Search Documents

By Z. Jin, D. DePaoli, P. Zhang

"Phosphogypsum is a byproduct created during the production of industrial wet-process phosphoric acid. This study focused on recovering rare earth elements (REEs) from a Florida phosphogypsum sample and investigated the effects of removing detrimental impurities such as phosphorus pentoxide (P2O5 ), uranium (U) and fluorine (F) during the leaching process. Experimental results indicated that REE leaching efficiency increased rapidly, reached a maximum and then began to decrease with sulfuric acid concentrations ranging from 0 to 10 percent and temperatures ranging from 20 to 70 °C. At a sulfuric acid concentration of 5 percent and leaching temperature of 50 °C, REE leaching efficiency obtained a maximum value of approximately 43 percent. Increasing the leaching time or liquid/solid ratio increased the leaching efficiency. The leaching efficiencies of P2O5, U and F consistently increased with sulfuric acid concentration, temperature, leaching time and liquid/solid ratio within the testing ranges. A fine-grain gypsum concentrate, sized smaller than 40 µm, was separated from leached phosphogypsum through elutriation, in which the P2O5, U and F content levels were reduced by 99, 70 and 83 percent, respectively, from their content levels in fresh phosphogypsum. IntroductionPhosphogypsum is a byproduct generated during the industrial wet process of phosphoric acid production, in which sulfuric acid is used to digest phosphate rock. Gypsum (CaSO4·2H2O), the main component of phosphogypsum, usually accounts for 65 to 95 percent of phosphogypsum by weight.There are small quantities of impurities in phosphogypsum, such as phosphates (H3PO4, Ca(H2PO4)2·H2O, CaHPO4·2H2O and Ca3(PO4)2), fluorides (NaF, Na2SiF6, Na3AlF6, Na3FeF6 and CaF), sulfates, trace metals and radioactive elements (Rutherford, Dudas and Arocena, 1996). Global phosphogypsum generation is estimated at 200 Mt/a (Parreira, Kobayashi and Silvestre, 2003; Yang et al., 2009), but only about 15 percent is recycled as building materials, agricultural fertilizers or soil stabilization amendments (Tayibi Choura and Lopez, 2009)."

Jan 1, 2017

By Joseph K. Cavey

To accommodate the new Pier A expansion at BWI airport, a 1.8 m (6.0 ft)diameter stormwater pipe was constructed below active Runway 15R-33L. The jacked tunnel alignment runs east/west below the runway, and the depth the crown was 6.1 m(20 ft). Soil conditions consisted of very loose to medium sand and gravel, with some medium stiff clay and silt. Super Jet Grouting was selected as the ground treatment system, creating large diameter columns. All work was performed from the surface of the runway between the hours of 12 am and 6 am. Monitoring points along the tunnel in the grout zone indicated zero settlement during tunneling. Tunneling operations in front of and beyond the treatment zone experienced significant settlement. Super Jet Grouting in the treatment zone provided a low permeability continuous stable soilcrete that was readily mined while the runway remained in service.

Jan 1, 2003

By Andrew M. Wala

The determination of air quantity needed to dilute the exhaust gases to a safe level has to be individually evaluated for particular cases. The diesel powered machines are doing some specific operations in the cyclic order required by the technical process. The dynamics of this process in certain conditions has an essential influence on environmental health conditions in the working area. The main purpose of this paper is to show, using computer simulation, how the movement (dynamic) of diesel vehicles effects environmental health standards and also how to determine the required air quantity for certain conditions

Jan 1, 1983

By Sam H. Patterson

The advances in knowledge of world bauxite resources in the last few decades include contributions to the geology of deposits, discovery of large resources, shifts in availability, and changes in. the industry in response to political and economic pressure. Improvements in the understanding of geology have resulted from the larger numbers of geologists working on bauxite and better exchanges of information. The large deposits discovered are mainly the laterite type in tropical regions. These discoveries have led to major increases in bauxite resource estimates as well as to shifts in bauxite availability and in the ranking of producing nations. Changes resulting from political, environmental, and economic pressures have resulted in increased costs of bauxite and in renewed interest in potential nonbauxite sources of aluminum. Aluminum is produced from nonbauxite raw materials only in the U.S.S.R.; however, research on extraction processes or investigations of nonbauxite alumina resources has taken place in several countries.

Jan 1, 1984

By C. Cigna, M. Patrucco, D. Savoca, E. Lovera

The paper deals with the activity program and the preliminary results of a research work commissioned by IReR Research Centre and Regione Lombardia to the Department of Land, Environment and Geotechnologies of Politecnico di Torino. The aim is to define measurement, analysis and control criteria for the emission of chemical and physical pollutants from non-metal mining industries, with particular reference to noise and airborne particulates. Such emissions are related to health risks and annoyance problems, both for the working crews and the neighbouring population, and so, in order to get an effective sustainability of the industry, suitable reduction methods and assessment tools are required. A simple technique for the evaluation and forecasting of both the emission levels and deriving impact has been tested at different mining and quarrying sites, considering their differences in terms of layout and exploitation method, the latter ascribed to a series of main typologies as present in Lombardia region.

Jan 1, 2005

By R. R. Beebe

Marcona Corporation produces about 3.5 million long tons of iron ore pellets annually on its two travelling grate pelletizing machines at San Nicolas, Peru. During 1969, these pellets will be shipped to customers in four marketing areas--Japan, the United States, Europe, and South America. All of these sales are on the open market, and product quality is a major concern. Typical chemical, structural, and quality test results for Marcona pellets are given in Table 1. [ ]

Jan 1, 1969

By Michael G. Nelson

Underground coal mining practice often requires that some coal be left in place at the seam boundaries after mining, for purposes of ground control, quality control, machine guidance, or good operating practice. Many methods for measuring the thickness of boundary coal have been developed, but only the natural % R gamma background method as bee used in routine operations. Use of this method is constrained by the level and consistency of the natural gamma background in the bordering strata, the accuracy of the gamma detection instrument, and the elevation profile of the seam boundary being detected. Computer simulations for three commercially available gamma detection instruments, designed for mine use, showed that measurement of boundary coal thickness by the natural gamma method can provide satisfactory input for horizon control systems when the gamma detector is large, when the sensor is mounted on the mining machine, and when the elevation profile of the seam boundary does not change rapidly in the direction of advance.

Jan 1, 1993

By F. Vincent, A. Boulet, M. Noaparast, F. Woodcock, A. R. Laplante

A novel methodology to estimate gold recovery by gravity is presented. It makes use of a population balance model which represents gold liberation, breakage and classification behaviour and applies pre-concentration and recovery data to gravity recoverable gold (GRG) to predict overall recovery. The methodology is designed for gravity circuits located in the circulating load of secondary grinding mills. Gold liberation is estimated by processing a sample of representative ore with a laboratory Knelson Concentrator (LKC) in three successive steps, each at a finer grind than the previous one. Breakage behaviour is represented by a matrix H, which redistributes GRG in the feed of the secondary mill in the various size classes of its discharge. Provision is also made to account for gold overgrinding, which decreases the overall amount of GRG. Classification, pre-concentration and recovery data are estimated from plant performance, and are represented by the diagonal matrices C, P and R. The methodology is demonstrated with case studies of greenfield, retrofit and optimization applications.

Jan 1, 1995

By Stephen W. Denton

Planning a mining operation in Alaska will involve the investigation of many parameters common to mine planning anywhere. However, there are some unique circumstances that must be recognized when one considers development of mining operations in Alaska. This paper will not attempt to provide a blueprint for mine planning in Alaska, but hopefully will provide a better understanding of the truly unique nature of the northern latitudes. Given this understanding, the mine planner can better assess the potential hurdles along the road to a successful mining operation. The regulatory trend towards uniform standards for mining throughout the United States exemplifies the necessity for Alaska to prove its unique position in the natural resources picture. The factors which make Alaska truly different from the "Lower 48" can be summarized by four points 1) Remoteness and Size 2) Seasonable Extremes 3) Geologic Immaturity 4) Vegetation and Wildlife

Jan 1, 1984

By III Cocanour

The line scan video photometer is a personal computer (PC) based, software-driven instrument which is used for the real time, on-line analysis of industrial process streams. The novelty of the instrument lies in the integration of its various components: (l) a true Red/Green/Blue (R/G/B) color video camera; (2) a unique, line-scan color sample and hold technique which provides a 4 to 20 mA analog signal to a commercial 12 bit analog to digital (A/D) converter; (3) software which converts data through a color absorbance algorithm to correlate elemental color to concentration; and (4) software-based control which utilizes color data, along with temperature and conductivity data to control process equipment. The photometer can be used for noninvasive analysis wherever color hues are representative of process variables such as chemical concentrations or mineralogy color reflectance. The line scan video photometer has been successfully demonstrated in solvent extraction/electrowinning (SX/EW) and ball mill circuits of copper producers.

Jan 1, 1996

By H. L. Bourne

This paper describes six basic stages between perception and production for a new sand and gravel deposit. Sand and gravel, like many of our natural resources, is taken for granted. It is assumed by John Q. Public that because sand and gravel is ubiquitous that it is available whenever and wherever needed - so long as it does not have to be mined in his neighborhood. This idea illustrates one of the enigmas of the industry, the fact that sand and gravel is abundant; however, its availability is another matter. Another problem is that this resource falls in the category of high volume, low profit materials; therefore, transportation costs are critical. Transportation roughly doubles the cost of these materials. It is not difficult to find sand and gravel, at least in Michigan. The problem is to locate a new source close to a market, near an adequate transport route (usually a highway) and in an area which will allow mining.

Jan 1, 1970

By Ivan Caetano Machado

Good morning ladies and gentleman. During 1995 Prof. R. P. King (University of Utah Comminution Center) presented 2 papers on new horizons in comminution: "Comminution Research in the United States " was presented at the 1995 Meeting of the National Mining Association, while "Comminution: Meeting the Needs of Fundamental Research in the Mineral Industry" was presented at the 2nd SME Research Forum - 1995. In both papers a very interesting graph named "Energy usage for various comminution schemes" illustrated some poignant issues proposed by Prof. King. We do think that some of Prof. King's ideas might very well serve as "warm-ups" for this Comminution Panel Discussion, which are ultimately the goals to be reached by the 3-minute presentations. Thus, we shall be addressing in the sequence Prof. King's most relevant ideas (as well as introducing his graph), intending therefore show how important creative and state-of-the-art Mill Modeling is, if it is to become a Tool to Effective Cost-Saving Optimization Strategies.

Jan 1, 1996

By Robert S. Hendricks

The paper describes the design and operation of a Shaft Boring Machine (SBM). The machine has been developed by The Robbins Company. It is anticipated that the prototype, which will bore shafts in the 6.1 to 7.3 m (20 to 24 ft) size range, will be placed in operation during 1985. This pioneering application of rapid excavation technology is expected to lead to significant improvements in the cost and speed of shaft construction. The technical and economic factors which have limited the employment of Shaft Drilling and which caused unsatisfactory results with earlier attempts at Shaft Boring are reviewed. The design criteria adapted to overcome these problems are discussed. Cost and performance estimates are presented and are compared to conventional sinking methods. Factors that influence the application of the SBM to specific projects are reviewed.

Jan 1, 1985

By M. S. Klima, B. K. Kim

The use of a 25.4-mm- (1-in.-) diam water-only hydro-cyclone for separating liberated 125 x 25- µm high-density particles from similar-size lower-density (2.65 g/cc quartz particles, as might be used in soil washing applications, was investigated. As expected, cyclone performance was greatly affected by changes in cyclone geometry and operating conditions. A single-stage separation recovered 75% of the magnetite (4.8 g/cc) while rejecting nearly 60% of the quartz. With ferrosilicon (7.0 g/cc) as the heavy component, the recovery improved to 85%. The use of dense medium in a single stage increased both ferrosilicon recovery and quartz rejection to approximately 90% each. In addition, computer simulations of a three-stage circuit were performed. The simulations showed that recoveries approaching 97% with quartz rejections of 95% were possible.

Jan 1, 1999

By David Atkin

This paper presents methods and results of environmental planning conducted for a proposed coal and iron ore transshipment terminal which would be located on reclaimed land west of Lisbon, Portugal. Oceanographic, navigational, marine, structural, material handling, and financial studies of the terminal were conducted along with the environmental analyses. However, because of the proximity of the terminal to heavily used recreational resources, residential areas, and biologically valuable habitat, anticipating and reducing the environmental effects of the terminal to minimum levels was a very important part of the overall project. The results of the study indicate that even the impacts associated with worst-case conditions would be acceptable because of appropriate pollution control measures and planning.

Jan 1, 1983

By B. Das

Most coals are susceptible to spontaneous heating which in turn creates problem to mining, storage and transportation of coal. It is impossible in actual practice o eliminate spontaneous heating but spontaneous combustion can effecively be controlled through a clear understanding of its mechanism and the factors affecting it. There are altogether six stages in the process of spontaneous combustion. This includes the water adsorption stage and six oxidation stages: chemi-sorption (upto 70°C), decomposition of peroxygens (70°C-150°C), oxy-coal formation (150°C-230°C), combustion initiation (230°C) and active combustion (> 230°C). Heat is produced in all these stages. On the other hand heat is also dissipated so that some equilibrium temperature is reached. If this temperature exceeds a certain critical value (generally about 70°C), coal oxidation may advance to spontaneous combustion. The major factors influencing spontaneous combustion of coal are: coal rank, maceral composition,, water, mineral matter, joints and fissures, seam depth and thickness, mine Layout, method of ventilation, etc. Susceptibility is high for low rank coals and generally decreases with increase in rank. Of the macerals, the exinites are generally most susceptible, the inertinites least and the vitrinites somewhere in between. Water plays a major role on the spontaneous heating of coal, assisting in someways and inhibiting in other. Unrecovered coal in the gob (generally in thick seams) is a major source of fire hazards and this is specially important in shallow mine. Proper design of mine ventilation system can substantially reduce the risk of mine fire. Panel layout and load transfer can affect the development of induced cracks which in turn influence spontaneous heating. Finally, the difference between the spontaneous heating of coal in a seam and that in storage or transportation is mainly due to the change in moistured content, air circulation through the coal and coal fragmentation. These aspects have been analyzed in this paper with a view o reducing the risk of spontaneous combustion.

Jan 1, 1986

By Ke Yang, Kai Zhang, Xiaolou Chi, Xiangyang Zhang, Yingming Li

Based on the research background of 1303 working face return air roadway in Jinyuan Zhaoxian Mine, Shaanxi Province, a method of determining the reasonable spacing of boreholes is proposed based on the stress transfer degree of coal above and between boreholes, combined with the law of plastic zone and energy evolution by theoretical analysis and numerical simulation. After drilling pressure relief, the average daily energy of microseismic events decreased by 70%, and those with microseismic energy greater than 104 J decreased by 99.2%. The research has a strong guiding significance and research value for determining the reasonable distance of borehole pressure relief.

Jun 25, 2024

By D. Malhotra

Metallurgists are continuously striving to improve recovery. But optimization of profits and/or revenue dictates that recovery can be sacrificed at the expense of throughput. However, recently there has been significant interest in the concept of retreatment of tailings to enhance recovery and hence revenue while maintaining high throughput. The authors discuss the technical and economic factors that need to be considered in evaluation of the feasibility of retreatment of tailings including the potential feed streams (i.e., rougher tailings, cleaner tailings, etc.) and processing options (i.e., physical beneficiation, chemical processing, etc.). A case study for base metals is discussed.

Jan 1, 1994

By F. W. Brackebusch

A unique machine has been designed for mining narrow veins. The machine, called the NONN, walks on the walls of the stope and carries a boom-mounted hydraulic impact breaker. The concept of walking on the walls allows an existing muck handling system such as LHDs to operate beneath the NOMN. The NOMM has four sets of legs which can be manipulated independently or concurrently to cause the carrier to walk in any direction and to turn sharp corners. The mining rate using the breasting method is targeted to be 25 t/hr.

Jan 1, 1990

The purpose of this paper is to present validation studies of the mine-fire simulator using data gathered from an actual mine fire which occurred in November 1991 at the Pattiki Mine. To develop the model of the ventilation system with the fire in this validation study, the following adjustments were made: (1) flow and gas distribution in the entire ventilation network, and (2) fire parameters matching the data recorded by the monitoring system. After close correlations between simulation and real data were achieved, additional analysis of the ventilation system with the mine fire was performed. Presented and discussed in this paper are the following stages of the fire at the Pattiki Mine: (1) early fire (before the fire was detected), (2) preparation for and fire fighting with water, (3) fire sealing, and (4) fire extinguishing. This study evaluates the suitability of the computer software package for modeling underground fires. The paper also discusses the importance of the on-line monitoring system for the validation process.

Jan 1, 1995