Search Documents

By Scott G. Britton

Microcomputeranalysis has long been a technique for engineering professionals to improve the theoretical and practical design of continuous mining systems. Such work has been typically composed of modeling observed events and then introducing a variety of known elements with predicted results to compare against the results of the model. Programs written in BASIC, Cobol, Fortran or other language dominated such efforts. These programs have taken years to develop and prove out. This article explores a new management tool used daily at Tanoma Mining Co. (TMC) to track and improve continuous mining systems through the use of microcomputers and Lotus l-2-3 software. Data provided by section foreman, shift foreman, and maintenance personnel are analyzed against predetermined goals. In this way, new production targets are developed, weaknesses in the current mining systems are identified, and the results of changes are measured. The current results of this system on the productive output of TMC systems is on the order of 10% improvement. Thin seam coal mining is an industry within the broader industry of coal mining. Thin seam mining faces the same cost pressures and engineering problems as its higher-seam competitors without the advantages of moving volume per foot of extracted material to stay at an economic parity with others requires additional creativity within the management teams to extract higher productivity gains from the existing workforce and mining systems. TMC operates a deep mine in Indiana bounty, PA, about one hour northeast of Pittsburgh.

Jan 1, 1991

By J. D. Miller

Contact time during bubble/particle collision is calculated by taking into considera¬tion the effect of bubble and particle motion, buoyant force, bubble size, and particle size and specific gravity density for different cases of collision. From this motion analysis approach for the prediction of contact times and from bubble attachment-time measurements,, fundamental aspects of flotation such as flotability, kinetics, and separation can be explained and are discussed with respect to the effects of bubble/particle motion, bubble size, particle size, and attachment time.

Jan 1, 1987

By Carlos Kovacs-Figueroa

Because of air pollution control regulations in the early 701s it became necessary to clean effluent gases from the Morenci Reduction Works Smelter. Feasibility studies indicated that this could be accomplished most efficiently by using the smelter gaseous effluent to feed a sulfuric acid plant. Complying with air pollution control regulations thus created the need to dispose of relatively large amounts of concentrated sulfuric acid. Typical Morenci ores contain substantial amounts of oxidized copper minerals which are not recoverable by flotation. In addition, there is low sulfide, high oxide material which can be leached, but is not suitable for flotation concentration. Early in 1971 sufficent data had been accumulated to show that a leaching plant for the Morenci tailings could use a large portion of the sulfuric acid produced by the Smelter. It was determined that for all practical purposes leaching of the available copper was complete in two hours or less. Capital expenditures could not be justified for more than two stages of counter current decantation for recovery of the leached copper, and the plant was designed with these criteria in mind.

Jan 1, 1976

By Charles H. Minott, Michael J. Markow, Robert D. Wyatt, Fred Moavenzadeh

The substantial investment in tunnels anticipated in the next twenty years has focused new attention on the economics of tunnel construction itself and on some costly problems associated with underground work: the uncertain geologic conditions, the performance and adaptability of men and equipment, and the need for quicker, more efficient excavation methods. There also exists a need to develop better ways of estimating tunnel construction. Inaccuracies in current bid estimates stem from a number of causes, among them (1) the effects of geologic conditions, which are not adequately known prior to construction, (2) the dependence of actual cost on the construction method used and on the interactions among the operations occurring underground, and (3) the reliability of tunneling equipment. Inability to estimate final costs for conventional tunneling more accurately has in turn caused difficulty in gauging the costs and benefits attributable to new tunneling technologies either under development or for which R&D programs are planned. ATTRIBUTES OF THE TUNNEL COST MODEL This paper presents a computer based Tunnel Cost Model (TCM) which quantitatively assesses the uncertainties inherent in underground work, and is detailed enough to aid in preparing estimates or bids. The model employs appropriate techniques of subjective (or "degree of belief") probability and computer simulation of tunnel construction operations to estimate distributions of total tunnel

Jan 1, 1974

By David R. Maneval

At the turn of the century the keys to industrial success were coal and iron. At that time, Pennsylvania was the ranking mineral producer among the States and close to 90% of the Nations energy output was generated by coal. The growth of this Common-wealth into the greatest industrial State in the nation has been due to the huge resources of easily accessable coal found by the early settlers. It was the development of these deposits that provided the United States with a new source of fuel energy. For nearly a century, the Commonwealth was the chief powerhouse of our nation and the chief source of its industrial blood and bone. In 1928 it was truly said that coal was king in Pennsylvania. Pennsylvania that year mined a billion dollars worth of coal. A single train carrying this output would reach more than twice around the world at the latitude of Pennsylvania. Coal formed nearly 67% of the freight of Pennsylvania and was responsible for its four billion dollar iron and steel industry. Coal was the real reason why Pennsylvania although 32nd in size was second and not tenth or fifteenth in wealth, population and industry. Pennsylvania was slow to take-up her heritage as the greatest coal producing State in the union. But the knowledge that coal was present was not slow in accumulating. In fact the Indians were aware of its existence long before the white man arrived. They knew that many of the hills were underlain with black stones that would burn. It is reasonably certain that Arnold Viele, the first white man to cross the mountain in this State saw coal in them in 1692. But awareness was not enough. The population in these days was confined to southeastern corner of the State and the population at this time had little need or interest in the resources further inland. Pennsylvania anthracite was discovered in 1762 but was first regarded only as a curiosity. Commercial productions started in 1820. This stimulated the development of many native industries and extensive canal system and afterwards an elaborate net-work of railroads were constructed at great costs to bring the products of the hard

Jan 1, 1971

By R. Kealey, D. Huo, Q. Zhang, Y. A. Sari

Greenhouse gas (GHG) emissions from primary mineral and metal production account for ~10% of global GHG emissions. One of the main sources of GHG emissions in mining operations is fuel consumption by haul trucks. Given their size and carrying capacity, the fuel consumption of haul trucks can approach 250 liters per hour. An average of 30% of the idle time of the trucks is spent while waiting in the queue. Inefficient truck dispatch planning can waste resources, cause dilution and elevate GHG emissions. In this research, a machine learning based truck dispatch approach was developed to dynamically route the haul trucks based on the loaded material, the road traffic, the estimated wait time, and the maintenance needs of the trucks. The GHG reduction potential of this smart fleet management approach was estimated by calculating and comparing the related carbon emissions versus scenarios using traditional fleet allocation approaches. Results suggest that this dynamic fleet allocation approach can significantly reduce GHG emissions at mineral production sites by optimizing waiting times and the overall distance travelled while achieving the same production levels.

Mar 2, 2022

By H. M. Thorne

Industrial shale-oil operations in North America and Europe predated the Drake discovery, but, since then, most have succumbed to competition from petroleum. However, the existence of enormous oil-shale resources in the Green River formation of Colorado, Utah and Wyoming [estimated at over a trillion bbl of shale oil in place] and the advancement of United States oil- shale technology by research and development programs of government and industry during the past 15 years point to a natural partnership of petroleum and oil shale to meet the accelerating energy demands of the future. The utilization of oil shale is not a question of limited petroleum supplies, but one of economics. Two factors are expected to improve the economic outlook for industrial shale oil production -- a rise in petroleum replacement cost and further advances in oil-shale technology.

Jan 1, 1963

By B. J. Arnold

During the past three years, coal samples covering a range of coal rank, ash content, size consist, grindability, and moisture content have been tested for their flow properties using a triaxial shear tester that measures the unconfined yield strength in a compressed sample of coal. The ratio of this unconfined yield strength to the sample bulk density is part of the equation used by handling system manufacturers to calculate the critical arching or critical ratholing diameter needed to ensure that coal will flow from bunkers or bins. This ratio also serves as an index to compare the flow tested. To test the applicability of the index to predicting problems with coal flow, a series of tests were conducted at CO Inc.'s Coal Quality Development Center (CQDC) in Homer City, Pennsylvania. Tests covering ranges in size consist, moisture content, and ash content were conducted by first filling a small two-ton bin with coal and then emptying the bin at a pre-set discharge rate. The actual discharge rate from the bin under the various conditions tested was measured. Samples of the coal discharging from the bin were collected. One sample was analyzed for ash, moisture, and size consist; another sample was sent to the Iowa state University for trivial shear tests (supplying an index measurement). Actual flowability results from the bin were then compared to the measured index to determine the applicability of the handleability index in actually predicting coal flow problems. This paper describes the correlation between handleability index and bin flow and explains the next stages of the project.

Jan 1, 1992

By W. C. Taylor

The present fuel situation indicates that, at least for the next 20 to 30 years, the burning of coal will be a main source of energy. All coal contains sulfur, which is converted to sulfur dioxide during combustion. The concentration of sulfur dioxide (SO2) in the resulting flue gas, for most coals, would exceed the limits established by the Environmental Protection Agency (EPA). Therefore, the sulfur must either be removed from the coal prior to its burning, or be collected from the stack gas before it reaches the atmosphere. There is currently a large amount of research devoted to methods of removing the sulfur from the coal before burning, or during combustion in fluidized beds with materials which trap the sulfur in the solid residue. The commercialization of these processes, however, is not expected in the near future. Flue gas desulfurization appears to be the best near term prospect of fulfilling current air quality control regulations. The lime/limestone wet-scrubbing methods are the most advanced flue gas desulfurization processes and will account for the majority of sulfur removal systems in electric power generation. There are currently at least 23 full-scale systems existing or under construction and 17 of these will use the lime or limestone wet-scrubbing process. (1)

Jan 1, 1974

By J. T. Clancey

The potential inadequacy of natural gas reserves to supply projected requirements in the 1980's has been pointed out.(1,2) As a result, interest has arisen in the development of new, potentially low-cost processes for the conversion of coal into high BTU gas. In June, 1964, the office of Coal Research (U. S. Department of interior) and Consolidation Coal Company (now a subsidiary of Continental Oil Company) entered into a contract to continue work on coal gasification utilizing the Consol CO2 Acceptor Process. Work under this contract has been specifically directed toward the use of lignite as the carbonaceous feed, although the process is also applicable to non-caking subbituminous coals. The primary objective of this work was to establish the technical feasibility in continuous bench-scale equipment, of the novel features of the C02 Acceptor Process. Secondary objectives were the testing of commercially obtainable acceptors and the design and economic evaluation of a commercial facility. The bench-scale process development has been completed successfully and the construction of a large pilot plant at Rapid City, South Dakota, has been authorized. It is the purpose of this paper to review the technology of this new gasification process and to present the current projected economics of a plant producing 250 MM SCFD of pipeline quality gas.

Jan 1, 1969

By K. Kim

A site characterization strategy formulated for the probabilistic design of underground structures is presented, which takes into account the variability of rock properties and the stochastic nature of the rock failure process. It entails determining probability distributions of rock properties by utilizing the theory of extremes and Monte Carlo simulation. Laboratory and field test data are analyzed and presented to illustrate the methodology. The results indicate that the distributive characteristics of rock mass properties can be estimated using empirical relationships currently available. This results of analyses can be incorporated into the design of underground structures, and then, the relative uncertainties of the failure probability of the structures can be assessed.

Jan 1, 1995

By Yongjun Peng, Yufan Mu

Pyrite depression in the flotation of copper ores is difficult due to the activation of Cu2+ ions on pyrite surface. In this study, the radical chain reaction involving the redox cycling of Cu(I/II) induced by sodium metabisulphite (MBS) was exploited to selectively depress the flotation of copper-activated pyrite at pH 8.0. Electrochemical measurements revealed that the presence of Cu2+ and O2 was essential to the formation of SO•− 5 through sulphite oxidation, the main entity to convert the activating species Cu(I)S on pyrite to Cu(II)-hydroxide/sulphate, causing deactivation of pyrite. The depression role ofMBS on pyrite flotation was closely associated with the type of grinding media which affected the electrochemical conditions of flotation. When forged steel was used as the grinding media, a high dosage of MBS was required to depress pyrite, but a low dosage of MBS could almost completely depressed pyrite when high chrome steel grinding media was used. This is because high chrome steel produced a stronger oxidation condition with a higher amount of Cu2+ and O2 which promoted the formation of SO•− 5

Jan 26, 2021

By John A. Cherry

Groundwater monitoring conducted at an acidic uranium-tailings impoundment in Wyoming and at one in Ontario indicate that at these unlined impoundments situated on unconfined sand aquifers, there exist well-developed plumes of contaminated groundwater. In the literature similar results are reported for three other unconfined aquifers at mill sites in Wyoming. The plumes extend for distances of several hundred to a few thousand metres from the impoundments. They have a zone of low pH beneath and adjacent to the impoundments and a larger zone of near-neutral pH that extends to the outer limits of the plume. The low-pH zones are generally small compared to the neutral-pH zones because the advance rate of the fronts of acidic tailings-derived water is slower than the average velocity of groundwater which controls the advance of the high pH zone. The retardation of the acid fronts is a result of geochemical reactions that cause hydrogen-ion consumption in a slowly-advancing neutralization zone. Within each of the plumes, the low-pH zone has high concentrations of transition metals, heavy metals and radionuclides. In the neutral-pH zones all of the metals and radionuclides occur at significantly lower concentrations and are generally at levels much below those specified in national drinking water standards. An exception at two of the Wyoming sites is uranium, which exists at levels close to the drinking water limit. A second exception is ferrous iron at the Ontario site, which occurs at high concentrations throughout most of the plume. The carbonate alkalinity at this site is much lower than at the Wyoming sites. The field data indicate that even in very permeable aquifers with a low content of silt and clay, there is normally a considerable capacity for acid-front retardation. To take advantage of this capacity to control contaminant movement in the design, operation and decommissioning of tailings impoundments, it is necessary to be able to predict the rate of acid-front movement. This predictive task has two primary components. The first is to identify the important flow paths from the tailings through the groundwater system and the second is to determine the degree of acid-front retardation that will occur as the tailings-derived water moves along these flow paths. Relative to these two tasks determination of the effects of hydrodynamic dispersion is generally of lesser importance and simple approximations that do not involve field or laboratory tests are probably adequate. In order to effectively apply the acid neutralization concept to the prediction of subsurface contaminant migration at uranium-mill tailings, improved representations of hydrogeochemical behavior of iron and aluminum in the neutralization zone and of the consumption of hydrogen ions through reactions with carbonate and aluminum-silicate minerals are required. Along with the hydrogen ions contained in the tailings water the ferrous iron represents a large potential source of acid but the extent to which ferrous iron converts to ferric iron to produce acid is problematic. Detailed hydrogeochemical evaluation of existing contaminant plumes and the performance of laboratory experiments under appropriate redox conditions ore prerequisites for the improvement of predictive models. However, the existing field and laboratory data provide a basis for preliminary predictions of contaminant migration from acidic uranium tailings impoundments.

Jan 1, 1982

By Lake H. E.

The request to participate on your theme panel was accepted with some reluctance but indeed as an honor. My subject was outlined to cover 'Energy Resources - both nuclear and conventional' as related to your theme 'Minerals - Treasure Trove of the West'. This is indeed quite an order and I hope you will forgive me for concentrating mainly on the nuclear-uranium portion with brief references only to conventional fuels some of which will be covered in detail later in your conference. In regard to Uranium, I am speaking on the fringe of the area containing half the uranium reserves in your country and no doubt to many who are very conversant with knowledge of these resources. Nevertheless since our two countries have been very closely allied in both nuclear developments and uranium supplies I hope an exchange of information may be mutually beneficial. Concentration on the nuclear fuel resources is I hope understandable as nuclear energy is the coming source of power which will augment the rapid demand in the industrialized countries and provides hope for economic power in many of the more underdeveloped countries. The situation regarding conventional fuel resources is more widely known and their expanding future revolves around production cost reductions, research into diversified uses, plus more assurance of imports from countries less effected by international controversies determining export policies.

Jan 1, 1967

By Betty Gibbs

The Ore Body Modeling and Mine Planning Worshop, sponsored by the Society for Mining, Metallurgy, and Exploration, Inc. (SME), was held Feb. 22-24, 1991 before the SME Annual Meeting and Exhibit in Denver, CO. More than 40 people from mining companies, government agencies and universities attended. Eight vendors of integrated ore body modeling and mine planning software attended and presented the results of problem sets given before and during the workshop. They were: [ ]

Jan 1, 1991

By K. C. Liddell

Chemical processing research made notable advances during 1986. This overview is necessarily brief. It is intended, though, to give the flavor of selected areas where recent activity has been high. At the 1986 Annual Meeting of The Metallurgical Society, a symposium was held on hydrometallurgical reactor design and kinetics. R. G. Bautista, R. J. Wesely, and G. W. Warren edited the resultant proceedings volume. This is the first available volume on this subject. It includes 26 papers on fundamental kinetic studies, modeling of reaction kinetics and reactor performance, and pilot and production-scale operations. Metals discussed include silver, gold, platinum, titanium, cobalt, nickel, zinc, copper, manganese, and iron. Agitated tanks, heaps, dumps, pachucas, pressure auto-claves, electrolytic reactors, liquid membranes, and fluidized beds are among the reactor types covered. An international symposium dealt with iron control in hydrometallurgy. It was sponsored by the Metallurgical Society of CIM, the Institution of Mining and Metallurgy, The Metallurgical Society of AIME, and Gesellschaft Deutscher Metallhutten and Bergleute. J. E. Dutrizac and A. J. Monhemius edited a proceedings volume containing 41 papers. These covered many areas of process chemistry, solvent extraction, precipitation, treatment of pickle liquors, impurities, residues and the environment, and process selection. Precious metals Concerning precious metals processing, the US Bureau of Mines IC 9059 is noteworthy. It includes papers presented at a USBM briefing at the Western Mining Conference in Denver. Topics covered included ion exchange, staged heap-leaching direct-electrowinning, and mercury precipitation during cyanide leaching of gold ores. Also dealt with were carbonaceous gold ores, carbon adsorption and desorption, heap leaching, the carbon-in-pulp process, and precious metals recovery from electronic scrap and solder. R. C. Sandberg and J. L. Huiatt (Journal of Metals, June 1986, and USBM RI 9022) developed a method to recover silver, gold, and lead from a complex sulfide using ferric chloride, thiourea, and brine-leach solutions. Gallium Gallium recovery was also a subject of considerable interest. Much information on this topic is proprietary. But two papers described solvent extraction of gallium. V. P. Judin and R. G. Bautista (Metallurgical Transactions B, 1986) developed an equilibrium model to separate gallium chloride from aluminum chloride. Tributyl phosphate was the extractant studied. T. Sato and H. Oishi (Hydrometallurgy, 16, 1986) investigated gallium extraction from sodium hydroxide by using Kelex 100. Data were given on the equilibrium distribution and the extraction kinetics. Galena Interest continues in recovering lead by hydrometallurgical processing of galena. J. E. Dutrizac; S. H. Kim, H. Henein, and G. W. Warren; and M. C. Fuerstenau et al. (Metallurgical Transactions B, 1986) all investigated leaching of PbS by ferric chloride. Dutrizac reported parabolic kinetics and reaction control by outward diffusion of lead through a porous layer of elemental sulfur. Kim, Henein, and Warren, however, reported that two leaching reactions occur. A nonoxidative reaction produces H2S and there is an oxidative leaching by ferric ion. Acid dissolution was found to predominate when the acid activity to ferric activity ratio is high. Surface chemical reaction was reported to be controlling. Fuerstenau et al. also reported that mass transfer through the sulfur layer is rate determining. But they believe that the species transferred are chloro complexes of ferric ion. In other work on lead, A. Y. Lee, A. M. Wethington, and E. R. Cole, Jr. of the USBM described an environmentally acceptable hydrometallurgical alternative to the smelting of lead concentrates (RI 9055). Uranium In spite of depressed prices, much work has been reported on uranium processing. R. G. L. McCready, D. Wadden, and A. March-bank (Hydrometallurgy 17, 1986) described the nutrient needs for in-place leaching by T. ferrooxidans. They reported the optimal conditions for uranium solubilization. L. E. Eary, H. L. Barnes, and L. M. Cathles (Metallurgical Transactions B, 1986) carried out an experimental and modeling study of uraninite dissolution. They concluded that ferric ion preferentially leaches uraninite in pyritic ores. Hydrogen peroxide was found to be less selective. A. Vuorinen, P. Hiltunen, and O. H. Tuovinen (Hydrometallurgy 15, 1986) studied redox and precipitation reactions of iron and uranium in leach liquors. P. T. Chiang (Hydrometallurgy 17, 1986) reported on the effect of uranium loading in the DEPA-TOPO process to separate uranium and iron from wet-process phosphoric acid. F. J. Hurst (Hydrometallurgy 16, 1986) conducted a fundamental study of the separation of uranium from phosphoric acid by DEPA and TOPO. D. E. Chia and W. C. Cooper (Hydrometallurgy 16, 1986) reported on bench and pilot scale work to recover uranium by the HIMIX process. They reported that the acid consumption to produce an eluate suitable for yellowcake

Jan 5, 1987

By Edward DeLilla

For the past 30 years, surface mines have moved toward more highly mechanized, automatic systems that continuously mine overburden and ore to increase productivity, lower operating costs and minimize manpower needs. To achieve these goals, mine operators must be involved in every step of the machine procurement process. Several factors are involved in making the machines operate economically and efficiently: -Prudent engineering. -Proper planning. -Realistic feasibility studies. -Effective specification. -Thorough training of the mine personnel.

Jan 1, 1994

By Francesco Chiappalone, Marco Invernizzi, Franco Gasperin, Brad Yoder, Fabrizio Fara

The Ship Canal Water Quality Project includes a 2.7-mile, 18-ft and 10-in internal-diameter tunnel that extends from Ballard to Wallingford, two popular neighborhoods in the West of Seattle. During the TBM Main drive a 12' × 12' boulder with variable strength up to 47,000psi was encountered resulting on signicant damages to the Cutter ead. The rst part of this paper describes the design and construction of an underground recess in front of the TBM to create a safe working environment for the TBM repairs. The second part describes an injection campaign performed to seal an unforeseen water inow appeared during the excavation of the 11 Avenue Diversion Structure.

Jun 23, 2024

Current scrubber capacities vary from 1.89 to 4.72 m3/s (4,000 to 10,000 cfm), and there is interest in using scrubbers with capacities up to 6.61 m3/s (14,000 cfm). This paper describes research to compare the effectiveness of blowing and exhausting face ventilation systems using high-capacity scrubbers with flows up to 6.61 m3/s. Tests were conducted in a surface ventilation gallery with exhaust and blowing systems operating under similar conditions. The mining machine was equipped with a machine-mounted scrubber. Methane gas was released at constant flow at the mining face and measured at several face locations. Effectiveness of exhausting and blowing systems was compared by determining average face methane concentrations. For each operating condition tested, blowing ventilation was more effective than exhausting for controlling face methane levels. Raising scrubber flow to 6.61 m3/s reduced methane levels for both blowing and exhausting systems.

Jan 1, 1996

By Edwin W. Tooker

Creation of needed new resources will be accomplished mainly by imaginative and diligent geologic exploration because geologic availability is the key determinant of future mineral supply. Adequate resources of most commodities can be made available for the rest of this century and beyond if they are discovered. Thus conversion of hypothetical and speculative resources into available reserves will provide the principal challenge to earth scientists. Additional problems now compete for our attention. First is a challenge to discover more resources than have been found to date for domestic needs as world-wide demands increase exponentially and as easily found high-grade deposits are rapidly being depleted. New ways to find new types of deposits are required. Second, the United States, a resource importer, increasingly is challenged for access to foreign supplies through stiffening competition and economic or expropriation sanctions. Balancing needs for mineral supply and environmental protection is a third challenge. Geologic explorers must consider statutory as well as economic and technologic requirements, controlled access to public and private lands, competition with urban sprawl or wilderness, limitations on discovery, appraisal and mining methods, and restoration of mined areas. Finally, is the challenge to temper public and private attitudes and assure that decisions bearing on resource problems are based on comprehensive credible facts. While striving to maintain and improve the standard of living, many Americans appear to disdain and mistrust those organizations that provide their material where-withal. Meeting these challenges effectively, and in time, will require careful appraisal of the resource system and the joint efforts of industry, university, and government earth science research.

Jan 1, 1974