Search Documents

By G. Mbuyi Kamba

Literature is rather abundant on the topic of steady-state network analysis programs. Many versions exist, some of them have real extended facilities such as full graphical manipulation, fire simulation in motion, etc. These programs are certainly of great help to any ventilation planning and often assist the ventilation engineer in his operational decision making. However, what ever the efficiency of the calculation algorithms might be, their weak point still is the overall validity of the model. This numerical model, apart from maybe the questionable application of some physical laws, depends directly on the quality of the data used to identify its most influencing parameters such as the passive (resistance) or active (fan) characteristic of each of the branches in the network. Considering the non-linear character of the problem and the great number of variables involved, finding the closest numerical model of a real mine ventilation network is without any doubt a very difficult problem. This problem, often referred to as the parameter adjustment problem, is in almost every practical case solved on an experimental and "feeling" basis. Only a few papers put forward a mathematical solution based on a least square approach as the best fit criterion. The aim of this paper is to examine the possibility to apply the well-known simplex method to this problem. The performance of this method and its capability to reach the global optimum which corresponds to the best fit is discussed and compared to that of other methods.

Jan 1, 1995

By John A. Dearinger, Fred D. Wright, Robert C. Howell

INTRODUCTION The rock mechanics study of the shortwall mining system at Beth-Elkhorn corporation's Hendrix No. 22 Mine is being conducted under contract with the U.S. Bureau of Mines. The objective of the study is to obtain data on surface subsidence over a portion of the mined area, strata subsidence in the mined area, and underground stress changes and displacements in and near natural support elements of the mining system. This study is currently in progress, and only a portion of the results are being presented at this time. The Hendrix No. 22 Mine is located in the moderately rough mountainous terrain of Letcher County in eastern Kentucky. The nearest mine workings to the shortwall area are approximately 1,900 feet distant. The depth of cover over the mined shortwall area varies from 770 feet at Panel 1 to 170 feet at Panel 5 (Figure 1). The strata in the shortwall area is summarized in the three core logs shown in Figure 2. Hole no. 2 is located in approximately the center of the mined shortwall area (Panel 3, Line C, Figure 1). The coal seam in the shortwall area is approximately 4 feet thick and horizontal, although one major ‘roll’ intersects all panels.

Jan 1, 1977

By G. D. Criswell, F. Palkovits, J. M. Johnson

A paste technology investigation was completed for non-pozzolanic fly ash from Units 3 & 4 of PPL Montana’s Colstrip Steam Electric Station. The purpose was to assess the feasibility of converting from dilute slurry deposition of ash products to a system using thickened or paste ash to reduce excess water storage in the impoundment, reduce seepage losses, and increase storage efficiency. The investigation included laboratory and field testing to characterize the rheological, geotechnical and dewatering properties of the ash products, an assessment of potential seepage reductions and an evaluation of potential for increased ash storage capacity by modifying impoundment operating procedures. The studies concluded that the conversion project was feasible, cost effective, and permittable. Critical facilities for the conversion project are currently under construction.

Jan 1, 2004

By I. Iwasaki, K. A. Smith, X. Cheng

The reaction mechanism for the cathodic decomposition of pyrrhotite in deoxygenated solutions at natural, near neutral pH levels was studied using potential and cyclic voltammetric measurements. Reaction products on the pyrrhotite surfaces were examined by Auger Electron Spectroscopy (AES), by X-ray photoelectron spectroscopy (XPS) and by analyzing the voltammograms for the electron balance of the reactions. Surface properties of the pyrrhotite/solution interface were characterized using an ac impedance technique. The parameters of an equivalent circuit were determined by the nonlinear least-squares fit (NLLSF) technique. The effect of cathodic polarization on floatability was investigated by performing microflotation tests. Possible implications to the flotation separation of chalcopyrite-pyrrhotite ores are discussed.

Jan 1, 1995

By Michael G. Nelson

A computer simulation of the automatic control of continuous mining machines has been prepared, similar to previous simulations of longwall mining systems and coal thickness sensors. The simulation allows for programmed variation of the horizon detection method, the azimuthal guidance system, the type and configuration of the miner, varying hardness in the unmined face material (leading to varying error in the machine heading), and the miner's cutting cycle. It simulates control of the miner in three axes. Use of the simulator makes it possible to anticipate problems arising from the complex character of underground mining, which include unpredictable multi-pass coupling and unpredictable variation in geological conditions.

Jan 1, 1993

By M. J. McPherson, P. Mousset-Jones, G. Danko

Ventilation and refrigeration fortune climate modification contributes significantly to the operating costs of a deep hot mine. Mine climate simulation programs can he used to minimize the impact of these costs. There are several computer codes available to assist in this work. Whichever simulation program is used, it is the mine ventilation engineer who must supply the input data. This paper raises and answers the following question, namely, what accuracy is required of the basic input parameters, in order for a certain precision to he obtained in the predicted air temperatures? In the first part of the paper a new approach is described to estimate the dry and wet bulb temperature of the airflow, either in a dry or wet roadway. The calculation procedure allows an arbitrary temperature change with time, using Duhamel's superposition solution. Matrix-vector representation is applied to simplify the computational structure. In the second part of the paper the sensitivities of the dry and wet bulb air temperatures are analyzed, to the changes of the rock thernrophysical properties, the heat transfer coefficient, and the wetness factor.

Jan 1, 1987

By D. A. Peterson

Laboratory testing was completed to determine the effectiveness of a fiberglass cable bolt (FCB) as a cuttable rock support for a continuous, hard-rock mining method. The FCB consists of four Polystal tendons combined in a node/antinode fashion, with polyvinyl chloride (PVC) spacers forming the anti-nodes. The largest ultimate pull-out load achieved by the FCB was 22 t (48,400 lb) at 89% of the tendons' theoretical pullout load. This premature tendon failure is accredited to: • differential stresses within the tendons and • differential tendon displacement. An increase in pull-out resistance for a given embedment length is due to: • increased bond area, • reduced interfacial shear and • "wedge" effect. The critical embedment length was found to be 40% less than for conventional steel cable bolts (SCB) at a 127-mm (5-in.) node spacing. An FCB can have up to a 92% increase in load-carrying capacity over a conventional SCB at equal embedment lengths. The load carrying capacity is equivalent to SCB at a 960-mm (37.8-in.) embedment length. Though the FCB is 7.5% more expensive than the conventional SCB (installed), this cost may be offset by increased performance. FCBs are a potentially viable support alternative for continuous hard-rock mining.

Jan 1, 1993

By Guocheng Pan

This paper presents-:a new multivariate mineral resource estimation model, referred to as the Related. Information (RI). Instead of relating a mineral resource descriptor directly to a set of geological variables, the RI model relates the mineral resource descriptor to a synthesized information measure RI, which is created from a set of geological variables. All of the variables are transformed into binary characteristics. This model comprises two stages of estimation: estimation of a synthesized information measure and estimation of mineral resources. The information carried by a variable is classified into three types: mineralized-barren information, mineral resource variation information, and variable-controlling information. The synthesized information measure is defined as the product of the three types of information and the responses of binary geologic characteristics. The RI model is demonstrated on the pegmatitic Nb+Ta deposits in China.

Jan 1, 1992

By M. M. Hajdasinski

For decades, the internal rate of return (IRR) project-evaluation criterion has been under increasing criticism. Torries (1998a) defends the beleaguered criterion. He claims that, as a project-evaluation and ranking instrument, the IRR is as suitable as the net present value (NPV). Torries also maintains that using the IRR to rank projects does not require the incremental approach and introduces his own alternative ranking approach. This paper disputes Torries' pro-IRR arguments and demonstrates that the IRR is a theoretically flawed and operationally dysfunctional criterion whose true meaning has persistently been misinterpreted. In a forthcoming paper by the author it will be shown that Torries' IRR-based project-ranking approach is flawed as well.

Jan 1, 2000

By Robert Dimock

The successful management of large dispersed mineral operations is dependent upon accurate and timely decision making. The plant locations providing the data to support the decision making process are generally separated by distances which elongate the time required to accumulate the data at a central focus. The need exists to examine operational data in context with total mining operations, and in relation to target projections and historical trends. The use of microcomputers for local information tasks is an established capability. Grouping microcomputers into local-area networks is rapidly becoming established. Interconnecting multiple local-area networks to provide a free flowing stream of information between all operational locations of a mining enterprise is possible with use of some emerging technologies. The benefit of the potential interconnections and rapid transfer of information can readily be seen from a production reporting perspective. Numerous other advantages exist' by providing routing to enable a workgroup to be established between separated work functions.

Jan 1, 1989

By Jacek Kolacz, Knut Lyng Sandvik

Fine grinding in an air swept and a grate discharge ball mill working in closed circuit with a forced vortex air classifier has been investigated in continuous laboratory scale. Minerals with different physical properties were ground down to 40, 20, and 10 micron top size. The shape of the product particle size distribution curve was investigated and specific surface (BET) was measured. During production of material with top size of 40 microns in an air swept mill, the capacity was up to 25% higher when compared to a grate discharge mill. This difference dropped to 180A during production of 10 micron top size material. A corresponding decrease in power consumption was observed. An important finding is that by regulation of the air flow rate through the mill, it is possible to achieve products with different specific surfaces and particle size distribution curve steepness. During production of the 10 pm material, the specific surface could be varied in the range 3 to 4.5 m2/g. Such powders could hardly be produced in a grate discharge mill because fine particles coated the grinding media and the lining. On the other hand the internal classification in the air swept mill kept the size distribution of the mill content relatively free of fines. This prevented a similar slowing-down of the air swept grinding process.

Jan 1, 1995

By R. Larry Davis

Over the past decade there has been a continual decrease in domestic oil reserves accompanied by a sharp increase in the demand for energy. Even with increased imports of foreign oil, the energy demand has not been met. This has forced many users to turn to substitute fuels. Of the many substitute fuels available most users are turning to and creating an increased demand for low sulfur coal. Because of the increased demand for low sulfur coal as well as the inherent problems in producing eastern coal, many producers have turned their attention to the large deposits of low sulfur coal in the western United States. Western coal mining is, however, not without its problems such as high moisture content, high ash content, highly variable sulfur content, multiple seams, and/or pitching seams. It is to aid in the solution of these problems that this chapter is directed.

Jan 1, 1979

By H. Huang, J. C. Wu, C. H. Xie, Y. Q. Xue, Z. H. Zhang

Two- and three-dimensional groundwater flow models for dewatering in an opencast mine are presented. The models focus on solving special problems using numerical simulations of the opencast mine. These special problems include the drying up of the aquifer, the movement of the model boundary and the prediction of the residual head. These models are used to describe the decline of groumdwater levels in the Yuanbaoshan Opencast Coal Mine and its neighboring area during the drainage period. The simulated values agree very well with the field data. There have been several successful examples of numerical simulation for predicting the mine dewatering rate in an opencast mine. However, The hydrogeological conditions for the Yuanbaoshan Opencast Coal Mine are rather complex, and the total average flow rate is very high at 4.676 x 105 m3/d (1.65 x 107 cu ft/day). In this paper, a two-dimensional groundwater flow model in a large area is developed to solve the problems mentioned above by simulating regional drawdowns of the groundwater level during the drainage period, and a three-dimensional flow model is developed to simulate the residual head near the open-pit bench.

Jan 1, 1998

By Victor Rudenno

Cut-off grade is one of the most critical parameters affecting project cash flow. Its sensitivity is due to the number of other parameters that are correlated with any change in its value. Changes in cut-off grade, average grade and ore tonnage vary and they in turn can affect such parameters as capital and replacement costs, recovery, life of the project and operating costs. Perhaps one of the best definitions of cut-off grade is that of Taylor (1), "... any grade that, for any specific reason, is used to separate two courses of action, e.g. to mine or to leave, to mill or to dump ... . Obviously the most likely specific reason is one governed by economics, involving the return of investment and sufficient profit to motivate development and mining of the deposit. In this paper the cut-off grade is defined as that mining limit which will maximise the economic return for a projected mining venture. The following brief literature survey indicates that when computing the optimum cut-off grade there is a need to be able to directly compute the Discounted Cash Flow Rate of Return (DCFRR) or Net Present Value (NPV), as economically as possible, while allowing for parameter dependencies and variation in project structure.

Jan 1, 1979

By A. E. Prokop, J. P. Rider

Previous research on continuous mining operations has shown that significant interactions exist between dust-control parameter application and the resulting respirable dust levels. However, simply increasing the level of the controls does not guarantee a reduction in respirable dust levels. Full-scale laboratory tests are being conducted to provide information to longwall operators that would assist them in selecting control parameters to reduce dust levels for mine-specific conditions. The interactions between face air velocity, shearer water quantity, drum water spray pressure, external water spray pressure and spray system design were evaluated in a simulated 2.13-m (7 ft) coal seam for two cutting directions. Locations around and downwind of the shearer were monitored to evaluate relative changes in respirable dust levels as a function of each control parameter.

Jan 1, 2003

By A. J. Hendron, B. Mohraz, R. B. Peck

INTRODUCTION The state of the art of soft-ground tunneling was discussed in detail by the senior author at the 7th International Conference on Soil Mechanics and Foundation Engineering held in Mexico City in 1969. Little can be gained by repeating the information assembled at that time. Hence, in this report, only the briefest summary will be given of the overall state of the art and attention will be concentrated on trends and developments since 1969. A characteristic of recent developments is the continued trend toward use of shields and excavating machines. The implications of this trend with respect to design and construction, and particularly with respect to the treatment of unfavorable ground conditions, will be examined. Settlement associated with lost ground, a subject as old as tunneling itself, will be reviewed and methods will be considered for its reduction. Design of tunnel supports was discussed in detail in 1969 with respect to essentially rigid or essentially flexible types of linings. In this report, a definition of flexibility will be considered and design procedures suggested for linings of flexibility intermediate between the two extremes.

Jan 1, 1997

By M. R. Fletcher

Slags generated by the ferrous metals industry can he used to produce high-value ceramic materials. The properties of these ceramics can be controlled by judicious choices of composition, additives, and processing parameters. Standard methods of materials handling, such as comminution and mixing, are as applicable to slag as to any other mineralogic raw material. In this study, foundry slag was ground, homogenized, melted, and, formed to produce a glass, and then heat treated to crystallize it into a high-strength glass-ceramic. The product shows promise as a low-cost, wear-resistant tile material that (-an he custom cast. This and similar materials made from slags and natural rocks are candidates for use as construction materials, acid-resistant piping, shock-resistant sheathing, rot-proof pilings, and, when foamed, even as pontoons.

Jan 1, 1990

By K. Biswas, S. J. Jung

Health and safety of workers in mineral industry in the U.S. is still a vey important issue as Mining along with Agriculture, Forestry and Fishing and Construction industries have contributed most of the fatal occupational injuries ill between 1980 - 1995 (Worker Health Chartbook, 2000). Health and safety issues, especially for the mining or related excavation industries, arise either from exposures of the human workers to the contaminants liberated or generated by mining operations that have adverse effects on human health (for example coal dust etc.) or from the exposures of the human workers to hazardous working environment that constitutes mining operations (for example blasting etc.). One of the biggest challenges is to understand the combinatorial effect of numerous work-condition (e.g. exposure to dust) and human-factor (e.g. smoking habit) variables on a health or safety-condition variable (e.g. incidence rate of a disease). This paper uses an example dataset on Coal miners' cough problem to illustrate the applicability of Generalized Linear Modeling (GLM) in understanding the relation between cough and other response variables, such as, age, height, smoking habits, time of underground exposure etc.

Jan 1, 2002

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of massive pillar failure in a room-and-pillar mine that employed nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated outby quickly and within 24 hours it had covered an area approximately 1,250 m long by 762 m wide (4,100 x 2,500 ft). The failure was caught and stopped by a solid barrier pillar. Using computer modeling, the study indicated that the massive failure was initiated due to a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of no barrier pillars between some panels and between mains and panels. Based on the computer modeling, alternative mine plans have been proposed to avoid such problems.

Jan 1, 2000

By Pentti Kallio

From the aspect of economic feasibility of mining, ineffective use of expensive mechanization investments is becoming a problem. In many cases, the machinery is in operation only 50 - 60 % of the total working time. The lost time when the machines are idle means a considerable over-investment in machines. The lost time, with LHD equipment in particular, accumulates from the following constituents: - the needs of the person operating the machine trips to the work site, lunch, coffee and other breaks, want for comfort, etc. - deficiencies in the monitoring and control systems for machine operation waiting periods at loading and unloading stations, unnecessary and erroneous actions, inefficient work, etc. - deficiencies in the machine condition monitoring system , and inefficient service and maintenance work The data transfer and computer technology of today provides means for resolving problems in several areas - including the area of underground loading operations. In the paper those areas of automation and data handling are considered which make possible an improvement in the usage and monitoring of LHD equipment. These fields are: remote control of equipment, use of TV cameras and monitors in remote control, locating equipment and data transfer down the mine, measurement of the load and the data storing system, systems for following the condition of the equipment, unmanned operation of equipment.

Jan 1, 1989