Search Documents

By H. A. Kortmann

Blast furnace operators have been steadily increasing their quality requirements on burden material. These requirements include a high reduction rate of the ore burden as well as good strength at the beginning and during the whole blast furnace operation. Special requirements are made on the softening and melting behavior which ensures an optimal formation of the cohesive zone in the blast furnace. On the whole, the self-fluxed and olivine-based pellets meet these higher requirements due to their chemical composition, especially in the pure pellet operation. In the mixed sinter/pellet operation partly-fluxed and acid iron ore pellets can be appropriately used. The paper describes the demands on, and characteristics of, different kinds of pellets used in the Federal Republic of Germany.

Jan 1, 1989

By P. J. Lechler

A review of the geology and mineralogy of several of the better known hydrothermal platinum-group metal (PGM) deposits is undertaken. Along with new data from two recently discovered occurrences in Nevada, a number of common characteristics of these deposits are identified. Newly described PGM occurrences in Nevada are the abandoned Gibellini mine workings characterized by limestone-hosted hydrothermal Mn-V-Zn-Ni mineralization and the granite-hosted base-and precious-metal veins of the Gingerload claims.

Jan 1, 1989

By R. L. King

An expert system is a computer system that performs tasks that are considered by most people to require human expertise. Since their functioning relies heavily on large bodies of knowledge, they are often referred to as knowledge-based systems. These systems can contain the skill and knowledge of an individual human expert or the combined knowledge of a group of experts. The knowledge embodied in an expert system can consist of specific facts, HSHA regulations, heuristics or rules-of-thumb used by the expert, and databases. The purpose of this paper will be to introduce the participants in the ?Increase Competitiveness Thru Innovation? session to expert systems. This introduction will enable the participants to better appreciate the balance of the papers to be presented in this session. These papers will deal with specific mining problems and a proposed innovative solution. This paper will discuss such topics as problem-solving paradigms, rules of inference, knowledge representation, and the structure of expert systems.

Jan 1, 1989

By K. A. Sauer

Blasting can create severe interference for a mine's carbon monoxide based fire detection system. At the present time, without being able to differentiate between blast and non-blast carbon monoxide, a fire detection system must either set fairly high alarm levels for its sensors, or allow frequent "false" alarms to sound during blasting. This paper will introduce current work being done which will attempt to define characteristics of the carbon monoxide concentrations time curve for blasting. The work uses drift blasting for its data base as it is one of the more common forms of blasting. Future work with the data may produce a mathematical model which can be used to monitor and identify the carbon monoxide time curve for drift blasting.

Jan 1, 1989

By William Hustrulid

INTRODUCTION The Idarado mine lies high in the San Juan Moun¬tains on the divide between the Uncompahgre and San Miguel Rivers and consists of a consolidation of a number of old and prominent mining properties through which course some famous and very produc¬tive veins. Among the better known are the Smuggler, Tomboy, Montana-Argentine, Black Bear, Liberty Bell, Virginius, Flat, Barstow, and Japan, as well as many others. Most of these veins have been extensively mined over the past century and in the last three decades the Montana-Argentine and Black Bear veins have been the backbone of the Idarado mine; therefore, the descrip¬tion of the veins is limited to them. Access to the mine is through either the Treasury tunnel, whose portal is below Red Mountain Pass on US Highway 550 at an elevation of 3244 m (10,643 ft), or the Mill Level tunnel entrance 3.2 km (2 miles) east of Telluride, CO, at an elevation of 2761 m (9060 ft). The Treasury tunnel intersects the Black Bear vein 2643 m (8670 ft) from the portal and the Mill Level tunnel intersects the Argentine vein 2179 m (7150 ft) from the portal. Mining is by shrinkage stoping from slusher sublevels. The size of the scope blocks varies somewhat, but the standard size is 67 to 76 m (220 to 250 ft) long and 61 to 76 m (200 to 250 ft) high. The mine ranks either first or second in Colorado in yearly production of gold, silver, copper, lead, and zinc. It is 9.6 km (6 miles) from the Red Mountain plant to the Pandora plant, via interconnecting drifts and raises. There are engineering offices at both plants as a matter of convenience. The Red Mountain plant in¬cludes the company general offices, warehouse, carpen¬ter and machine shops, and mine change room. The Pandora plant consists of the mill and assay office, ma¬chine shops, and mine change room. The flotation mill has a capacity of 1632 t/d (1800 stpd), making a bul¬lion product and separate concentrates of lead, copper, and zinc. HISTORY OF THE MINE The Montana-Argentine vein was first extensively worked by the Tomboy Gold Mines Co., Ltd., a British concern. This company mined the stoped areas above the Ophir level between 1910 and the late 1920s and most of the stoped areas above the 2100 level between 1900 and the late 1920s. Gold was the principal ore metal mined. The area between the Revenue and Ophir levels was mined chiefly by the Revenue Mines Co. between 1900 and 1910. The ore was worked from the Revenue tun¬nel, which portals in Canyon Creek. Gold and silver were the chief metals recovered. The stopes between the 1700 and Revenue levels, as well as some higher stopes, were mined by Telluride Mines Inc. during the 1940s. The Mill Level tunnel was driven by that company from 1945 to 1948. Lead and zinc then became economically more important than the precious metals. In 1953, Idarado purchased Telluride Mines, which merged with the parent company in 1956. The Black Bear vein was first extensively worked by the Black Bear Mining Co. in the 1900s and by the Colorado Superior Mining Co. from about 1914 until snowslides at the mine camp [altitude 3750 m (12,300 ft)] terminated the company's operations in 1924. Leasers operated at intervals until 1934. The Treasury tunnel, formerly the Hammond tunnel, had been started before 1900 and reached the 1646-m (5400-ft) mark early in the 1900s, at which time activity lagged until the late 1930s. In the early 1940s, Idarado extended the Treasury tunnel from its heading at 1646 m (5400 ft) to the Black Bear vein and established a raise connec¬tion with the 600 level, the lowest level in the old mine. Since completion of initial work in the mid-1940s, systematic development of the mine, both in the driv¬ing of new headings and the utilization of older open¬ings, has resulted in the present extensive network of workings. GEOLOGY Introduction The oldest rocks of the area are the Precambrian metamorphic rocks, the Uncompahgre formation which are massive quartzites, some phyllites and slates, and dolomitic or limestone beds. West-dipping Paleozoic and Mesozoic strata lie on the Uncompahgre formation. These units are separated by a major angular uncomformity from overlying, essentially horizontal, Tertiary formations that include the basal Telluride conglomerate and several thousand feet of overlying volcanic rock. Intrusive rocks, mostly Tertiary in age, are common in the area, and are in the form of dikes, stocks, and sills. Dikes are very closely associated with some of the ore veins (Mayer). Description of Veins The Black Bear and Argentine veins range from 0.6 to 7.6 m (2 to 25 ft) in width, but in most places are 1.5 to 2 m (5 to 7 ft) wide. They vary in character from a well-defined tabular structure between sharp "frozen" walls, or gouge seams, to an irregular zone of quartz and quartz-sulfide stringers. Many gouge seams within the veins make the veins blocky and loose. Common gangue minerals in the veins include quartz, pyrite, rhodonite, chlorite, sericite, clay minerals, epidote, calcite, adularia, rhodocrosite, fluorite, and specularite. Quartz constitutes 60 to 70% of the veins and varies widely in character, ranging in color from clear through white, gray, and green, to amethyst. Chlorite, sericite, the clay minerals, and fine-grained quartz are common alteration products of the vein walls and of wall rock fragments in the veins. Epidote is an altera¬tion of the dike or, less commonly, of tuff-breccia. Calcite, adularia, fluorite, and rhodocrosite, which are wide¬

Jan 1, 1982

By Fred N. Kissell, George H. Jr. Schnakenberg

INTRODUCTION A variety of instruments are available for measuring or monitoring the performance of underground mine-ventilation systems. In general terms, the instruments may be classified as those that measure air velocity and those that measure gaseous concentrations. All costs herein are in terms of 1978 US dollars. The mention of a specific manufacturer or device is not intended to be an endorsement by the US Bureau of Mines. AIR-VELOCITY INSTRUMENTS The basic instruments used for measuring the air velocity in mines are the vane anemometer and the smoke tube. Vane Anemometer Of the air-velocity instruments, the 102-mm (4.0¬in.) vane anemometer is the most common and is available as either a low- or high-speed type. The low-speed anemometer generally is the most suitable for measuring the velocities in ordinary airways. For a rough check of the velocity in an airway, it usually is satisfactory to hold the anemometer by hand, positioning it in the center of the airway for 30 sec. However, the resultant error may be as high as 25% , and such a hand-held approach is unsuitable when accurate or reliable measurements are required. To obtain more accurate measurements, the proper procedure is as follows: 1) Since holding the anemometer by hand generally causes the instrument to read about 15% high, it is mounted on a 0.6-m (2-ft) extension rod. 2) The airway is divided into equal right and left halves. A 1-min traverse is used in each half, moving the anemometer smoothly up and down in a zigzag pattern so that the entire half is covered within the allotted minute. 3) The manufacturer's correction table is applied to the readings to adjust the velocity calculation as necessary. Whenever possible, anemometer readings should be obtained in a long straight section of airway that has a constant cross-sectional area. Bends and obstructions should be avoided, since they cause turbulence and other discontinuities in the airflow and can degrade the accuracy of the velocity measurements. Although a series of velocity measurements at one location usually corresponds to within a few percent, this is not an indication that the airflows calculated from those readings are completely accurate. One reason is that the correction table provided with the instrument generally is not for that specific instrument; instead, it represents the average correction for all such instru¬ments made by the particular manufacturer. Most cor¬rection tables specify a correction factor of from 0 to 15%, depending upon the velocity. However, even after correction, the instrument error still may range from 3 to 5%. At low velocities such as those below 0.76 m/s (150 fpm), the instrument error can be two or three times greater than this, ranging from 6 to 15%. The new ball-bearing anemometers generally perform somewhat better at low velocities than did the older conventional anemometers. Another source of error is introduced when measur¬ing the cross-sectional area of the airway or entry. Under the best of circumstances, measurement errors, instrument errors, and a host of other minor errors all combine to cause a total error of at least 10% in the velocity calculation. The vane anemometer also can be used with reason¬able accuracy to measure airflows in mine-ventilation ducts. In this application, the anemometer is mounted on a rod and is held at the center of the duct end. For a duct that is discharging air, the average velocity in the duct is 85% of the centerline reading (Northover, 1957). For a duct that is taking in air, the average velocity is 70% of the centerline reading (Haney and Hlavsa, 1976). To measure the airflow discharged from a regulator or from a small hole in a stopping or bulk¬head, a correction factor for the area is necessary. A good approach in this situation is to traverse the area of the regulator or hole, holding the anemometer with an extension rod. This provides an average velocity that is multiplied by 85% of the measured area of the regulator or hole. In all cases, the manufacturer's instrument cor¬rection table must be used and applied properly. For accurate results, the anemometer should be returned to the manufacturer for periodic cleaning and checking. If it is in daily use, the anemometer should be returned about once per year, and proportionally less frequently if the usage is less frequent than on a daily basis. Smoke Tube The smoke tube may not appeal to individuals who believe that good measurement results can be obtained only with expensive, complicated, and fragile instru¬mentation. Nevertheless, smoke works about as well as anything for the routine measurement of low air velocities in mines. The following procedure yields reasonably good results: 1) Two marks are scratched 7.6 m (25 ft) apart on the floor of the airway. 2) The smoke tube is used to release a cloud of smoke in the center of the airway, about 0.9 m (3 ft) upstream of the first mark on the floor. 3) A timed interval begins when the leading edge of the smoke cloud passes over the first mark, and the interval stops when the leading edge of the cloud passes over the second mark. 4) A factor of 20% is subtracted from the cal¬culated velocity to determine the true average velocity, providing a correction for the centerline and for the spreading effect at the front of the cloud. Velocities calculated with the preceding method generally are accurate to within 10 to 15%. In some instances, the cloud from a conventional smoke tube

Jan 1, 1982

By R. W. Guill

For the past five years, Small Mine Development has been involved in the development of small grade underground projects. These projects have been in tough environments where solutions have been found by placing emphasis on creative collaborations by small work forces and selected specialists. This has created an environment where constant innovation and change have become standard operating practice. The cornerstones of these efficient operations have been formed using pneumatic backfill, creative shotcreting, specialized equipment, and highly motivated people. The results realized have served to turn interesting properties into productive operations.

Jan 1, 1988

By B. J. Arnold

Over 600 million tons of coal are handled annually for use by the country's coal-fired power plants. Coal is transported in various ways. overland conveyors. Railcars, trucks, and barges. It can travel short distances or thousands of miles, picking up moisture, freezing, or drying. When the coal is received at the power plant, environmental problems with fugitive dust and further handling problems can arise.

Jan 1, 1989

By A. W. Khair

This paper presents an assessment of modeling techniques in predicting subsidence over longwall areas. Extensive instrumentation, both at the surface and subsurface of three longwall mines in northern West Virginia have been made. Ground movements were monitored during" a three year-period until subsidence ceased in these areas. A comparative analysis of empirical subsidence prediction techniques including, graphical {NCB}, profile function, influence functions (USBM, BAL'S, KNOTHE'S, and zone area) will be presented. A brief geologic and topographic description of each site along with the instrumentation and monitoring program will also be presented.

Jan 1, 1989

By M. R. Rosen

CARBINDER Polymer 498 is a liquid organic taconite binder which significantly improves fired compression in both fluxed and acid pellets. It has been used commercially in both shaft and straight grate furnaces. This new binder produces an unusual wicking phenomenon during balling wherein the rate of movement of interstitial water is accelerated to the surface of the balls. The phenomenon is proposed to be responsible for the significant improvement seen in fired compression. This paper presents information as to the effect of CARBINDER Polymer 498 on green ball and fired pellet properties. It also describes the wicking phenomenon and discusses a reversal in the normal balling operation procedures required for successful agglomeration.

Jan 1, 1988

By M. L. Clark

Advances in the recovery of gold from heap leaching are being made daily, but of all the systems vital to the maximum recovery of gold from a leach pile, none is more important than the methods used to construct the pile in preparation for the leaching operation. The technology described in this paper illustrates the latest systems developed to minimize compaction in the pile during its construction and reduce the cost of placement of ore on the pile. The Florida Canyon Mine of Pegasus is evaluated in detail to show reasons for its high degree of success to date.

Jan 1, 1988

By R. L. Beatty

The Bond International Gold (BIG) Colosseum Gold Mine was discovered in 1865, but no recorded production occurred until the 1930's, with production approximately 19k9 (615 oz) of gold. The mine was closed in 1942 as a non-essential industry during World War II. The property was acquired by Dallhold Resources in mid 1986. Construction of a 1.1 million Mt carbon-in-pulp, cyanide mill started in November, 1986, and was completed in September, 1987. Minable reserves are estimated to be 9,560,831Mt (10,539,000St), with an average grade of 2.1 g/Mt (0.062 oz/st). This paper describes a general view of process flow and plant equipment, as well as a look at the maintenance and operational problems encountered in the fist six months of operation.

Jan 1, 1989

By David D. Eyer

Since the decade of the 1990s is nearly upon us, I have focused on what I see are the likely trends featured in new large underground coal mines 10 years from now. I do this from the vantage point of having been involved in the installation of large mines for more than twenty years. Little of the equipment resources we have available today was unknown when I entered the coal business in 1960. There were continuous miners, longwalls and diesel-powered equipment in Europe, monitoring systems, computers, heavy media separation systems, froth flotation and conveyors then as there are now. A substantial evolutionary process has occurred with these and other mining machines and processes. Some evolved only to die out, such as boring-type continuous miners; others, such as longwall systems, flourished. My intuition tells me that since there have been largely evolutionary rather than revolutionary developments in the near past, the same is true of the future, at least for the next 10 years. In other words, the elements of what are in the future are with US now. Some, such as computer-based applications, may evolve beyond our wildest dreams -but I doubt it.

Jan 1, 1988

By L. W. Laage

Throughout recorded history, underground fires have plagued mining operations. Compared with other hazardous situations in underground mining, a fire can become a global problem by swiftly spreading deadly carbon monoxide and other products of combustion (POC's) throughout the whole mine, often without warning. Experience has shown that when fires are detected and located in their early stages, they are much easier to control and proper escape routes can be more intelligently selected. Recent advances in sensor and data communication technology have made reliable mine fire .detection system installations possible. Unlike building construction. in a mine, it is impractical to install detectors at every desired location. Abandoned workings and unsafe locations preclude sensor installations from both safety and economic standpoints. The net effect is that some fires are detected and located early while the location of others, even if detected early, remains unknown too long for effective evacuation and fire fighting.

Jan 1, 1989

By M. R. Fletcher

Slags generated by the ferrous-metals industry can be used to produce high-tech ceramic materials. The properties of these ceramics can be controlled by judicious choices of composition, additives, and processing parameters. Standard methods of materials handling, such as comminution and mixing, are as applicable to slag as to any other mineralogic raw material. In this study, foundry slag was ground, homogenized, melted and formed to produce a glass, and then heat treated to crystallize it into a high-strength glass-ceramic. The product shows promise as a low-cost wear-resistant tile material which can be custom cast. This and similar materials, made from slags and natural rocks, are candidates for use as construction materials, acid-resistant piping, shock-resistant sheathing, rot-proof pilings, and, when foamed, even as pontoons.

Jan 1, 1988

By B. C. Williams

The Bureau of Mines monitored the water quality in and near a copper/gold tailings impoundment. Samples were taken from the unsaturated %one. and dissolved concentrations of over ZO constituents were measured with respect to depth and moisture content, factors which influence oxygen content and sulfide oxidation. Samples from the unsaturated %one were drawn through a hypodermic needle sampler into individually evacuated vials fitted with septa, thus preventing oxygen contamination. Water quality was also monitored in the saturated tailings, underlying colluvial aquifer, and weathered andesite bedrock.

Jan 1, 1989

By M. Lotfi

The criteria for evaluating equipment operator performance were identified as the changes in reaction time, the changes in physiological responses, and the changes in subjective reporting of stress. Data were collected while the Subjects operated a front-end loader simulator. This report out-lines the components and the tasks generated by the simulator. It explains the simple and basic assumptions underlying the design of the simulator and the methods of data collection. Improvements that can facilitate the collection of data, including the connection of the simulator to a portable personal computer for on site use are discussed. Statistical analysis of data showed significant deterioration in performance. The report concludes that operator performance can be measured and improved. This report shows that the operator tasks can be simulated by means of simple simulators, the complexity of which is determined by the availability of funds and the area of interest of the investigator.

Jan 1, 1989

By W. Hu

Traditionally, coarse wolframite ore processing has been done almost exclusively by gravity concentration methods. However, there has been a depletion of rich and coarse ore reserves and a proportional increase in the mining of low-grade, fine-grained complex ore feeds. This change has resulted in the need for better slime-processing technology. Research and development activities in this area have gained momentum, and recent innovations appear promising. This paper covers the recent innovations that have been made in dealing with tungsten ore slime processing. The new techniques include the application of a centrifugal cone separator, high-intensity wet magnetic separator, the use of phosphonic and arsonic acids as collectors in ultrafine wolframite flotation, and combined processes.

Jan 1, 1989

By R. J. Roman

During the refining of primary magnesium metal: a spent flux (sludge) is produced which is considered a dangerous waste by the Washington State Department of Ecology. Four years of research, testing and marketing has identified two beneficial markets for the spent flux: 1) as a fertilizer and soil admendment as a result of the material's high potash and nitrogen content and its high lime equivalence and 2), as a roadway deicing agent to clear roads of ice and snow as a result of both the salt content and the flux containing chemical compounds which exothermically react with water.

Jan 1, 1988

By D. A. Rice

As part of a cooperative effort between the U.S. Bureau of Mines and the Florida Institute of Phosphate Research (FIPR), with input-from the phosphate industry, the conversion of phosphor-gypsum to sulfur is being investigated. The proposed process incorporates a thermal reduction of phosphogypsum to calcium sulfide (CaS) and a hydrometallurgical treatment to convert calcium sulfide to ammonium bisulfide (NH4SH), which is then oxidized using a catalyst to produce elemental sulfur. The paper summarizes the results of continuing laboratory studies using an activated carbon catalyst which was loaded with sulfur through oxidation of ammonium bisulfide solution. The extraction of the sulfur that forms in situ on the catalyst is a key area in the development of the sulfur recovery process. Two approaches for removing the sulfur are being investigated: 1) thermal treatment to volatilize sulfur, and 2) leaching the sulfur using liquid anhydrous ammonia. The research has shown that it is technically feasible to recover over 90% of the sulfur from the carbon by either volatilization or ammonia leaching. Locked-cycle testing has demonstrated that the carbon has the potential to be recycled after ammonia leaching.

Jan 1, 1988