Search Documents

By M. Fan

Coal has in general a wide range of density from minus 1.3 to plus 2.0 g/cm3 because of its variations in purity, rank, and porosity, etc. The coal density has great impact on froth flotation performance, but much less attention has been paid to particle density than particle size. Our previous research results demonstrated that cavitation-generated nanobubbles around 700 nm in diameter can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubble on the flotation performances of different density fractions (minus 1.3, 1.3-1.4, 1.4-1.5, 1.5-1.6, 1.6-1.8, 1.8-2.0, 2.2-2.2, and plus 2.2 g/cm3) of coal was investigated using a bank of 10-liter flotation cells, a specially designed 50-mm-inside-diameter column, and a 152-mm-inside-diameter column. It was found that nanobubble has the biggest impact on the flotation performance of 1.4-1.8 g/cm3 medium-density coal particles.

Feb 23, 2014

By S. S. SHINDE, P. C. JIKAR, N. B. DHOKEY

Mill scale is an oxide waste product of the steel mills, which contains around 70% iron and other allied impurities. In the present context, a dynamic prototype counter current reactor (CCR) has been used for experimentation and simulation of particle bed by using discrete element method (DEM). Mill scale was pulverized to ASTM mesh range 140 (106 μm)/ + 270 (53 μm), and then it was oxidized in CCR to make single oxide Fe2O3 phase by maintaining required thermodynamic conditions such as pure oxygen at 1100 °C. Then this oxidized powder was subjected to reduction reaction in CCR having gas mixture ( H2:N2) ratio of 1:4 at 875 ± 5 °C for filling degree (fd) and reactor revolution (ω) ranging from 5.38 to 16.14% and 2 to 5 rpm, respectively. A creeping fluid flow condition (Re ˂ 1) and natural heat convection (Gr/Re2 ˃˃ 1) has been maintained while undergoing solid–gas reaction. Besides particle bed behavior has been quantified by Froude number (Fr) for the optimum operating window. The simulation was validated by the experimental results of reactor reaction product by X-ray diffraction (XRD) and scanning electron microscope (SEM) images. Prevailing heat transfer mechanism and reduction reaction mechanism has been established for solid–gas counter current conditions.

Nov 22, 2021

By D. Boreck

The Bureau of Mines is conducting research on the feasibility of incorporating in situ stope leaching into active underground metal mines. Stope leaching, a modified in situ leaching technique, proposes to recover metals by leaching fragmented ore in existing underground openings and collecting and processing the metal-bearing solution to recover the valuable metals. If leaching solutions escape from the stope, either through geologic discontinuities or highly permeable zones in the rock, valuable metals dissolved in the solution may be lost. Escaping solutions may also contaminate ground waters. Consequently, in fractured rock, the characteristics of the fractures in the vicinity of the leaching stope must be understood before introducing actual leach solutions into the stope. Effectively characterizing a rock mass requires the integration of several disciplines including structural geology, borehole geophysics, hydrology, geochemistry, and mining engineering. This paper will focus on the general geologic and geophysical techniques that can be used to characterize the rock mass at an underground simulated stope leaching site. The results of several geophysical logging methods, tested at the site, are compared to the geologic core descriptions. Then, the? effectiveness of the different geophysical techniques in delineating fracture zones will be assessed. Knowledge gained through the geologic and geophysical analyses can be used to supplement results from hydrologic testing. This information can also be utilized in designing blast patterns and developing strategies for controlling or blocking movement of escaping leach solutions.

Jan 1, 1991

By Shankar S. Hegde

In many areas of the United States much of the most readily minable coal is nearing depletion, while at the same time, increased national attention is being given to coal as a major alternate energy source. If some of the thinner, more erratic, deeper and lower quality coals, which comprise the great bulk of U.S. resources, are to be mined efficiently and economically, greater attention must be devoted to careful planning of mines and to preparation facilities. One of the cornerstones to careful and successful mine planning is precise knowledge of coal thickness and areal distribution, roof and floor quality, and seam quality. Data on which this knowledge is based are obtained from various borehole techniques and, in some cases, seismic methods. Despite the many technical innovations that have been made in acquiring subsurface data, little attention has been given to the problem of systematic storage and retrieval procedures of the data and assembling them in a form that can be used for various computer mapping programs now available. (See Bilter and Martin, 1977; Bryant and Zobrist, 1977 and Farrell and Wherry, 1978). The purpose of this paper is to describe a series of user oriented programs developed over the past five years which are specifically designed for precise logging of rock core, accurate storage and retrieval of this data, correlation of seams between logs, tagging seams, computer assisted data posting of maps and preparing maps and profile sections for report illustrations. The entire system stresses increased precision and speed for a series of operations which are now largely manual, time consuming and prone to error.

Jan 1, 1980

By Devin Burns, Saima Ghazal, Michael Owusu-Tweneboah, Kwame Awuah-Offei

Trust in AI systems and the nature and amount of information about the system can influence decision-making. It is, therefore, crucial to understand how AI-powered monitoring systems (e.g., gas monitoring systems) influence miners’ trust and decision-making in emergency evacuation. This work focused on measuring the differences between how participants respond to a simulated underground mine emergency evacuation situation when warnings are represented as coming from a human or AI-based monitoring system. We also manipulated the amount of information participants received about the system, yielding a 2×2 between-participants survey design. The participants received an alert message about rising gas levels in a mine and provided a response on how they would react and reported their perceived safety. We also asked questions to assess their trust in, preference for AI over human-based gas monitoring systems, and whether they are willing to delegate the duties of underground gas monitoring to AI systems. The experiment results show the amount of information had a significant influence on miners’ trust and decision-making. The safety perception of participants based on age, number of children and ethnicity was significantly different from one category to another. This work provides valuable insights as the mining industry deploys AI systems to aid mine safety.

Feb 1, 2025

By T. Acton

The Zarafshan/Newmont Joint Venture is currently operating in the Republic of Uzbekistan producing in excess of 400,000 oz. of gold per year from low grade oxide ore stockpiles adjacent to the Muruntau open pit gold mine located in the Kyzylkum desert of central Uzbekistan. Four stage crushing and screening produces a final product for heap leaching, Merrill-Crowe processing, and local refining for International market export. The Zarafshan/Newmont Joint Venture is the first major commercial project of its kind in the former Soviet Union to be successfully negotiated, engineered & constructed, and placed into continuous operation,

Jan 1, 1997

By Lloyd W. Trevoy

Commercial production of heavy minerals from plant tailings streams is undergoing study by Syncrude Canada Lrd. When tar sand from an open pit mine is processed and up- graded to synthetic crude oil, heavy minerals can be recovered from the extraction circuit and can be upgraded to provide concentrates of zircon and titanium minerals. The titanium minerals concentrate consisting of a mixture of ilmenite, leucoxene and rutile, could be utilized as recovered or could be upgraded to synthetic rutile. With the construction of further synthetic crude oil plants in Western Canada a large reserve of heavy minerals will become available for utilization.

Jan 1, 1981

By Robert Charles Alfred

Evolution is continuing in the field of rock drilling, Campbell Limestone Company is experimenting in the higher air pressure phase of drilling, It has been determined that there is a definite relationship between Air Pressure, Penetration Rate, Bit & Tool Wear and Life, In our drilling we have determined that &e higher air pressure gives a better penetration rate with less bit wear per foot. Drilling with 180 to 200 PSI air pressure, instead of 100 PSI for air and/or churn drills, has decreased our primary costs by approximately one half.

Jan 1, 1963

By William G. Pariseau

The purpose of this paper is to present a discussion of the various approaches that can be utilized in the study of mine subsidence phenomena. Attention is focused upon the rational selection and use of laboratory models. Broadly interpreted, mine subsidence is the deformation of the rock mass enclosing the mine. Depending upon a number of factors, the movement of the subsiding rock mass may be such as to disrupt gas and water lines or other buried utilities, to damage surface structures such as buildings and bridges, to dislocate streams, roads, and rail lines, to aggravate acid mine drainage and fire problems, and to generally mar the landscape. It is clearly a problem that no mine manager can safely ignore. It is also a problem that will grow with the general population increase. In the following, a summary review of past and present approaches to subsidence studies is given. The possibilities of duplicating subsidence phenomena in laboratory models are examined, and an analysis of a particular type of model is presented. Some preliminary results obtained from a model of the particular type analyzed are then discussed.

Jan 1, 1968

By Huiqin Yao, Dongmei Liu

The study investigated the potential use of low activity circulating fluidized bed combustion (CFBC) ash and phosphate tailings for the production of a filling material based on the cement. The phosphate tailings were used as aggregate and consolidated by cement and CFBC ash. The results showed that the bleeding rate and fluidity of all mixtures decreased with the increasing the amount of CFBC ash. The fluidity of filling slurry is highly related to the experimental factors such as the content of sulfur solid ash, B/A ratio, and mass concentration. The replacement of CFBC ash ranging from 20 to 40% led to a significant decrease in setting time and an obvious increase in compressive strength, but the above effect was obviously weakened when reducing the mass concentration and B/A ratio. The hydrated calcium silicate gel and ettringite generated from the hydration of cement and CFBC ash were the main sources of strength for the filling materials. When the recommended proportion was 1/6 binder/phosphorus tailings ratio, 76% solid content, and 40% CFBC ash replacement, the filling material still met demands on working and mechanical properties; at the same time, the utilization of CFBC ash and phosphorus tailings was maximized.

Oct 11, 2021

By J. F. T. Agapito

Stability in Exxon's Colony Pilot Mine in the Piceance Creek Basin, Colorado has been monitored by periodic pillar stress-determinations End roof-to-floor convergence measurements since 1971. Pillar failure has caused marginal stability in some areas of the mine. Measurements taken during the process of failure provided valuable information on the in-situ pillar strength and long-term behavior of the mine structure. Four pillars were reinforced by 32 mm (1-1/4 in) diameter tensioned grouted bolts to increase long-term stability in the northern area of the mine. Stability of this area is necessary because future plans envision its use as an exit/access and ventilation exhaust. Computer analyses were performed to help evaluate the effect of pillar reinforcement on long-term stability. Results indicate that bolting is particularly useful in stabilizing failed pillars, but its effects are significant only in the immediate area of the pillar. The projected significant decrease in deformation of two extensively failed pillars near a main entry indicates that bolting reinforcement will assist the long-term stability of the opening.

Jan 1, 1985

By S. J. Schatzel, V. Gangrade

A ventilation research study was conducted by the National Institute for Occupational Safety and Health and a cooperating trona mine in the Green River basin of Wyoming, USA. The mine operation uses the longwall mining method in trona bed 17, a commonly mined unit in the region. The longwall face length is 228 m (750 ft), and caving on the face occurred up to the back of the longwall shields. The mine is ventilated using a main blowing fan and a bleeder shaft. For this study, sulfur hexafluoride (SF6) tracer gas was released in two separate monitoring experiments. For the first experiment, tracer gas was released on the face, this test focused on airflow along the longwall face of the active panel. Face test showed the airflow patterns to be more complex than just head-to-tail flow in the main ventilation air stream on the active panel. For the second experiment, tracer gas was released 2 crosscuts inby the face on the headgate side, this test focused on gas transport in the mined-out portion of the same active panel. Gob test showed a pathway of movement through the front of the active panel gob that moved outby from the tailgate corner. The primary pathway of tracer gas movement in the active panel gob was towards the headgate and tailgate bleeders and out of a bleeder shaft. The rate of movement towards the back of the gob was measured to be 0.19 m/s (37 fpm).

By C. R. DeGennaro, Yongjun Zhang, J. Bickson, J. L. Carr, Chenming Zhou, J. R. Srednicki, B. Lambie, M. Girman, J. A. Galanko

Between 2005 and 2021, surface mining haul trucks were involved in 54 fatal incidents in the United States [1]. Collision warning and avoidance systems (CXS) can help haul truck operators navigate their route safely. The evaluation of CXS object detection performance for surface mining haul trucks relies on the positional accuracy of the ground truth instrument. As part of a holistic approach, researchers from the National Institute for Occupational Safety and Health (NIOSH) characterized the accuracy of a global navigation satellite system (GNSS) that serves as the ground truth instrument to determine object position and velocity in CXS object detection performance testing. We used precision surveying equipment to establish ground truth points for comparison with GNSS data collected for static positional measurements and reduced-scale straightline vehicle dynamic tests. We conducted these tests with real-time kinematics (RTK) and then satellite-based augmentation systems (SBAS). For the dynamic tests, we measured a distance error of 1.34 m (4.40 ft) using RTK and 1.50 m (4.92 ft) using an SBAS. This research will provide CXS manufacturers and CXS researchers a basis for evaluating the positional accuracy of CXS. Note that we did not evaluate any CXS in this experiment.

Feb 1, 2024

By James E. Lonergan

Linear goal programming is a multi-objective optimization technique where the constraints of a linear programming formulation of a problem are considered as additional objectives. The optimal solution is the one that comes closest to satisfying all the objectives. An interactive computer program was written to utilize this technique in solving the feed blending problem faced by power plants de- pendent on multiple sources of coal supply. This program determines the amount of coal from each supplier to utilize in the blend. Examples of the use of the program in both long and short term coal procurement planning scenarios are given.

Jan 1, 1984

There are presently in use many grinding mill control schemes and concepts. This paper presents one operating method of controlling the particle size of the cyclone overflows for proper metallurgical results and controlling the level of the cyclone feed sump and new feed rate to obtain lowest unit cost of finished (ground) material which is usually at the maximum grinding mill throughput. This system stresses simplicity of field instrumentation and control strategy. Both of these factors lead to better operator understanding and acceptance. The low capital investment of this system also makes it more attractive at the Buick Concentrator when compared to other more complicated systems utilizing mass flow measurement and a computer to calculate circulating load and infer particle size. Furthermore, it has the advantage of utilizing an actual measurement for control, rather than a difficult-to-maintain inferred value. There are several reasons for maximizing mill throughput at Buick. The milling rate before automatic control was too low when compared to mill throughput increases planned for the future. Through this new operating system, it appears Buick will not have to make major changes of mill motors and speeds to meet the increased? production rate. Also, since power costs continue to escalate, it is desirable to maximize the throughput to the grinding circuit and reduce overgrinding to achieve a reduction in power cost per ton of ore milled. Presently, 45% of the concentrators' total power is consumed in this grinding circuit.

Jan 1, 1977

By E. L. Piper

Natural graphite has been known for many centuries, having first been reported as a distinct mineral form by Gessner in 1565. At that time, graphite was used extensively as pencil "lead" because of the ease with which it marks paper. It is a black, unctuous material found as flakes, lumps, or needles in scattered locations throughout the world. The less crystalline, or "amorphous", natural graphites are thought to have been formed from coal under conditions of high temperature and pressure. The more crystalline varieties, such as those mined in Ceylon, probably were precipitated from molten solutions or were pyrolyzed from gaseous carbon compounds. Recognition of the good thermal and electrical conductivity of graphite, together with its highly refractory nature, led to an increasing number of appli¬cations for this material. Clay and pitch bonded natural graphite has been used in crucibles, refractories, foundry facings, and other high-temperature appli¬cations. These forms constitute the most important current uses for natural graphite in the United States. Other products containing natural graphite include batteries, lubricants, pencils, brake linings, etc.

Jan 1, 1973

By E. J. Wade

My subject is gold price forecasting and monitoring as an important aspect of gold marketing. While I 'm specifically addressing gold, it is understandable that many other commodities could be readily substituted. Gold marketing must be studied as three distinct processes, and it is my intention to cover each of these processes in turn. First I?ll cover the process of gold price monitoring and forecasting in some detail. In order to select a method, or combination of methods, to be used to sell gold a determination of the future price profile is essential. The profitability of the sales effort will be determined, to a large extent, by how accurately the future price behavior of the gold market has been forecast.

Jan 1, 1985

By Albert F. Duzy

Recently there have been some problems associated with hot coal in shipments from the USA to overseas markets. This paper will serve several functions. First, a brief review is presented, together with a selective bibliography. Second, a thorough discussion of coal oxidation is covered. Third, potential effects of storage are presented and, lastly, methods are suggested for the safe storage and bulk transfer of coal. The scope includes coal storage for power plants.

Jan 1, 1983

By James L. Hendrix

This paper is intended to give the reader an update on the work being done at the Mackay School of Mines about the fate of cyanide on precious metals mill tailings waste. During the last two years several tailings impoundments have been sampled and analyzed for total and free cyanides. From our sampling program we are beginning to learn valuable information concerning the fate of cyanides in precious metals mill wastes. Included in this paper is a detailed description of our sampling and analytical techniques. Also, some of the data obtained from five sites are given.

Jan 1, 1986

By M. A. Mahtab

This paper presents the results of a parametric study of the influence of natural features (stress field, rock strength, and strength and orientation of fractures) as well as the influence of induced features (undercut span, boundary slot, and other boundary-weakening measures) on the cavability of an undercut block of ore in mining by the block-caving method. The two-dimensional finite element analysis technique was used for this study. A coarse "mesh," along with linear homogeneous assumptions for rock properties, was used to model the problem of initiation of caving in a block of ore. Interpretation of the test results suggests that weakening the "abutments" of the block as well as certain orientations of natural fractures exercise significant influence on cavability. These findings hold promise for immediate application to known situations in block-caving mines.

Jan 1, 1975