Search Documents

By D. V. Professor Keller

The production of premium coal-based fuels (<3% ash) and ultra clean coals (<1% ash) using the process of selective agglomeration requires proper selection of raw coal, rough preparation procedures, milling equipment, product coal size distribution, water purity, agglomerants, agglomeration equipment and operational procedures. Each of the variables can contribute a small fraction to the impurity load in the product coal or limit the ability of the process to separate mineral matter-free coal. Each of the variables and their importance will be examined from data produced at the bench by batch and continuous agglomeratons as well as the results from pilot plant and tonnage production units. The results are discussed which have indicated that some standard commercial coals can be produced with ash contents as low as 0.2 % ash (batch/bench) and several tonnage lots of 0.6% ash in as 200 lb/hr pilot plant. In most cases iron pyrite released from the coal matrix and with proper pH control is rejected from the product coal agglomerates.

Jan 1, 1995

By J. Felipe Costa, Andrew H. White, Marcot T. M. B. Vilhena

Ordinary kriiing (OK) is an interpolation algorithm mostly used in earth sciences applications where it provides satisfactory results. Robust kriging (RK) is an alternative algorithm which at- tempts to minimise the problems caused by the existence of outlier values within a given data set. Robust kriging essentially consists of an editing step prior to running the traditional OK method. This study compares the interpolation results obtained by OK and RK. Two data sets were used. The first data set consists of 140 samples mimicking a drilling survey named cluster.dat. An additional feature of this sample data is that its parent population, the reference data set, is available, thus permitting direct quantitative assessment of the effectiveness of a given estimation technique. The second data set consists of a grid sampled at 1x1 m. The estimates obtained by OK and RK using cluster.dat were compared to the reference data set. RK provided better results in terms of quality of the estimates than OK

Jan 1, 1996

By Arthur E. Lord, W. Martin McCabe, Robert M. Koerner

Following the driving of each new section of tunnel, a prompt decision is required regarding the type and extent of primary support to control convergence and prevent ground failure. Sometime thereafter, the effectiveness of the in-place support must be evaluated over the entire length of excavation. It is therefore extremely desirable to have available a lightweight, portable, easy to install and interpret, cost effective monitoring system to assist with these ground control functions. Such a system can be assembled based on the acoustic emission (or microseismic) technique. This monitoring technique uses a piezoelectric transducer to detect subaudible noises associated with deformation of and/or crack propagation in the soil or rock being monitored. After detection, the signals are then amplified, filtered and electronically counted to provide a quantified assessment of the stability of the structure. In the simplest sense, the absence of emission, or counts, signifies no deformation and thus stability. Conversely, the occurrance of counts signifies instability to varying degrees. The higher the count rate, the greater the instability and the need for immediate or additional support. Described in this paper is an overview of the acoustic emission (microseismic) method, details of its use in a laboratory study measuring convergence and stand-up time in soil, and the behavior of rock samples under similar stress conditions. Field use of the method is recommended for ground control monitoring in tunnels, and some suggestions regarding monitoring procedure are presented.

Jan 1, 1979

By Byron N. Cooper

The Revenue Act of 1926 provided for five simple categories of natural resources to have the benefit of depletion allowances. In the 1947 Revenue Act, the number was increased to twenty-five, and in the 1951 Revenue Act to fifty-four. Of this number, fourteen were allowed 5 per cent; nine, 10 per cent; twenty-nine, 15 per cent; one, 23 per cent; and one (oil and gas), 27.5 per cent. The 1951 Revenue Act created a host of difficulties, including application of the "end- use criterion" and determination of the commonly accepted meaning of such terms as limestone, dolomite, chemical- and metallurgical-grade limestone, marble, calcium carbonates, and magnesium carbonates. Dolomite, for example, was listed at 10 per cent depletion allowance, but without definition. In the great amount of litigation growing out of the 1951 Revenue Act and its administration, it became essential to understand the derivation and subsequent usage of these common geologic terms. One thing that became clear was that our definitions changed significantly between the time that the 1951 Revenue Act became law and the time that later cases were tried. Some geologists neglected to learn about first usages of such terms as metallurgical limestone, and about meanings that were applicable when the 1951 Revenue Act was written and passed. Legal meanings in this paper are discussed in the light of certain famous cases that have been tried and settled.

Jan 1, 1966

By M. J. Virnig, C. P. J. Van Vuuren, A. J. Botha

The Zadra, AARL and organic elution processes and variations of them are presently widely used to recover gold from activated carbon. Despite this the study of the kinetics of elution have received relatively little attention. It is the aim of this study to investigate the rate processes taking place during elution in both inorganic and organic solutions. Batch adsorption and elution rate and equilibrium experiments were performed. The spatial concentration of gold inside carbon particles at various stages of the adsorption and elution processes were measured with a scanning electron microscope using an image analyzer to control and manage the micro-analysis data. The activated carbon particles exhibited film and intra-particle mass transfer rate- controlled behaviour during adsorption in a caustic aqueous solution at 95°C. Elutions in the aqueous caustic acetone solution at 30°C and the caustic aqueous solution at 95°C were unaffected by change in stirring rate. Elution was modelled by desorption reaction rate-control at the outer surface of the carbon particle. Adsorption and elution isotherms under duplicated solution conditions showed reasonable agreement for the inorganic solution and a large disparity for the organic solution.

Jan 1, 1993

By A. M. Al Taweel, S. M. El Mofty, T. A. Hassan, M. R. Moharam, A. M. Ramadan

The axial mixing characteristics of a pilot-scale flotation column were investigated with the objective of identifying means to mitigate the extent of axial mixing that adversely affects its grade/recovery performance. A wide range of design and operating conditions was investigated and the experimental results, obtained using the dynamic response method, were analyzed using three axial mixing models. The dynamic response of the column can best be described using the axial dispersion model. The results obtained suggest that the value of the axial dispersion coefficient, EL. can be signi6cantly reduced by judicial selection of hydrodynamic conditions and/or the use of column inserts that suppress the onset of hydrodynamic instabilities inherent to the operation of conventional flotation columns. Up to 40% reduction in the value of EL was thus obtained by using spargers that produce more uniform bubble sizes, while up to 30% reductions were obtained by controlling the residual frother concentration.

Jan 1, 1995

By Barbara Maren Winkler

For mine production problems in mines with varying qualities, both open pit and underground, the linear programming method (LP) has been used successfully. By this method it is possible to keep the total production blend for each period within a required range of qualities while optimizing objectives like production costs, net return, ore grades, other qualities, or a combination of these. Technical restrictions like constrained capacities can be added to the model. This makes LP a flexible and powerful tool for mine production planning. Practical experiences have shown the major influence fix costs have on the actual economic result of a planning decision. It can be proven that fix costs cannot be included in LP models. We describe a way to address this fix cost problem by using mixed integer linear programming (MILP) as an extension to LP in the optimization of a mine planning problem. This raises the issue of complexity. We discuss the computational complexity of the resulting models and the enhancement of model flexibility for the user of a planning system. We demonstrate the method embedded in a practicable everyday planning system for a complex underground coal mine. By computational examples we show how the method improves the economical results of the planning.

Jan 1, 1996

By Steve Kral

When discussing stock market investments, a company&apos;s performance is important. But so is the financial community&apos;s perception of that performance. To be sure, a good product or service, coupled with sound manage¬ment, remains important but is no longer enough. How stock analysts view a company&apos;s performance has become equally important. A major task of a mining company&apos;s investor relations officer, then, is to build and maintain a positive perception of the company to mining analysts throughout the world. That&apos;s a tough assignment in any market. The subject here, though, is gold. And, with its weakened price, gold companies must work harder to convince analysts their company is still a good investment. The analyst, on the other hand, must see through the corporate hype and decide whether it&apos;s worth recommending to clients as an investment. No simple task, either. Annual reports, 10-K forms, and quarterly reports only tell part of the mining company&apos;s story. Site visits, complete with discussions (sometimes interrogations) with a mine&apos;s principals, oftentimes tell an analyst more about a company&apos;s investment potential than the annual or quarterly report. So it was that three of the nation&apos;s major gold companies arranged a three-day tour of their gold operations in Nevada for a group of 22 analysts and a pair of mining industry scribes. The analysts represented investment houses the US, Canada, and England. The host companies and mines visited included FMC Gold&apos;s Paradise Peak mine, Amax Gold&apos;s Sleeper and Wind Mountain mines, and Battle Mountain Gold&apos;s Surprise and Fortitude mines.

Jan 1, 1989

By Charles L. Karr

Grinding is a necessary component in the processing of a number of minerals, and improvements in this area could provide substantial cost savings for the minerals industry. Optimizing the process of grinding, however, is a difficult task because there are multiple objectives; i.e., several aspects of the process are important including the fineness of the ground product, the energy consumed in the process, and the viscosity characteristics of the final slurry. Genetic algorithms (GAs) are search algorithms based on the mechanics of natural genetics and have been proven capable of solving multiple objective optimization problems. These robust search techniques are able to rapidly locate near-optimum solutions across a broad spectrum of very difficult optimization problems. In this paper, two varieties of GA are used to optimize a grinding process as it is described by a computer model: (1) a simple genetic algorithm (SGA) and (2) a micro genetic algorithm (MGA). The performance of these techniques is compared to the performance of a more conventional search technique, a simplex algorithm. Results indicate that the GAs are efficient, versatile, quite capable of improving the grinding process, and easily incorporated into the toolbox of today&apos;s process engineer.

Jan 1, 1993

By N. Colvin, J. W. Gulyas

HISTORY The Surigao Nickel Refinery of Marinduque Mining and Industrial Corporation is located on Nonoc Island off the northwestern coast of Mindanao in the Philippines. Nonoc Island is part of the Surigao Mineral Reservation which had been identified as early as 1912. Initial interest in these deposits was due to their iron content, and their value as a nickel deposit was not seriously entertained until the late 1950&apos;s. The Philippine government undertook extensive test pitting and sampling programmes at that time and in the early sixties Marinduque became involved in helping to establish firmer ore reserves. Evaluations of the test pitting programme indicated reserves of 75,000,000 tonnes of ore averaging 1.22% Ni, 0.1% Co and 38.5% Fe. The Philippine government called for bids on the reservation in 1962 and Marinduque and Sherritt Gordon carried out some feasibility studies for the recovery of nickel from the deposit. However, it was not until 1968 that Marinduque was granted proper authority to exploit the Surigao deposits. Marinduque and Sherritt then entered into an agreement which allowed Marinduque to utilize a process developed by Sherritt for treating lateritic ores. During 1968, a 25 st/d pilot plant was erected in Fort Saskatchewan, Alberta for the purpose of modelling all process steps. A 10,000 tonne ore sample was sent from Nonoc as feed stock for the pilot plant.

Jan 1, 1979

By Philip U. Santacroce, James H. Meinholz

INTRODUCTION The Milwaukee Metropolitan Sewerage District (MMSD), is a special purpose sub-regional agency that provides collection and treatment services for sanitary wastewater for an area of 420 square miles (1088 km2) in 27 municipalities in the Milwaukee, Wisconsin metropolitan area. During its almost 75 years of existence, it has constructed 464 km of intercepting sewers, the majority in tunnel, and two sub-regional secondary wastewater treatment plants. The present program, the $1.7 billion Milwaukee Water Pollution Abatement Program, was started in 1977 and developed from ongoing internal planning, the Federal Clean Water Act and court judgments. Elements of the Program include improvement and expansion of the two treatment plants; rehabilitation of older in-place sewers; building new interceptors and relief sewers and providing capacity for high volume storage in approximately 32 km of deep, large diameter rock tunnels; reducing combined sewer overflow; and disposal/utilization of the solids that remain after the treatment process. The construction phase of the Program accounts for $1,105,900,000 within 335 separate construction contracts, 211 let to date, and covers a span of 15 years, starting in 1979 and running through 1994. Conveyance System construction cost is estimated to be $650,000,000 or about 60 percent of the total. Through December 1986, in terms of dollars, the total construction program is about 38 percent complete with Conveyance at 34 percent complete.

Jan 1, 1987

By W. Morgan, D. Gove

In truck and shovel operations, productivity and cost per ton are influenced by the system matching choice, Optimization involves a balance of the size and number of trucks, the size and type of loading tool and the projected material conditions and haul roads. Caterpillar has updated its Fleet Production and Cost program so miners can more easily look at matching choices and optimize on the variable they choose. This paper introduces the Fleet Production and Cost program. It then demonstrates its capabilities with examples of optimization. Mining operations that use trucks need to properly match the number and size of hauling units (trucks, wagons, scrapers, etc.) to a loading unit (wheel-loader, hydraulic shovel-excavator, cable shovel, push tractor, etc.) to provide the best possible fleet match. Optimizing fleet match minimizes the cost per unit of material moved by that fleet. As haul conditions change (haul length, grade or rolling resistance), there may be need to adjust the number of trucks to maintain the optimum fleet match. Fleet Production and Cost is a tool that can be used to optimize the truck-loader match.

Jan 1, 1995

By M. Balakrishnan, K. A. Natarajan, J. M. Modak, J. S. Gururaj Naik

The ability of various fungal species isolated from gold mines to uptake gold and base metals such as zinc, copper, iron and lead from gold-process cyanide effluents was investigated. Under identical treatment conditions, different strains showed wide variations in their ability to take up gold and other base metals. Aspergillus terreus exhibited as high as a 60% gold uptake. Almost complete removal of zinc was possible with various fungi and with the yeast Saccharomyces cerevisiae. Studies at various metal concentrations showed a higher gold uptake from dilute solutions, and studies with Aspergillus niger showed that gold uptake by living cells increased gradually as the contact time increased. Metal uptake capacities between living and nonliving cells were also compared. A waste biomass (ABM- I), obtained from a fermentation industry, wasalso identified as having a high gold uptake capacity. At 5% (W/v) solids, ABM-I could efficiently remove up to 83% of the gold contained in an effluent solution within 24 hrs.

Jan 1, 1995

By Tso-Min Shih, Ching-Hua Liu, Chung-Jen Lin, Hsi-Chiang Fang

This paper presented herein, describe the special design of an open type coal dust explosion apparatus and the laboratory works for investigating the effectiveness of the parameters on coal dust explosion and the prevention of the propagation of the coal dust explosion flame. Coal sample which were taken from the San-Ying collieries, were passed through the process of crushing ,grinding and screening to get the required particle size, ranged from 40 mesh to 200 mesh under size for testing purpose, the rock dust spreaded on the surface of coal dust and water mixed with coal dusts were employed for preventing the coal dust explosion and the propagation of the explosion flame.

Jan 1, 1991

By William C. Cooley

Modern tunnel boring machines are subject to excessive cutter wear and bearing failures when used in hard and abrasive rock. In very hard rock, the high cost of cutter and bearing replacement, combined with slower excavation progress, make it more economical to drive tunnels by conventional drill and blast methods. The use of high pressure water jets to break rock provides a promising alternative. Experimental data indicate that the specific energy (the energy expended per unit volume of rock broken) decreases as the water jet pressure increases. Continuous jets are generally limited to pressures below 100,000 psi, whereas pulsed jets from a water cannon can attain much higher pressures. Therefore, the Federal Railroad Administration of the U. S. Department of Transportation has sponsored the design (Ref. 1 & 2) and the fabrication and testing (Ref. 3 & 4) of a water cannon to determine its effectiveness in rock disintegration at very high pressures. This paper reports the results of laboratory tests with pulsed jets against large rock samples at pressures of 125,000 to 650,000 psi and field tests against dolomitic limestone and granitic gneiss at pressures near 450,000 psi. Although initial tests were made with a small nozzle, operating at off-design conditions (Ref. 4), this paper only covers results with the full-size nozzle, including 55 laboratory test shots and 67 field test shots.

Jan 1, 1974

By Adrian Smith, Debra W. Struhsacker

There is now overwhelming evidence that, despite concerns to the contrary, natural degradation of cyanide and cyanide attenuation by hydrogeochemical processes are capable of minimizing or eliminating potential water qua1ity impacts from heap leach systems. A1 though there was some recognition of these data by the regulatory authorities, for example the initial USEPA modification of cyanide standards to an advisory level, many states have codified standards inappropriate to the clearly site specific nature of heap leach operations. As an overview to this problem, this paper will integrate the theoretical chemical data on cyanide with the observed geochemical behavior of cyanide in the decommissioned heap leach environment. The cyanide species that are likely to exist within an abandoned heap leach system will be identified, and the relative toxicity and potential environment effect of these cyanide species will be discussed. These data will then be used to evaluate cyanide detoxification regulations for decommissioned heap leach projects in 14 states.

Jan 1, 1987

Over the past few years, the School of Mines of Paris has carried out a program of research* on the grade-tonnage relationships in the border zones of porphyry copper deposits. The initial problem was quite difficult : how does the grade vary at the border of the known orebodies? Does it decrease regularly, or do some thresholds exist, where the grade diminishes abruptly? The answer to these questions have important repercussions on the prediction of the future reserves in the fringe of the orebodies. If the grade decreases regularly, very important reserves could exist; if not, there would be strong limitations to the possible recoverable reserves. The first step of our study was a critical study of previous work done on the subject. It appeared that, following Lasky&apos;s pioneering paper (Lasky, 1950), most of the authors used what we can call an historical approach to the problem. In this, the grade-tonnage relationships are calculated from the available figures for production and reserves and the results are then extrapolated to the future. The strong limitation of this model are brought out in this article.

Jan 1, 1982

By John A. Herbst, Per-Olaf Samskog, Jan Bjorkman, Yi Chang Lo

The study described here is concerned with the development of a model for the simulation and optimization of a rod milllpebble mill circuit. A series of laboratory tests was conducted to investigate the effect of critical operating variables. The pebble mill model structure used was a population balance type which accounta for impact breakage and fines production from pebble wear. Model parameterization and verification were performed using data obtained in batch tests and in a plant test campaign. The model developed was found to provide accurate predictions of plant-scale grinding. The prediction errors are less than 21 for the product size and 31 for the mill power required to achieve that product with a mill volume scale-up of 14,000 to 1. These results indicate that accurate extrapolations from laboratory batch data to plant scale performance are poaaible using the population balance model and scale-up prediction procedures for pebble mill circuits as well as ball mills. Preliminary indications are that the new model developed here will provide vital input for pebble mill optimization and process control as well as pebble mill design.

Jan 1, 1990

By T. McWaters

In 1911, Miami Copper Co. began a block caving operation at its Miami, AZ property. A gravity mill was used to separate copper minerals from the Pinal Schist host rock. Until 1932, the mill tailings were deposited by the upstream method using perimeter launders and spigot valves in six canyons adjacent to the mill. In 1928, the larger and more distant Solitude tailing pile was developed. By 1932, it was receiving all tailings. In 1925, Miami Copper converted the gravity mill to flotation with sulfide copper recoveries. From 1934 to 1943, Miami, Copper ran a leach-precipitate float (LPF) circuit on mined ore and, in 1943, began sulfuric acid in-place leaching of a portion of the caved area formed by block caving. The pregnant solutions were collected underground and pumped to the LPF precipitating drums to harvest copper. In 1954, the company started mining low-grade ore. This led to the running an old LPF plant on select mill tailings from April 1957 to March 1959. In 1959, block-cave mining ceased. Solution mining became the only source of production using a launder precipitation plant. In the mid-1960s, Miami Copper merged with the Tennessee Corp. In the latter part of the decade, Cities Service Co. bought the combined properties. In 1976, Cities Service commissioned a 15-t/d (16.5-stpd) solvent extraction electrowinning(SX-EW) facility at its Miami copper property to replace the precipitation plant. In 1982, Occidental Petroleum Co. bought Cities Service. In 1983, the Miami operations were sold to Newmont Mining Corp. and set up as a subsidiary company, Pinto Valley Copper Corp. Finally, in 1987, Newmont Mining spun off a combined Pinto Valley and San Manuel unit as Magma Copper Co.

Jan 1, 1990

By Bryan C. Smith, Duane R. Skidmore

Volumetric mass transfer coefficients and gas holdups were measured in a concentric tube airlift reactor designed for the microbial desulfurization of coal. The slurries were comprised of an acidified basal salts solution containing thirteen different weight percents of coal (74 µm Ohio #1) at three temperatures. An enhancement in the mass transfer coefficient, KLa, with respect to that measured in pure solution was found at weight percents of 5 (volume fraction solids, ES = 0.035) or less, the greatest enhancement being as great as 37% at approximately 2 weight percent (ES = J 0.014). At higher solids fractions, the mass transfer coefficient decreased with further solids additions, decreasing by as much as 91% at 40 weight percent coal (ES = 0.315). KLa increased with temperature at all solids concentrations, the greatest increase being 392% at 72°C vs that measured at 30°C. Gas holdup, EG decreased with all increases in solids loading by as much as 65% and increased by as much as 67% with temperature. KLa and EG were correlated with operating conditions separately, and the separate correlations combined to yield overall correlations for the mass transfer coefficient and for the gas holdup. The correlations are suitable for inclusion in system models devised earlier for microbial coal desulfurization processes, and may be used for design, operation and cost estimation for such systems.

Jan 1, 1989