Search Documents

By P. Zhang

Previous studies have shown that separation of clay minerals from non-clay minerals is the key to economic recovery of the phosphate from the waste phosphatic clays (slime) which represent about 20- 300/0 of the phosphate mined. Small hydrocyclones of different sizes (4" and 6") were tested for sizing the slime at +10 microns in order to remove most of the clay minerals. The effect of design variables and operating parameters were evaluated. Multi-stage cycloning and the effect of dispersant were also investigated. Chemical and mineralogical analyses of different size fractions of both the underflow and overflow samples indicated satisfactorily separation efficiency.

Jan 1, 1998

By C. F. Johnson

Nearly all of the sulphur produced in the world today is converted to sulphuric acid and 49 % is used in the manufacture of fertilizers. In the last few years we have seen the beginning of another chapter in the volatile history of sulphur as the severe shortage of 1963:-67 has been transformed into present-day surplus. Prospects for further aggravation of this situation in the years ahead seem assured. In 1970, western world production showed a rate of increase of 4 -5%, which 1S somewhat less than that of 8% for the period 1963-1967. The rate of growth of consumption dropped considerably in 1968 when the demands of the fertilizer industry fell. During the same period of time, wide-spread demands have been set in motion for a clean environment which indicates that a fundamental change in sulphur supply, demand, and even sources, is likely to result from this upheaval. The sale of sulphur by Poland to the western world has increased and for 1970 was estimated at over one million metric tons. In the next few years, increase in Canadian sulphur supply will stern from two sources;

Jan 1, 1972

By Julián M. Ortiz, Antoine Caté, Oy Leuangthong, Ilkay S. Cevik

Mineral resource classification relies on the expert assessment of a qualified person (QP) to determine which blocks of a 3D mineral resource model are classified as measured, indicated, or inferred. The decision is often based on a combination of quantitative parameters related to the estimation process and qualitative decisions based on previous experience or preconceptions not captured in the numerical model. As such, the procedure is subject to inconsistency, that is, blocks with similar qualities may end up in different categories, mainly due to the subjective nature of the approach. In this paper, we present a methodology to assist the qualified person in this task by clustering blocks with similar parameters and then classifying them into categories in a consistent and automatic manner that only requires the specification of a few hyper-parameters. The result is a consistent classification into resource categories comparable to the result of a classification done by a qualified person but fully consistent and generated in a short time frame. The procedure begins with repeatedly sub-sampling the block model to determine a distance matrix using an unsupervised random forest approach and then clustering the blocks using the associated distance matrix. Then, all the blocks in the model are classified using a supervised random forest approach, which gives a probability of belonging to each class. The initial class can be determined from the class probabilities. Support vector classification with a radial basis function kernel is utilized to smooth the boundaries between classes and define the final classification. An approach to tune the hyper-parameters of smoothing is provided. The methodology is demonstrated with two examples from two gold deposits. Results are comparable to the classification done by the project qualified person using conventional methods.

Aug 17, 2021

By W. L. Price

I. INTRODUCTION Today, there are two conflicting trends facing the designer of the bulk material handling system. The first trend is the necessity to stockpile increasingly larger amounts of bulk material (coal, ore, stone etc.) as economically as possible. Fig. 1 illustrates such a typical large storage pile. The second trend is the increasing awareness of the ecological problems of today manifesting itself in a new concern over possible air pollution from storage pile surface particles. The conflict between these two trends can become dramatic when this bulk storage pile is located near a heavily populated area. Strong winds can easily create a severe local problem by blowing the particles from the pile surface toward residential and commercial areas, igniting a crisis in public relations. (2), (3), (4). To help define our combined subject and ecological culprit more accurately, Fig. 2 shows the commonly accepted size range of dust particles. A descrip¬tion of the present state-of-the-art of dust control for large storage piles is the intent of this paper. II. OPEN STORAGE PILE SYSTEMS - ALTERNATE CHOICES AND RELATIVE COSTS In discussing the open storage dust problem and possible solutions, one obvious question arises - what are the economics of placing large bulk storage under cover? Part or this answer will be found in Fig. 3 - an approximate unit capital cost comparison between several methods of storage. It will be noted that the cost curve(s) for the closed concrete silo storage illustrated in Fig. 4 is cheaper per ton at relatively small tonnage capacities, but as tonnage increases, the open pile storage unit cost (B) becomes more economical. Curve (T) covers the cost of open storage using the plow feeder arrangement shown in Fig. 5. A gravity draw-down pile with feeders at the base as shown in Fig. 6 represents yet another open storage choice.

Jan 1, 1972

By P. J. Miranda, C. G. Anderson, L. G. Twidwell

Titanium is a metal of increasing worldwide strategic importance. The Center for Advanced Mineral and Metallurgical Processing (CAMP) at Montana Tech of the University of Montana is currently directing two titanium research initiatives. The first program, Titanium Extraction Mining and Process Engineering Initiative (TEMPER), is focused on producing low cost titanium through the identification and development of new mining, beneficiation and extraction technologies which will significantly reduce the cost of titanium production. This will directly benefit worldwide commercial applications. Secondly, CAMP is evaluating new technologies for fabrication of titanium utilizing the Free Form Titanium Fabrication (FFTF) initiative. These technologies may drastically reduce the cost and time to manufacture titanium components. Because of the high strength to weight ratio of titanium coupled with its superior corrosion characteristics, these programs will be of vital importance to expanding the commercial and strategic applications of titanium. An overview of these two new titanium initiatives will be presented in this paper.

Jan 1, 2005

Over the years, numerous studies have been conducted to characterize the floatability of coal pyrite. Unfortunately, many of the results obtained using isolated samples of coal pyrite are not directly applicable to actual coal flotation systems where liberation and entrainment may be the major factors affecting pyrite rejection. In this paper, the association of pyrite with other coal constituents is investigated, and the data are presented for feed and product streams obtained from release analysis tests. Release analysis is used to minimize the effects of entrainment. Particle distributions for each stream are presented as functions of size and composition in order to discern the behavior of free and composite particles.

Jan 1, 1992

By Verya Nasri, Mehdi Bakhshi

"Fiber reinforcement has emerged as an alternative to steel bars in precast concrete segments due to advantages such as saving cost and reducing production time while developing a more robust product with improved handling and long-term durability. ACI recently drafted a new report as the first design guideline on FRC tunnel segments to provide specific guidance for this emerging technology. ACI document offers general information on the history of FRC precast segments from tunneling projects throughout the world; a procedure for structural analysis and design based on governing load cases, and a description of the material parameters, tests and analyses required to complete the design. This paper summarizes the design considerations in this ACI guideline prepared by the authors of this paper as the main contributors. Application of this guideline to design of a tunnel with an internal diameter of 5.5 m (18 ft) results in elimination of steel bars.INTRODUCTIONPrecast concrete segments are installed to support the tunnel excavation behind the Tunnel Boring Machine (TBM) in soft ground and weak rock applications. The TBM advances by thrusting off the completed rings of precast concrete segments that provide both the initial and final ground support as part of a one-pass lining system. These segments are typically designed to resist the permanent loads from the ground and groundwater as well as the temporary loads from production, transportation and construction. Tunnel segments are generally reinforced to resist the tensile stresses at both the Serviceability (SLS) and the Ultimate Limit States (ULS). With traditional rebar, a significant amount of labor is needed to assemble the cages and place the rebar, which results in higher production costs.Fiber Reinforced Concrete (FRC) can be used to enhance the production, handling, and placement of precast concrete segments. This is because of the uniform dispersion of fibers throughout the segment to include the concrete cover, which is very advantageous for resisting the bursting and spalling stresses. These stresses develop as a result of the high loads induced on the segments during the TBM jacking process. The presence of fiber in the concrete matrix helps mitigate against unintentional impact loads during segment handling and tunnel construction operations."

Jan 1, 2016

By M. B. Haggerty, R. J. Sheets, F. Abbasy

To address coal refuse tailings storage needs for a mine operation in western Canada, a feasible solution was to convert excavated open pits into tailings cells. A slope stability investigation and design study were completed to determine the necessary width and slope geometry for in-situ native plugs as the impoundment embankment. The native plugs separate the previous open pit from the current active open pit. This configuration allows for the deposition of refuse tailings in the previous pit while allowing mining to safely continue “downstream” of the temporary impoundment. As mining progresses, each subsequent pit will be filled with refuse tailings; thereby, buttressing the upstream slope of the previous native plug. Although these cells are excavated, and the timeframe for downstream exposure is relatively limited, the native plugs are classified as dams and must be designed to meet applicable safety of dam standards since they impound water and tails above mining personnel in the subsequent open pit. The presentation and paper will discuss the investigation and analysis conducted to develop the geotechnical and hydrogeological design recommendations.

Mar 2, 2022

By S. Hadley, M. Placha, M. Mishra, V. Choudhry

Under a DOE-funded project, four advanced flotation technologies (the Jameson cell, the Outokumpu HG Tank Cell, an open column and a packed column) were evaluated at the benchscale to identify the technology or combination of technologies that best improved fine coal recovery and reduced processing costs. The results indicated that two-stage application of the Jameson and packed column cells provided the optimal performance. Subsequently, proof-of-concept scale testing was conducted at the Cyprus Emerald Coal Preparation Plant. The results confirmed that levelized production costs were lower using two-stage cleaning with the Jameson cell followed by the packed column.

Jan 1, 1999

By C. H. Perbix

[On Pier D in the Port of Long Beach, California, the Port of Long Beach has built a new bulk cement distribution terminal. The facility is operated by Pacific Coast Cement Corporation, who designed the complex and leased it from the Port of Long Beach on a 40-year lease. At one bulk cement is unloaded from vessels carrying from 12,000 to 30,000 t. The unloading is performed with pig speed mechanical unloading equipment and delivered into a concrete silo complex with, a capacity of 50,000 t. From the silos, bulls cement is loaded into trucks for delivery. The facility was completed in September 1981.]

Jan 1, 1983

By Utku Gumus, Ertan Bostanci, Hanifi Copur, Ahmet Rüfai Bilgin, Ugur Altay

"Field observations on replacements of 12-inch constant cross-section double disc cutters in Tuzla Wastewater Tunnel excavated by an EPB TBM with 3.151 mm excavation diameter excavating hard rock are summarized. Cutter life is correlated to rock’s uniaxial compressive strength and Cerchar abrasivity index, and TBM operational parameters. Number of cutter replacements, average cutter replacement rates and types of cutter damages are summarized. The relationships between cutter life and rock properties and TBM operational parameters are analyzed by single variable regression method. Detailed analysis between chainages 1+200 and 1+982 km indicates that average cutter consumption rate is 35.7 m3/replacement (4.6 m/replacement). Cerchar abrasivity index and uniaxial compressive strength does not indicate any meaningful relationship with cutter life. Penetration per revolution and field specific energy might be used for predicting lives of constant cross-section double disc cutters. However, additional data is required to generalize the findings of this study. INTRODUCTION Cutter life / replacement and/or consumption rates in terms of cutter cost and replacement time loses is one of the most important parameters affecting excavation performance of mechanical excavators, especially of TBMs used very widely and equipped with usually disc cutters. Predicting cutter cost is a very important task in especially feasibility stage of tunneling projects. Basic parameters affecting cutter life can be classified into 3 general groups as geological and geotechnical, excavation machine (TBM) related, and operational parameters (Bilgin et al., 2013). The geological and geotechnical parameters are the most dominant ones among them. The machine related parameters should be arranged in accordance with the expected geological and geotechnical conditions for the best TBM excavation performance and minimum cost."

Jan 1, 2016

By R. Frim, S. D. Ukeles

The present U.S. production of bromine is from inland brines located in Arkansas and Michigan. The most concentrated domestic brines (up to 5,000 ppm bromide) are situated in Arkansas. Less concentrated brines (about 2,500 ppm bromide) are located in Michigan. The amount of bromine sold or used in the United States came from three companies operating in Arkansas and Michigan. Arkansas, with its six plants, was the leading U.S. state in bromine production. Bromine being the leading mineral commodity valuewise produced in the state. The Michigan bromine production was a byproduct of magnesium compounds production.

Jan 1, 2006

By William G. Pariseau

Few departments of mining, metallurgical or petroleum engineering in the United States have critical mass. Cost per student credit hour (SCH) in departments across the country are usually the highest among engineering departments, which are the highest on campus. Almost all departments are operating at fixed costs and enrollments could easily double without incurring much additional cost. However, the cost per SCH would remain unacceptably high and the probability of doubling enrollment is nil. Declining enrollment is a more likely future. The pressure to reduce SCH from university administration is unrelenting. And it has the potential for doing serious damage to program quality when standards and requirements are lowered in attempts to maintain enrollments and increase retention.

Jan 1, 2002

By F. Habashi

Brazil is a major mineral and metal producer, has magnificent fauna and flora, and superb architecture. In 1693 gold was discovered in Ouro Preto and Brazil produced about half of the world's gold. In 1726 diamond was discovered in the region of Tijuco in the Province of Minas Gerais, 150 km east of Bello Horizonte. The country became independence from Portugal in 1822 as the Brazilian Empire. In 1876, an Englishman succeeded in obtaining from the Amazon region seeds of rubber trees and secretly transferred them to England, where they were planted in the royal gardens at Kew. Some of the seedlings which spouted were sent to Ceylon and Singapore. Thus, began the rubber industry in the East. Today, Brazil is the largest producer of niobium, and produces a large number of other metals. The Mineral Research Center in Rio de Janeiro is the countries main Government establishment for mineral research. The country has been a republic since 1889 with its capital in Brazilia.

Jan 1, 2009

By A. Navarra, F. Mucciardi, H. Marambio, R. Parra, F. Oyarzún

"Discrete event simulation (DES) is an appropriate framework for the plant-wide analysis of copper smelters. These smelters apply a common set of chemical reactions: copper-iron sulfides are blasted with oxygen-enriched air, sending the iron into a slag phase and the sulfur into the offgas. Moreover, conventional copper smelters exhibit similar operational dynamics: a smelting furnace operates continually, feeding into an alternating set of converters that produce batches of blister copper. The thermochemical and operational commonalities of copper smelters are integrated within the DES framework. This serves as a common basis to begin evaluating the system dynamics of individual smelters. For complex problems, the simulation framework should be developed in phases, incorporating feedback from different personnel who have complementary perspectives. Sample computations are provided in this paper based on the Hernán Videla Lira smelter, whose production is constrained by meteorological conditions. IntroductionWorld copper production is approximately 18.5 million t/y (Brininstool, 2015), worth $80 billion a year. Out of this total, 75 percent comes from the pyrometallurgical processing of sulfide minerals (Fig. 1), which occurs in copper smelters. The remaining 25 percent is from the hydrometallurgical treatment of oxides and complex ores (Rotuska and Chmielewski, 2008), which uses solvent extraction and electrowinning.The current paper describes the pyrometallurgical processing, recognizing that the underlying thermodynamics and kinetics are well known (Degterov and Pelton, 1999), with the notable exception of minor element transport, such as arsenic (As), antimony (Sb), bismuth (Bi), silver (Ag), gold (Au). The latter is an ongoing area of research, as smelters are faced with increasingly complex ores (Devia, Wilkomirsky and Parra, 2012; Swinbourne and Kho, 2012). This paper focuses on the system dynamics of copper smelter operations, which has received considerably less attention than the chemical thermodynamics and kinetics.Smelter engineers and managers may contribute to the sustainability of their plant by improving their understanding of operational system dynamics. Indeed, we have prompted smelter improvement projects (Navarra, 2016; Navarra et al., 2016; Navarra and Mendoza, 2013) simply by adapting methodologies that are commonly used in other sectors. These previous works incorporate principles from computer-integrated manufacturing (Groover, 2000) and theory of constraints (Dettmer, 2007), featuring the use of discrete event simulation (DES)."

Jan 1, 2017

By M. Stuart

The copper-silver-mercury orebody of Gortdrum Mines (Ireland) Limited is located 3 miles north of the town of Tipperary in the Republic of Ireland. A drilling programme from 1964 to 1966 delineated an ore¬body of 4.19 million tons of copper ore assaying 1.19% Cu and 0.75 ozs per ton Ag, which could be mined from an open pit. Testwork having shown that the ore was amenable to conventional flotation techniques, it was decided to build a concentrator of 500,000 tons ore per year capacity. Stripping of the open pit commenced in 1966 and in the autumn of 1967 the concentrator started up. The first shipments of concentrates were made to the smelter in Europe in late 1967. In the spring of the following year, word was received from the smelter that these early shipments contained between 1% and 2% Hg, and that the smelter could not accept further shipments of this quality.

Jan 1, 1973

By N. Prenn

"INTRODUCTION The 2014 SME Guide for Reporting Exploration Results, Mineral Resources, and Mineral Reserves (the SME Guide) has been adopted by the Society for Mining, Metallurgy, and Exploration, Inc. (SME). The SME Guide is recommended as a minimum standard and a basis for developing industry best practices in the classification of Mineral Resources and Mineral Reserves for public and private purposes. The Guide is therefore strongly recommended to be used by members of this organization. The SME Guide was updated in 2014 to include CRIRSCO (Committee for Mineral Reserve International Standards) core definitions, and it is envisioned that the U. S. Securities and Exchange Commission (SEC) will adopt the SME Guide in 2016. However, as of the end of 2015, the SEC Industry Guide 7 remains the standard for the U.S. reporting of Mineral Reserves. This paper will cover the classification of Mineral Resources and Reserves, a discussion of Modifying Factors, and the classification definitions and guidelines. The definitions and guidelines contained in this report are from the SME Guide. FRAMEWORK FOR MINERAL RESOURCE AND MINERAL RESERVE CLASSIFICATION Figure 1 illustrates the classification of Mineral Resources and Mineral Reserves using the Guide. Mineral Resources are divided into three classifications of Inferred, Indicated, or Measured while Mineral Reserves include Probable and Proven classifications. These classifications reflect improved knowledge and confidence of the deposit from the top of the figure to the bottom. In other terms, the deposit risk also decreases from top to bottom.The relationships in Figure 1 reflect different levels of geoscientific knowledge and different degrees of technical and economic evaluation. Mineral Resources can be estimated on the basis of geoscientific information with input from other disciplines to establish reasonable prospects for eventual economic extraction. It was not too many years ago that the classification of a Mineral Resource was based on the evaluation of a limited set of factors that included spatial drill hole and grade distribution (kriging variance, as example), distance to the closest hole, and number of samples used to estimate a block grade. These are still important considerations, but classification following the Guide must also take into account sample integrity, sample QAQC, database integrity and completeness, geological understanding, and geological and grade or quality continuity. In addition, a general consideration of the Modifying Factors, to establish reasonable prospects for eventual economic extraction, adds complexity to the classification."

Jan 1, 2016

By R. J. Roman

The results of column leaching tests on 3 different mixed oxide/sulfide ores from a Chilean deposit are presented. The 3 samples contained different ratios of oxide copper minerals to chalcocite and chalcopyrite. The results of the column leach tests are interpreted in light of the shrinking core model for coarse particle leaching. The copper recovery from the oxide minerals and the sulfide minerals each conforms to the shrinking core model with the total recovery equal to the weighted average of the individual minerals. The use of column test results to predict field heap leaching results using the multi-mineral shrinking core model is discussed.

Jan 1, 1993

By J. O. Marsden, J. H. Gourdie, J. R. Arnold, J. G. Mansanti

During the testing and design of the Gold Fields' Chimney Creek mine, it was found that a much higher carbon loading was possible with CIC (carbon-in-solution columns) than with CIP (carbon-in-pulp). In an effort to keep the carbon handling minimized, an emphasis was put on forcing gold to the CIC circuit rather than the CIP. After considerable study, it was found that a circuit with two thickeners and an interstage leach would force 90% of the gold to CIC. Computer modelling indicates that the benefits of the hybrid circuit include higher recovery, less carbon handling, fewer leach tanks, and lower reagent costs.

Jan 1, 1990

By S. Veeramasuneni

The interaction of soluble salt particles in their saturated brines is of interest from both a fundamental and practical perspective. The state of dispersion/aggregation of alkali halide particles as determined by optical microscopy can now be described based on non-equilibrium electrokinetic measurements for alkali halides. These results indicate that the sign of the surface charge has a significant effect on the extent of particle dispersion/aggregation. Atomic force microscopy (AFM) is now being used to directly measure the interaction forces responsible for the stability of these alkali halide aggregates observed in optical microscopy studies. These experimental results can be explained based on the interfacial polar interaction theory. In this regard the nature of such particle interaction forces at high ionic strengths are examined to improve our understanding of these systems.

Jan 1, 1997