Search Documents

By Stephen G. Hardcastle

CANMET has developed a simple yet very effective tracer gas method to test the efficiency of stench gas emergency warning systems which can easily be performed by mine personnel. This test method uses sulphur hexafluoride (SF,) as a surrogate for such stench gases as ethyl mercaptan. The test has many advantages: it is non-disruptive to production because SF, is odourless, colourless; it is safe to use as it is inert and only a small volume, insufficient to reduce oxygen levels, is necessary to dope the air with a measurable concentration; and most importantly it provides definitive results to assess the adequacy of the warning system. Specific findings of these tests have included, over doping sections of the mine and subsequent production loss due to sickness, the warning being ignored, the injection period being too short, excessive dispersion, and inadequate notification times. The simple test protocol involves releasing a known volume of the SF, under similar circumstances to those of the stench gas, and then sampling for its presence downstream. These samples are collected in air-tight syringes which are then analyzed in a laboratory with a gas chromatograph. By direct proportion, between the size of the stench and tracer gas releases, it is possible to convert the SF, concentration into equivalent stench gas concentrations profiles. From these, it is possible to define, the initial arrival time of the gas, the time it takes to reach a "target" notification concentration, whether the gas peak will exceed TWAEV, STEV and CEV exposure limits, and the duration of the peak above these levels. Since 1993, this test protocol has been employed a total of eight times on four different Canadian mine properties and the results are being used to optimize the stench gas release system with respect to volume of gas used, duration of injection, and number of injection locations.

Jan 1, 1997

By Romeo S. Jurani

Yucca Mountain, located in Southern Nevada approximately 160 krn northwest of Las Vegas, is currently the site of intensive surfacebased and underground investigations. The investigations are required to determine if the site is suitable for long term isolation of the Nation's high level nuclear waste inventory. A major component of the program is the Exploratory Studies Facility, or ESF. The ESF, when completed, will consist of approximately 25,600 meters of tunnels and drifts. The network of tunnels and drifts (Figure 1) will house and support a wide array of testing programs conceived to provide physical information about the site. Information on geologic, geomechanical, and hydrologic data will be used in the repository design if the site is found suitable. Besides a few special requirements, the general ESF ventilation criteria during construction are similar to that of commercial tunneling and mining operations. The minimum air velocity at the Tunnel Boring Machine (TBM) and other active mining faces is 0.51 meter per second (m/s) (100 feet per minute [fpm]). Airways, estimated leakages and ventilation controls are converted into equivalent resistances for input to mine ventilation network computer simulations. VNETPC Version 3.1 computer software is used to generate the ventilation models for optimized system design and component selection. Subsequently, actual performance of the ventilation system will be verified and validated to comply with applicable nuclear regulatory quality assurance requirements. Dust control in the ESF is dependent on effective dust collection, enclosure, and airflow dilution. Minimum use of water, as feasible, is necessary to avoid adding moisture to the potential repository horizon. The limitation of water use for test drilling and TBM operation, and the rigid compliance with applicable federal and state regulations, make the ESF a ventilation design challenge.

Jan 1, 1995

By R. Gong, R. Bhaskar

[Full-scale laboratory experiments were performed to evaluate the effect of ventilation and water spray pressure on the potential dust capture efficiency of a ventilation system comprised of blowing ventilation and an underboon scrubber. The tests were performed for a 1.52-m (5-ft) roof height and 2.36 m-3/s (5000 cfm) blowing ventilation volume, and a 2.44-m (8-ft) roof height and 4.72 m3/s (10.000 cfm) blowing ventilation volume at three face positions of the miner. The scrubber suction rate was varied for the tests to study the effect of scrubber flow rate on capture efficiency. The airflow patterns and scrubber efficiency were determined by performing tracer gas tests. Tracer gas was released through a manifold placed in front of the rotating miner drum. The gas was sampled in a grid fashion using a real-time multi-point gas sampling system. The capture efficiency of the scrubber was evaluated based an the peak gas concentration of the gas laden air drawn through the scrubber and the amount of gas passing, through the scrubber as a fraction of the gas released at the face. The data were analyzed to yield scrubber peak concentrations, potential exposures at various operator locations and the gas removal percentage (GRP). The underboom scrubber appears to work best in the end sump position, relative to the start sump and start slab positions. The capture efficiency scrubber was higher for 2.44-m (8-ft) roof heights compared to 1.52-m (5-ft) roof heights. The data also showed that the scrubber air discharged behind the mining machine may be drawn into the face area by the action of the blowing ventilation system, resulting in recirculation.]

Jan 1, 1994

By Robert J. Ramsey, N. Finkelstein, Foster J. Witthauer

First mining operations in the Tyrone District, located just north of the Burro Mountains in Grant County, New Mexico, commenced in the 1870's. A major operation was undertaken by Phelps Dodge Corporation in the early 1900's when a 2,000 ton per day underground mine was developed and a gravity concentrator was built east of the mine and across the Continental Divide. It was during this time that the picturesque Tyrone townsite was built and occupied. In 1921, however, the underground operation was closed because of high operating costs and low demand for copper. The area was drilled extensively during the 1950's and in October 1966 Phelps Dodge announced the pending development of the new Tyrone with a large open-pit mine, a modern concentrator, suitable support facilities, and a new townsite to be located between the mine and Silver City. Stripping for the pit and construction of shop and milling facilities began in 1967. By the spring of 1969, ore was being stockpiled near the primary crusher. Operation of the concentrator on a 3-shift per day basis commenced on July 17, 1969. The concentrator as initially built had one primary, two secondary, and five tertiary cone crushers, two grinding sections of six ball mills each, two flotation sections, four filters, and four tailing thickeners. 'he capacity was about 30,000 tons per day. In 1971 and 1972, the capacity was increased to 48,000 tons per day by the addition of one secondary and two tertiary crushers, one section of eight ball mills, one flotation section, two filters, and four more tailing thickeners. Centralized automatic control was built into the original and expanded facilities to the greatest extent possible, considering the state of the art at that time. Installation of additional control

Jan 1, 1976

Stope width was controlled around 3.5 feet for the narrow high grade vein system at Hollister Gold Mine. Without top access, backfill material was pumped from bottom access up into stope through a series of pipes after ore had been slushed out in each mining cycle. Backfill material was changed from one layer of low strength concrete plus one layer of high strength concrete cap to one layer of low strength cellular concrete plus one layer of high strength concrete cap. Backfill cost was cut down to 30 percent during this process. To reduce the steel concrete pipe set up and tear down time which was about 2 to 3 shifts in each mining cycle, steel pipes were left in man-way between mining cycles. Cellular concrete was firstly introduced into backfilling stopes at Hollister mine in Nevada Mining. This process including concrete pump selection, pumping pipe selection, material mixing, material mechanics and quality control were fully covered in this paper. CUT AND FILL MINING CYCLE The most flexible mining method, cut and fill (Figure 1), was used to mine the high grade, narrow steep vein system on this Northern Nevada property which is located eighty miles north east of Winnemucca. Without top access, stopes were accessed through two man-ways on each end, in which people travel ladders and material transport slides were set up (Figure 2). Each mining cycle was called a cut, from 6 to 8 feet high. Overhand sequence was used. Mining cycle started with drill and blast the middle portion of the stope, then expanded towards both ends. Broken ore was slushed into mill hole located at middle of the stope and then mucked out through bottom access into main haulage. Stope length was about 300 feet, which was restricted by slushing distance. Timber man-ways and mill hole would be raised and established for backfill and ready for the next mining cycle.

Jan 1, 2011

By W. Holding

Since the 1975 International Mine Ventilation Congress in Johannesburg there has been a trend in South Africa towards making the mine ventilation departments responsible for monitoring the total environment. This includes the taking of noise and illumination measurements and there is in fact a debate taking place as to whether the departmental title should be changed to 'Environmental Control Department'. The organisers of the 2nd international Mine Ventilation Congress have decided that noise and illumination will not be included as Congress subjects and 'Total Environment' includes only those facets which are open to debate at the Congress. The choice of mine is significant in that while most Congress papers from South Africa will be devoted either to coal mining or to the somewhat unique deep level gold mines, Prieska Copper Mine is a mine which can easily be identified with similar mines in many other parts of the world. The mine is situated some 750 km south west of Johannesburg and about 600 km north east of Cape Town. Current production (ore and waste) is about 340 000 tons per month and the total underground labour force is just over 2 000. The ore body is a massive sulphide, the main minerals being copper and zinc and the method of mining is sub-level open stoping. Daily average surface temperature conditions range from 85°F (29.5°C) dry bulb and 69.8°F (21°C) wet bulb in mid-summer to 42°F (5.5°C) dry bulb and 36.5°F (2.5°C) wet bulb in mid winter. The information presented in-this paper is limited to what can be gathered by mine ventilation staff as part of an on-going exercise and is obviously not as comprehensive as would be the case if a fully equipped research establishment were to become involved. The paper will be divided into three sections 1) Gases 2) Dust 3) Heat In each section statutory and/or other standards will be set down followed by a discussion of assessment and in some cases control methods.

Jan 1, 1980

By Elvin R. Beach, Jaroslaw Drelich

Pull-off forces were measured for 8-9 pm diameter polystyrene (PSI particles on smooth spin- coated polystyrene films and hexadecanethiol (HDT) self-assemble monolayer surfaces using atomic force microscopy (AFM). Three parameters were controlled during experimentation: (i) the maximum applied load pressing the particle onto the substrate was varied from 50 to 4,000 nN, (ii) loading/unloading rate for the particle to attach and separate from the substrate varied from 0.01 to 9.3 Hz, and (iii) contact time for particle to reside on the substrate surface before retracting the particle to separate it from the surface changed from I µsecond to 200 seconds. the pull-off forces increased with increasing applied loading, increasing loading/unloading rate, and increasing contact time for the PS particle on PS film and on HDT monolayer. The PS particles experience elastic and plastic deformations duringpull-08 force measurements. Plastic deformation is primarily associated with flattening of surface irregularities. The results obtained in this research suggest that the particle-substrate contact areas of the magnitude comparable to those predicted by the JKR contact mechanical model can be reached in the AFM experiments by using high applied loads and long particle-substrate contact times. This result re-opens the prospect of' using AFM for studying surface energies of deformable micro-particles, even if the micro-particles have small irregularities on the surface.

Jan 1, 2003

By Dennis C. Drehmel

Because of their relatively low cost, carbonate rocks are desirable in abatement of air pollution by acid gases. Although many processes and types of equipment have been proposed to control or prevent the emission of acid gases, this paper considers only three: dry-limestone injection, wet-limestone scrubbing, and chemically active fluid beds. For the dry-limestone-injection process, surface area-especially from pores in the 0. 2- to 0.3-micron range-is one of the important parameters which will discriminate between less and more reactive carbonate rocks. Marls, chalks, oolitic calcites, and other fine- grained limestones show larger-than-average surface areas and better- than-average removal efficiencies. Inert chemical impurities such as silica detract from reactivity. A dolomite is not necessarily less re- active than a calcite. For the wet-limestone-scrubbing process, dissolution rate of the carbonate rock controls the differences in stone reactivity. In this process the dolomites are less reactive than the calcites. In addition, more than 90 percent of the dolomitic impurity in Fredonia white lime- stone is inert during limestone scrubbing. Dissolution rate is also a function of particle size for large-grained carbonate rocks. Fine grinding of such rocks will increase the dissolution rate to that of a fine-grained rock. Hence the requirement of high dissolution rates may be met by some grinding of fine-grained material (e. g., marl, chalk, or other limestone) or by fine grinding of coarser grained material. For chemically active fluid beds, chalks have the best capacity to absorb both SO2 and H2S. However, most chalks are probably unsuitable for fluid beds because of high attrition rates. Because dolomites are generally more reactive than calcites with both SO2 and H2S, a dolomite would be the feed material of choice for a chemically active fluid bed.

Jan 1, 1974

By Bernard J. Scheiner, R. J. Wesely, Cy E. Jordan, A. D. Zunkel, Gary M. Wilemon

The U.S. Bureau of Mines has investigated leaching of off-grade western United States phosphate deposits using sulfuric acid (H2SO4) in the presence of methanol. A combination of ore grinding followed by sulfuric acid in methanol leaching extracted over 80 pct of the phosphate. This leaching technique significantly limited the dissolution of iron, aluminum, and magnesium impurities and produced a phosphoric acid that was well within the desired limits for these impurities. The dissolution rate of phosphate rock in the sulfuric acid methanol system was significantly slower than the conventional aqueous sulfuric acid dissolution. Initially dissolution of the phosphate particle was controlled by the amount of surface area available to the sulfuric acid reactant. After about an hour of leaching, phosphate dissolution was slowed almost to a stop, limited by the rate of ion diffusion through the calcium sulfate barrier layer surrounding the unreacted phosphate particle. Consequently, the ore was ground below 38-pm to increase the particle surface area available and improve the overall dissolution kinetics and extraction. In addition, the sulfuric acid was slowly metered into the reactor to prevent any excess heat from the mixing of acid with the methanol from simulating the formation of methyl sulfates. The formation of methyl sulfate ultimately lowered the overall phosphate extraction by exhausting the supply of available sulfate ions for the dissolution reaction. Subsequent evaporation of the methanol from the product acid decomposed the methyl sulfates leaving undesirable sulfate ions in the product acid. Slow acid addition to the reactor provided high phosphate extraction and limited the amount of sulfate in the final product acid.

Jan 1, 1993

By J. O. Marsden

The 1980s saw a revolution in gold extraction technology, paralleled only by the implementation of the cyanide leaching process in the late 1800s. This revolution was led by the widespread adoption of carbon adsorption processes for gold recovery, heap leaching of low-grade ores and development of a variety of oxidation processes to treat refractory ores. In the late 1980s, gold production in almost all regions of the world increased, with the notable exception of South Africa. This geographical variety is creating a greater diversity of challenges for gold metallurgists. This is due to a wider range of ore types, new and varied environmental regulations and legislation, and a requirement to select the most appropriate technology to suit local needs. North America has led this technological revolution in the gold industry and is responsible for commercialization of most of the major innovations: carbon-in-pulp, heap leaching, whole ore pressure oxidation and whole ore roasting. Process selection trends A general trend in precious metals extraction technology has been the treatment of ores with progressively lower grades. The lowest cost treatment, dump leaching of material at run-of-mine size, has been increasingly applied. ZortmanLandusky, in Montana, is successfully leaching material above a cutoff grade of 0.2 g/t (0.006 oz/st) at an average rate of about 28 kt/d (31,000 stpd). At this scale of operation and in the absence of any cyanide-consuming species in the ore, process operating costs for a ge¬neric run-of-mine leaching operation are estimated to be between 60 and 75 cents/ t (66 and 77 cents/st). One of the largest heap leach opera¬tions treating crushed ore is the Round Mountain Mine in Nevada. It processes about 45 kt/d (49,000 stpd) at an average grade of 1.1 g/t (0.032 oz/st) at a nomi¬nal crush size of 80% -19 mm (-0.7 in.). Round Mountain also treats lower grade ore above a 0.2 g/t (0.006 oz/st) cutoff by dump leaching at run-of-mine size.

Jan 1, 1993

A Mineração da Trindade (Samitri) is a major Brazilian iron ore producer. Founded in 1939, privately owned Samitri operates six mines with a total production capacity of 14.5 Mt/a (16 million stpy). The mines are located in southeastern Brazil in the state of Minas Gerais. They are operating in the iron ore quadrangle, Brazil's primary iron ore-producing region. In addition to iron ore production, Samitri has the capability to produce 350 kt/a (386,000 stpy) of ferruginous manganese ore from two mines, also located in the iron ore quadrangle. Historically, about 70% of Samitri's production of lump ore, sinter feed and pellet feed is exported. Destinations include Belgium, Luxembourg, France, Germany, Trinidad and Tobago, China, Turkey and the United States. Alegria Mine In September 1989, Samitri started a new processing plant to treat itabirite, a low-grade iron ore. The goal of the plant was to produce sinter feed (coarse fraction) and pellet feed (fine fraction). Primary separation of sinter feed from pellet feed was accomplished with conventional vibrating screens making a 0.4-mm (40-mesh) cut. The screen oversize was stockpiled as sinter feed. The undersize was deslimed with hydrocyclones and upgraded by conventional froth flotation. Resulting pellet feed grades ranged from 3% to 3.5% Si02. A change in pellet feed requirements by Samarco Mineração SA, a Samitri subsidiary, called for Si02 levels below 1 % and increased production levels. Moreover, market demands called for a change in sinter feed size distributions. Unfortunately, lower pellet feed Si02 levels could not be achieved with the existing process. This was because of the presence of 35% +0.15 mm (+100 mesh) in flotation feed. Flowsheet development. Laboratory and pilot-plant studies conducted at Samitri's research facility found that to achieve lower Si02 levels, the +0.15 mm (+100 mesh) in flotation feed must be kept below 5% to 10%.

Jan 1, 1997

By James W. Babcock

Introduction Geologic ore deposit models are key to any exploration program. In the search for ore deposits, the geologist first tries to understand the genesis of known ore bodies. During reconnaissance and evaluation of a prospect, a valid exploration model of a known ore body can help the explorationist focus on critical geologic attributes of the target area. Exploration models can conserve exploration funds that might otherwise be spent collecting data not critical to delineating an ore body. This article examines the benefits of using models, factors to be considered in developing models, and examples of the way recent models have evolved. New exploration concepts and techniques are developed in response to increased competition in the mining industry. New techniques can give an exploration group a slight edge that may translate into a discovery. Mine geology staffs may find previously unlooked for extensions to the ore body by applying new genetic concepts. When all appropriate techniques are applied to exploration and mining efforts, greater efficiency and increased profits may result. Before the 1950s, scientists speculated on the genesis of ore deposits and other natural phenomena. But they presented their results as if universal and final, even though they applied to only a few deposits. Because it did not provide sufficient criteria to distinguish the genetic processes, the classic conflict between hydrothermalists, epitomized by Lindgren, and nonhydrothermalists did not help the minerals explorationist much. Important information about individual ore deposits, such as age of the host rocks and mineralization, composition of the mineralizing fluids, and separation of mineralizing and nonmineralizing events in the paragenetic sequence, could not be gathered with past equipment and methods. But these early concepts of ore genesis contained excellent empirical observations, perhaps the most useful parts of these hypotheses. Through the years, prospectors have found most of the ore deposits in the world using direct observations and their collective empirical wisdom - an empirical model. The geologist's contribution becomes increasingly important after the more obvious surficial ore deposits have been discovered. In Europe and North America that time has arrived. With the introduction of sophisticated equipment and matching techniques in the 1950s in geochronology, geochemistry, geophysics, remote sensing, and computers, many previously equivocal genetic questions can be resolved. This proliferation of highly technical data has allowed the construction of many well-founded genetic models.

Jan 12, 1984

By George J. Dvorznak, Robert W. Waytulonis

The Bureau of Mines is conducting a research project in cooperation with the Mine Safety and Health Administration (MSHA). Mining companies, and equipment manufacturers are also participating through the Colorado Mining Association (CMA). The objectives of this cooperative research project are to determine the practicality of coupling a dry exhaust conditioning system (dry system) and diesel particulate filter (DPF) to make an integrated control system, and to determine the effectiveness and durability of the integrated system in an underground coal mine. Diesel-powered mining machines must be equipped with control devices to reduce surface and exhaust temperatures to safe levels and prevent flames and sparks from being emitted to the mine atmosphere. Diesel exhaust-gas water scrubbers have been successfully used for many years but they have several disadvantages; they are large, consume large quantities of water, and require frequent maintenance to remain functional. Additionally, diesel exhaust is a source of noxious gases and particulate matter. Particulate emissions are composed primarily of small carbon particles with absorbed hydrocarbons and they are almost entirely respirable in size. Even an engine in good mechanical condition can emit up to 400 mg/cu m of respirable particulate matter. A dry system for control of diesel fire and explosion hazards, coupled to a DPF, promises to be a complete control system for diesel engines. The dry system cools the exhaust and suppresses sparks and flame with a heat exchanger and flame and spark traps. The conditioner is smaller, consumes no water, and requires less maintenance than a comparable water scrubber. The DPF uses a ceramic substrate as a wall-flow filter and is very efficient at collecting exhaust particles. Average particulate mass collection efficiency is 90%. This report describes a cooperative research project to combine the dry system with the DPF, conduct performance tests on the integrated system at Bureau and MSHA 1aboratory facilities, and conduct field tests of the system on a production machine in an underground coal mine.

Jan 1, 1987

By David A. Lindsey

The world-famous beryllium deposits at Spor Mountain, northwest of Delta, Utah, are the principal resource of beryllium in the United States. Beryllium metal, beryllium-metal alloys, and beryllium oxide ceramics have a long history of specialty applications. Beryllium is used in X-ray windows, nuclear reactors: and a wide variety of industrial and electronic products. The Spor Mountain deposits are located on the western rim of the Thomas caldera, one of at least three volcanic depressions that subsided during voluminous eruption of rhyolitic ash-flow tuff in early Oligocene time. Beginning in early Miocene time, the caldera rim and its volcanic fill were cut extensively by basin-and-range faults. Basin-and-range faulting was accompanied by local eruption of high-silica rhyolite. High-silica topaz rhyolites at Spor Mountain (21 Ma) and Topaz Mountain (6 to 7 Ma) are especially rich in fluorine and lithophile trace elements such as beryllium. Topaz rhyolite of the Miocene Spor Mountain Formation, or its magma was the source of the Spor Mountain beryllium deposits. At Spor Mountain, deposits of beryllium, as submicroscopic bertrandite, Be4Si207(OH)2, occur in rhyolite tuff beneath flows and domes of topaz rhyolite. The beryllium deposits also contain minor disseminated fluorite, lithium, uranium, and anomalous traces of other lithophile elements. The host tuff, originally composed of glass, zeolite, and abundant clasts of carbonate rock, has been altered to clay and potassium feldspar. Fluorite, quartz, and opal replaced carbonate clasts in the tuff. Beryllium was deposited with fluorite in altered clasts and in the matrix of altered tuff. Fluorspar and uranium deposits are spatially and genetically associated with the beryllium deposits at Spor Mountain. Fluorspar deposits at Spor Mountain occur mostly in breccia pipes. Some fluorspar pipes contain uranium, thought to be dispersed in the structure of fluorite. Secondary uranium minerals are dispersed throughout the tuff that hosts beryllium deposits and comprise lenses of ore-grade uranium at the Yellow Chief mine.

Jan 1, 2001

By M. P. Evans, Rainer Kahrger

During the last decade or so great advances were made in the solvent extraction, electro winning technologies. They, combined with heap leaching, made it viable to exploit large, relatively low grade oxide copper deposits. The El Abra mine is a good example for such a deposit. Situated in Northern Chile at an elevation of about 4000m (14000 feet), 70 krn north of Calama, the El Abra deposit has been known for many years. In the early 1990's Codelco decided to sell a major holding in the deposit to international mining companies. After lengthy negotiations Cyprus Minerals finalized in June 1994 the purchase of 51% of the deposit with Codelco retaining the balance. lance. Already in 1993 Cyprus and the engineer on the project, began discussions with international materials handling companies with regards to the materials handling system required for the project. These early discussions were considered critical for this fast track project. Immediately after the notice to proceed with the project, several companies were invited to submit competitive conceptual proposals for that portion of the material handling system which was to transport crushed and treated ore from the plant to the leach pad and build the leaching heaps at a rate of up to 150 000 tons per day. A supplier was selected. Additional studies were made for the conveyor system from the mine to the fine crushing plant. Due to the extremely rugged terrain and high altitude at the mine, a decision was made to locate the plant and the leaching operations 15 km east of the mine at an elevation of 3400m. In July 1994 the supplier started the conceptual engineering with a design team at the engineer's San Francisco office. The undertaking was unique in the sense that the supplier's engineering team was integrated into the project for the duration of the conceptual engineering. The open and continuous communication greatly contributed to the success of the design work.

Jan 1, 1996

INTRODUCTION The role of comminution and related unit operations in mineral processing applications is of major importance. This is especially true in terms of operating costs, since these unit operations represent the major fraction of the overall processing costs. Due to the broad scope and the large number of unit processes and machines involved, Section 3 is divided into five subsections. In Section 3A, General Aspects of Comminution, topics covered include history, terminology, particle¬size distributions, classes of comminution machines, testing and calcu¬lation procedures, and simulation and modeling. In Section 3B, Crush¬ing. the subjects include jaw crushers, gyratory crushers, cone crushers, hammermills, and impactors. The chapters of Section 3C, Grinding, cover aspects common to tumbling mills, ball mills, rod mills, autogenous mills, pebble mills, roller mills, fluid energy mills, other types of grinding machines, and grinding costs. Section 3D, Classification, coverage includes classification theory, hydrocyclones, and mechanical classifiers, and in Section 3E, Screening, the topics presented are classes of screens, selection of vibrating screens, sieve bend screens, and screening media. About five years after the Handbook was begun, Section 3 was unfortunately without an editor or contributors for over half of the chapters. A committee was then organized to expedite completion of the section. When this committee contacted the persons who had agreed to contribute to the section, it was found that many of them wished to resign from their earlier voluntary obligation to AIME. Therefore the committee had to find new contributors for these chap¬ters in addition to other chapters in Section 3. Since there had been no previous effort to locate contributors for Air Classification, Dust Collection, and Washing and Scrubbing, it was agreed to delete these subsections. In Section 3, equipment availability, capacity, and performance data from various manufacturers and users are provided for engineer¬ing use. Selected data from existing installations are also included. The machines that are being used in comminution, classification, and screening are described in detail, and drawings, photographs, and diagrams are presented to supplement the descriptive material. The editors thank and acknowledge the generous effort of the many contributors, some of whom were called upon five or more years after the Handbook was started. It is regretted that Fred C. Bond, who was a member of the committee formed to complete this section, was deceased before the section was finished. During the time that he worked with the committee, he contributed a great deal as an author and councilor.

Jan 1, 1985

By H. Maleki, G. Tetreault

This study was initiated by the US Bureau of Land Management (BLM) to develop guidelines for determining the maximum economic recovery of resources in coal mines. The work was in response to a requirement in the Mineral Leasing Act of 1920 and Federal regulations. The intent was to address the economic rainability of small, irregular reserves in existing longwall mines. In particular, there was a need to determine if room- and-pillar mining using a continuous miner (CM) was economically sound or whether unconventional (short or odd-shaped) longwalls could be used to recover small coal reserves economically. Small reserves, called "widgets " are left in longwall mines on one side of the mains near outcrops and adverse geological conditions or near any other location where reserve geometry does not lend itself to mining with a rectangular longwall panel. The work included the analysis of the geologic, geotechnical and economic factors that influence the recovery of small coal reserves; the analysis of historic changes in supply, demand and coal prices; the development of typical cost models for room-and-pillar and longwall mines; and the development of a practical methodology for determining maximum economic recovery. The methodology included an evaluation of the ratio of coal mined during longwall mining to that mined for development (LDR), as well as costs of maintaining coal quality depending on market conditions. The LDR is a good indicator of mine efficiency and overall coal recovery in modern longwall mines and, thus, is used to evaluate the increased costs associated with adding new development sections for extraction of small reserves. The study examines the economic feasibility of using unconventional longwalls for the recovery of medium-sized reserves, depending on site-specific geologic and geometric conditions.

Jan 1, 2002

By Robert S. Ondrey, Robert A. Haney, Kenneth G. Fields

As part of an MSHA program to assess the effectiveness of dust control parameters for longwall mining operations, respirable dust studies were conducted on six longwall sections. The purpose of these studies was to evaluate the influence of airflow and production on longwall dust control. The sections were sampled for 3 to 35 shifts. In addition to dust, ventilation and production measurements, other dust control and operational parameters were measured. The water spray system at each operation conformed with generally recommended practices. Therefore, improvements to the dust control system would be most appropriately achieved through improvements to ventilation along the face. Two methods of assessing the influence of ventilation and production were used. For two of the six mines where extensive sampling (22 and 35 shifts) was conducted, multiple linear regressions were used to relate the dust concentration versus airflow and production data. For these two mines, statistically significant correlations existed between concentration and both production and airflow. The multiple regressions fit to the data indicated that for every 0.47 m3/s (1,000 cfm) increase in airflow, there would be approximately 0.04 to 0.07 mg/m3 reduction in dust concentration; and, for every 1,000 ton increase in production, there would be approximately 0.15 to 0.50 mg/m3 increase in dust concentration. For the four mines with limited data (3 to 10 shifts), as well as for the two mines with extensive sampling, an average ratio of airflow per ton of coal mined was calculated by proportioning the airflow to production and the designated occupation personal respirable dust exposure to a 2.0 mg/m3 concentration. The airflow-to-tons ratio required to maintain a 2.0 mg/m3 dust concentration ranged from 0.0038 0.0071 m3/s per ton (8 to 15 cfm/ton). Both of these data treatments were used to calculate airflow requirements based on normal production rates. For the two mines where both the regression and airflow-to-tons ratio were calculated, results from the two methods agreed within 25 percent.

Jan 1, 1993

By V. Castranova, L. Wu, K. Van Dyke, J. Gutierrez, V. Vallayathan

Since it has been demonstrated that silica caused phagocytic cells to activate lipoxygenase metabolism of unsaturated fatty acids we thought selective inhibition of this metabolic pathway might be helpful in treatment of silicosis. It is known that lipoxygenase metabolism plays a role in the pathogenesis of a variety of inflammatory and hypersensitivity conditions. Further, it is believed that the alveolar phagocytic cells which engulf silica begin the inflammatory cycle which produces the metabolic products, cytokines and growth factors which causes fibrosis in the lung. There have been indications that drugs which inhibit lipoxygenase can inhibit fibrosis from other causes. Previously, we developed a method which detects the activity of lipoxygenase metabolism by measuring free radical oxidation via light production or chemiluminescence (CL). We decided to apply this method to phagocytic cells that would be found in the lung in the presence of silica with and without newly developed inhibitors of the lipoxygenase reaction. We used drugs which inhibit lipoxygenase directly including AA861 (TAKEDA), A63162 (Abbott), and an inhibitor that scavenges free radicals produced from the lipoxygenase reaction, nordihydroguairetic acid. In addition we used an indirect inhibitor, tetrandrine. We found drug inhibition of silica activated CL from alveolar macrophages, neutrophils and human leukemia (HL-60) cells differentiated with DMSO. Nordihydroguairetic acid 2x10-5M produced almost complete inhibition in all three cell types. In human leukemia cells (HL-60) A63162 and tetrandrine were equally inhibitory at 42% while in human neutrophils A63162 and tetrandrine were less active 22 and 10% respectively. In macrophages A63162 and AA861 were less than 50% inhibitory to cellular CL at 2xl0-5M. Direct assay of tetrandrine (2x10-5M) with sodium arachidonate and soybean lipoxygenase reveals no inhibition. All antilipoxygenase drugs regardless of mechanism were inhibitory to cellular chemiluminescence from all three types of phagocytic cells. These drugs alone or in mixtures could prove useful in treatment of silicosis.

Jan 1, 1991

By R. C. Dunne, C. T. O'Connor

Flotation practice on eighteen South African flotation plants is described. The plants are categorized as those treating reclaimed tailings, those treating material which has already been subjected to cyanidation or uranium leaching, and those treating milled ore. The similarities and differences are highlighted.

Jan 1, 1998