Search Documents

By William M. Gleason

Hard times continued to plague the industry when the calendar rolled over to 2000. During 1999, the United States economy had grown vigorously, capping the longest economic expansion in United States history. However, the mining industry was not so fortunate. Commodity prices remained in a slump in the “new-economy” that was fueled by excitement and speculation about the power of the Internet during the infancy of the Information Age. Much of the investment money that once went to mining and exploration was now headed to the world of virtual gold mines. SME President Donald E. Ranta implemented new technology into his plans for SME. His two major goals were new membership growth and to foster the establishment of the comprehensive Internet presence for the Society’s technical information. His strategic priorities included enhancing the quality and quantity of publications, programs, meetings and short courses. “The Internet is the vehicle that will advance the priorities,” he said.

Jan 1, 2007

By K. L. Lownie

For research and test data to serve a useful purpose, it is essential that it be derived from some known standard test procedure that allows for comparative analysis as well as independent replication and verification. Fan performance data provided by manufacturers is not absolute, and is influenced by the geometry of the test installation. For these reasons, fan test standards have been prepared in order to establish a clearly defined test procedure that allows for comparison of different fan designs, and also allows for the independent verification of test data. Internationally recognized Standards such as BS848, ISO5801, and AMCA 210 etc. are highly prescriptive, and precisely specify test duct configurations, measurement procedures, measurement planes and instrumentation to be used. Provided the laboratory tests are conducted strictly in accordance with the relevant Standard, the performance data will accurately reflect fan performance within the appropriate tolerances for efficiency, pressure and flow when tested in the defined configuration. Major differences in performance exist between a fan tested in accordance with a Fan Test Standard, and an identical fan installed in a mine ventilation system. The aerodynamic performance of any fan will be influenced by the quality of the fan manufacture, the flow system within which it is operating, the location of measurement planes, and the system stability. The flow distributions present in a standardized Laboratory test are unlikely to be repeated in mine ventilation systems, and this will also disadvantage fan performance. Unless the fan supplier takes all of these influences into account, there will an inevitable reduction in fan aerodynamic performance, and the end user will experience a shortfall in expected flow through the mine. The effect on fan performance can range from minor inconvenience to catastrophic fan failure resulting in major rectification costs and significant loss of mine production.

Jan 1, 2009

By William H. Lane

After a number of years of engineering and operating assignments and through many types of evaluations, the need for a simple analytical method of evaluating mine haulage alternatives became obvious. Haulage, like 50 many other facets of mining, is generally a sequence of interconnected events that change, often drastically from mine to mine. Often the operator or the mine engineer has neither the time, manpower, facilities, or information needed to prepare a detailed evaluation. For many studies or for routine variance analysis, that detail may not be necessary. The intent of this article is to present an approach for analyzing mobile mine haulage that is simple and straight-forward. These methods are not designed to replace more formal and detailed procedures that have been developed previously and are available in our technical libraries. They are offered as a tool to be applied to preliminary designs, feasibility studies, and variance analyses where more complete detail is not warranted. These methods will eliminate combinations that are not economical or appropriate before more intensive and complete evaluations are undertaken. These methods may also be used to evaluate ongoing operations and to plan changes in those operations. This presentation describes a series of steps that have evolved for the handling of haulage evaluations. It concentrates on the factors having major impact on the results. Because the approach is a sequence of distinct steps, a case study was chosen as the best method of presentation. This case is a composite of several actual situations that have been encountered within the last few years.

Jan 1, 1978

Collaboration between education providers is the key to long-term sustainability and improved quality in mining education. The mining industry is now, more than ever, an industry doing business on a global basis. Staff are recruited by global mining companies in many different countries and can find themselves deployed anywhere in the world. The mining engineer of tomorrow must be willing to take on this international challenge, and must be educated to a level where he or she has a comprehensive grounding in technical aspects of mining engineering, but also a well-founded appreciation of management, social, environmental and cultural issues that may be encountered around the world. In order to deliver such an education, academic providers must collaborate at both a national and international level. This paper provides an overview of progress that has been made in Australia through the national joint venture ? Min¬ing Education Australia (MEA). Supported by the mining industry in Australia, through the Minerals Council of Australia (MCA), MEA has been operational since 2007 and is seeing the development of a range of innovative courses and delivery methods, together with a high level of staff cooperation across the country. MEA has also commenced some international teaching initiatives that are seen as a catalyst for a far greater degree of international collaboration in the future. Such activity is not only to the benefit of the students who are taught by experts from around the world, but it also ensures that individual univer¬sity programs remain viable in terms of staffing numbers and financial performance. The paper also presents some statistics on recent upward trends in mining engineering student numbers from around the world, in response to the global shortage of mining engineers.

Jan 2, 2010

By Jack Magtoto, Lysa Voight, Tom Martin, John Forero

SUMMARY Commitment by all parties to partnering goals established early in the contract aided Affholder, Inc. in constructing 2,360m (7,700') of soft ground tunnel in Rancho Cordova, CA. Despite two zones of known contamination, encountering a zone of loose cobbles and boulders in a matrix of flowing sand, some perched water tables and a flooded tunnel after 2 upstream safety plugs failed, the Contractor finished the work 33 days early and only 1.91% over his original bid.

Jan 1, 2007

By William Gleason

Despite a global slowdown in most mining sectors, Caterpillar, the world?s largest mining equipment maker continues to forge ahead with new, and improved offerings to the global mining industry. On Nov. 10, as part of its Loading and Hauling Mining Focus Session at its Tinaja Hills proving grounds south of Tucson, AZ, Caterpillar unveiled to customers and media its two latest mining products, the 994K wheel loader and 6020B hydraulic shovel. The Caterpillar 994K wheel loader builds on a nearly 25-year history of the 994 model but with one noticeable difference ? the 994K is bigger ? much bigger. Weighing in at 239,142 kg (527,218 lb) the 994 K is up to 20 percent larger and comes with up to 30 percent increase in payload capacity. This behemoth of a machine is currently being tested at Caterpillar?s Tucson Proving Grounds, Anglo Gold Ashanti?s Cripple Creek and Victor gold mine in Colorado and Taseko?s Gibraltor copper and molybdenum mine in British Columbia, Canada.

By Eugie Kabwe

Rock bolts are components of tunnel support structures and their efficacy in reinforcement requires the appropriate estimation of the bolt pre-tension. However, cases of ineffective rock bolt application due to loosening are common which leads to the potential failure of the support structures, thus negatively affecting the tunnel stability. The effective employment of pre-tensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut pre-load. Henceforth, this paper presents a load indicator washer (LIW) capable of withstanding assigned static loading as well as provides an appropriate pre-tension. The different LIW breadths are numerically analysed in the finite element code (ABAQUS) to estimate deformation when a designated 60-kN pre-load is applied. The numerical simulation employs a bi-linear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nutLIW-rock bolt connection. Therefore, a long-term relaxation effect on bolt pre-tension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW-predetermined deformation is the bolt pre-tension. It is drawn from the simulation results that the 1.5-, 2.0-, 3.0-, 3.5-, and 4.0-mm-thick LIWs are completely flattened when subjected to 28-, 42.5-, 65-, 76-, and 88-kN pre-load respectively.

By Jr. Smith

Borates have been mined in the desert areas of California and Nevada for more than 100 years. To about 1890, playa surface mining provided the chief sources of boron minerals. Underground mining of colemanite and later of borax and kernite was predominate until about twenty years ago. Open pit mining of the large deposits of borax and kernite near Boron, California has been most significant for the past twenty years. Mining of colemanite in the Ryan, California area, near Death Valley, began in 1907. Following the discovery of the large deposits in the Boron area (about 1957), mining in the Death Valley area became nearly nonexistent. Only small tonnages were mined for special uses. Little mining was done in the Boraxo area near Ryan. The first claim was made in about 1915 In 1960 the area became the property of the Kern County Land Company, which was acquired by Tenneco Oil Company in 1967. In 1976 the various borate properties and claims in this region were acquired by American Borate Corporation. The open pit mine is now approximately 400 feet (121.9 m) deep, 3000 feet (914.4 m) long and 1000 feet (304.8 m) wide. The borates in the Boraxo pit consist primarily of three minerals. These are about 50% coiemanite (C2B6O11' 5H2O), about 40% probertite (NaCaB5O9.5H2O), and 10% ulexite (NaCaBcO9.8H2O). The colemanite, along with boric acid and high-grade coiemanite ore from Turkey provide the only sodium-free borates for production of textile grade fiberglas. When heated to its decomposition temperature, colemanite decrepitates to a fine powder. This provides the basis for the concentration process. The gangue minerals in this deposit are primarily calcite and clays, including bentonite. The ore body has a very low arsenic content.which is a desirable feature. Test work had been done with samples prior to the results discussed herein. This paper will discuss results of test work which were the basis for erection of a plant, and the subsequent plant operations.

Jan 1, 1978

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

By A. Fred Gelding

Introduction In preparing this paper considerable time was spent attempting to find some upbeat data about the mining industry, so those of us in the field could feel somewhat better about future prospects. Much to my regret, I failed to uncover substantial evidence that our near-term or, for that matter, our long-term opportunities appear all that bright in North America. That is certainly not the kind of assessment anyone likes to hear or accept as even a possibility. Those remarks may, on the surface, appear far too pessimistic. This industry will experience a recovery and most likely will see conditions begin to improve later this year or early next. The kind and degree of recovery, however, will more than likely differ from those experienced in the past. Fundamental Changes Clearly, the fundamentals on a world scale of our business have undergone important changes. In recognizing these fundamental changes, mining authorities believe productivity advances are needed to change the direction mining has taken in recent years. The really tough question is whether increases in productivity will be enough to change the course of events that has dominated the mining sector for the past decade. Before one can provide an honest answer, an appraisal of what has and is happening now is necessary. Here are some changes and events that have taken place that effect domestic mining and will probably continue: • Mineral-rich lesser developed countries (LDCs) in Africa, South America, and Asia-Pacific have reached a point where they have developed the needed mining infrastructure to not only produce at a high rate, but in many instances, at a lower cost than fully developed countries. Just as importantly, these countries, even if they do not enjoy lower costs, will produce for world export with government subsidies because min¬ing products are key in obtaining badly needed foreign exchange. • These producing countries also have the distance advantage of lower labor, environmental, and other important regulatory costs. If that were not enough, these same countries have minerals with considerably higher grade ore and, in some cases, much lower cost accessibility. • Exporting North American commodities is impaired by a dollar that continues to strengthen against other important currencies around the world. There are other impediments to overcome, but these represent some of the realities our industry faces. Can those obstacles be overcome through improving productivity? In the past, this industry has offset the impact of these events to a sizeable degree through innovations of mining techniques, equipment and processes, and by increasing the size of its individual operations to reduce costs. Will further enhancements along these lines be enough to alter this changing balance in the future? While there is no answer, it is apparent that if we do not mount a full-scale assault in some key areas, our prospects will not be encouraging. Productivity improvements throughout the entire chain of the mining industry most certainly rates as a high priority. Every link in that chain from mine planning, equipment selections, and transportation considerations needs to be examined and reexamined to assure the lowest effective cost is developed. Quality, while oftentimes costing a little more initially, is still the most cost effective purchasing decision to make. Regulations Another area of concern is regulations, be they environmental or those that dictate what must or must not be done in running our business. Certainly, I do not suggest that we not protect our environment. However, there is an acceptable balance that has, over

Jan 11, 1983

By Ray L. Tobie, Douglas E. Julin

GENERAL DESCRIPTION Block caving is a distinct caving method applied mostly to large, massive, ore bodies because of its in¬herent low cost and high production capabilities. Areas of sufficient size are removed by undercutting so that the mass above will cave naturally. Drawing of the caved ore at the bottom of the ore column causes the caving action to continue upward until all of the ore above the undercut level is broken into sizes suitable for handling. When properly applied, block caving results in a lower mining cost per ton than any other under¬ground method. There are three distinct forms: (1) dividing the horizontal area into rectangular or preferably square or nearly square blocks, drawing evenly over the entire area to maintain an approximately horizontal plane of con¬tact between broken ore and caved capping; (2) divid¬ing the horizontal area into panels across the ore body, retreating by undercutting manageable areas from one end of the panel to the other and maintaining an in¬clined plane of contact between the broken ore and caved capping (thus the name panel caving); and (3) no division of horizontal area of the ore body into defi¬nite blocks or panels (this is termed mass caving). Undercutting may be from wall to wall, retreating from one end of the ore body to the other, maintaining an inclined plane of contact between the broken ore and caved capping. The total active caved area is deter¬mined by the size of block that will not produce undue stress on workings below the undercutting level and by total production requirements. This type of operation is also referred to as panel caving at some properties. SUITABLE ORE BODIES Block caving in its various forms is applicable to deposits of various shapes and ores of various strengths. Its success is governed by rigid requirements and limi¬tations. In unsuitable deposits or where improperly em¬ployed, the loss of ore may exceed that of any other mining method. Good planning, systematic work pro¬cedures, careful supervision, and good judgment con¬tribute to its success. Ore Characteristics Included as a necessary characteristic in an ore body suited to a successful block-caving operation is a proper fracture pattern. Ore hardness should be another gov¬erning factor, and the toughness or softness of the ore should be considered. There must be sufficient horizon¬tal area available for expansion of the undercut, if neces¬sary, to start the caving process. Large, massive, ore bodies usually meet these conditions. Veinlike deposits must be wide and dip rather steeply to conform to the block-caving limitations. The capping must be of such a nature as to cave when the underlying ore is being removed since the weight of the overburden aids in crushing the ore. The most favorable capping character¬istic is that it breaks into coarse pieces and resists attrition as the block is drawn. Soft capping, by breaking into fine pieces and sifting into the ore or channeling through the ore to the drawpoints, can seriously dilute the ore and hinder the extraction of clean ore from the blocks. Types of Ore In block caving, a fairly uniform distribution of val¬ues in the ore is necessary. Grade values may range from low grade to high grade, but most often the sys¬tem is applied to low-grade ores. Wide veins, thick beds, or massive deposits of homogeneous ore overlain by ground which will cave constitute suitable ore bodies. The ore must be such that it can be supported while blocks are being developed and undercut but breaks up readily when caved. Some applications include porphyry copper, disseminated molybdenite, hematite in the Lake Superior iron district, limonite deposits in northern Spain, the diamond mines of South Africa, asbestos and nickel in Canada, and massive magnetite in Pennsylvania. Size and Shape Outline of the ore body should be fairly regular, and the sides of the ore body should dip steeply. It may not be economical to mine small portions of ore extending into the walls of the deposit, and low-grade inclusions in the ore cannot be left unmined. Some dilution of the ore, as mining progresses, by low-grade or barren cap¬ping is inevitable and, unavoidably, some clean ore is left between drawpoints. Determining Cavability The use of rock mechanics is sometimes advantageous in helping to determine the cavability of an ore deposit. The US Bureau of Mines has information and testing ability which can assist in determining the cavability of ore types. Several competent consulting orga¬nizations knowledgeable in rock mechanics can also as¬sist in evaluating the cavability of an ore body. Some recent work has been done to better define the cavability index of various ore bodies; an example of how this was determined is discussed by McMahon and Kendrick (1969). The intensity of the fracture pattern is a critical parameter to be analyzed. The question to be answered is, "How intense must the fracture pattern be?" Table 1 is a tabulation of the size of rock fragments that appear at the drawpoint of various block-cave mines around the world. These are indicative of the fracture-pattern spac¬ing and, as can be seen, they vary substantially from the almost sandy material at the Mather mine to fairly sizable blocks at the Grace mine. Several sets of fractures are essential to promote good caving. Ideally, two vertical sets at nearly right angles to each other and a third set nearly horizontal are required to insure a good caving ore body. Since initial caving of an ore mass is almost always by the action of gravity acting on these planes of weakness, it is doubtful

Jan 1, 1982

By Jordi Vives-Costa, J. J. de Felipe, Lluís Sanmiquel, Maria Niubó

The article evaluates the convective heat transfer coefficient of ventilation air in a potash mine. The energy balance is obtained through thermal characterization of the ventilation air and rock, allowing for the calculation of heat transfer parameters. Different models for calculating the convective heat transfer coefficient are analyzed. The results indicate that the Pethukov–Kirilov, Gnielinski, and modified Dittus–Boelter models are optimal for this mine. The study also indirectly examines the conductivity of the adjacent rock, suggesting saturation throughout the studied section and the presence of liquid water upwelling in a specific section.

Apr 7, 2022

By Ihor Kunasz

The high lithium demand forecasted for some high tech applications and batteries for electric and hybrid-electric vehicles, in particular, has sparked increased exploration for lithium, particularly for lithium- and potassium-bearing brine deposits. The latter have generally followed the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) NI 43-101 guidelines on resource reporting, formulated for hard rock deposits (metals and industrial minerals). While a number of the requirements can be appropriately applied to brines, brines are fluids and require a specific analysis leading to a distinct set of reporting requirements. Brines cannot be considered industrial minerals because the various elements occur as ions in a dynamic fluid, rather than being chemically bonded in a solid. Although chemicals are produced from brines, brines have no relation to industrial mineral deposits. This article analyzes the recently released (Nov. 1, 2012) document CIM Best Practice Guidelines for Resource and Reserve Estimation for Lithium Brines, in light of the practical knowledge available from existing brine operations. It recommends modifications to the guidelines, which, if applied in their present format, will result in overstating resources and reserves and mislead potential investors. The CIM Best Practice Guidelines for Resource and Reserve Estimation for Lithium Brines document is generally descriptive and does not fully address the methodology for brine resource or reserve definition. Lithium and other elements (potassium, magnesium) are contained in a fluid, the hydrologic characterization of which should be the principal focus of a brine exploration program. The fundamental requirement in defining lithium brine resources and reserves in a salar is the identification and definition of those formations ? the aquifers ? that will yield brine in a usable quantity to a well, because brines can only be extracted by pumping wells. Fine-grained sediments will never, as required in the summary Table 1, have ?reasonable prospects of economic extraction,? cannot be considered and, therefore, need not be tested. However, the guidelines recommend the collection of solid samples and a high-core recovery for laboratory testing of various sediments instead of focusing on the brine.

Oct 1, 2013

By Marcos de Paiva Bueno, Leonardo Ribeiro Lara, Rajiv Chandramohan, Thiago de Almeida, Greg Lane

This paper explores the impact of the significant difference between the number of geochemical assays conducted for grade estimation and the number of comminution tests performed for throughput and performance forecasting. Both grade and throughput are key factors in determining the project. We analysed 154 feasibility study reports to assess the impact of sample frequency for comminution test work on project revenue. This disparity in size between assay and comminution data arises because geological and resource-grade risks cannot be managed without extensive geochemical testing, whereas comminution risks are traditionally mitigated through design methods and the use of contingencies. This approach is partly due to the relatively high cost and large sample requirements associated with traditional comminution tests. Our analysis demonstrates that insufficient comminution sampling and testing leads to uncertainties in throughput forecasts, creating significant financial risks. Data from the feasibility studies show that a 1% change in mill throughput can result in up to a 5% variation in Net Present Value (NPV), underscoring the sensitivity of project economics to operational performance. Building on previous work, we reference studies that reveal how low frequency of comminution testing can increase uncertainty in mill throughput forecasts and increase financial risks. We propose an approach that optimises the number of comminution samples tested to enhance forecast accuracy and reduce NPV variance. By adopting this approach, mining projects can improve financial reliability and mitigate risks associated with underperformance in SAG and AG mill-based operations.

Feb 1, 2025

By Kentaro Kuraji

INTRODUCTION Background Tokyo, the capital of Japan, is one of the largest cities of the world. As many as 33 million people live in Tokyo and three neighboring prefectures although the city occupies only 0.6% of the area of the country. The network of Metropolitan Expressways serves as a major artery for daily physical distribution in Tokyo. The Central Circular Route of the Metropolitan Expressway (MECCR) is located innermost among the three circular routes in Tokyo (Figure 1). Once completed, MECCR is expected to drastically mitigate traffic congestion in the central Tokyo area and provide drivers wider varieties of options in route selection. Alleviating congestion is estimated to reduce 400,000 tons of carbon dioxide emissions annually. The eastern and northern sections and part of the western section of MECCR have been completed with the total length reaching 33 km. The western section will be extended southward by approximately 4 km in the spring of 2010. An 11-km-long western section of MECCR that is currently being constructed is composed mostly of tunnels. A large number of power supply, gas supply, telephone, drinking water and sewerage pipes have been placed under the Yamatedori avenue along which MECCR is being constructed. The shield tunneling method has therefore been adopted for constructing tunnels along the route. The method involves the advancement of a shield tunnel boring machine (TBM) through the ground simultaneously assembling segmental rings within the shield. The method not only enables the building of highway tunnels more quickly and efficiently than other methods but also minimizes the effects of construction work on the surrounding area and the environment. Constructing the tunnel using the conventional cut-and-cover method might have required large amounts of time and cost because relocating the numerous objects buried under the Yamatedori avenue might have been necessary during tunnel construction. It was also considered desirable to place the tunnel at a depth of 30 m or more from surface to prevent tunnel construction from adversely affecting railways because the tunnel was expected to cross eleven railways and subways. This is one of the reasons for selecting shield tunneling as an effective method. The shield tunneling method was finally adopted for a length of 7 km in the 11-km western section of MECCR. The shield tunneling method was also employed in the Ohashi Tunnel located southernmost in the 11-km western section of MECCR. This paper describes the construction of the Ohashi Shield Tunnel.

By Thomas G. Goonan

Copper production through smelting generates large volumes of material flows. As copper contained in ore becomes copper contained in concentrate to be fed into the smelting process, it leaves behind an altered landscape, sometimes mine waste, and always mill tailings. Copper concentrate, fluxing materials, fuels, oxygen, recyclables, scrap and water are in-puts to the process. Dust (recycled),gases — containing carbon dioxide(CO2) (dissipated) and sulfur dioxide (SO2) (mostly collected, transformed and sold) and slag (discarded or sold) — are among the significant process outputs. This article reports estimates of the flows of these input/output materials for a particular set of smelters studied in some countries. They include Chile (Altonorte, Caletones, Chagres, Chuquicamata, LasVentanas and Potrerillos), Japan(Naoshima, Onahama, Saganoseki,Tamano and Toyo), the United States(Garfield — Fig. 1 — Miami and Hayden) and Europe (Glogow I, Glogow II, Huelva, Norddeutscheand Ronnskar).

Jan 1, 2005

By ?. ?ivkovic

The silicate slag and copper matte that are the byproducts of smelting copper in a reverberatory furnace contain SiO2, FeO, Fe3O4, CaO and Al2O3, and Cu, Fe and S, respectively. These components influence the oxide (Cuox), sulfide (Cusul) and total (Cutotal) copper content lost in the waste slag. This paper uses multiple linear regression analysis (MLRA) to determine the degree of influence. The results of calculations obtained using MLRA were compared to actual measured results and found to have a large degree of correspondence, with the coefficient of determination R2 = 0.975. These results indicate that slag composition and copper content in the matte influence the copper losses in the waste slag with a probability of above 97%. It was determined that, of the total copper content of the slag, 74% is in sulfide and 26% in oxide form, and that this ratio is not dependent on the slag or matte composition.

Jan 1, 2010

By H. Hejny

"The mine of the future will exploit mineral raw materials at greater depths than today, requiring completely different approaches compared to today’s deep mines, in order to get mineral rights. Only these eco-efficient mines will contribute to improved access to domestic mineral resources, secure the sustainable supply of mineral raw materials for Europe and reduce the import dependency. IntelliMine will contribute to realise these concepts of invisible, zero-impact and safe mines. The mine of tomorrow will run an integrated concept in order to guarantee the desired level of sustainability. All operations necessary for the eco-efficient provision of the minerals including waste management will be carried out underground. This will drastically reduce the volumes being transported, minimising above ground installations and thus the environmental impact. IntelliMine will develop necessary innovative methods, technologies, machines and equipment for the safe, eco-innovative, intelligent and economic exploitation of mineral raw materials in the EU, especially at greater depths."

Jan 1, 2011

By Jerry D. Pfarr, Gary Loving, David G. McDowall

Introduction The Open Cut is one of the best known landmarks in South Dakota's Black Hills. It is the site of the original discovery of the Homestake ledge, or lead, in 1876. Between that time and 1945, the Open Cut produced about 36 Mt (40 million st) of gold ore, the majority of which was drawn from underground operations. In 1981, a drilling program was undertaken to determine how much ore the old timers left behind. The results of this study indicated an ore body made up of broken and caved ground, and solid blocks in pillars and crowns. Reserves are estimated at about 6.8 Mt (7.5 million st) of gold ore, grading at 4 g/t (0.116 oz per st). Total tonnage of material, including waste, is estimated at more than 60 Mt (66 million st). The mining plan is a combination open pit and underground operations. The bottom 78 m (255 ft) will be mined by the underground panel-caving method. The open pit was designed as a contractor operation up to the expected milling stage or the point of sustained ore production. The pit was designed to avoid disturbance of US Highway 85 near Lead, SD. In 1983, the South Dakota Board of Minerals and Environment approved the mining and reclamation plan. Test mining began in the north of the Open Cut using open pit methods. Upon completion of the test pit, Homestake Mining's board of directors approved an expanded mine plan. They committed an additional $27.1 million to prestrip the ore body that is expected to yield 23 t (750,000 oz) of gold. Project life is estimated at 15 years. Exploration program In early 1980, 10 diamond drill holes were drilled from the surface in the vicinity of the east side of the Open Cut. The reserves delineated by that drilling were too small to justify their development. A continuation of this study attempted to quantify the tonnage remaining in the bottom of the Open Cut in the crushed remnants of old stope-and-crown pillars. This was originally thought to be minable by improved drawhole methods using highly mechanized procedures. By early 1981, however, thinking turned toward surface mining methods. The effort to quantify minable ore tonnage ultimately involved drilling 385 reverse-circulation rotary drill holes. These were drilled from August 1981 to March 1983 in several groups of holes. Each group, or drilling program, had a slightly different immediate goal or purpose. The holes were drilled to various depths using truck-mounted Drill Tech 40 drills with doublewalled 76 mm (3 in.) pipe with 134 mm (5.25 in.) three-cone rotary bits. Initially, wet drilling was employed using a cyclone collection system. Since cutting recovery was not as high as it should have been, all subsequent drilling was dry. The cuttings were collected and deposited by way of a cyclone into the sample bag. The pickup for the cuttings using the three-cone bits was about 50 mm (2 in.) above the bottom of the hole. Overall cutting recovery for the drilling program was estimated at 75%. Samples were taken on each 1.5 m (5 ft) of hole drilled. Each sample was split into three 48-g (1-2/3 assay ton) charges. The accepted value was the straight average of the three charges. Because of the known "nugget effect," assays were nearly impossible to duplicate. Therefore, to validate the regular assays, a series of screen fire assays were run. Based on this method of assays and checks, it was concluded that 10% more ounces would be produced than indicated by mine grade. Test pit The northernmost portion of the mine as planned is known as the Terraville test pit. This portion was mined ahead of the rest and separately. It provided answers to questions on slope stability, reserves correlation, mill recoveries, mining costs, and surface mining conditions in various weather and ground conditions since many boulders and much timber were expected. The mining plan for this portion of the pit was successful. More ore was mined than was expected. Mixing of Open Cut ore with underground ore in the mill feed was successful. Impact on the surrounding communities

Jan 10, 1987

By J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 40 ft of advance because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation) as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011