Search Documents

The Gosowong epithermal quartz-adularia vein, in the Halmahera magmatic arc, is a new discovery in an area of primary tropical rain forest with no history of gold mining or mineralization. The newly recognized mineral district also contains a number of other epithermal vein systems, two centres of porphyry Cu-Au mineralization, and a number of argillic and advanced argillic alteration zones that may be related to underlying mineralization. Gosowong was discovered and tested through the application of basic exploration techniques including drainage sampling, soil sampling, trenching, magnetics, IP, and diamond drilling. Lapse time from the initial reconnaissance discovery of a stream sediment anomaly to the release of inferred resource estimates of approximately 1.0m ounces was just over 3 years.

Jan 1, 1997

By J. A. Halt, E. Larsen

"The Sydvaranger magnetite mine closed in 1996 due to low iron ore prices and was reopened in 2009. The flowsheet has remained more or less as in the old plant, based upon two grinding steps followed by magnetic separation. The magnetite is free of harmful elements and should be attractive on the high quality market. This requires a concentrate containing less than 2% SiO2, which previously was achieved by amine flotation. Amine was preferred because it could be used with sea water. The use of amine is now restricted by the Norwegian Climate and Pollution Agency. Therefore, testwork to replace cationic with anionic flotation was done. Activation of quartz with Ca or Mg ions prior to anionic flotation was shown by research from 1960 to 1980 to be effective under laboratory conditions. The old research results have been followed up in order to make a commercial process for Sydvaranger. Calcium activation works excellently with all Sydvaranger ores, including the ones containing amphibole minerals, but Ca activation requires the high and not environmentally friendly pH of 12.4. Magnesium activation at pH 10.5 is a little more challenging, because the maximum concentration of MgOH+ is about 100 times lower than that of CaOH+. Fortunately, the major impurity in the main Bjornevatn orebody is quartz, which responds well to Mg activation. The process does not appear to depend much upon water quality, as the silicates may already be activated during grinding and magnetic separation in recycled water. The new process is environmentally friendly, as only well-known household reagents are used; oleic acid or tall oil, dextrin, sodium hydroxide and magnesium chloride at pH 10.5.IntroductionThe processing plant of Sydvaranger Gruve AS (SVG) is located in the port town of Kirkenes in the northernmost part of Norway, 10 km by rail from the high-grade deposit of Bjornevatn. This plant has been able to beneficiate magnetite ore to up to 99.5% purity, as described by Sandvik and Malvik (2001). Using the magnetic properties of the ore and making the most out of its enviable liberation characteristics, the original plant consisted of ball mills and 600-mm magnetic separators. The plant was shut down due to market conditions in 1996 but reopened in 2009."

Jan 1, 2015

By D. Kumar, R. J. Sweigard, J. Silva

The Forestry Reclamation Approach (FRA) recommends that the upper 1.22 m (4 ft) of spoil material on reclaimed surfaces should be left as uncompacted as possible to facilitate efficient tree root growth. However, the main concerns about applying the FRA to steep slopes is that the upper 1.22 m (4 ft) of loose spoil material could cause instability. Successful application of the FRA on the flat and rolling surfaces precipitated this investigation. Details of a field investigation conducted at a steep-slope mine site are available in an earlier publication (Kumar and Sweigard, 2011). A total of 70 survey monuments were driven into the slope in a regular pattern to monitor any type of slope movement. Quarterly surveying of the monuments were done to quantify slope movement, either horizontally or vertically. The methodology developed in this research for field slope movement monitoring was validated using computer model results. Analytical models based on the limit equilibrium method (LEM) and numerical models based on the finite element method (FEM) were developed for slope stability analysis. The LEM analysis was done using the Geo-Slope/W program following the simplified Bishop method. However, numerical models were developed using the PLAXIS computer program following the Mohr’s Coulomb failure criterion and strength reduction technique. The slope stability analysis was performed for two different scenarios: first with the top 1.22 m (4 ft) of loose graded spoil material and second without top loose graded spoil material. Finally, the field investigation results were compared with stability analysis results. Both of these approaches showed that application of the FRA on steep slopes is not causing any significant instability problems, due to 1.22 m (4 ft) loose graded spoil that would not exist otherwise for overly steepened slopes.

Jan 1, 2013

By V. K. Karra

An improvement in the present day screen sizing methods calls for knowledge on i) how material in the size range: 0.5 x 1.5 times the through-fall opening of the mesh on a deck, splits between the oversize and undersize streams of the deck, and ii) how near-mesh content of the feed affects the screening performance. In the throughput based sizing method given here, this is accomplished through the introduction of a generalized partition curve and a near-mesh factor. A newly developed efficiency factor is employed in addition to the traditional screen sizing factors.

Jan 1, 1979

By F. J. Sotillo

Mineral processing requires good classification of particles to attain an adequate separation of minerals. This is of utmost importance in the case of sulfide minerals. An ideal classification is obtained when particles are separated at a given mesh, which is fixed according to the characteristics of each sulfide ore. Under these ideal conditions, particles coarser than the mesh of separation are recovered in the underflow, whereas particles finer than the mesh of separation are recovered in the overflow. This paper presents the results of pilot plant tests that were performed on Ag-Pb-Zn and on Ag-Au Peruvian sulfide ores using a Density Separator, and the comparison of these results with those obtained using hydrocyclones, under similar operating conditions. The results show that the ratio of circulating load is reduced by 50% by using a Density Separator with respect to that obtained by using hydrocyclones. Moreover, the effect of the improvement in the separation efficiency obtained by using the Density Separator on the kinetics of flotation is also shown. Silver recovery of the Ag-Pb-Zn ore increased by 18% whereas gold grade in the concentrate of the Ag-Au ore is doubled.

Jan 1, 1998

By D. J. A. Chambers, J. M. Wempen, K. D. Koper, M. K. McCarter, K. L. Pankow

"The EarthScope Transportable Array (TA) of broadband seismometers (www.usarray.org) was deployed across southwest Wyoming from November 2007 through May 2009. During this time period the Array Network Facility (ANF, anf.ucsd.edu) detected and located a total of six seismic events near the trona-mining district. This lack of seismicity is atypical compared to coal mines employing similar mining methods. In this study, eighteen months of continuous seismic data from several nearby TA stations are reexamined using conventional and correlation-based methods to detect seismic events. Waveform cluster analysis and epicentral locations are used to discriminate between mining induced seismicity (MIS) and seismic energy generated from surface blasts at nearby coal mines. The locations and magnitudes of the 143 newly detected MIS events are compared to regional subsidence as measured by Differential Interferometric Synthetic Aperture Radar (DInSAR). INTRODUCTION An abundance of natural resources and a favorable political climate have made southwest Wyoming home to multiple large mining operations. Among these operations are five underground trona mines located approximately 50 km west of Rock Springs, Wyoming. The trona mines employ room and pillar, longwall, and solution mining methods over an area roughly 900 km2, and produce a sizable portion of the world’s soda ash (Brown 1995). Historically, in the Rock Springs mining district, several relatively large magnitude seismic events have occurred. These events are thought to have been related to mining activity and have caused notable subsidence (Case 1997). The largest event in the region recorded by seismometers, ML 5.1, has been confirmed as the 1995 Solvay Trona Mine collapse (Pechmann et al. 1995). In addition, blasting at surface coal mines near Rock Springs produces significant amounts of seismicity; approximately 50% of all daytime seismic events in the Mountain time zone from 2007 to 2009 locate near an active surface mine in this region (Astiz et al. 2014). Much of the current research related to surface subsidence and induced seismicity focuses on wastewater impoundment (Ellsworth 2013) and hydraulic fracturing. The observable seismicity in geological injection environments is widely variable and McGarr (2014) has argued that, in such environments, the maximum amount of seismic energy that can be released is proportional to the injected volumes. Like injection environments, in extraction (mining) environments seismicity is highly variable depending on many geological and operational variables (Boltz et al. 2012; Carnec and Delacourt 2000; Fritschen 2010; Iannacchione et al. 2005; Sen 2013) and does not always correlate well spatially with subsidence, a surface expression of extraction at depth."

Jan 1, 2015

By J. E. Brownhill

This paper does not deal with the typical start-up issues of equipment, production capacity or work force. This is a description of the challenges faced and the changes made by the project team to bring to fruition the reconstruction of Port Inland. Many honored traditions and norms had to be overturned to find the winning combination that provided the productivity, flexibility and cost necessary to survive in today's competitive minerals environment. This paper covers the innovation in terms of machinery, operations, and management philosophy that permitted the renovation and reopening of Port Inland as a commercial limestone producer in the spring of 1992. Port Inland, constructed by Inland Steel in 1930, operated as a captive source of metallurgical grade limestone for the steel industry until its closure in 1989. Located in the Upper Peninsula of Michigan on the north edge of Lake Michigan, the operations consist of a deep water port facility with crushing, screening and stockpile storage for 500,000 tons of finished product at the port. Ninety-nine percent of the stone is shipped via lake boat to ports within the Great Lakes. The operation is unique in that both metallurgical Dolomite and Limestone are produced on site. In 1930, Port Inland was at the fore front of technological advancement. It was the first major mining operation to use roller bearings and other equipment innovations. Over the 60 years of operation, Inland Steel placed emphasis on steel making technology and iron ore mining at the detriment of the limestone operation. By the early 80's, Port Inland was no longer a leading competitor. Inland Steel, unable or unwilling to spend the capital to modernize, closed the facility in the fall of 1989.

Jan 1, 1994

By C. Maltesh

Anionic conditioning of phosphate ores prior to fatty acid flotation is a very critical step that determines the eventual selectivity, recovery and hence the economics of the process. However the chemical mechanisms operating during this conditioning step are not established. Several studies have been conducted in the past to determine the mode of interaction of collectors with the phosphate fractions however these have been done on a laboratory scale using pure phosphate minerals. In order to test the relevance of the observed effects to plant practice in this work a comprehensive survey of plant practice was first conducted and then adsorption on flotation feed and francolite were studied under simulated plant conditions. Effects of conditioning energy and water chemistry as well as solids loading and fuel oil were determined. Most importantly, different adsorption mechanisms were found to be dominant under laboratory and plant conditions. In plant water, there was some physisorption of oleic acid on phosphate flotation feed and francolite in addition to chemisorption. However, in distilled water under laboratory conditions only chemisorption was detected. Fuel oil reduced the residual oleic acid in solution after adsorption, which explains the beneficial role of extender in phosphate flotation. The dissolved species in solution arising from the flotation feed or plant processing water are shown to clearly play a major role in determining the adsorption of oleic acid on the substrates. The study also specifically demonstrates the importance of conducting research tests under plant mixing conditions and plant water chemistry for the results to be useful commercially.

Jan 1, 1996

By Yu-ren Jiang

Novel compounds of hydroxycarbamoyl carboxylic acids, including 2-hydroxycarbamoyl -3-methlcyclohexane carboxylic acid (HCMC), 2-hydroxycarbamoylmethyl decylen-4-yl carboxylic acid (HCDC) and 2-hydroxycar-bamoylmethyl tridecylen-4-yl carboxylic acid (HCTC) were synthesized. The flotation behaviors of diaspore, kaolinite and illite using these compounds as collectors were investigated. The flotation results revealed that the floatability of the minerals was, in descending order, diaspore and kaolinite, followed by illite, and the ability to collect the minerals was, in ascending order, HCMC and HCDC, followed by HCTC. At a dosage of 2×10-4 mol/L, both HCDC and HCTC show a strong ability to collect diaspore and a weak ability to float kaolinite and illite. The flotation recovery of diaspore is over 90% and that of kaolinite and illite less than 30%. Moreover, Fourier transform infrared spectroscopy (FTIR) spectrum and zeta potential, as well as the adsorption amount, indicated that the adsorption interaction between HCTC and diaspore was primarily a kind of chemisorption in the form of chelate rings, while the interaction between the collector and aluminosilicate mineral was dominated by physisorption. It was concluded that the novel hydroxycarbamoyl carboxylic acid compounds are highly selective collectors for the flotation of diaspore vs. aluminosilicate minerals.

Jan 1, 2011

By J. L. Parks

Designs, installation procedures, and performance characteristics of martensitic cast steel concaves are reviewed. Longer wear life, fewer pieces to install, and eliminating the need to scarf joints are the principal benefits of using martensitic steel to replace austenitic 12% Mn (Hadfield's) steel, the traditional concave material for large gyratory crushers. Installation procedures that reduce the risk of breakage are described. Operating practices that affect concave performance are also discussed.

Jan 1, 1992

By A. J. Neale

Much has been published lately about the application of advanced control strategies in the automatic control of autogenous and semi-autogenous grinding circuits. The application of adaptive control algorithms, self-tuning controllers, state estimation, and expert systems has been well documented. While these approaches can be very effective; experience has shown that quite often simply "fixing the fundamentals" can have a significant positive impact on overall grinding circuit performance. This paper will highlight the results of process optimization and process control work by the authors at a variety of autogenous and semi-autogenous installations. A review of one approach for quantifying the mill load/bearing pressure/power relationship is provided. Accurate monitoring of key mill process variables is a necessary prerequisite for both effective process analysis and process control. This paper discusses some of the concerns related to defining steady state operating conditions and the issues related to signal conditioning. The paper concludes with a discussion of an effective application of algorithmic constraint control which incorporates many of these considerations.

Jan 1, 1994

By W. J. Wuest

The U.S. Bureau of Mines (USBM) has recently developed a rock mass classification system for evaluating the structural competency of bedded roof strata; the Coal Mine Roof Rating, or CMRR. When compiled with the companion Lotus 1-2-3 spreadsheet, which is simple to learn and use, CMRR data are a useful tool with applications to longwall gate road pillar design, safety hazard mapping, and artificial roof support analysis. This paper demonstrates these applications under actual conditions found in current U.S. mining operations.

Jan 1, 1995

By M. du Plessis, J. P. Gouvea

Mesh based areal support is commonly applied in South-African deep-level gold mines. It forms part of an integrated support system that can cater for both rockfall and rockburst incidents. The application has been successfully applied over many years. Operations have different geotechnical conditions and practical considerations, which has led to the development of various types of mesh and integrated mesh-based support systems (i.e. meshing and lacing versus welded or chain-link mesh sheets). Typically rolls or sheets of mesh is pinned with rockbolts to the surface of an exposed excavation. Applications vary from hangingwall coverage in a conventional stope gully to complete excavation coverage in footwall drives of conventional mines or on-reef drives in massive mechanised mines. It is however critical to understand the behaviour of the rockmass and apply suitable support systems.

Apr 26, 2022

By J. S. Walstrom

Debate on an appropriate, acceptable method of regulating mine and mineral processing wastes has been ongoing since Congress passed the Resource Conservation and Recovery Act (RCRA) on October 21. 1976. Final regulatory determination on which mineral processing wastes are excluded from the RCRA hazardous waste regulations under the Bevill amendment was made by the U.S. Environmental Protection Agency on June 13, 1991. Regardless of whether a mining or mineral processing facility?s waste stream(s) lost or maintained its exclusion status under the Bevill amendment, that facility can expect more stringent regulation of affected waste streams. These more stringent regulations will be added to an already complex regulatory maze, which includes the Clean Air Act (CAA), Clean Water Act (CWA), Safe Drinking Water Act (SDWA), Comprehensive Environmental Response, Compensation and Liability Act (CERCLA), Superfund Amendments and Reauthorization Act (SARA), and Toxic Substances Control Act (TSCA), as well as state and municipal environmental regulations.

Jan 1, 1992

By Ulrich Maidl, Gustavo Aguiar, Argemiro Ferreira, Marco A. Peixoto Silva, Marc Comulada

"Metro Line 5 in Sao Paulo is being constructed. This lot extends for 4,940 m with twin EPB shield tunnels under a dense and busy urban area, with an excavation diameter of 6.9 m. The tunnels run predominantly in the tertiary soils of Sao Paulo where extensive experience exists from previous EPB shield tunnel projects. However, new experience is being gained in Sao Paulo in shield tunnelling through Saprolite, the weathered product of the underlying Gneiss crystalline basement, through the resulting residual soils and in rock-soil mixed face conditions. Furthermore, experiences in difficult mixed face soil conditions with overconsolidated clay at the face in combination with loose sands at the crown under the groundwater table will be presented. Additionally, the design, operational and controlling approach followed for the shield drive at particular critical cross-sections where the shields were driven close or under buildings. INTRODUCTION Within the framework of Sao Paulo´s metro network expansion, the excavation of the shield tunnels for Metro Sao Paulo Line 5 is currently taking place. The present paper deals with the description of the most relevant features from the construction of the Line 5 – Lot 3 tunnels. The paper presents how particular challenges were dealt maximising potential of EPB shield tunnelling technology. Challenges were posed not only by the difficult boundary conditions of urban shield tunnelling, such as shield drive under buildings, but also by complex geotechnical situations. PROJECT DESCRIPTION The great urban area of São Paulo is one of the biggest cities in the world, with around 20 Million people living in the city and in the suburb area. The city faces great mobility problems and in the last years the government has been investing great amounts on the megacity´s metro expansion. The Line 5 Extension plays an important role to connect the south area to the central area of the city, with a whole extension of 11 kilometres, including 11 new stations. It is estimated that this line will transport almost 900.000 passengers/day. The first stretch of the expansion, Lot 3, consists of two single tunnels, almost 5 kilometres long each, crossing 4 stations. Figure 1 shows details of the Line 5 Expansion."

Jan 1, 2016

By V. C. Koppe, J. F. C. L. Costa, D. M. Marques, A. Amaral

Errors associated with estimating the grade of an attribute of interest in a deposit can compromise planning, sequencing, and mineral beneficiation decisions. Several factors are associated with estimation errors. Among them, we can highlight the factors associated with sample spacing, the size of production volumes, and the variability of the attribute considered in the estimation. The access to estimation error can be obtained by some geostatistical methods, for example, by stochastic simulation. However, this is a process that in some situations is computer intensive and takes time. Previous works have proposed a simplified method to access the Maximum Estimation Error (MEE) associated with different types of grade variables, depending on the sample spacing, at small production volumes and considering specific coefficients of variation ranges. This paper presents an approach to assess the MEE associated with long-term volumes. Considering the methodology proposed, it is possible to approximate if a specific drilling pattern used in a deposit provides an acceptable pre-determined estimation error for Resource Classification. Results and considerations on the impact of the geometry of larger production volumes on the MEE calculation are also presented.

Jun 25, 2023

By R. W. Lankston

Uranium mill tailings disposal facilities present unique problems with respect to siting, design, and long-term stability because their contents remain potentially hazardous for 100,000 years. Dawn Mining Company, operator of a uranium mill in Washington, undertook geological and geophysical studies relative to planned expansion of existing disposal facilities. Seismic refraction and reflection, resistivity, and ground magnetics data were integrated with limited drill data to determine the configuration of Quaternary sediments and the underlying basaltic and granitic bedrock. Analysis of multiple reflections and magnet modelling on a micro-computer with CRT graphics added detail to the interpretation.

Jan 1, 1980

By B. Blaschuk

The Freeport McMoRan Bagdad Solvent Extraction (SX) circuit is the oldest plant of its kind currently in operation. The plant was commissioned in 1969 and was the second SX-EW operation to be built following the Ranchers Bluebird solvent extraction and electrowinning (SX-EW) plant near Miami, Arizona. Over the years of operation, the configuration of the SX has gone through many changes to accommodate a variety of pregnant leach solution (PLS) grades and flows. Although modifications to the original plant configuration are numerous, the Bagdad SX circuit has maintained its general form consisting of multiple long and narrow settlers. The unique configuration of the Bagdad SX circuit presents a variety of operational advantages and challenges; however, it continues to operate at a level recognized in the industry as excellent.

Jan 1, 2010

By Aydin Shaterpour Mamaghani, Cemal Balci, Nuh Bilgin, Mucahit Namli, Hanifi Copur

"It is expected that more than 10 Billion USD will be spent in Istanbul in coming years on tunnel boring especially with EPB-TBMs. However, the geology of Istanbul is very complex. Geologic formations changing from Paleozoic to Cenozoic ages cause tremendous problems due to frequently changed rock formations and andesite and diabase dykes. This paper summarizes a universal model to predict the performance of EPB-TBMs which is created upon the data base collected from several projects. The model first is based on predicting field specific energy and power consumed of TBMs using geo-mechanical properties of the excavated material and TBM diameter. Later net production rate is calculated using field specific energy and power consumed by TBM. A methodology to predict machine utilization factor permits to calculate daily advance rates. The validity of the model is tested using the data obtained from two recent metro tunnel projects. 1. INTRODUCTION It is expected that in a near future a total length of 400 km will be excavated in Istanbul in a complex geology. Selecting proper tunneling equipment, organizing an effective operational management with the right tunneling crew will be a major concern for an efficient scheduling of the future projects necessitating to create a model to estimate daily advance rates. Several TBM performance prediction models with few on the prediction of machine utilization time were realized in the past. However, there is quite limited number of research studies on predicting the performance of EPB TBMs. Specially predicting daily advance rates in complex geology, in mixed face, in fractured rocks, in transition zones etc. are in big concern (Namli et al. 2013, 2014). The first experiences in Istanbul with a gripper type TBM was a nightmare, roof collapses caused big delays in tunnel excavation (Bilgin 1993). A typical example to EPB-TBM was Kadikoy-Kozyatagi tunnel, changing TBM from opened mode to closed mode with few modifications on the cutterhead resulted a tremendous increase in the daily advance rates (Bilgin et al. 2009). The data collected from several tunnelling projects served a basis to create a model to predict daily advance rates of EPB TBMs. Within the frame of a research program the validity of the model was tested in Uskudar-Umraniye–Cekmekoy-Sancaktepe metro project and very recently in Mecidiyekoy-Mahmutbey project."

Jan 1, 2016

By William E. Robinson

Why did it fail? My first reaction when assigned this topic was to say: because somebody "goofed"--then thank you all for letting me say those few words, then promptly sit down. All of you have been bandying this problem around for many years--so all of a sudden I should come up with the solution. Well, While I might not provide you with your particular answer, I think I can show you some of the resolutions to it. Somewhere along your path of experience you may have discovered that a good formula for starting a fight is to tell a group of dedicated (Nordberg Crusher) users they should be using (Allis-Chalmers), or a group of (Allis-Chalmers) 'users they should be a (Traylor). Now, if you really want a melee, get both groups together and tell them they should be using a (Stedman Cage Mill). This is one sure way you can learn how great minds arrive at logical, well thought-out conclusions, based on all the relevant facts. Why did it fail? I could go on for hours giving you specific reasons why. One of my engineering professors used to start his new class off each year by writing on the blackboard--four and two, then turn to the class and ask: What is the problem? One brave scholar would venture to answer 8. His head would shake no. Another would dare 6. Again, a head shake. Now that the ball had gotten rolling, a number would vocally decide it had to be two, which produced only another shake of the head--no. All of them had missed the question he had asked : What is the problem? What he had gotten ,were some of the possible answers to the problem.

Jan 1, 1977