Search Documents

By B Scheiner, D. A. Stanley

Introduction Treatment of ores to recover metal and mineral values results in waste materials usually in the form of dilute slurries. The US Bureau of Mines (USBM) investigated a technique for dewatering phosphatic clay waste by flocculating with polyethylene oxide (PEO) and dewatering the resulting floes on a static screen and/or trommel screen (Schemer et al., 1985). In the investigation, it was determined that PEO was far superior to polyacrylamide polymers for this type of dewatering. This paper discusses reasons for this superior performance. Comparison of PEO with polyacrylamides Dewatering experiments were conducted by adding PEO solution from a burette to a stirred clay slurry. The dewatering endpoint was characterized by rotation of the floc mass as a unit, a clear supernate, a maximum floc size, and a minimum floc volume. Additional water was removed from the floes by hand squeezing (Schemer et al., 1985). The clays investigated were sodium, potassium, magnesium, calcium, and aluminum exchanged montmorillonite and attapulgite. Nine commercially available (Superfloc) polyacrylamides were compared with PEO at two polymer concentrations. Results are summarized in Table 1. The solids content of the dewatered clays ranged between 24% and 33% and was highest for PEO-treated material. These results and the data in Table 1 indicate that PEO is superior to polyacrylamide in terms of polymer dosage required. Superflocs 16 through 128, like PEO, are nonionic and should give similar results to those for PEO if the flocculation mechanism is the same for both type polymers. Superflocs 204 through 214 are anionic with increasing anionic character from 204 to 214. Generally, the anionic polymers gave the best results for the polyacrylamides tested, but in terms of dosage they were not as good as PEO. Correlation between flocculation and dewaterability of waste slurries The overall mechanism for mechanically induced clay dewatering is not completely known, but certain observations can be made. For instance, when a polymer is adsorbed on a clay such as montmorillonite, the polymer desorbs interlayer water. Polymer adsorption is driven by favorable entropy changes associated with this water desorption. It is also known that the -CH2-CH2- links of the PEO chain are sufficiently hydrophobic to lead to physical adsorption of the polymer (Theng, 1979). For montmorillonite slurries, the sheet-like fundamental particles, called tactoids, consist of a small, variable number of aluminosilicate layers together with interlayer water and exchange ions. The flocculation process consists of adsorption of polymer on the tactoid. Loops and tails of polymer that extend into solution then adsorb on another tactoid, forming a bridge. Mechanical action, induced by hand squeezing or in a trammel, joins the bridged tactoids face-to-face and edge-to-edge to form regions of high density. Similar orientation effects are observed for the needle-like attapulgite crystals (Schemer et al., 1985). Proposed flocculation model Generally, statements concerning flocculation and dewaterability apply to both PEO and the polyacrylamides. However, PEO has additional interaction with the clay material when compared with polyacrylamides. PEO is a polymer with repeating -CH2-CH2-O- groups and interacts with montmorillonite through a water bridge whose strength is greatly influenced by the exchange ion. To obtain insight into this interaction, a series of experiments were conducted in which different ion exchange forms of montmorillonite and attapulgite clays

Jan 1, 1987

By C. J. Dungey

INTRODUCTION The County of Cornwall is situated in the South Western extremity of England, see Fig. 1, and has for hundreds of years been an historical centre of mining activity. In the last century many thousands of Cornish miners emigrated to Canada, U.S.A., Australia and numerous other countries throughout the world to form the nucleii of mining industries in those lands. At present there are four active underground mines within the county, all mining tin, together with a relatively large china clay industry. All the operations are directly or indirectly associated with the three main granite intrusions, namely the Land's End Granite, the Carnmenellis Granite and the Bodmin Moor Granite. The report which follows relates to two mines, owned by the South Crafty Group of Companies, namely the South Crofty Mine itself and its smaller subsidiary, Wheal Pendarves. Both these mines are adjacent to the Carn Brea Granite ridge, see Fig. 2, which is an off-shoot of the main Carnmenellis Granite mass. The Carn Brea Granite has provided one of the most intensive areas of copper and tin mineralisation anywhere in the world. Many of the mines worked during the last two centuries and the early part of this century were situated close to the metamorphic aureole surrounding the granite intrusion. Both South Crofty and Wheal Pendarves have their shafts collared in the overlying slate, locally known as killas, but the major part of their workings are in the granite beneath. The ore bodies, or lodes, of both mines are generally steeply dipping and approximately one to four metres in width. They have been, and continue to be, worked by either back or under-hand stoping with the major level interval being approximately 37 metres. A feature of both stoping systems is that they require no back filling and in many cases the completed working areas have remained open for many years due to the competent wall rock conditions. The stoping operation necessitates having box-holes or draw points at regular intervals along the strike length at 4 to 7 metres centres; thus a stope some 50 metres long may typically have ten box-holes or draw points through which air can percolate into the empty stopes above. The granite country rock contains traces of uranium minerals, namely pitchblende or uraninite, and it is the decay of this uranium mineral which leads to the formation of the mobile radon gas which, together with its short lived daughters, may create a hazard. The presence of uranium minerals has long been known, but the quantities being so minute, it was not appreciated until some ten to fifteen years ago that these might present a hazard. The Mines and Quarries Inspectorate approached Management approximately ten years ago with a view to taking samples in areas of the mine that they felt might contain the highest concentrations of radon. Samples were thus taken in several areas of both mines, normally well away from working areas and where there was no through ventilation. The results of these initial tests were published by the National Radiological Protection Board in a paper entitled "Radon and Its Daughters in Various British Mines". The results of the initial surveys made it apparent that improved ventilation was the most important factor in reducing radon daughter concentrations within the mine atmosphere, with increased flow rates having three beneficial functions, viz. (1) To dilute radon daughter concentrations. (2) To prevent radon and its daughters reaching a state of equilibrium. It is not uncommon for radon and its daughters to have a disequilibrium factor of 1,000 in some uranium mines.

Jan 1, 1981

By Jacques H. Nantel, James F. Archibald

INTRODUCTION The use of backfill materials in underground mines has been practiced for many years and the trend indicates an increased utilization of backfill materials in the future. The authors believe that underground uranium mines will follow this trend. Classified mill tailings, approximately 65 to 70 percent solids by weight, are the most common fill materials. Cement or other pozzolanic agents can be added to the fill materials to improve their strength characteristics. Dry fill, in the form of development muck, can also be introduced in the stopes to fill the voids left by the action of mining the ore. This paper deals mainly with the assessment of the radiation properties of backfill materials originating from uranium ores processed in the milling facilities of uranium mines. The paper outlines the results of studies conducted in the laboratory and in the field on radon emanating characteristics of backfill materials utilized in uranium mines. ROLE OF BACKFILL IN UNDERGROUND MINES Fill is a structural component of any underground mining system. In general terms, the purpose of filling is to provide ground support, to make recovery of pillars possible to provide a working platform for men and equipment, and to allow for waste disposal. There are other inherent advantages to the use of backfill underground, the most important being to: a) permit mining at greater depth b) allow the adoption of highly mechanized mining techniques c) reduce dilution from wall sloughing d) minimize roof and wall failures e) allow the mining of irregular orebodies, and f) to provide better control of ventilation. The last item is of great importance to uranium mine operators. The introduction of radioactive backfill underground represents an additional source of radioactive contamination; on the other hand the introduction of backfill in the mine reduces the volumes of workings to be ventilated. As a consequence the general mine ventilation is more effective and in most cases, better air quality can be maintained in the mine. There are of course some disadvantages associated with the use of hydraulic fills in underground mines, notably: a) the handling of large additional quantities of water from the underground workings b) delays caused by the cyclical nature of the backfilling operations c) additional costs associated with stope preparation and placement of backfill in stopes, and d) "spills" caused by bursting pipes or fill escaping from fill retaining structures. ASSESSMENT OF NON-RADIOACTIVE PROPERTIES Although the radioactive properties of mine backfills are discussed in this paper many other physical and chemical properties of backfills must also be considered. These properties include: a) percolation rate and permeability parameters b) viscosity versus pulp density relationships c) size analyses d) settling times e) settled bulk density f) solids specific gravity g) void ratio and porosity h) optimal percentage solids by weight i) specific gravity of slurry j) addition of cement:cement retention and loss k) unconfined compressive strength 1) triaxial compressive strength m) shear strength (non-cemented)

Jan 1, 1981

By J. A. Brierley, S. R. Hutchins, C. L. Brierley

Introduction Many gold and silver ores are refractory to conventional processing technologies. Thus, precious metals recovery is uneconomic. These resources can consist of ores, flotation concentrates, mill tailings, and other reserves. The refractory nature of these materials can be ascribed to such components as iron sulfide minerals, silica minerals, tellurides, organic compounds, and sulfosalts. Precious metals locked within iron sulfide minerals account for a large number of refractory gold ores. These minerals consist principally of pyrite or arsenopyrite. They must be oxidized to liberate the encapsulated precious metal and allow its contact with the leaching agent. Carbonaceous gold ores represent a unique class of refractory precious metal ores in general. Not only does gold encapsulation by iron sulfide minerals occur (Hausen, 1985), but these ores also contain organic matter that interferes with gold recovery by cyanidation. Direct interference can be attributed to either occlusion of gold within organic matter or formation of a stable gold-carbon complex. The magnitude of this problem is debatable. Wells and Mullens (1973) examined two carbonaceous gold ores and found no association between the gold and carbonaceous material. A more common problem is indirect interference, whereby the aurocyanide complex formed during cyanidation is sorbed by the native organic matter and is not available for recovery. This phenomenon is referred to as "preg robbing" (Osseo-Asare et al., 1984; Hausen and Bucknam, 1984). Guay (1981) summarized various methods that can reduce preg robbing during processing of carbonaceous gold ores. However, some are not applicable to carbonaceous ores that have significant amounts of gold locked in iron sulfide minerals. Several methods exist for oxidizing iron sulfide minerals and rendering refractory precious metal ore amenable to conventional recovery processes. These include various embodiments of roasting (Jha and Kramer, 1984; Brown, 1984; Arriagada and Os-seo-Asare, 1984; Smith, 1986), pressure oxidation (Muir et al., 1984; Beattie et al., 1985; Thompson, 1986; Weir et al., 1986; Argall, 1986), and chemical oxidation (Scheiner, 1971; Jackson, 1983; Van Weert et al., 1986). Each process has been successfully used for refractory precious metal ores. In many instances, however, their use is precluded by capital and operating costs relative to the value of the ore. An alternative to these methods is microbial pretreatment - a biological process whereby iron sulfide minerals are degraded and the liberated precious metal values can be recovered by conventional technologies. Bioleaching refractory precious metal ores is a relatively new concept compared to roasting and chemical oxidation. It is rapidly becoming established as a viable pretreatment alternative. Numerous studies have been conducted in the laboratory and on a pilot scale (Yudina et al., 1979; Lawrence and Bruynesteyn, 1983; Pol 'kin et al., 1985; Marchant, 1985; Livesey-Goldblatt, 1985; Gibbs et al., 1986). Comparative tests have demonstrated that bioleaching can be equal to or better than roasting or pressure oxidation in terms of product recovery and process economics (Fridman and Savari, 1983; Livesy-Goldblatt et al., 1983; Karavaiko et al., 1985; Gilbert et al., 1986; Hackl et al., 1986). Bioleaching's main drawback is that pretreatment requires days rather than hours. This can lead to excessive operating costs for difficult-to-treat ores. In all of the tests reported thus far, the leaching microorganism used has been thiobacillus ferro-

Jan 4, 1988

By Kenneth K. Humphreys

INTRODUCTION At the time the 4th edition of this book was published in 1979, the coal industry had experienced a sharp upturn in prices for its product. From 1950 throgh 1969, steam coal prices had held almost flat at about $5 US per st (about $5.50/t). Thus, when considering the effects of inflation, the price of coal had actually been declining for two decades. The passage of the Coal Mine Health and Safety Act in 1969 and its cost effects started an upward trend in coal prices which was rapidly accelerated by the effects of the Mid-East oil embargo in 1972. Prices of steam coal on the spot market eventually climbed to over $30 US per st ($33/t) and higher in some cases. Metallurgical coal prices skyrocketed in a similar manner and the industry at long last appeared assured of an adequate return on investment. Many companies did expend large sums of money to upgrade and expand their mining and preparation facilities. Unfortunately the bubble eventually burst, in great measure due to the downturn in the US domestic steel industry and the resultant decline in metallurgical coal demand, loss of export markets to other nations and even imports of large amounts of foreign coal to the United States, and more stringent environmental regulations which made many high sulfur coal measures uneconomical to mine. Compounding the problem was the rapid world decline in oil prices in the mid-1980s which encouraged many consumers to utilize oil rather than coal. During the 1980s, metallurgical coal dropped over 20% in price, which, when considering inflation, actually amounted to about a 40% decrease in value. Export coal decreased a similar amount in price. Steam coal prices held nearly constant, thus also losing considerable value when inflation is considered. All of these factors make it even more imperative than ever that the industry do everything in its power to make wise economic decisions and to examine carefully all existing operations and planned future expenditures to be certain that their full cost implications are understood and that they can be justified on the basis of an adequate return on investment. It cannot be assumed that the price of coal will increase. To the contrary, as indicated previously, when considering inflation, coal decreased in value in the 1980s, just as it also did in the 1950s and 1960s. The price surges in the 1970s merely were a catchup game, and in truth the true market value of coal is in reality even lower than it was in 1950. CAPITAL AND OPERATING COST ESTIMATION Prior to constructing a new plant or expanding existing facilities, a detailed preliminary cost estimate is necessary to determine the capital investment

Jan 1, 1991

By Yanchuan Li, Haifei Yao, Haiyan Wang

"Dust pollution is very serious in coal mining process, which is a great threat to the underground staff health and equipment and facilities safety. Coal seam water injection in mining process is an effective way to reduce coal mine dust concentration at the source. However, the effectiveness of water injection is limited in high-pressure and low-porosity coal seam. To improve the moisture content of coal seam, expand the wetting range and enhance the effect of dust reduction by water injection, the injectability and influencing factors of coal water injection are analyzed by numerical simulation method, and the sealing technology under high-pressure condition is studied. Then, according to the practical conditions of Tangkou coal mine, the parameters and process system of process system are designed, the effect of high-pressure water injection in coal seam was determined by testing water injection quantity, water increment and dust concentration. It is showed that the dust-removal rate of the high dust concentration operation such as falling coal and moving frame is 63.49% and 59.72%, the maximum dust-removal rate of multi-processes is 53%, which achieve a high level of application. The research results in this paper is of important theoretical and practical value to improve the water injection effect of high-pressure and low-porosity coal seam and improve the efficiency of dust removal in coal mining process.Introduction With the increasing of the depth and mechanization of coal mining, coal dust, the impact of ground pressure, ground temperature and other natural disasters continue to upgrade the harm degree (Wang 2011, Wu et al 2012), disaster incidents occur frequently, which seriouslythreaten the safe and efficient mining and the physical and mental health of underground staff. Coal seam water injection can effectively reduce the coal dust when coal crushing, prevent the impact of mine pressure, coal and gas outburst disasters, by increasing the thermal conductivity of coal, reduce coal temperature, and prevent spontaneous combustion of coal. In addition, coal seam water can soften the hard coal, so that speed up the recovery rate, improve coal production and efficiency (Wu et al 2008, Nie et al 2007). However, the coal seam in many mining area is with high-pressure and low-porosity feature, Coal joint cracks are not developed and relatively hard, water injection is difficult in these coal seams, then the desired disaster prevention effect cannot be achieved (Jin et al 2001, Zhao et al 2000). In this paper, the numerical simulation and field test methods are used to design the high-pressure and low-porosity coal seam water injection technology, so as to solve the difficult problem of coal dust control in high-pressure and low-porosity in deep well mining process."

Jan 1, 2017

By Changwoo Lee, Jan M. Mutmansky

Introduction Recognition of Coal Workers' Pneumoconiosis (CWP) as a major occupational disease has affected various aspects of the coal mining industry in the United States as well as in almost all major coal producing countries. Regulations related to the control of coal mine dust forced mine operators to modify their mining and ventilation practices. As the coal production record of the last 15 years shows, this had both direct and indirect impacts on the productivity and production costs. To identify the causes of CWP, many research efforts have been made through- out the world. Most of these studies were epidemiological in nature, attempting to pinpoint exposure and seam variables that affected the incidence of the disease. Other studies have been oriented toward the elemental and mineralogical composition of the coal dust in the mine atmosphere and in the miners' lungs. These studies indicate that there may exist some relationships between the characteristics of the coal mine dust and the prevalence of the disease. Some of the variables that are thought to affect the occurrence of CWP are the mass of the dust in the working place, the rank of the coal, the existence of certain trace elements, the free silica content of the coal, and the existence of other minerals in the respirable dust. A more complete description of these previous re- search studies has appeared elsewhere (Mutmansky and Lee, 1984). The behavior of particles in the human lung is known to be governed by their aerodynamic diameter, which is defined as the diameter of a hypothetical spherical particle with unit density that exhibits the same settling velocity as the given particle. Because of this fact, the aerodynamic size distribution of coal mine dust is one of the parameters to be determined along with the other physical, elemental, and mineralogical characteristics. The objective of this paper is to establish a strategy for providing coal mine respirable dust samples for characterization purposes using instruments that classify according to the aerodynamic diameter. In addition, several findings concerning characterization methods will be presented. Choice of Samplers Most of the gravimetric dust collection devices that can be utilized in a mine environment can be

Jan 1, 1986

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

It is imperative that the hydrogeologic frame- work and the ground water flow systems of a Potential mine area be investigated prior to initiation of mining. Such investigations are necessary so that potential mine water inflow problems can be anticipated and controlled. Obvious difficulties can arise if large inflows of ground water occur in underground workings. Costs of water removal and disposal, if not foreseen and included in economic planning, can severely limit or eliminate profit from a mining operation. Safety problems associated with large inflows are an additional potential problem. The inflow of water into a mine necessarily alters the associated ground water system. The inflow also may impact nearby surface water regimes, depending upon the interaction of the surface water and ground water systems. The inflow of water into a mine inevitably causes a decline in the ground water levels in the vicinity of the mine. This decline may be restricted to a small area or it may extend a considerable distance, depending upon the hydrogeologic properties of the associated hydrostratigraphic units. A decrease in surface flow will result if the area of ground water level decline intersects a stream or spring that is hydraulically connected to the ground water system. Mine inflow problems historically have been evaluated after-the-fact. Premining hydrologic investigations only recently have been initiated. Brown's (1977)* report on anticipated hydrologic impacts of oil shale mining in the Piceance Basin of Colorado is an example of premining hydrologic planning. Observed difficulties inherent in designing a data collection network and then utilizing the data to predict mine inflow have led us to the preparation of this manuscript. This manuscript reflects a two-phase effort. The first phase describes and develops analytical and numerical techniques for mine inflow prediction. Emphasis in this section is placed on the selection and application of data collection techniques and data analysis procedures. The second phase applies the prediction technique(s) developed during phase 1 to two existing mines. The objective of phase 1 efforts is to evaluate the hydrologic variables associated with surface water systems and ground water systems that can affect the inflow of water into an underground mine. Subsequently these variables are incorporated into predictive techniques for estimating underground mine water inflow and its effect on associated ground water and surface water systems. The specific objectives of phases 1 and 2 are to: 1) Determine the hydrologic parameters required for predicting underground mine water in- flow and the potential effects of the inflow on surface and ground water systems. The hydrologic parameters represent both premining and past initiation conditions. 2) Outline methods for obtaining the necessary input data for the predictive techniques in pre- mining and post initiation periods. 3) Present existing numerical techniques for predicting underground mine water inflow including assumptions Ad required input. 4) Evaluate existing numerical techniques previously tabulated based on their applicability to mine water inflow prediction. 5) Attempt to develop analytical techniques for predicting underground mine water inflow. 6) Develop, through modification of existing models, a general mathematical model as a numerical technique for predicting underground mine water inflow and the resultant effects on surface and ground water systems. 7) Apply the predictive techniques to two existing mines selected for this purpose. 8) Compare the predicted inflow rates to measured inflow rates at both mines. 9) Compare predicted impact on district hydrology to observed impacts where possible. 10) Evaluate the predictive technique.

Jan 1, 1986

By Bruce D. McCellan

INTRODUCTION The gathering arm loader was patented by Joseph Joy in 1916. This unique machine motion became the standard of the industry and is used on underground loaders and continuous miners throughout the world. Figs. 1 and 2 show two types of gathering arm loaders. The gathering arm loader is a crawler-mounted ma¬chine primarily used for loading coal in a conventional mining system. Other uses also have been found for this machine in noncoal mines and other industries. MECHANICAL ASSEMBLIES The front or loading end of the machine, commonly called the head, consists of a tapered structural frame, hinged at the rear to the chassis and riding the ground at the front. Two bevel-gear cases are mounted in the head. They are connected by a timing shaft, which also acts as a conveyor drive shaft on most models. An eccentric disk attached to each gear case drives the gathering arms. The rear of the arms are attached to a swivel assembly. The motion derived from this arrange¬ment gathers loose material from the ground directly in front of the machine and loads it into the conveyor. Power for this drive is provided by two electric motors mounted under the gathering head. A speed reducer attached to each motor provides a gathering arm speed of approximately 5.2 rad/s (50 rpm). A torque limiting clutch is provided on each reducer to guard the system against sudden impact loading and continual overloading of the motors. The conveyor consists of an open box section through which a universal-type chain carries the ma¬terial to the rear of the machine, where it is discharged into the haulage vehicle. The chain is driven by a sprocket located on the timing shaft between the two gathering-head bevel-gear cases. On some large loader designs, primarily for noncoal applications, the chain is driven by a separate gear motor at the discharge end of the conveyor. However, the system driven by the timing shaft is used most widely. The conveyor frame is hinged just to the rear of the gathering head. It can be raised or lowered by hydraulic cylinders to the desired discharge height. The conveyor frame also is designed to pivot 0.79 rad (45°) either side of the center, just to the rear of the chassis. This feature increases the maneuverability of the ma¬chine and makes it possible to discharge material into the haulage system when in tight quarters such as when turning a crosscut. This function also is controlled by a hydraulic cylinder. The chassis of the loader consists of two crawler frames and cross members, holding the frames in position. The frames are either welded or cast as¬semblies. Replaceable wear runners are provided on the frames to take the wear generated by the crawler chain. An adjustable take-up idler keeps the crawler chain in proper adjustment for maximum life. The drive system for the crawler chains varies with the manufacturer, but it generally is one of two basic designs. One system provides a traction motor for each side of the machine, coupled to a speed reducer. A spur and bevel-gear train transfers power to the sprocket, which drives the crawler chain. Directional control is achieved by disk-type clutches. The other system also uses a motor for each crawler, coupled to a speed reducer. A roller chain drives the sprocket, which in

Jan 1, 1982

By A. P. Cook

Methane drainage on a mine-wide scale is a relatively new technology to South African coal mines. Shallow seams and apparently low methane contents have been assumed to result in less methane problems than experienced in other countries. The introduction of deeper mines however, has now resulted in methane drainage taking on a higher priority. Methane contents in the region of 12 m3\t have resulted in one colliery introducing drainage as a ventilation support. Although a low seam permeability initially indicated reduced potential for drainage, early borehole flows of 90 m3\m\year have since increased to 450 m3\m\year. Rapid inflow of methane into goafs and sealed areas from seams surrounding the main production seam at another colliery have warranted extensive evaluation of the methane properties of these seams with the projected introduction of predrainage from surface. Methane pressures in excess of 1000 kPa and contents in the region of 10 m3\t again give methane volumes suitable for drainage. Coal seam drainage ahead of mining is becoming more significant and is likely to see an increase in the near future. INTRODUCTION Methane gas is an everpresent hazard associated with underground coal mining. Safe working levels of methane in the mine atmosphere are normally maintained by ventilation practises, ensuring sufficient dilution of the gas. However in some cases the ventilation must be assisted by methane drainage, either from the mined seam, or from adjacent seams and strata, or from goafed areas. South African collieries have practised only limited methane drainage until now. Relatively shallow mining depths, and apparently low in-seam methane contents have been assumed to result in fewer problems with methane than are the normal for other countries. This is now being shown to not necessarily be the situation. Work carried out by the Coal Mining division of COMRO (Cook and Erwee, 1991) indicates South African production coal seams have very similar methane retention properties to those of coals in other countries, with seam gas contents of up to 12 m3/t. This awareness, as well as greater mining depths, and higher degrees of mechanisation, has resulted in higher priority being given to methane emission problems throughout the industry. Increased levels of safety, as well as possible commercial applications, are the main reasons for the interest now being shown in methane drainage. Not only is there possible applications in the present production coalfields, but South Africa has vast areas of coal reserves which are presently non-mineable, now being seen as possible alternative energy sources. Limited methane drainage is practised within the industry, but only on collieries that have identified specific methane problems that can be alleviated by drainage. Historically this has been restricted to surface drainage of longwall goafs, reducing emissions onto the faces. More recently, horizontal in-seam holes have been drilled, until now for bord and pillar sections, but the results are being evaluated for later application to shortwall faces. Adjacent seams pose problems at some sites and vertical and cross measure boreholes are now being considered.

Jan 1, 1993

By John M. Ackerman

INTRODUCTION In the spring of 1988 the Joint Venture of Freeport-McMoran Resource Partners, Limited Partnership, IMC Fertilizer Inc, and Homestake Mining Co. was awarded the sulphur lease for Main Pass Block 299, lease number OCS-G 9372. This was one of eleven leases awarded to the Joint Venturers. Following the initial discovery wells in December 1988, a program of delineation drilling confirmed proven sulphur reserves of 67 million long tons. Proven, recoverable oil and gas reserves are 39.4 million barrels and 7.2 billion cubic feet, respectively. Development of the sulphur mine was given approval as a fast-track project by the Joint Venturers in 1989. The oil and gas reserves were acquired from the original hydrocarbon lessee in 1990 and given fast- track status immediately. Fast-track for these projects meant design and engineering would not be complete before construction began JOINT VENTURE The Main Pass Joint Venture is one of thirteen joint ventures formed between Freeport and three other companies - IMC Fertilizer, Inc., Felmont Oil Corporation, a wholly owned subsidiary of Homestake Mining Co., and Texasgulf Minerals and Metals Co. Felmont has subsequently changed its name to Homestake Sulphur Co. and Texasgulf assigned their interests in the three leases they participated in to their parent company. Texasgulf did not participate in the Main Pass 299 joint venture. Joint venture negotiations, anticipating a lease sale in mid-1988, began in December of 1987. This Joint Venture was the first of its kind; created to acquire offshore leases, explore, develop and mine sulphur. The Minerals Management Service announced a lease sale date of February 24, 1988 on the first business day of 1988. This greatly accelerated the joint venture negotiations. Of the thirteen leases the Joint Ventures bid on, eleven were awarded. Freeport holds its interest in all the leases through its ownership interest in Freeport-McMoRan Resource Partners, Limited Partnership, and Resource Partners is the operator on all of the leases. The Main Pass joint venture percentage ownership is: 58.33 Freeport-McMoRan Resource Partners 25.00 IMC Fertilizer, Inc. 16.67 Homestake Sulphur Co. 100.00 The Main Pass Joint Venture paid $3,401,757 for the Main Pass lease and will pay a royalty of 12.5 percent of production value to the MMS . LOCATION The Main Pass mine complex is located in the Gulf of Mexico, in U. S. federal waters, about 27 kilometers (17 miles) east of Venice, Louisiana or 140 kilometers south east of New Orleans, Louisiana. It is situated in about 63 meters (210 feet) of water. HISTORY The Minerals Management Service (MMS) of the United States Department of the Interior administers the mineral properties of the United States located in federal waters. Periodically the MMS holds lease sales of blocks under its jurisdiction. Prior to the offshore discoveries of sulphur associated with salt domes leased for hydrocarbons, the MMS leased blocks with all minerals including hydrocarbons awarded to the successful bidder for the block. In 1963 MMS held the first lease sale of blocks specifically for sulphur. This sale was followed by a similar sale in

Jan 1, 1992

By D. M. Range

Exxon is reclaiming an 80-hm2 (200¬acre) Wyoming uranium tailings basin in accordance with US Nuclear Regula¬tory Commission (NRC) requirements. The reclamation plan is designed to control the tailings and their radioactive emissions for at least 1000 years. Rigorous modeling and analyses of potential erosion by wind and water were used in planning. The use of riprap was minimized and the need for long¬term reclamation maintenance was eliminated. The resulting design is simi¬lar to regions stable from erosion cre¬ated by nature. The concepts used in the design and implementation have wider reclamation application. Highland history Exxon operated the Highland uranium operations from 1972 until mid-1984. Open pit and underground operations mined the roll front, sandstone ore body. The 2.5 kt/d (3000 stpd) mill employed conventional crushing, grinding, sulfu¬ric acid leach, CCD, SX, precipitation, and drying circuits. The mill produced 10 Mt (11 million st) of tailings. An¬other operator began commercial scale in situ leach operations in 1988. The tailings basin was constructed by deposition of mill tailings in a natural ravine dammed with a 30-m (100-ft) high by 1050-m (3400-ft) long clay core earthen dam built entirely downstream of tailings. Figure 1 shows the layout of the tail¬ings basin in 1984. Tailings were de¬posited along the dam face on the east side of the basin as well as in the west end and along the south edge until the early 1980s. This left a deep water pond in the middle of the basin. The deep pond was largely filled with tailings during the last four years of mill opera¬tions by the construction of two tailings causeways and the operation of a float¬ing tailings line. The pond water volume was mini¬mized by recycling tailings water to the mill and by operating a 32-L/s (500¬gpm) evaporation enhancement spray system during the last few years of mill operations. Regulatory requirements Several conceptual tailings basin rec¬lamation plans were prepared during the mine life. In September 1984, Exxon began preparation of a detailed plan in response to an NRC request. Water, Waste and Land Inc. (WWL) of Fort Collins, CO was selected to help pre¬pare the plan that was submitted to the NRC in December 1984. The design had to meet the require¬ments found in NRC regulations (NRC, 1985). These were based on regulations prepared by the Environmental Protec¬tion Agency (EPA, 1983) at the man¬date of federal law (UMTRA, 1978). The NRC regulations contain strict primary standards and a somewhat more flexible set of secondary standards. The primary standards include requiring that: • radiation from tailings be reduced to background levels; • radon gas emitted by the tailings be reduced to 20 pCi/m2/s from the surface of the reclaimed tailings pile; • tailings not be dispersed into the environment; and • these conditions endure without routine maintenance for at least 200 years and for 1000 years to the extent reasonably attainable. The lengthy time requirements pre¬sented a large engineering challenge. Radon is a radioactive, chemically inert gas with a 3.8 day half-life. It is released from uranium tailings by the radioactive decay of radium, which, in turn, is a radioactive decay product of uranium. Radon emissions from ura¬nium tailings can be controlled with an earthen cover thick enough that the radon gas decays to its solid, short-lived radio¬active daughters before the radon dif¬fuses through the cover material into the air.

Jan 1, 1989

By J. W. Stevenson

At this 5th U.S. Mine Ventilation Symposium I would like to focus your attention on safety and the contribution of the ventilation engineer over the past 50 years. This conference affords us the opportunity to express, to listen, and to learn. As ventilation engineers it is indeed an exciting time--a time that not only stimulates our imagination but also pin points our aims in our quest to obtain zero fatalities by the year 2000, the goal expressed by William J. Tattersall, Assistant Secretary of Labor, Mine Safety and Health Administration. In the past, coal mine ventilation has often been unfortunately synonymous with explosions and resulting fires. Those not familiar with us do not recognize the painful evolution of the coal mining industry and particularly the evolution of mine ventilation. To put my presentation into perspective, I recently reviewed a U.S. Bureau of Mines Bulletin No. 586 - "Historical Summary of Coal-Mine Explosions in the United States 1810 - 1958 prepared by H. B. Humphrey Mining Health and Safety Engineer. This bulletin was published in 1960. Mr. Humphrey stated "In 1946, factors contributing to the explosions occurring from 1941 to 1945 were: (1) The rapid increase in the use of electrical equipment at face regions where gas and dust are most likely to be found; (2) the increased demand for coal with the desire to obtain maximum tonnage per machine at minimum cost, which in many mines has resulted in neglect of even rudimentary precautionary measures; (3) multiple-shift operation without provision of time for adequate maintenance of equipment, effective rock dusting, and testing for gas; (4) decrease in supervision owing to demands on supervisors for maximum tonnage and loss of competent supervisors to other employment; (5) lack of effective supervision, owing to numerous new conditions, some of them war-connected; (6) inability to obtain adequate equipment repair and replacement parts; (7) shortage of labor and inadequate training of coal-mine workers; and (8) failure of both miners and mining officials to show regard for safety in changing from hand-loading to mechanized methods". Most of the eight factors listed by Mr. Humphrey continue to affect our work lives as mining engineers. The increased demand for coal with the desire to obtain maximum tonnage per machine at minimum cost has never changed. The local and regionalized coal industry of the 40's is today competing against the world coal market. Our mines work or shut down based on cost. This has always been the case. During the five year time-frame Mr. Humphrey was documenting, 345 miners were killed in major explosions. A major explosion was one in which five or more miners were killed in a single accident. In addition, 105 more miners were killed in minor explosions for a total of 450. What a wanton waste of life. What fears, anxieties, miseries, and sufferings were created by these accidents. However, we must remember and keep in mind that the coal mining company officials, engineers, and foremen, the governmental agencies- federal, state, and local - were using the technical tools and knowledge available to operate the mines as safely as they could. Obviously mine ventilation engineering technology was woefully inadequate.

Jan 1, 1991

By W. Jacobi, K. Eisfeld

The primary objective of dosimetric modelling for the inhalation of radon daughters is the evaluation of the dose distribution and of the mean dose to sensitive cells or target tissues in the respiratory tract which are assumed to be responsible for the initiation of lung cancer. The results of such dosimetric models are influencing the practice of radiation protection in a twofold manner: Firstly, they enable us to identify appropriate operational quantities for air monitoring and for the surveillance of individual exposures to radon daughters. Secondly, they can be used to derive secondary and operational limits for these radionuclides from the basic dose limits. The dose to target tissues in the lung from inhaled radon daughters depends on various physical and biological parameters: The unattached fraction of daughter atoms, the AMAD of the carrier aerosol for attached atoms, the geometry of the respiratory airways, the breathing conditions, the parameters for the retention and translocation of daughter atoms in the different lung regions, and the location of the target cells or target tissues, respectively. Therefore, dosimetric modelling for radon daughters has to include a sensitivity analysis showing the influence of these parameters. To meet these objectives we have recently described in a comprehensive report an improved dosimetric model for the inhalation of 222Rn, 22ORn and their short lived daughters (Jacobi and Eisfeld, 1980). In the following this model is shortly described and the main results are summarized. DOSIMETRIC MODEL [Model Structure]. For the geometry of the bronchial airways the model A of Weibel (1963) was used. Each bronchial generation i (i =0.1 .... 16) was considered as a separate compartment i, for which the following transfer pathways for radon daughter atoms were taken into account (see fig. 1): (1) the uptake by deposition (deposition probability wi); (2) the translocation by ciliary clearance (rate constant [A]i); (3) the transfer to blood by diffusion through the bronchial epithelium (rate constant [A]b). To distinguish between attached (Index a) and free (index f) daughter atoms each bronchial generation was divided in two subcompartments (i.a and if) with a transfer rate constant [a]s (ia- if) characterizing the desorption or dissolution rate of attached atoms in the mucus fluid. Thus for daughter atoms primarily deposited in attached form the transfer to blood is a twostep process with the rate constants [a]s and [A]b which were assumed to be independent of the generation number i. [Deposition]. The deposition probabilities wi in each bronchial generation were calculated on the basis of the laminar diffusion model of Gormley et al. (1949); however the deposition in the upper airways was corrected for turbulent air flow, taking into account the results of our deposition experiments (Martin et al., 1972). Figure 2 shows the resulting deposition probabilities per unit surface area of the bronchial generations for nose breathing at a rate of 20 1/min. The values for attached daughter atoms refer to an AMAD of 0.2 - 0.3 µm ([O]g =3) for the carrier aerosol; the deposition values for free atoms were derived with a diffusion coefficient of 0.05 cm2/s, assuming a prefiltration of 50% in the naseopharyngeal region.

Jan 1, 1981

By Maribeth Amyot, Y. J. Wang, S. S. Peng

Introduction The impact of computers on individuals and businesses increases each day. And the mining industry is no exception. The growing number of short courses, symposia, and feature articles in journals on the subject of computers is indicative of the developments and interest in their application to mining. Given this interest and the growing importance of computers, a legitimate concern is the computing background of graduating mining engineers. Based on a sample survey, this paper presents the current status of computer education in Accreditation Board for Engineering Technology (ABET)-accredited mining engineering programs in the US. Specific topics addressed include hardware and software available to students, integration of computers into curricula, concerns of mining educators, and historical and anticipated trends in computing education. Methodology Nine of the 19 ABET accredited mining engineering schools (as published in the SME-AIME Guide to Minerals Schools) were surveyed. Interviews consisting of open-ended questions were conducted with a knowledgeable faculty member from each of these schools. This was done to obtain an overall view of computing in mining engineering programs. The intent was not to evaluate nor compare individual schools, so a complete census was deemed unnecessary. The minimal deviations between the responses to the subjective questions reinforces the credibility of the sample as being representative. Results Hardware Most of the mining engineering schools polled had access to hardware on three scales - mainframe computers available university wide, minicomputers available in the college or department, and microcomputers available at all three levels. Without exception, each school had access to mainframe and microcomputers. Minicomputers, however, were not available at every school. The mainframe computers have been in place the longest. The predominant mainframe currently on campuses is the IBM model. Mainframes were once the essence of all applications. But the improved availability and capabilities of smaller machines have afforded users a viable alternative. The increasing practice in education of assessing charges for time used on the mainframe - as opposed to no charge for time on the mini- and microcomputers - makes use of the smaller machines attractive. Conversely, much of the mining engineering software is only operational on mainframes. Sometimes this restriction exists because the requisite speed or storage inherent in the software can only be met by the mainframe. More often, however, it is because the software was developed when mainframes were the only machines available, and it has not yet been adapted to run on a smaller machine. At the schools polled, many mining engineering problems that are well suited to microcomputers are being solved on mainframes simply because microcomputer software is not available. Minicomputers are available at the department or college level in many mining programs. DEC is the most popular make. Often, the minicomputers were installed to alleviate the inconveniences of attempting to access and use an overcrowded mainframe, to avoid being charged for time used on the mainframe, and to meet the needs of a specific research project. The minicomputers are currently used much more for research than for teaching applications. Therefore, minis are seldom used by undergraduate students. Microcomputers have become extremely popular at mining schools within the last five years. Generally, some form of computing policy or strategy was established near the time the first microcomputers were purchased. This was formulated in part to ensure consistency, or at least compatibility, in the type of machines acquired. Microcomputers were subsequently selected based on the established computing policies; ma-

Jan 7, 1985

By G. Le Bel

Discussion by G. Le Bel The paper proposes three methods to determine optimum lifetime of a mining project 1. The conclusion is that the three methods arrive at the same optimum production rate (by coincidence). It is also stated that: "The stochastic and option pricing models, in addition to providing a more realistic optimum mine life than the traditional NPV (net present value) calculation, showed that the example project has the potential for substantially higher return. By explicitly considering a project's potential risks, the stochastic or option pricing techniques can more accurately describe its probable investment performance." This discussion is intended to demonstrate that: •It is no coincidence that the three methods arrive at the same optimum production rate. • The stochastic and option pricing models do not provide a more realistic optimum mine life than the traditional NPV calculation. •The potential for a substantially higher return is misrepresented. First, a review of investment decision theory in mining is needed. Net present value is the preferred performance measure because of the flexibility offered when comparing various alternatives. However, it presents the following disadvantages: • The discount rate selection is not straightforward. • The NPV obtained represents a deterministic characterization of the variables included in the cash flow calculations, i.e. a single-point estimate. Discount rate selection The opportunity cost of capital represents the rate of return that would be obtained if the capital was instead invested in other opportunities considered to exist. Such opportunities must be bypassed if the available capital is invested in the project studied 2. If these other opportunities carry risk similar to the project under analysis (for example, if they are other mining projects), there is no need to add incremental [ ] risk factors. On the other hand, if these opportunities are represented by the acquisition of government bonds yielding 7%, a risk premium factor must be included. The types of risks associated with a mining venture are shown in Table 1. Together they represent the "business risk" of being a mining company. The individual project risk is important to investors if it differs substantially from the business risk of the company and that of the other investments in mining ventures that we must pass up to invest in this particular project. A risk premium or discount would then be required. This can be illustrated by the following example. Consider that a company has two investment alternatives: one is the Cavender hypothetical project located in Nevada, and the other is the same project located in a civil war zone of central Europe. The second project requires a risk premium factor on the discount rate. Conversely, a project showing highly uncertain returns that are negatively correlated with the returns of the firm's other assets may decrease the company's corporate risk. Deterministic character of NPV calculation The cash flows used in NPV calculations are obtained from a set of variables. These variables are estimated using one parameter obtained from the engineering studies. Each parameter is thus a single value that is often termed a "realistic" or "best estimate" as opposed to "optimistic" or "pessimistic." However, considering that each variable can assume a range of values between the

Jan 1, 1994

By Bruce E. Holbein, Dennis K. Kidby, Ann L. Huber

World gold production figures and the processes used for gold production indicate a high dependence on both cyanide leaching and carbon adsorption metallurgies. Problems associated with the use of carbon in the treatment of refractory ores as well as economic and environmental considerations associated with the use of cyanide point to the advantages that can be realized through the use of more efficient gold adsorption media and with cyanide recovery. We have developed a process termed AurosaveTM-1 which provides a number of advantages through the use of a new synthetic robust gold adsorption medium, termed Vitrokele TM V-911. This process allows further recovery of gold from a variety of ores and allows for a simplified process for use not involving thermal regeneration or high pressure elution. We have also developed a cyanide recovery process termed Cyanosave ™ which uses Vitrokele TM V-911 and allows efficient recovery of cyanides from decants or tailings and re-use of recovered cyanide. This obviates the high chemical expenses for cyanide destruction where environmental issues require such water and tailings management.

Jan 1, 1998

By R. W. Lawrence, P. B. Marchant

Biohydrometallurgy is now forty years old. Since the discovery of the role of microorganisms in the oxidation of sulphide minerals that gives rise to acid mine drainage, many workers in industry, research organizations and academia in many countries have been active in attempts to develop practical commercial processes which exploit microbiological reactions in mineral processing and extractive metallurgy. Reactions which have potential and are being actively researched include:

Jan 1, 1998

By D. R. Baughman

Copper oxide deposits that may be considered for in situ leaching exist in unique geologic settings, different from uranium deposits. A large number of interrelated factors must be considered in wellfield design. Many of these factors are hard to quantify and are directly related to geologic features of the orebody. This paper discusses some of the important factors in wellfield design and suggests an outline for a design procedure.

Jan 1, 1988

By S. P. Chong, Peter V. Avotins

The iron and steel industry continues to operate at depressed production levels due to the low level of demand for steel and foundry products. Crude steel production in the Western world dropped by 13.7% from 459.3 Gt (506 billion st) in 1981 to 396.4 Gt (437 billion st). The reduction was particularly severe in North America where the industry suffered a loss of 37.3% from 123.6 to 77.5 Gt (136 to 85 billion st). This reduced level of production severely affected iron ore and agglomerates output. Substantial curtailment was made in both sintering and pelletizing plants to meet reduced demand. The pressure on these plant operators shifted from quantity to quality. With energy cost becoming an ever increasing part of production costs, conservation was a major area of emphasis. Iron Making Sinter has continued to be the favored burden for blast furnaces overseas. As hot metal production declined and excess sintering capacity developed, many of the overseas operators that have been using pellets found it advantageous on hot metal production cost to increase the ratio of sinter at the expense of pellets. This was the case despite the depressed price level of pellets in the world market. In North America where pellets have been the predominant burden material-mainly because it is necessary to pelletize the fine grain iron ores available domestically-there was also increased interest in sinter usage. Bethlehem Steel Corporation's 13.6-m (44.5-ft) furnace at Sparrows Point experimented with a burden with more than 70% of sinter during the second half of the year and indicated some favorable results as compared to its previous 50% super flux sinter and 50% acid pellet burden. The blast furnace operators continued to press for improved burden quality. In addition to the emphasis on the importance of burden chemistry and quality, uniformity, much emphasis was placed on improving reducibilitiy and high temperature metallurgical qualities. These burden properties were recognized to hold further promise in reducing fuels rates. Sintering With reduced consumption caused by the cutback in hot metal production, many sinter plants sat idle while others operated at greatly reduced rates. The deemphasis on production in many plants allowed them to experiment with various means to reduce operating costs. The most notable action was the introduction of low cost South American pellet feed fines into the sinter ore mix. These feed fines, which are finer than 150 µm (100 mesh) ore, were previously thought to be too fine for sintering. However, when the full production rate is not required the use of up to 40% in the ore mix was reported to be successful with the aid of burnt lime and adequate premixing and granulation of the sinter mix before sintering. The emphasis on quality and tighter cost control also has resulted in a further breakthrough in sintering technology. It was recognized that good feed preparation-including selection of compatible ores, good blending, good pseudo-particle formation, additive size control increased bed depth, and closed control of the sintering bed heat pattern-could allow the production of high quality sinters with much lower heat input and FeO level. Bed depth of more than 600 mm (23.6 in.) was practiced in a number of operations. Total heat input of better than 1.3 GJ/t (290,300 kcal per st) has been achieved. Kawasaki Steel's Chiba Works has also achieved a 5.3% SiO2 in the sinter with good quality. The low heat input approach allowed production

Jan 5, 1983