Search Documents

By H. W. Hitzrot

Introduction Mechanical classifiers consist of a settling tank with parallel sides and a sloping bottom equipped with a mechanism which continuously agitates the pulp and removes the settled solids. The functions served by mechanical classifiers include the following: (1) allow the particles larger than the desired size to settle in the tank and provide an overflow product with a minimum of oversize particles, (2) produce an overflow product of sufficiently high solids content to meet the requirements of the subsequent processing steps, (3) agitate the pulp and permit separation of the entrapped undersize particles so they can report in the overflow product, and (4) drain and remove the underflow solids from the settling pool. Various types of mechanisms have been used to agitate the pulp and remove the settled solids, which include: (I) endless belt and chain drags, (2) reciprocating rakes, (3) helical flights mounted on a rotating shaft which extends through the settling pool, (4) helical flights inside of a rotating drum which contains the classifier pool, (5) troughed conveyor belts forming the settling pool in the concave curve of the belt closely following the tail pulley, and (6) low-speed impellers agitating the underflow settled in the apex of cone-type mechanical classifiers.23 The principal use of mechanical classifiers has been in closed¬-circuit wet grinding; however, this application has been widely displaced over the past few decades by the hydrocyclone. The hydrocyclone installation, including its feed pump, offers lower capital costs and requires less floor space. Nominally it produces an overflow prod¬uct of higher solids content, compared with a mechanical classifier, for comparable classification size up to 400µm (35 mesh). However, these advantages of the hydrocyclone are being gained at the sacrifice of some of the advantages of the mechanical classifier. The mechanical classifier requires less power and has lower maintenance costs than the hydrocyclone and its feed pump. The underflow product from the mechanical classifier can have a higher solids content and contain less entrapped undersize particles than the comparable product from the hydrocyclone. Consequently, it is capable of operating at a higher classification efficiency. A reduced circulating load24, 25 results under these conditions in a closed-circuit grinding application. Other applications for mechanical classifiers include desliming, dewatering, and washing operations. Sand-slime separation may be achieved using one or more stages of mechanical classifiers. Typical applications would include washing and deslimining of concrete aggre¬gate or sand; glass sand; abrasives; oyster shells; phosphate rock; iron, nickel, and chromium ores; alumina; zeolites; solar salt; and precipitates from chemical processing. As an example for the latter, Bitzer26 recommended the use of mechanical classifiers for countercur¬rent cementation-in-pulp of copper from the leach liquor. Similarly, mechanical classifiers are used in uranium processing27 for separation of the barren sands from the pregnant leach solution. Depending on the particle size and the effectiveness of the sand¬slime separation, the sand product from mechanical classifiers may be drained to solids content approaching 84%. Thus, mechanical classifiers are frequently used as dewatering equipment for various applications, such as: 1) Make a product having suitable solids content for subsequent transport by belt conveyor. 2) Provide a drained product to reduce cost of drying. 3) Provide a drained, washed, heavy sand product for return to the circuit. 4) Recover fine values from dilute plant effluents from coal, sand, phosphate-rock, and iron-ore washing plants and from steel-mill flue¬dust scrubbers. 5) Drain residual reagents of a preceding process stage prior to conditioning with reagents of different characteristics, e.g., cationic¬anionic flotation of phosphate rock, iron ore, etc. Design and Operating Features The proper selection of mechanical classification equipment re¬quires that the properties of the solids and liquid are adequately de¬fined. The following descriptive information regarding the solids is desired: feed rate, chemical and physical composition, density, tem¬perature, size analysis, and desired separation size. For the liquid used, the following data would be needed: feed rate, density, viscosity, pH, and temperature. Settling Area. The pool area required to permit a particle larger than the separation size to settle depends on the density and shape of the particle and on the density and viscosity of the pulp within the classifier pool. These criteria of the solids and pulp determine the settling rate which, in turn, determines the settling area required. Determination of the settling rate by long-tube batch tests can be used to calculate the settling area. A theoretical approach for estimat¬ing the settling area requirements is discussed in Chapter 1, Classifica¬tion Theory. This procedure can be used when neither test data nor empirical data from similar operations are available. Data on settling-area requirements and settling rates have been compiled by the manufacturers of mechanical classifiers. The approxi¬mate settling area required for a particular separation size can be estimated by using the curve shown in Fig. 65. This curve applies for closed-circuit grinding applications. For dilute velocity classification in open circuit, desliming, the length of the overflow weir, W, multiplied by the weir's mean distance from the feed opening, E, is used as the design criterion, instead of the settling area, in sizing the classifier. The area requirements, W X E, for dilute velocity classification can be expressed in terms of volumetric flow, Q, and settling rate, Rs, as follows: W x E = Q/(18.06 Rs) where W and E are feet, Q is gallons per minute, and Rs is inches per second. Overflow Weir. The hydraulic head, and thus the velocity at which the overflow crests the overflow weir, is one of the factors controlling the particle size of classification. Consequently, the length of the overflow weir must be designed to provide the overflow velocity which allows the particles larger than the desired size of classification to settle in the working area of the pool. Obtaining the necessary

Jan 1, 1985

By C. S. Thompson, P. A. Ciullo

Pyrophyllite is a naturally occurring hydrous aluminum silicate with the molecular formula SiO,,AI,,(OH), or, as more commonly expressed, the oxide formula A120,~4Si02~H20. Pyrophyllite is rarely found in deposits as the pure mineral and is often intimately associated with quartz, sericite, kaolinite, and diaspore. These associated minerals, to a large degree, help determine the most appropriate commercial application for a given pyrophyllite ore. Structural similarities plus the generally soft platy nature of pyrophyllite has in the past caused it to be included with talc in applications and production data. The Minerals Yearbook, published annually by the US Bureau of Mines (USBM), still reports on talc and pyrophyllite together, although admitting that they do not share the same uses. Pyrophyllite has also at times been considered a clay mineral because of its structure and chemistry. The refractory properties of pyrophyllite have been known for nearly 200 years, but it has only been in the past 60 to 70 years that a variety of applications have been developed to exploit the unique characteristics of this mineral. Worldwide, pyrophyllite is a component of refractories, whiteware, foundry mold dressings, pesticides, paint, plastics, rubber, cement, fiberglass, and soap. Historical Overview The most salient refractory features of pyrophyllite are its low coefficient of thermal expansion, high thermal conductivity, low moisture expansion, and good resistance to corrosion by molten metals and basic slags. One of the first recorded uses of this mineral was as firebrick in Japan in the early 1800s. This followed its discovery in 1797 on Mount Omotoyama at the site of the present Mitsuishi mine. In addition to firebrick, sawn blocks of ore were used for carvings and in the manufacture of slate pencils and signature seals. The Mitsuishi mine is still one of Japan's largest. By the mid-1800s, refractories were being made in Japan from roseki (a pyrophyllite-bearing ore) for the construction of metal melting furnaces. The mineral did not get its name until 1829 when R. Herman, testing a sample of supposed talc from the gold-quartz veins at the Berezovo deposit in the Urals, showed that it was actually an aluminum silicate and designated it pyrophyllite. This name was derived from the Greek pur for fue and phullon for leaf, in allusion to the effect of heat in causing separation of the laminae in foliated varieties (Mellor, 1927). The exact date of the discovery of pyrophyllite in the United States is uncertain, but it is believed that the talc and soapstone deposits noted in an 1827 report on the geology of the slate belt of North Carolina were actually pyrophyllite occurrences (Olmstead, 1827). Pyrophyllite was first used in North Carolina on a local basis in the early 1800s. Blocks were sawn and cut for use as stove linings, mantels, chimneys, fireplaces, and gravestones. This was the material of choice because it did not shrink when heated, but cut easily and hardened as it weathered. Pyrophyllite crayons were sold commercially by local gold miners for steel marking and as tailor's chalk from about 1800 until 1922. It was during this period that pyrophyllite was discovered near the town of Hemp (later renamed Robbins), NC. The large quantity of scrap resulting from the sawing of crayons at this deposit prompted the construction in 1921 of a grinding plant. The ore scrap was ground to fine granules and sold to asphalt producers to prevent shingles from sticking together. By the mid-1930s, milled pyrophyllite from North Carolina was also being successfully utilized by the ceramics industry in whiteware for its low cost and ability to shorten firing time. Also during the 1930s, pyrophyllite was first used in kilncar furniture in the United States. Canada was another early entrant in the pyrophyllite business. Mining at the Foxtrap deposit on the Avalon Peninsula of Newfoundland began in 1904, with ore shipped to the United States. Production from this deposit was mostly sporadic in the ensuing years until 1956 when mining began for shipment and captive use in US tile manufacture. This production has remained continuous and still essentially captive to the present. The Foxtrap deposit is currently the sole commercial source of pyrophyllite in Canada.

Jan 1, 1994

By Spencer R. Titley

"For his pioneering contributions to the understanding of the geology of porphyry copper systems" Recipient Of The 1997 D. C. Jackling Award SPENCER R. TITLEY Introduction The subject of this lecture, a late century perspective on porphyry copper geology, is one of current interest and importance as the search for these ores remains intense. It is presented in the belief that an appreciation of our present understanding of the subject requires it to be viewed historically, thus providing a basis for evaluating appropriate directions for continued study. At the outset, it is important to note that the technology of mining and extractive metallurgy has developed ore from these low grade orebodies, starting with D. C. Jackling, and has continued to create them as copper grade and price have diminished. But the continued search for them is a geological problem that responds to growing expectations of people and societies; exploration based upon ever increasing knowledge of the habits of the ores has been very successful. This is the story of evolution of geological thought and practice in porphyry ore search across an interval of time beginning with the bulk mining of "low grade" copper ores at Bingham and ending with late Century concepts. "How did we get here?" The lecture concerns the ideas of many different people. The ideas and events discussed reflect a bias on North American thought, where the great low grade orebodies were first recognized as such and where many of the basic geological ideas were developed. A very great number of geologists have contributed to this understanding. In no sense is it meant to minimize the contributions to the story that have evolved in the study and mining of ores of the Andes, whose development and expansion has been nearly synchronous with that in North America - nor to minimized comparable contributions made in the late century from studies of the newer discoveries of deposits in other regions, especially the southwestern Pacific regions. In expansion of this topic, I have found that many important concepts are marked by appropriate publication but some are not, or I have not been able to discover documentation. Many notions appear to have become conventional knowledge without publication, mostly being geological viewpoints developed synchronously from similar observation. Thus, apologies are extended in advance to those whose work I have might have missed and to those unknown to me whose unpublished ideas may have seeped into the pool of common knowledge without appropriate recognition. The analysis here addresses events of two time segments, an older one extending from the developments at Bingham in the early 1900s through the Second World War, ending about 1950: the second period extends from that time to the present. This separation is seen in Figure 1, which traces numbers of publications through the period as extracted from some 700 publications, again with a North American bias, from an annotated bibliography of porphyry copper geology in preparation. During the early period, exploration was "immature" in North America, that is, geologists looked for new districts and sites of the deposits. Outcrops were sought that carried the signatures of former mineralization and regional controls related to structural geology were closely studied. In the later period, North American exploration had "matured" into a study of districts, rather than a search for them. As the studies of these ores intensified during the younger period concommitant with increasing demands for the metal, they did so with a broadened understanding of some habits of occurrence, of hydrothermal alteration, mineral zoning, petrology, and geochemical and geophysical signatures. Outside of North America, search remained "immature" but closely related to the

Jan 1, 1998

By I. Yaniv

The magneto-hydrostatic method can be used today to separate slightly magnetic or non-magnetic particles according to differences in their specific gravities and magnetic susceptibilities. The classical approach is to effect stratification prior to separation. This paper discusses some of the significant parameters which bear on the design and pattern of the expected stratification in the separation cell. As the characteristics of the magnetic field, and consequently those of the magnetic forces, are determined by the geometry of the poles, this subject is treated first. In this context a new approach, whereby the range of stratification is extended, using positive as well as negative gradients, is presented. Finally, the effect of the relative size and shape of the particles on stratification is discussed.

Jan 1, 1978

By B. M. McKay

The Walnut Creek Mine was developed in 1989 to supply lignite to the Texas-New Mexico Power TNP-ONE power plant. Being new, we had the opportunity to start from scratch and rethink many of the traditional methods of managing a mine operation. We had the opportunity to create a team environment, encouraging people to get involved and make decisions. The founding philosophy of the mine, "A Quality Product by Quality People", acknowledged that the key to a productive, quality operation was the people. This paper will explore methods employed by Walnut Creek in selection of team members, building the team and the relative success of these methods.

Jan 1, 1993

By F. J. Murrell

No other region of the world is enjoying the tremendous growth of power use that is currently being experienced in Asia. Fortunately for those of us in the coal industry -particularly in Asia -the preponderance of the power plants being planned or under construction designed to use coal as the power plant fuel. This has produced a significant increase in the demand for steam coal, which has in turn encouraged many of us in the industry to develop new coal mines. One country that has enjoyed very substantial growth in coal production is Indonesia. This developing country of 195,000,000 people who live on the nearly 13,000 islands of Indonesia have emerged very quickly to become the third largest exporter of steam coal, following only Australia and South Africa. Almost all coal in Indonesia is mined by surface mining methods. This paper will examine the surface mining of coal in Indonesia, as it continues to be an important part of the supply equation for coal in Asia.

Jan 1, 1996

By Suresh P. Babu, Joseph W. Leonard, Richard Muter, D. P. Sen

OUTLOOK FOR COAL UTILIZATION In 1975, about 650 million tons of bituminous coal and lignite mined in the United States was used to meet 55% of the primary energy input for electric power generation and 26% of the total industrial consumption.1 Even though this amounts to only 21% of the total energy requirements, it is believed that with the declining natural gas resources and uncertainty of liquid fuel imports, coal will assume a more dominant role in suppplying our future energy needs. A regional breakdown of the coal reserves of the United States along with their characteristics is shown in Table I. At present the United Stares Energy Research and Development Administration (ERDA) and the US Bureau of Mines (USBM) are financing extensive research programs in advanced mining methods and energy conversion processes. The increased demand for wal which may result from these research programs may also create large-scale environmental protection problems. As more and more coal is mined the production of undesirable coal fines and dust also increases proportionally. The USBM and the Environmental Protection Agency (EPA) research in this field includes development in the areas of instrumentation for qualitative and quantitative analysis of wal dust, protective devices, and dust collectors. Dust control by water sprays, steam, and foam are also being investigated. Other aspects of safety in mining include developing methane drainage techniques prior to coal mining, fire and explosion prevention, and neutralization and disposal of acid mine waters. It is the belief of coal technologists that when the emphasis shifts to coal as the primary source of energy. the existing methods of mining and preparation of coal must be improved considerably to supply large quantities of quality coal for energy conversion. It is the objective of the present large-scale research financed by ERDA to produce substitute fuels from coal. Large-scale gasification pilot plants are being constructed by Bituminous Coal Research, Consolidation Coal Co., Institute of Gas Technology, and the Pittsburgh Energy Research Center to produce coal gas of natural gas standards at 1,000 psig. The processes being adopted by these pilot plants are oriented towards recovering most of the sulfur from coal by absorbing H2S and its subsequent conversion to elemental sulfur. The environmental protection standards will be strictly followed in using the results of these pilot plants to construct large-scale coal gasification plants in the latter part of the 1970's. With the increasing awareness of the need for air pollution control, considerable research is being done to minimize sulfur dioxide emission from thermal power plants. Utilization of limestone and dolomite scrubbing systems and caustic treatment of stack gases have proved to reduce sulfur and nitric oxide emissions by about 90 to 96%.3 Currently, about 22 scrubbers are in use in the United States to reduce sulfur in stack gas emission. In the long-term, it appears that optimal combinations will be developed involving both advanced coal preparation technology and wet scrubbing. The sulfur compounds are converted either to elemental sulfur of sulfuric acid. Besides the sulfur compounds, the major byproduct of the coal utilization industry is the large amount of coal ash. The Coal Research Bureau at West Virginia University has developed a practical use for coal ash as a structural material. The coal industry will undergo revolutionary changes when coal becomes the primary source of energy. New coal mining and preparation processes will be introduced to meet the ever-increasing per capita energy requirements. 2. BENEFICATION Introduction Coal preparation, like the beneficiation of ores, is also aimed at the separation of values from associated waste. Even though the unit operations involved when enriching ores and coal are similar, there are certain characteristics unique to coal preparation. Unlike the scattered and concentrated veins of underground minera1 ores, coal is distributed uniformly and very much in abundance in the coal mines. Coal occurs as the metamorphosed sedimentary deposits of vegetable matter, while metal and mineral deposits occur in great varieties of forms, structures, and origin-from igneous to sedimentary and metamorphic. The mined coal, being much more friable than mineral ores, is subjected to less intensive size reduction operations. Ores are usually ground to a very fine size for subsequent concentration, while coal is crushed to a coarser size, since considerably less liberation is needed to achieve the desired degree of separation. Since mineral matter is to a great extent discretely distributed in coal, concentration is mainly achieved by taking advantage of differences in specific gravity between clean coal and associated waste. In general, about 90% of coal is concentrated using specific gravity separation and about 10% by froth flotation. In contrast, these operations are frequently reversed in the beneficiation of ores. In coal preparation almost all fractions separated during various stages are made use of. while large amounts of gangue material are rejected in the concentration of ores. Hence, coal generally has a much lower ratio of concentration than ores. Since ore deposits are frequently more variable and mineralogically complex than coal, beneficiation of ore may require more plant flexibility and point-to-point quality control. This characteristic difference between the mineral ores and coal is attributed to the generally used one-step processing in coal as compared to the multiple-step processing of ores. Dewatering to enhance the energy content of coal is usually considered a major unit operation. Even though thickening and filtration are common for dewatering ore concentrates and cleaned coal, vibrating centrifuges and disk filters find unique application in the coal industry for achieving these types of solid-fluid separation. In coal preparation, thermal drying is carried out in separate units at the mine. While ore concentrates are usually dried at the smelter. Although the drying of ores is seldom considered dangerous, volatile matter and combustible dust are reasons why the thermal drying of coal can be hazardous. Open air storage of ores and mined coal results in partial oxidation. Unlike the oxidation of ores, the oxidation of the pyritic and carbonaceous constituents of coal together with the heat of condensation of moisture contribute to spontaneous heating and the subsequent combustion of coal in storage. Among the other significant difference between concentration of ores and coal are the weight and capacity of processing equipment. Coal processing employs less cumbersome, higher capacity units while the beneficiation of ores usually requires much more massive and frequently lower capacity equipment. Properties of Coal Which Influence Design The widely varying and heterogeneous composition of coal, due to metamorphism, determines the preparation design and uses of the resulting products. Petrography serves as a useful system of classification to identify the coal types present and their distribution. Early

Jan 1, 1985

By Harry Perry

A technology for producing liquid fuels from oil shale at prices competitive with crude oil prices is a necessary but not exclusive prerequisite for the development of a shale oil industry. Many other factors will affect the timing and the rate at which oil shale is commercially developed. Among the more important are: governmental policy concerning oil shale and oil resources (including the Outer Continental Shelf) that are under Federal control; oil import policy; Federal taxation of shale oil production including depletion allowances; regulatory practices; competition from other energy sources, both synthetic and natural; Federal treatment of factors affecting competing energy resources; and present legislation under which the public resources must be leased. Significant changes in any of the foregoing factors could have a controlling effect on the timing and rate of oil shale development. The effect of changes in each of these factors is evaluated.

Jan 1, 1969

By S. Gundiah

Preparation of functionalized polymers from the polymerization of monomers and preformed polymers are discussed with a few illustrative examples. The methods of their characterization, with reference to their application in flocculation, are described.

Jan 1, 1987

By J. W. Merks

At mineral processing plants the accuracy and precision characteristics of assays in mill feed, tailings and concentrate largely determine the reliability of the metallurgical balance. The accuracy of measurements is ensured by selecting effective sampling methods and efficient sample preparation procedures, and by effecting each phase without introducing a systematic error while the precision of measurements is determined by the sampling regime. Sampling systems and components, sampling methods and regimes, and sample preparation procedures will be reviewed. Different techniques to determine variance components for sampling, preparation and analysis, and to detect systematic errors in assays at mineral processing plants, will be discussed.

Jan 1, 1986

By Reed S. C. Rogers

The breakage parameters of phosphate ore were determined by batch first-order grinding studies in a laboratory ball mill according to the procedures described in the text by Austin, Klimpel and Luckie, using a slurry density of 70 weight percent. The results were scaled to five larger mills of 0.56 m diameter by 0.91 m length (2 ft. by 3 ft.), 0.82 m by 1.52 m (3 ft. by 5 ft.), 3.36 m by 7.90 m (11.5 ft. by 25 ft.), 4.41 m by 9.10 m (14.5 ft. by 30 ft.), and 5 m by 11.1 m (17 ft. by 36 ft.), assuming equilibrium ball charges for the full-scale mills. The results were used to predict product size distribustions and capacities for batch grinding in the 0.56 m and 0.82 m diameter mills and open circuit grinding in the 0.82 m diameter and larger mills using a one-large/two-small reactors in series model fitted to the residence time distribution measured in the 4.41 m diameter mill. The simulated results were compared to plant data for ranges of mill capacities. It was found that the simulated product size distributions were in good agreement with the experimental values below the 70% passing sizes, but did not agree so well in the top sizes. The predicted capacities were in approximate agreement with experimental values for the pilot-scale mills, were about 7 percent too high for the 3.36 m and 4.41 m diameter mills and about 25 percent high for the 5 m diameter mill. Use of the Bond method with the measured Work Index of the phosphate ore gave capacity predictions that were 45 to 150 percent too high.

Jan 1, 1985

By I. Melik-Gaykazov, N. N. Melnikov, V. A. Fokin, S. P. Reshetnyak

Kola Mining Institute has been carrying out investigations of the possibility to steepen the walls of the Kovdor open pit with the design depth of 600 m. Steeping (up to 60°) wall angles is done by double height (24 and 30 m) benches with vertical slopes. One of the safety factors of mining with such walls is choosing the width of the safety berms preventing against rock falling from the slopes into the pit working area. The test on rock falling from 24 m benches has shown that vertical slopes are not more dangerous compared to the inclined(60-75°) ones.

Jan 1, 2003

By R. E. Hochscheid

Cyclones installed in three closed- circuit grinding systems were changed from conventional, vertical mounting to horizontal mounting with a favorable improvement in classification efficiency. In two of the installations, apex plugging problems were eliminated because horizontal mounting permit- ted the use of much larger apex orifices. Marked reduction in circulating load was accompanied by greatly reduced maintenance requirements for the cyclone and the cyclone feed pump in one of the installations.

Jan 1, 1988

By R. A. Metz, M. A. Bryant, J. C. Goodwin, T. B. Faddies, L. D. Kornze

The Mercur Gold Mine is located 56 km (35 air miles) southwest of Salt Lake City in north central Utah. In July 1981 Getty Mining Company made the decision to put Mercur into production. The first gold bar was poured in April 1983. This paper provides details on: 1) the history of the camp, 2) past production, 3) geology of the deposit, 4) the exploration and development program, 5) ore reserve estimates, 6) detailed geologic pit mapping, 7) production blasthole sampling techniques and 8) the use of geostatistics (kriging) in handling assays and gold extractions to produce the required mill feed.

Jan 1, 1992

By S. A. Allison, N. P. Finkelstein

After a brief consideration of the properties of zinc sulfide minerals, their flotation characteristics, and their reactions with thiol collectors, the literature on the activation of the minerals by cupric ion, their deactivation by cyanide, and their depression is reviewed in detail. The distinction between deactivation and depression is stressed. The contradictions in the published results and theories are discussed and attempts are made to resolve them. It is concluded that, whereas all aspects of the subject require further investigation, the study of depression is most likely to yield benefits in practice.

Jan 1, 1976

By D. R. Kalasky, J. M. Mutmansky, B. Kolonja

This paper considers simulation of truck dispatching systems using maximum expected production of the truck-shovel system as the measure of performance. Two analysis methods are utilized: multiple comparisons with the best (MCB) and the combination of MCB with the variance reduction technique known as common random numbers (CRN). These two techniques are compared via simulation experiments. Results show that the combined procedure of MCB with CRN is the superior tool to use to reduce the total number of replications needed to ensure the specified probability of correct selection from a number of systems. In this case study, MCB with CRN reduced the variance by 29% and the number of required replications by 48%. Also, the MCB with CRN procedure narrowed the confidence interval by 18%.

Jan 1, 1995

By Fang-tu Wei

The purpose of developing this system is to monitor the operating status of the fully mechanized mining system in order to raise it's reliability. The completely mechanized coal mining system is a complex dynamic system, involving many sub-systems. It is the key of the mining process as well as a connected system composed of each working procedure. Any hitch in breaking, loading or transporting will interrupt the mining process. The analyses of the operating data has proved that the reasons causing the interruption of the extracting processes mainly come from the inner of coal face. Hence, after the installation of the MINOS system in England, the delays of belt conveyor sub-system were reduced. But the production increment was not as much as expected.

Jan 1, 1986

By C. J. Bise

Continuous mining accounts for about 69% of the nation's underground coal production. This level is not expected to change much in the near future. This is because continuous mining represents the primary means of under- ground coal production. It is also the primary means of driving development entries for underground coal mines, including longwall mines. The continuous miner worksite contains many characteristics that can lead to personnel accidents. It continues to be an area of concern for mine managers, safety engineers, and training coordinators. In an effort to assist mine management in attempts to reduce the number of accidents and injuries sustained in this area, this paper presents a loss-control-based, non-intrusive strategy for conducting safety evaluations at continuous miner worksites.

Jan 1, 1991

By E. K. H. Goh

A reliability-based engineering design approach for the effective design of reshaped spoil dumps was developed with the aim of obtaining structurally reliable spoil dumps at optimum reshaping costs. The aim was also to satisfy environmental erosion standards and community expectations. This approach encompasses the linking up of three major components: erosion appraisal of spoil dump designs, reliability-based engineering design of spoil dumps and costing of spoil dump reshaping practices. This paper addresses the application of the reliability-based engineering- design approach to the assessment of spoil dump designs for erosion control. Included are various types of erosion prediction models and reliability-based engineering-design analytical techniques. Also included is a case study that demonstrates the application of this approach.

Jan 1, 2000

By Ronald G. Schmidt

AND SOME RIN UP HILL AND DOWN DALE, KNAPPING THE CHUCKY STANES TO PIECES WI' HAMMERS, LIKE SAE MANY ROAD MAKERS RUN DAFT. THEY SAY IT IS TO SEE HOW THE WARLD WAS MADE. Sir Walter Scott St. Ronan's Well - 1824 In the minds of many, geologic exploration has advanced little since the early nineteenth century. In truth, despite the development and refinement of new and potentially valuable technological tools, the approach or philosophy of the explorationist has received meager attention in professional literature. In many areas, the explorationist relies upon experience, subjective judgement and general intangible inspiration, often traveling together under the misleading pseudonym of "art," in achieving both an exploration plan and in making the myriad day to day decisions necessary to the execution of that plan. Without a solid, objective basis for decisions, exploration under this concept is little more than guesswork largely by intuition, and it is small wonder that many exploration programs flounder in a sea of over-expenditure inefficiency or fail to fulfill their expected goals within the funding which has been provided. From a rational management point of view, such a state of affairs is frustrating and inconsistent with the application of the same scientific principles which are presumed to be the basis for the exploration methods which are used. This somewhat presumptuous point of view cannot be extended as a general condemnation of the many exploration programs which are both technically and economically successful. On the other hand, the

Jan 1, 1968