Search Documents

By Ronald E. Yarbrough

As a result of concern for the citizens of the State of Illinois who owned structures above underground mine workings, the Illinois State Legislature passed House Bill 158 in 1978. This bill amends the Illinois lnsurance Code and creates the Mine Subsidence Reinsurance Fund which is an insurance pool that is to receive a state appropriation of $500,000 as "start-up" money. One hundred thousand dollars has been paid to the fund as of October, 1982. The Fund is to return this appropriation to the State and is to remain self-supporting from premiums. The Fund utilized a pre-existing institution, which also was an insurance pool, the "Fair Plan Facility" and its governing Board, consisting primarily of insurance executives, to administer the program. The Mine Subsidence lnsurance Act went into effect October 1, 1979, and the bill provides that property owners in the State of Illinois may purchase up to $50,000 of mine subsidence insurance which is attached to their fire insurance policy. The deductible is normally 2%, but cannot be less than $250 or more than $500. The annual rate structure for residential structures in 1981 for $50,000 coverage is $10 (frame), and $12 (masonry). The rate structure for commercial buildings is based on the value of the building and the rates for $50,000 maximum coverage is adjusted upward. The insurance was mandated by the State Department of lnsurance and rolled onto the insurance policies of the homeowners in 34 counties which had been recognized as having sufficient exposure to subsidence damage to be covered by the Act. One percent or more of the land surface is undermined in each of the 34 counties. In the other counties undermined in the State of Illinois, insurance is available to the homeowner upon request to the private insurance carrier.

Jan 1, 1982

By C. G. Cunningham

The Marysvale volcanic field of west-central Utah contains large areas of argillically altered rocks (fig. 1) that, in turn, enclose smaller areas of fine-grained, medium-grade, replacement alunite deposits and coarsely crystalline, high-grade vein-type alunite deposits. The largest replacement alunite deposits are [ ] located peripheral to a 23-m.y.-old monzonite stock called the Central Intrusive (fig. 1). The deposits formed in near-surface, highly oxidizing environments at the tops of hydrothermal plumes that were spaced irregularly around the stock. The deposits are horizontally zoned from alunitic cores through kaolinitic to propylitic envelopes. Vertically, characteristic alteration minerals progress from a pyrite-propylitic alteration assemblage at the base, upward through alunitic, jarositic, and hematitic assemblages to a flooded silica cap as shown on figure 2. The silica caps are cut by hydrothermal explosion breccias. d34Sso4 values of + 11.5 to + 15.4 permil indicate that sulfur in the hydrothermal plume was derived from underlying Mesozoic evaporites. The sharp upward transition from pyrite- propylite to alunite probably marks the paleowater table, and the top of the flooded silica cap represents the paleoground surface. Basin-Range extensional tectonism began shortly after alteration, and buried the replacement alunite deposits in basins beneath sediments eroded from uplands. The deposits were only recently exhumed.

Jan 1, 2013

By James C. Irvine

Pea Ridge Iron Ore Co., previously Meramec Mining Co., a joint venture by Bethlehem Steel Corp. and St. Joe Minerals Corp., mines and pelletizes iron ore at the Pea Ridge mine. The Pea Ridge property, now wholly owned by St. Joe, is located near Sullivan, MO, about 112 km (70 miles) southwest of St. Louis. The ore body was delineated in the mid-1950s by St. Joe during a lead exploration program. The first test holes drilled on the Pea Ridge magnetic anomaly revealed the presence of a large magnetite deposit; further drill¬ing in 1956 and 1957 confirmed that the ore body was minable. Meramec Mining Co. was incorporated in 1957 and shaft sinking began late in the year. Pro¬duction commenced in April 1964. The ore body is overlain by about 396 m (1300 ft) of flat-bedded sediments. It is tabular, about 792 m (2600 ft) long, and up to 182 m (600 ft) thick. It dips about 1.39 rad (80°) and is of unknown depth. The ore is mainly high grade magnetite with small zones of specular hematite. The wall rock is a Precambrian rhyolite porphyry. The mine was initially started with five major levels on 45-m (150-ft) intervals. Crosscuts were driven across the ore body on 58-m (190-ft) centers. Banks of stopes were mined between the crosscuts by a modi¬fied shrinkage stoping method (Fig. 1). This was done by undercutting a 12 m (40 ft) wide by 45-m (150-ft) long block and blasting horizontal "lifts" drilled on 1.5-m (5-ft) intervals. A 20-m (65-ft) sill was left between levels which contained the slushing drift, fin¬gers, crown pillar, and adequate thickness for support. By 1971 a "lattice" of pillars had been left and mining had progressed to the point that an orderly pillar re¬covery program was necessary (Fig. 2). INITIAL PILLAR RECOVERY PROGRAM The program was started in the upper western por¬tion of the ore body, furthest from the shafts. Due to the fact that the ore body narrows in the western extremity, the stope orientation was changed to mini¬mize required development. This left pillars 18 to 24 m (60 to 80 ft) wide and up to 79 m (260 ft) in length. The area selected for the start of the program had been developed between the uppermost level at 419 m (1375 ft) below surface and the 510-m (1675-ft) level. Due to the 91-m (300-ft) difference in depth, sublevels were driven on 15-m (50-ft) intervals and the ore was taken by rather classical sublevel stoping methods (Fig. 3). This left a structure with accesses compatible with drilling with 114-mm (41/2-in.) bore drifters mounted on columns. Most holes were drilled 63.5 mm (21h in.) diam and reamed to 100 or 127 mm (4 or 5 in.). Practical depth capability was about 21 m (70 ft) for holes above horizontal and 13 to 15 m (45 to 50 ft) for holes below horizontal. The interdependence of these long pillars necessitated that several of them be blasted simultaneously, making large blasts the only practical approach. Due to the required length of such loading cam¬paigns, it was necessary to select an explosive which could stand in the hole in an underground mine for a 4 to 6 week period. After some consideration a pump¬ able water gel was selected for both uphole and down¬hole loading. This afforded a high velocity, high density explosive which could be handled in large quantities. Loading the downholes was a fairly straightforward process. The holes were lined with an 8 mil polybutylene plastic sleeve and water gel was pumped into them with a double diaphragm pump mounted on the bottom of a stainless steel tub with a 81-kg (180-1b) capacity. Potential leakage into cracked areas of the pillar was

Jan 1, 1982

By R. Ramesh

Understanding the nature of coal surface heterogeneity is a prerequisite to accurate characterization and efficient control of coal surfaces. New techniques based on the centrifugal immersion of particles from the liquid/ vapor interface and film flotation have led to independent estimation of surface energy distributions in individual coal particles. Changes in the distribution of surface sites due to oxidation and polyacrylamide adsorption on coal are studied here using the above techniques. New information on -possible conformations of adsorbed polymers is also obtained.

Jan 1, 1989

By Martha E. Smith

INTRODUCTION Radiation is one of the many agents occurring in our environment that is capable of causing cancers. We are all unavoidably exposed to natural background radiation. If we wish to exploit the beneficial uses of radiation in medicine, industry, and for the production of electricity, some further exposures to radiation are almost inevitable. One needs to ensure therefore, that the standards of radiation protection are safely derived and one would want to understand the mechanism by which radiation might cause cancer and genetic defects. In order to study the effects of radiation one can: (1) analyze human data, (2) perform animal experiments, and (3) do molecular level experiments. Indeed all three kinds of information are needed. This paper will concentrate on the steps required to obtain some of the necessary human data regarding health effects, where the concern is about the impact and consequences of long-term low-level exposures to an agent. Such investigations require some knowledge of work histories, dose histories, health "outcomes", and the personal identification of the individual involved. Three inter-related computer systems have been developed at Statistics Canada which have been designed to permit optimal use of a number of different records for our entire country for such health related research. The development of the Canadian Mortality Data Base, the initiation of the National Cancer Incidence Reporting System, and the development of new computer linkage techniques have helped reduce the cost and increase the scale and efficiency of automated follow-up to produce statistics of sickness or death associated with radiation and other carcinogenic agents in mines. These computer systems have already been implemented, and references will be made to studies currently being conducted using these files and facilities (e.g. a study of all Ontario miners, plus various Canadian uranium, fluorospar, salt and nickel miners). We will also look at the kinds of data that need to be collected now, to improve such studies in the future. DELAYED RISKS - THE STUDY SIZE AND COST Delayed effects on human health, as for example industrially caused cancer, can in general only be detected and measured by following-up the individuals to see what eventually becomes of them. What is not generally recognized is that the relatively low levels of individual risk, about which the public is often concerned, usually requires for their detection that very large numbers of "exposed" and "control" individuals (e.g. 10,000 to 100,000 or more) be followed over a period of two or three decades to determine when they die, what they die of, and whether they contracted cancer or some other disease of special concern. Thus, it is frequently exceedingly difficult to make such investigations cost-effective so that they will be undertaken at all, and as a result very real risks to health can remain undetected or unquantified. THE MANUAL PROCEDURES Follow-up of individuals by epidemiologists has until recently been a largely manual and clerical operation. It has used a diversity of source record files; local, regional, and national. Often the tracing of people has involved letters sent through the mails and visits to institutions, physicians, municipal offices, and former neighbours. Only thus could one find out whether the individuals were dead or alive. Such studies were necessarily small, or else very expensive. Death registrations have, by tradition, provided a valuable tool for the identification of harmful influences in the environment. However, with the increasing mobility in the population, death may often occur far away from the place of exposure to such an influence. Thus, no longer will simple manual searches in a single registry office suffice to inform the investigator concerning the deaths that may have occurred in a study population, especially when that population is large. In the past, manual follow-up to locate the relevant death registration normally required some prior knowledge of the province and year of death in question, so that the alphabetic indexes could he used to direct researchers to the appropriate bound volumes of registration forms. To search manually in this fashion for any large number of death registrations, without knowing in which year or province the deaths had taken place, or even whether they had yet occurred, would be impractical, since each year in Canada there are about 170,000 deaths. DEATH AND CANCER AS SPECIAL ENDPOINTS Much of recent effort has been focused on the organization of the "endpoint" files required to do long-term follow-up studies on a national scale, because that is a function which other institutions are unable to perform due to the confidentiality laws governing the use of such information. Outside organizations generally come to us with detailed "starting" point records which relate to some specific group requiring study. We carry out these epidemiological searches on a cost-recovery basis. The analytical interpretation of results is normally

Jan 1, 1981

By H. Polat, Q. Hu, M. Polat, S. Chander

The electrostatic charge on spray droplets of ionic surfactant solutions and coal particles was measured and the results were correlated with the dust collection efficiency. When various surfactant were added, the magnitude of the droplet charge increased significantly and it was observed to be a function of surfactant type and concentration. The concentration of maximum droplet charge coincided with surfactant concentration where maximum collection efficiency was observed for these surfactants. Particles of coal also carried substantial amount of charge magnitude of which seemed to be a function of coal rank. Based on the results presented in this paper, it was concluded that ionic surfactant primarily act as a strong electrostatic charge inducer for droplets. Due to interactions between these highly charged droplets and naturally charged particles, the efficiency of droplet-particle collisions play a primary role when compared to the wetting and engulfment phenomenon which could only follow a successful collision. INTRODUCTION Water spray are widely used to suppress airborne dust in mine atmospheres (Walton and Woolcock, 1960; Kobrick, 1970; Hamilton, 1974; Jayaraman et al., 1986). Several investigators have considered the use of surfactants to enhance the effectiveness of water sprays especially for difficult to wet particles such as those of coal (Glanville and Wightman, 1979). The capture of dust particles by water droplets involves droplet-particle collisions, adhesion of particles to droplets, and engulfment of particles into droplets. Surfactants affect these sub processes through their influence on droplet charge, surface tension, and wetting. The last two mechanism have been thoroughly studied in recent years (Walker et al., 1952; Cohen and Rosen, 1981; Glenville and Haley, 1982; Chander et al., 1988; 1991). However, little attention has been paid to the role of electrical charge on particles and droplets on the collision and adhesion of spray droplets and dust particles. Airborne particles of dust have long been known to carry a significant amount of electrostatic charge (Hopper and Laby, 1941; Kunkel, 1948; Kunkel, 1950; Dodd, 1952; Liu et al., 1987; Kutsuwada and Nakamura, 1989). It is reasonable to assume that presence of charge on particles will effect their agglomeration and particle-droplet interactions. Polat et al., (1991) showed that virtually all freshly generated dust particles were agglomerated in air. They suggested that electrostatic charge and humidity were important factors responsible for agglomeration. Previous theoretical studies on the interactions between charged particles and collectors by Nielsen and Hill (1976) show that, the collision efficiency is a strong function of the particle charge. In addition to charge on particles, spray droplets might also carry substantial amount of charge (Chapman, 1937;1938; Blanchard, 1958; Iribarne and Mason, 1967; Jonas and Mason, 1968; Byrne, 1977; Bailey, 1988). In theoretical studies of interactions between a spherical collector and airborne particle, it was found that the collision efficiency was significantly altered depending on whether the collector and the particles were charged. If neither the collector nor the particles carried a charge, the collision occurred by inertial and gravitational forces. The collisions took place on the front part of the collector (the front capture). If either of the collector or the particles were charged, the collision was enhanced due to the induced image forces. If both the collector and the particles were charged, the collision efficiency was significantly affected by the sign of the charge as well as its magnitude. For oppositely charged collector-particle pairs a collision could take place on the rear of the collector even if the particle flied past the collector upon approach (the rear capture) (Nielsen and Hill, 1976; Wang et al., 1986; Chang et al., 1987). On the other hand, the columbic force became negligible as the particle size increased and the inertial force became dominant. The electrostatic attraction was predominant for particles of less than about 2.5 µm in diameter. For particles larger than about 8 µm the inertia of particles was sufficient to overcome the columbic force and inertial impaction became the dominant collision mechanism (Grover and Beard, 1975; Chang, 1987). Previous studies of dust suppression using charged spray droplets generated by applying high voltage to the spray nozzle showed significant improvements in collection efficiencies (USBM open file report, 1983; McCoy et al., 1985). However, it was considered that highly charged spray droplets obtained by direct charging might have

Jan 1, 1993

By A. Dale Wunderlich

With the price of precious metals at an 18-year low, every ounce of metal produced is important. The theft of metals from mining and refining sites can mean the diffrence between profit and loss for many mining companies. Low metal prices do not reduce the potential for the theft of precious metals. History has shown that the price of gold has little to do with the desire for employees to steal precious or base metals. There is actually evidence that the theft of precious metals increases when the price of this commodity goes down. Several of the major precious metal thefts in the past year took place at silver mines when the price of silver was less than 16 cents/g ($5/oz). How does the lowest gold price in 18 years affect the need for security at precious metals properties? There is no short answer to this question. One reason is because the exposure to theft of precious metals is unique to each property. This makes it important that each property be evaluated individually. More than 95% of all precious metals thefts can be attributed to those working at the mine site. So preventing employee theft is the primary concern. One consideration is the location of the property. Gold selling at any price is still an attractive commodity in countries where the employees are making between US$400 and US$600 a month. It is not uncommon for employees at mines in countries where low wages are the norm to consider the value of a gram or two of gold to be a significant amount of money. A gram or two of gold a day may not seem like much. But if 15 employees steal two grams a day, that equates to a significant amount of money during a year. The type of property where the precious metals product is being recovered is also important. For example, a property with a gravity circuit is more likely to suffer from the theft of gold product than a property where all gold is finely disseminated and the only gold seen in the ore body is through a microscope. Gravity circuits increase an operation's exposure to theft because the grinding circuit that is associated with a gravity circuit often becomes a giant concentrator. Areas such as the bottom of grinding-mill pump boxes, cyclone-feed-pump clean out traps and the sumps often become locations where precious metals concentrate (Figs. 1 and 2). Muck concentrations in these locations can be as high as 25% to 40% of gold or silver. Not long ago, muck was removed from a barren-solution sump at a Merrill Crowe circuit that had concentrated to more than 40% gold. At a milling site in the Pacific Rim, residents of the community adjacent to the mine learned about the value of the concentrates in the sump under the ball mill and committed an armed rob¬bery. While several of their co-conspirators held the em¬ployees at bay with machetes, the others emptied the contents of the sump into buckets and removed it from the site. Armed robbery is not as common as employee theft. However, while this article was being written, an armed robbery occurred at a gold property in Central America. Armed perpetrators took as hostages the night shift employees at a process plant and used cutting torches that were on site to cut into the high-security and gold-storage areas. The perpetrators then stole a company vehicle to remove the stolen gold buttons and sludge from the site. Unfortunately, this type of activity goes on regularly. But managements of most mining companies are reluctant to discuss theft scenarios. So information pertaining to the theft of precious metals seldom becomes a newsworthy item. An audit conducted at a mine site with a gravity circuit recommended that the gravity recovery area be shut down until adequate protection could be provided. Although it was not connected with the audit, it was necessary to shut down the gravity area for a pro¬longed period because of problems with the gravity table. In the two months that followed, gold production at the site increased by about 31 kg/month (1,000 oz/month). It is difficult to attribute all of this increase to the theft of concentrates. But there was a good chance that at least part of the increase was due to the fact that concentrates were being stolen from the gravity area.

Jan 1, 1998

By Gregory M. Rumbaugh, Christopher Mark

"The proliferation of unconventional gas well development in the Northern Appalachian coalfields has raised a number of mine safety concerns. Unconventional wells, which extract gas from deep shale formations, are characterized by gas volumes and pressures that are significantly higher than those observed at many conventional wells. The gas is composed largely of methane as well as other hydrocarbons. Hundreds of planned and actively producing wells penetrate protective coal pillars or barriers within active mine boundaries, including chain pillars located between longwall panels. Gas released from a well damaged by mining-induced ground movements could pose a risk to miners by flowing into the mine atmosphere. The mining-induced ground movements that may cause well damage include conventional subsidence, non-conventional subsidence (e.g., bedding plane slip), pillar failure, and floor instability. This paper describes the known risk factors for each of the four failure mechanisms. It includes a framework that can guide the risk assessment process when mining takes place near gas or oil wells.INTRODUCTIONSouthwestern Pennsylvania has served for centuries as a producer of coal, oil, and natural gas. Coal mines were first developed in the Pittsburgh Coal Seam in the 1760s, with the first recorded mine in 1761 being the Fort Pitt Mine (Edmunds, 2002). Natural gas was introduced to the region when the Haymaker Well in Murrysville, Pennsylvania experienced a blowout on November 3, 1878. Although it was originally drilled prospecting for oil, it produced an estimated 30 million cubic feet per day of natural gas. Without well controls or pipeline infrastructure in place, it burst into flames and lit the night sky for over a year. Soon after, the Penn Fuel Company continued development of the Murrysville gas field and is credited with making Pittsburgh, Pennsylvania the first major city in the U.S. to have natural gas supplied for home and industrial uses. “Natural gas is king in Pittsburgh,” proclaimed an October 18, 1885, article in the New York Times headlined “Value of Natural Gas, Its Use Clarifies the Atmosphere at Pittsburgh” (AOGHS, 2018). By the early 1900s, coal, oil, and natural gas production had reached the southern extents of Pennsylvania in Greene County. The county had first produced oil in 1886, and shortly after began producing natural gas in 1890. By 1906, over 1,300 wells had been drilled (Stone and Clapp, 1906)."

Jan 1, 2019

Introduction The objective of the design and operation of a mine is to make as much money as possible within certain reasonable and responsible constraints. The imposition of constraints on the objective of maximizing profits can result in an optimum mine design. This paper deals with the maximization of profits. Optimization will be discussed in a future paper. In the mining industry, it is generally accepted that the maximum economic recovery is defined by identifying the reserves and the sequence of mining that results in maximum net present value (NPV) or discounted cash flow-rate of return (DCF-ROR), as indicated in Fig. 1 (see Lemieux, 2000). Current parametric analyses techniques, such as varying the mining costs; profit reservation; sales price or metal content, to define pit limits and mining sequence technically referred to single, double or triple parameterization, do not assure that the curve in Fig. 1 will be maximized. In defining the sequence, the first material to be mined should be the first grouping of recoverable mineral that has the highest after-tax unit value and that forms a feasible mining unit. The assumed mining of the first pit should be followed by the assumed mining of the second most profitable and practical pit or pit expansion. If this process of grouping and sequencing is followed until the profitability approaches zero, the general sequence required to extract the maximum economically recoverable reserve is identified. The curve in Fig. I is constructed by calculating the NPV for a series of sequences, each assuming operations are terminated on successively lower profit pits. If the operation ceases on a pit with too high of a profit, opportunity is lost, and the NPV is lower than the maximum. The NPV curve peaks and then starts to decline before the zero-profit pit is assumed mined. This occurs because the money invested in advanced stripping would have produced a greater return if it was invested at the dis¬count rate. The maximum economically recoverable reserve is defined by the pit limit corresponding to the maximum NPV or DCF-ROR. Pit and phase definition The real challenge of reserve definition is identifying the phasing and after-tax profit per ton, so that the curve in Fig. 1 can be plotted. The after-tax profit cannot be properly addressed until after the pits are designed, the production is scheduled and the cash flow is estimated. Throughout the years, many investigators have ad¬dressed this problem. A major thrust of the famous paper in which Lerchs and Grossman (1965) presented their algorithm was to identify a sequence that would produce a result similar to that identified in Fig. 1. Whittle's (1988) four-dimensional analysis is designed to address this issue. The author addressed this same issue in a paper presented to the 1968 Canadian Institute of Mining national convention (Lemieux, 1968). Without a relatively simple methodology to con¬struct the curve in Fig. 1, the number of iterations in a trial-and-error method becomes prohibitively burden-some. The pit designer seeks a simple pit-planning parameter that will serve as a proxy for the after-tax profit per ton used in defining the curve in Fig. 1. The designer's goal is to apply this pit-planning parameter using standard pit-wall location techniques to design a series of pits that will provide a guide to the sequencing. Common techniques used to position pit walls are strip-ratio limits, highwall incremental analysis, floating-cone methods or "maximizer" applications1. Costs, revenues, noncash charges, taxes and profits are usually structured on a unit basis for use in the pit-wall location analysis. Application of the proxy parameter using the pit-design tools should, ideally, result in the definition of pits and sequences that will maximize the curve in Fig. 1. 1 The pit-design tool frequently referred to in the literature as an "optimizer" defines a pit boundary that maximizes the value contained within based on the input parameters and the safe pit-wall angle. The optimization of the pit design involves selection of rate of production, cutoff grade, product quality and other considerations. These considerations constrain the maximization of value. Therefore, pit-design tools that maximize value should be called "maximizers."

Jan 1, 2000

By Robert W. Miller

There are many problems faced by ventilation engineers in deep underground mining operations, not the least of which is controlling miner exposure to radon gas and its daughter products. Radon gas is commonly found in uranium mining operations, but may also be present in other deep metal mines. For example, tin mines in England, iron ore mines in Sweden, gold mines in South Africa, and molybdenum mines in the U. S. have potential radon exposures. This is because uranium and accompanying radium ore are ubiquitous to the earth's crust albeit at low levels. The fact that the activity represented by one WL can be caused by a relatively low concentration of radon gas increases the difficulty of control. Since the source of the radon gas is usually widespread throughout a mine, local exhaust ventilation is not a viable control schema. The technique used to control exposure is then dilution ventilation and, in fact, huge amounts of air must be moved in order to reduce potential exposures to an acceptable level. An interesting comparison can be made of ventilation rates in different types of mines. It is estimated in modern coal mines, which are generally acknowledged to have high rates of ventilation, that about eleven tons of air are moved for each ton of ore mined. A typical operating uranium mine may have ventilation flows of 14-15 tons per ton of ore mined. This provides an idea of the scope and importance of ventilation in modern mining operations where radon is a hazard. Further pressure is put on ventilation engineers by the steady downward trend in exposure limits set by national and international standard setting agencies. Much of this tendency toward lowered standards is based upon longitudinal mortality studies of miner populations. Another important factor is the limited number of experienced miners available in the labor pool. For optimum production, it is important to have as many experienced miners underground in each shift as possible. However, the average daily exposure in a U. S. mine must be less than .3 WL to permit the miner to work underground for a full year. The ventilation system then must provide enough uncontaminated air to maintain the WL below the .3 TTL level to maximize production efficiency and minimize personnel turnover and the problems associated with it. Ultimately, the goal of the ventilation engineer and health physicist is to protect the working miner from harmful exposures based upon currently acceptable standards. U. S. Federal regulations require that in uranium mines all active work sites must be monitored every two weeks if they measure above .1 WL. Areas that have .3 WL ratios or higher must be monitored on a weekly basis until five consecutive weekly samples show the level has dropped below .3 WL. Also, exposure records must be kept for all individuals exposed to levels exceeding .3 WL. These requirements provide a strong economic incentive to have a ventilation system that minimizes exposure of any personnel. A good ventilation system requires careful planning, operation and backup in order to fulfill its mission of providing adequate clean air. Its proper operation also requires coordination with production personnel so it can be adapted as new areas in the mine open up and old areas are sealed off. The ultimate indicator of ventilation efficiency to control radon daughter exposure is, of course, monitoring working levels. Historically, this has been done using the Kusnetz, Tsivoglou, and Rolle's methods, among others. These methods all require cumbersome equipment and tedious calculations to obtain the measurements that results in WL. More important, however, they require a significant time lag between sampling and counting, typically 40-90 minutes. This time lag is, in fact, what can cause significant economic losses due to unnecessary downtime as well as high WL exposures. In a typical mining situation, a sampling technician using the Kusnetz method takes a sample, moves to the next location and takes another sample and so on. Forty to ninety minutes after the first sample, the technician will stop, run the activity count on the filter and calculate the WL. The technician may be one-half mile away or several levels removed from where the first sample was taken when it is counted. If the WL ratio is high the technician must then backtrack to the sample position. There are then two options. If the sample area is a working stage, it can be shut down or a second sample can be taken. If the first alternative is chosen; i.e., shutdown and correction of the ventilation, then another sample must be taken, followed by a forty minute wait for results. If the ventilation adjustment didn't correct the problem, then the whole process must be repeated with a minimum of forty-five minutes per sample cycle when using the Kusnetz method. It has been estimated from operating uranium mines that the cost per hour for downtime on a production slope is about $1,50O/hour. The time lag between sampling and resultant data can be very costly. If the second alternative is chosen to verify the first reading, the miners may be unnecessarily exposed to high levels while waiting for the result. Clearly, such a sampling system can be markedly improved by eliminating the excessive time lag between sampling and analysis.

Jan 1, 1981

By Jozef S. Stachulak

Inco Limited operates 11 underground mines in the Sudbury District. The mines are located on the rim of the Sudbury Basin, an oval with the axis in the range of 27 and 60 km. The ore dips to at least 3000 m below surface. The ores are mined primarily for nickel and copper. Total ore production from underground is in excess of 55,000 tons per day. Over 40 surface fans have been installed since the late 1960's. All of the fans are adjustable pitch, axial flow units. A major factor influencing ventilation design in the last 30 years has been the introduction of diesel equipment underground. Volumes per fan have ranged from 60 to 330 (cubic metres per second), with motors from 100 to 2500 hp. Fans of the axial flow type have been in common use for main fan installations at Canadian mines for many years. The standard arrangement has been to mount these fans horizontally, i.e. with the fan shaft and the long axis of the housing horizontal. This is a natural arrangement for an underground fan, but for a surface installation, a vertically mounted fan has definite advantages. The surface area taken up by a typical vertical fan installation is generally about one quarter of that with a horizontal fan of the same capacity. (1) This is not a problem with isolated fans and flat surface outcrop sites, but where the installation is to be near existing buildings, or where there are poor surface soil conditions, space and cost considerations greatly favour vertical fans. MAIN FANS INSTALLED There are 43 main surface fans in operation at 11 mines. Twenty-seven of these fans are supply units, and 75% of them are vertical installation. The remaining 16 units are main surface exhaust fans, with predominantly horizontal installation. Within the last five years, some 20 main booster fans have been installed underground at several mines. Axial flow fans, with adjustable pitch blades, are used for both surface and underground installations. Exhaust fans are equipped with stainless steel or cast aluminum blades. Main underground fans are arranged horizontally and the majority of them have a floating shaft between the fan shaft and the motor. (2) The size of the fans in service varies from 1.8 m to 5 m in diameter, with the majority ranging from 1.8 to 2.5 m. The pressure produced by these fans varies from 0.25 kPa to 2.0 kPa. At Inco Limited, two main fans in parallel are preferred, rather than a single fan, so that if one fan fails, the remaining fan can still supply up to 70% of normal air quantities, while the damaged fan is repaired. This requires closure doors on each of the fans so the fan can be isolated in case of failure. It is more expensive than a single fan, but results in less production interruptions. The fan installations are well away from sharp inlet and outlet bends. FAN DESIGN INTEGRITY Both the mine operator and the fan manufacturer must understand that the main fan is critical to the mine operation, and that everything technically possible must be done in design and manufacture to ensure the highest degree of reliability. Some of the design parameters and criteria, based on Inco experience, are outlined and discussed below. RESONANT FREQUENCIES AND HOUSING MODEL ANALYSIS Any fan assembly will have many different resonant frequencies. It is a challenge to the designer to arrive at a design in which forcing frequencies do not coincide with any of these resonant frequencies to produce unacceptable vibration levels in operation. Finite element analysis is a useful tool that can be used to identify the most critical of these, so that housing and blade stiffness can be adjusted to change any resonances that might be close to forcing frequencies. Shaft critical speeds should be at least 25% above the fan operating speed, and there should be sufficient separation between other resonant and forcing frequencies to avoid excitation that might result in high vibration levels. QUALITY ASSURANCE Radiographic Blade Examination Mine fan blades are normally cast in small lots. To ensure that the castings are sound, a full radiographic examination is recommended in the highly stressed lower 1/3 of the blade.

Jan 1, 1995

By B. P. Boisen

INTRODUCTION The rapidity of onset, rate of increase, and magni¬tude of loads in an underground support system can be measured using load cells or pressure cells, whichever is appropriate to the type of support. These instruments should be installed at the various instrumented station locations immediately after excavation. If the loading of a member is of interest, the load should be measured, whereas if the deflection or strain of a member is of interest, the strain should be mea¬sured. It makes as little sense to use a load cell to allow computation of strain as it does to measure the strain and then back calculate the load. Tunnel steel set de¬signers today invariably rely on the early work of Karl Terzaghi, the basis for which is load, so load measure¬ment should be the main concern. The current trend of using strain gages on steel sup¬port systems stems from the inability by some to eval¬uate unusual loading conditions caused by uneven block¬ing. In fact, uneven blocking will obscure almost any attempt (whether with load cells or strain gages) to properly evaluate support performance. The load curve in Fig. I shows the development of a characteristic early peak load sometimes called the "rear abutment load" seen in many underground open¬ings. It is thought that the peak reflects the coupling of the rock and the support system, and that the magnitude will increase until some yielding, or minor failure, of the support system occurs. At that time, the slight deforma¬tion of the support system promotes the formation of minute shears in the opening walls, and these shears tend to distribute stress between the support system and the adjacent rock in proportion to the relative rigidity of the support elements and the rock. In normal rock, as a result of this stress redistribu¬tion, subsequent load magnitudes generally do not reach the magnitude of the early peak load. In physically unstable (squeezing) or chemically un¬stable (swelling) rock, however, the loads experienced after passage of the early peak load may in fact show a slow, continuous increase. One of the very important purposes of load instrumentation is to provide the means for recognizing such long-term adverse trends, thus enabling the proper remedial steps to be taken. Another purpose of load instrumentation is to pro¬vide a comparison between the magnitudes of the early peak load and the subsequent stable load. The ratio of these two loads is analogous to a safety factor, and may be used to evaluate the efficiency and economy of the support system design. Aside from considerations of economy, it may be well to design support systems which do not have excessively high ratios of early peak load to subsequent stable load. Should these ratios be exces¬sively high, the support system may be so rigid that the yield or failure associated with stress redistribution may occur with explosive violence. Load cells for use in mines, tunnels, and on con¬struction projects come in many forms. Almost all, however, employ the same procedures for installation, readout, etc. Therefore the following comments are almost universal in application. LOAD CELL INSTALLATION Load cells should be installed with bases parallel to the surfaces against which they bear. Care must be taken to orient the cells so that their signal cables are protected from accidental damage as a result of con¬struction, maintenance, or cleanup activities. Most electronic load cells are compensated for tem¬perature variations likely to be encountered during nor¬mal operations. However, if a large difference is an¬ticipated between the calibration temperature [21°C (70°F)] and the average operating temperature, the cells should be conditioned to the operating temperature for at least 8 hr prior to installation. This is to insure that the initial reading, made under no-load conditions prior to installation, provides a stable value to which subse¬quent measurements can be referred. Hydraulic load cells tend to be temperature sensitive and should be used with that in mind. Also, hydraulic load cells tend to be soft compared to electronic types and will sometimes allow movement to take place in a system intended to be semirigid. Furthermore, hydrau¬lic load cells tend to be difficult to read remotely. Care must be taken to use bearing plates on both sides of load cells which are sufficiently rigid and of high enough bearing capacity to prevent bending and crush¬ing under load. This is very important with tieback load cells (basically a ring of steel) which can easily dig into bearing plates. MAINTENANCE AND TROUBLESHOOTING Except for a direct hit by a miner's axe or flyrock from a blast, most hydraulic load cells are nearly in¬destructible and require little, if any, maintenance. Hy¬draulic oil on the bearing plates is a good indication of a leak and the need for corrective action. Field maintenance of electronic load cells involves protecting the instrument and signal cable from mechani¬cal damage and from unnecessary exposure to dirt and moisture, and recognizing and correcting damage and the effects of normal wear and tear.

Jan 1, 1982

By Aladar B. Dory

INTRODUCTION Practical experience in mines with known presence of radon daughters in the mine atmosphere in Canada and elsewhere shows that a very high concentration builds up in an unventilated dead end heading. As Holaday et al1 observed, even a minimal air movement results in a drastic reduction in radon daughter concentration. It is therefore obvious that the main objective of radon daughter control in the working environment is to design the ventilation system providing an optimized flow of fresh air into the workplace, resulting in acceptable climatic conditions and achieving radon daughter concentrations resulting in exposures as low as reasonably achievable. BASIC OBJECTIVES Large mining companies, having extensive material resources and professional expertise, have utilized elaborate electrical modelling in the design of mine ventilation systems as early as 1950 (coal mining industry in Europe) and with the advance of computer modelling techniques, their utilization in ventilation systems design is on the increase. Unfortunately, these methods are usually not available to small mining companies and even the large companies might not achieve the fullest benefit from utilizing them, if proper limiting factors are not considered in the modelling. When an evaluation of a ventilation system of a mine is undertaken in literature, a measure of the amount of air supplied underground per one ton of ore mined is used as an indicator of the efficiency of the ventilation system. Yet, even the greatest amount of air forced into the mine might not result in an acceptable working environment if a proper distribution of this air into individual working places is not achieved. The volume and the age of the air are probably the two most important factors in achieving acceptable radon daughter concentrations in the workplace, but other factors also have to be considered. DIRECTOR MINE - ALCAN, NEWFOUNDLAND FLUORSPAR WORKS ST. LAWRENCE, NEWFOUNDLAND, CANADA Ventilation To illustrate the effects of the design of the ventilation system on the control of radon daughter concentration, let us review the gradual development of the ventilation system of this mine from the earlier years of its development up until its final years of operation. This mine, located near the community of St. Lawrence on the south coast of Burin Peninsula was developed in the late thirties and reached full production by 1942. Unfortunately as was customary at that time, the only source of ventilation was a natural draft. The mine was extremely wet, and no significant attention was initially given to possible health effects of dust. It was not until the mid-fifties, when a number of cases of silicosis had surfaced, that de Villiers and Windish2 observed a significant increase of lung cancer incidence among the miners in comparison to its incidence among the general population of Newfoundland. Suspicions regarding radiation as a cause of the lung cancer were expressed, but it was only in surveys taken in late 1959 and early 1960 that Windish3 and Little4 established the presence of radon daughters in the mine atmosphere in very high concentrations. Windish, de Villiers and Hurley suggested that the most likely source of the radon in the mine was the mine water which dissolved radon during its passage through the granitic country rock in the surrounding geological area. This conclusion was confirmed by analyses of water from various areas of the mine by the Atomic Energy Canada Limited laboratories. The radon values in the samples varied from 4,240 to 12,850 pCi/L5. Following the discovery of the presence of radon daughters in the mine, the company took speedy action to install mechanical ventilation for the mine. The system was not designed as a total unit, but fans were installed rather on a trial and error basis. The basic system installation began in March 1960 and was completed by 1962. It remained basically unchanged with only minor modifications until August 1973 when a wholly new, redesigned ventilation system was implemented. A schematic section of the mine and its ventilation system for the period prior to March 1960 is given in Figure "A", for the period 1960-1973 in Figure "B", and for the period after August 1973 in Figure "C". The ventilation system prior to 1960 is not known. All workings of the mine were ventilated only by natural ventilation. If any measurements of airflows at different or any times of the year ever existed, no records have been preserved. The very minimal natural ventilation was augmented by "blowing" air from compressed air supply lines and exhaust air from drills. It is known that the compressor capacities of the mine were limited and therefore no significant air movement was probably created by the "blowing".

Jan 1, 1981

By J. M. Mutmansky

Introduction Since the Hardy Cross numerical algorithm was applied to the solution of mine ventilation networks, numerous developments have taken place in ventilation network analysis procedures. The Newton-Raphson method, the linear theory method and the second-order approximation method are three of the additional approaches that have been applied. The efficiency of a ventilation network analysis procedure depends not only on the method of solving the system of equations derived from ventilation networks but also on the method of deriving the equations through selection of the meshes. This paper investigates the impacts of three mesh selection methods on the efficiencies of four ventilation network procedures. The minimum-resistance spanning tree method is the most popular procedure for selecting meshes. The shortest-path method was suggested by Epp and Fowler (1970) for improvement of the Newton-Raphson method. The minimum-resistance-path method is suggested here as the third method of selecting meshes. The effects of these three methods on the Hardy Cross method, the Newton-Raphson method, the linear theory method and the second-order approximation method are analyzed in this paper. These network analysis methods have been summarized in the paper by Kim and Mutmansky (1991). Mesh selection methods A procedure for mine ventilation network solution based on mesh equations typically consists of two steps: • the mesh selection step and • the network solution step. The mesh selection step establishes a set of independent equations to solve the network. The resulting equations are nonlinear. One method of solving nonlinear equations is to linearize the equations and iteratively solve these linear equations. The four analysis methods previously discussed in this paper use this approach. The linear equations required for solution can be written in matrix form as: P•dQ = dF (1) where P is the pseudo-resistance matrix, Q is the quantity matrix, and F is the Jacobian matrix (Kim and Mutmansky, 1991). The efficiency of the solution method depends on the characteristics of the P matrix, which in turn depend on the method of selecting meshes. To understand the impacts of the mesh selection methods on the efficiency of the ventilation network analysis procedures, the characteristics of the P matrix must be understood first. The diagonal elements of the P matrix, m in number, are the sums of the pseudo-resistances of the branches contained in the m meshes necessary for solution. The off-diagonal elements are the sums of the pseudo-resistances of the branches shared by two meshes. For example, P12 (first row, second column element of the P matrix) is the sum of the pseudo-resistances of the branches common to mesh 1 and mesh 2. When solving the system of equations expressed in Eq. (1), three of the iterative procedures (the Newton-Raphson, the linear theory and the second-order approximation methods) use the direct factorization method (Burden and Faires, 1985) on the P matrix. When the direct factorization method is used, the computational efficiency is enhanced by larger diagonal elements and a sparser P matrix. Generally, the sparsity of the P matrix is more important than the size of the diagonal elements. There is no known mathematical method of predicting the efficiency of these procedures, but heuristic methods can be used to study the efficiency. The Hardy Cross algorithm applies the Gauss-Seidel method of splitting the P matrix and applies the Newton-Raphson procedure. The efficiency of the Hardy Cross method depends on the spectral radius of the matrix[[D-L]-1U], where D is the diagonal, L is the lower triangle and U is the upper triangle of the P matrix for the Newton-Raphson method (Ortega, 1972). The smaller the value of the spectral radius, the faster the convergence. As with the other three methods, larger diagonal elements and a sparser matrix aid in faster convergence. With the Hardy Cross method, however, the size of the diagonal elements is more important than the sparsity of the matrix. Remembering that each of the diagonal elements of the P matrix is the sum of the pseudo-resistances of the branches in a mesh and that each off-diagonal element is the sum of the pseudo-resistances of the branches shared by two different meshes, the following strategies can be used: • Avoid having branches with larger resistance values shared by multiple meshes. This increases the size of the diagonal elements and reduces the chance of off-diagonal elements being large.

Jan 1, 1993

By Peter A. Spencer

Much criticism has been levelled at bacterial oxidation over the quantities of air required for successful operation. Examination of the oxidation reactions and the assumptions concerning oxygen transfer made in the literature (1) indicate that the aeration requirements can be much less than those beirig suggested. Observations made on a large scale pilot test have confirmed reasonable aeration levels in extended site operation over a six month period. These aeration levels have implications for the engineering design and the power needed for aeration and agitation. Thus, these parameters effect both capital and operating costs as well as influencing the complexity of the design and normal operation. A number of companies have developed bacterial oxidation cultures intended for commercial ·expl oi tat.ion ( 2, 3, 4). Most of these cultures have been based on Thiobacillus and operate at temperatures between 30°c and 40°c. This temperature range limits their application in hotter regions unless means for both heating and cooling are provided in the design. Thiobacil!us cultures are also reported as not able to oxidize arsenic (III), which may limit the application of these cultures to successfully treat arsenopyritic ores and concentrates (5). BacTech (Australia) Pty Ltd has developed a culture which operates at temperatures above 4o0 c and which has been tested in a large site based continuous pilot plant at up to 55°c over a six month period. The culture showed resistance to high levels of soluble arsenic, allowing the arsenic to be retained in solution for control led precipitation and disposal. Data for. the arsenic precipitates indicated that these waste solids were relatively stable and, under the correct circumstances, were suitable for disposal into tailings dams without causing environmental problems.

Jan 1, 1990

By Young C. Kim

Because of the high cost of obtaining coal washability samples, it has been difficult to obtain washability variograms in the past. As a result. It could not be determined if geostatistical prediction tool known as kriging can be applied to predict in-situ coal washability characteristics.

Jan 1, 1988

By L. W. Swent

Dr. Emrick, honored guests, distinguished speakers, ladies and gentlemen, I am Langan Swent, Vice President for Environmental Affairs and Occupational Safety and Health, of Homestake Mining Company. Today, I appear on behalf of the American Mining Congress, as chairman of its uranium mine health subcommittee. The American Mining Congress is a trade association of several hundred members, which include the producers of a large proportion of the nation's uranium. I've been asked to make a statement of principles for the uranium industry. There are two types of principles that apply to industry in general, and specifically to the uranium industry. Some have external origins and apply regardless of what industry does or thinks. Others are generated by industry itself and serve as goals for the industry. I'll discuss some of each type. I'll limit my statement to those principles related to the subject of this conference--radiation hazards in mining. I won't take your time trying to explain some of the unrelated principles that we must all contend with, such as Parkinson's Laws, Murphy's Law, and the Peter Principle. First and foremost, industry has a sincere interest in the well-being and health of its employees. There are two basic reasons for this. One is a basic respect for human lives, especially those of people we see and work with every day. No one in management wants to carry the lifelong burden of blame for a life lost due to poor working conditions. Most uranium and other mining is done in small communities. Production workers, maintenance workers, service workers, shift bosses, foremen, superintendents and managers all live in the same community. They attend the same churches. They serve together in civic activities. Their children go to the same schools. If one employee in such a community loses his life due to poor working conditions, those remaining know in a daily and intimate way the resulting personal tragedy, usually of a bereaved widow and fatherless children. This sad experience makes the community, including industry management, intensely sensitive to the need for maintaining good working conditions in the mines. But what about the segment of industry that does not live in the mining communities? Corporate and owner's offices are frequently hundreds of miles from the communities where the mining takes place. Many of these people are not personally acquainted with the workers, and there are few close personal ties between the two communities. The distant staff are, however, still human beings and motivated by the same basic human respect for life. Mr. Manuel Gomez of MSHA and a member of the planning committee for this conference summed this point up expressively when he told me: "No one group has a corner on compassion." In addition to compassion, there is another factor. In both communities the basic assignment to everyone is to produce profits. In carrying out this assignment, supervisory and management people are acutely aware of the high cost of illnesses and accidents. Their objective of maximizing profits is advanced significantly by minimizing illnesses and accidents at the mines. A business that has illnesses and accidents generally suffers from poor employee morale and high employee turnover, both of which detract from profits. Next, I would like to talk about what industry has done in the field that is the subject of this conference. We have worked at all sorts of methods to reduce exposure of employees since the exposure standards were first introduced and then lowered. Other speakers will go into details of technology, and I'll simply comment on exposure results. These are best shown in Table 1. The table shows the average WL to which miners in U.S. underground uranium mines have been exposed since 1937 through 1980. The trend of decreasing radon daughter concentrations throughout the period is obvious. Figure 1 presents this data graphically and shows the trend at a glance. This record begins in 1937 when uranium, as such, really wasn't being mined or sought. The concentrations given by the U.S. Public Health Service were for a few small vanadium mines which carried uranium as a by-product. A few years later, when the Manhattan project to develop the atomic bomb was begun, these mines became the first U.S. uranium mines and the vanadium became the by-product! The radiation hazard then also received attention and the average concentrations began to decline. As knowledge of the reality of the hazard spread, conditions improved. The search for uranium in the U.S. turned up new and larger ore bodies that had to be mined by large underground mines. These mines involved ventilation planning from the beginning, and when they came into production in the late 1950's they lowered the average concentrations greatly. Then in 1960 the American Standards Association adopted a standard setting 1 working level as a satisfactory condition, and several action levels up to 10WL, at which point removal of people from exposure was called for. As a result of the uranium producing states governors' conference in December 1960, state mine inspection agencies, in the early 1960's, began to adopt and enforce the ASA standards. As a result, average concentrations again declined. In 1967, the Federal Radiation Council recommended an annual limitation of 12 WLM per individual. This represented a great change in the methods of

Jan 1, 1981

By B. V. Close

Surface mining regulations together with mine and reclamation planning require collection of large amounts of geologic and hydrologic data for both new and existing mines. Recently developed microcomputer software facilitates the integration of this information from computer databases into ground-water flow models. The databases are used to identify areas which require dewatering and/or depressurizing and for generating contour maps of aquifer parameters. Gridded versions of these contour maps are incorporated into finite difference ground-water flow models which are used to design dewatering and depressurizing well fields and to estimate the effects of ground-water pumping and pit progression on local ground-water levels.

Jan 1, 1988

By Arnolfo A. Valdivia

Prior to 1971, there were several clinical trials to evaluate programs for early detection of lung cancer. Among these, the Philadelphia Pulmonary Neoplasm Research Project,(3) the Veterans Administration Study published by Lilienfeld,(7) and the controlled trial of the Kaiser Foundation Health Plan showed an overall five year survival rate of 8% for newly detected cases (the same as the national statistic for unscreened patients). In 1971, the National Cancer Institute initiated three randomized, controlled mortality studies using lung cancer screening of persons at high risk (male smokers over 45 years old). The studies are being conducted at the Johns Hopkins University Hospital, the Mayo Clinic, and the Memorial Sloan-Kettering Cancer Center. The studies have slightly different designs in the combination of sputum cytology and chest x-rays. At the Mayo Clinic the study group is offered screening with sputum cytology and chest x-rays every four months, whereas the control group is advised to have an x-ray and cytology every year. No reminders are sent, and it is believed that only about 20% of the control group is screened. At Johns Hopkins and Memorial, both experimental and control groups are offered annual chest x-rays. The experimental group is additionally offered sputum cytology every four months.(5) At present all of the programs show that screening can detect cancers that are undetectible by other means. However, at this time mortality rates in the control and experimental groups are not significantly different in any of the three studies. OUR PROGRAM Our clinic is located in Grants, New Mexico and we provide most of the pre-employment physical examinations for the mines operating in the Grants area (Kerr McGee Nuclear, Homestake Mining, United Nuclear, Western Nuclear, and Ranchers). In the examinations, we obtain the previous mining history of the worker, a chest x-ray, a sample of sputum for cytological examination, and a blood sample. We also provide routine annual physical examinations of the workers, with special interest in the detection of bronchogenic carcinoma. In the early seventies, we did not have a definite surveillance program. We did not know whether we should have a program like the one started at Memorial or like the one started at the Mayo Clinic. After long consideration, we decided to have a program that does not demand a sputum cytology and chest x-ray every four months, but that allows as many chest x-rays and sputum cytologies as needed to diagnose lung cancer as early as possible. We believe that, if a screening method for cancer is to be optimally effective, it must detect the process at stages early enough for curative therapy. We order a test depending on the age of the miner, the race, the mining history, the smoking history, the radiation exposure levels, and the results of the previous chest x-ray and sputum cytology. With the help of the computer, we have a list of all the miners who should be watched closely because of age, race, mining history, smoking history, radiation exposure, etc. Examination of the miners is performed at our clinic, where all the records are kept. The sputum is collected there but examined in Grand Junction, Colorado, by Dr. Geno Saccomanno. There are two ways to collect sputum. The best way is to collect three consecutive morning samples. For this, we need the cooperation of the miners. They have to follow these instructions and mail the bottle containing the sample to Grand Junction. "Instructions for obtaining a good cough specimen" The enclosed plastic bottle contains a preservative solution, so do not empty out the liquid in it. When you go to bed, place the plastic bottle at your bedside where it will be handy in the morning. When you first get up in the morning (before breakfast) try to cough up some "phlegm" from deep in your chest, and spit it into the liquid in the bottle. Try coughing several times. If you have difficulty coughing, try inhaling deeply the steam from a teakettle (or home-type inhalator). Keep the amount of saliva (ordinary spit) that you put into the bottle along with the cough specimen as small as possible. Do not collect the "phlegm" or mucous that comes from the back of your nose. Put the cap back on the bottle, and shake it vigorously for two minutes. If the amount of material you have coughed up is quite small, then keep the bottle at your bedside for three or four days, and each morning try to add another cough specimen. After obtaining your cough specimen, repack the bottle in the mailing container, and attach the enclosed mailing label. It does not require any postage stamps. Unfortunately, some miners "forget" to mail the sample and end up with an incomplete physical examination. To avoid this some companies, like Homestake, request that we obtain the sample in our clinic by forcing cough and expectorant with a nebulizer machine. This method does not give as good a sputum sample as the previous one, but we do get a sputum sample for every miner. The policies of different companies, in regard to annual physical examinations are different. All

Jan 1, 1981

By A. S. Paschoa, A. W. Nóbrega

INTRODUCTION There are now over twenty years since the radiological characteristics of the brazilian regions of Araxá, Tapira and Barreiros, three locations adjacent to each other, in the state of Minas Gerais, Brazil, started being surveyed by investigators from the Instituto de Biofísica da Universidade Federal do Rio de Janeiro (IB/UFRJ), Pontifícia Universidade Católica do Rio de Janeiro (PUC/RJ), and New York University (NYU) (Roser and Cullen, 1958; Cullen et al, 1980). The importance of the Araxá apatite – Ca5,(P04)3(OH, F, Cl) - and pyrochlore - NaCaNB206F - for the production of large quantities of fertilizers and niobium was early recognized (Roser and Cullen, 1958). Interesting data have been gathered and published throughout the years on the contents of naturally occurring radionuclides in geologic materials, soils, grass, foods and waters of the Araxá region (Eisenbud, et al., 1964; Penna Franca, et al., 1965a, b; Roser et al., 1966; Penna Franca et al., 1970; Cullen, 1977; Penna Franca, 1977; Cullen and Paschoa, 1978; and Cullen et al., 1980). The radioactivity of the Araxá region is associated with mineral deposits of niobium rich pyrochlore and phosphate rich apatite. There are in this region mineral ores with 3 to 5% pyrochlore with 2 to 2.5% Th as Th02 and 50 to 150 ppm U308 in the matrix, while the apatite deposits contain up to 150 ppm U308 and a thorium concentration similar to that of the pyrochlore deposits (Paschoa and Palacios, 1981). As an indication of the high thorium content of the Araxá soils the 228Ra and 224Ra activity concentrations were reported to range from 10.6±0.2 to 62.4±0.7 pCi228Ra/g soil in 7 samples and 2.1±0.1 to 104±1 pCi224Ra/g soil in 19 samples (Cullen, et al., 1966). The uptake of radium isotopes by edible roots vegatables and fruits growing in the soils of the Araxá region can be illustrated by the data listed in Table I. The biological availability of natural radium isotopes in some segments of the Araxá soil allows a large variation in the 228Ra, 224Ra and 226Ra concentrations in vegetables and edible roots, as can be seen in Table I. This fact makes quite difficult a quantitative local assessment of the radiological implications of mining the Araxá mineral deposits of pyrochlore and apatite for production of niobium and phosphate fertilizers, respectively; since one cannot easily separate the naturally occurring from the technogically enhanced radionuclide contents of foods. The position of the city of Araxá inside the contour of the state of Minas Gerais appears in the upper part of Figure 1, which shows the outlined map of Brazil with the positions of the cities Brasilia and Rio de Janeiro also indicated. The lower part of Figure 1 is a representation of the Araxá region in an expanded scale, which indicates the locations of the pyrochlore and apatite deposits in relation to the city of Araxá, as well as the nearby hydrographic basins. The distance between the city of Araxá and the pyrochlore deposit is about 8 km, and between the pyrochlore and apatite deposits is 4 km. This paper deals tentatively with the radiological implications of the industrial operations taking place in the Araxá region for the exploration of the pyrochlore and apatite deposits. However, one must bear in mind, firstly, that the radiological implications of these industrial activities are by far too complex to be covered adequately by the limited amount of data to be presented in this paper, and secondly, that such implications cannot be considered of local character only. INDUSTRIAL OPERATIONS The commercial exploration of the Araxá deposits of pyrochlore and apatite started only few years ago, motivated by the increasing demand of niobium and phosphate fertilizers in Brazil and the world. As a consequence of the industrial operations in Araxá, a redistribution of the uranium, thorium, and radium originally present in the local deposits of pyrochlore and apatite started occurring in the seventies, with possible radiological implications for the Araxá region and its immediate surroundings, not to mention the destinations of the end products of such industrial operations. A literature review on the radioactivity associated with the extration industries of selected minerals was made by the USEPA (Bliss, 1978). The low level radioactive wastes of the industries for copper ore mining and rare metals processing have been object of particular attention (Fitzgerald, Jr., 1976; Eng, et al., 1979), but the short and long term implications of the radioactivity associated with the niobium industry were also subjects of concern (Knight and Makepeace, 1978). Recently, high 232Th and 226Ra concentrations in samples from the tin mining industry in West Malaysia were reported (Hu et al., 1981). A great deal of attention has been dedicated to the implications of the redistribution of radionuclides originally present in the mineral ores used by the phosphate fertilizer industry (Moore, 1967; Menzel, 1968; Spalding and Sackett, 1972; Eisenbud, 1973; Guimond and Windham, 1975; Guimond, 1976; Roessler,

Jan 1, 1981