of their HLB (Hydrophile-Lipophile Balance) value, and later tested in order to select the right type and amount of surfactants to give the best performance. Both static and dynamic tests were later conducted using different types of surfactants to examine their respective wetting effectiveness on coal particles. Experimental results show close correlation with the theoretically calculated collection efficiency that is based on a horizontal tunnel and a solid-cone water spray.

Jan 1, 1993