Search Documents

By Carolina Bruecker, Axel Preusse

"The topic of ground movements in Germany has been studied extensively in the past, especially in the field of active mines. The active hard coal mines were finally shut down in 2018 in Germany and lignite mining is expected to take place only until 2038. The so-called long-term liabilities of the mine operators in Germany include, among other things, the long-term guarantee of stability and thus the monitoring of ground motion.So far, the economic use of underground mining in Germany was mainly the supply of raw materials. In the future, the underground storage of compressed air, methane, or hydrogen will play an important role in renewable energy supply and climate change. Therefore, underground storage space will become more important and spatial planning is essential to ensure availability of safe underground openings for the various options of environmentally friendly energy storage.However, this renewed usage of underground openings may also bring new and sometimes unknown challenges of geomechanical influence. On the one hand, the aftermath of hard coal and lignite mining will be an increasing challenge in mining subsidence engineering. On the other hand, new possibilities due to underground spatial planning may lead to subsidence and/or heaving of the upper surface.INTRODUCTIONBoth hard coal and lignite have a long tradition in Germany. The Prosper Haniel mine in the Ruhr area was closed at the end of 2018 after 150 years, which signalled the end of hard coal production in Germany. Lignite mining still takes place in the Central German, Lausitz, and Rhineland districts. However, lignite mining in Germany is expected to be phased out gradually by 2038 (MDR, 2019). With the closure of these mines, however, mining damage is not over. The long-term consequences of mining, which extend far beyond the closure of the mines, are associated with the liability and responsibility of the individual mining companies. The so-called eternity burdens on the mining company continue to apply. In the field of lignite production, the discontinuation of dewatering and the resulting possible elevations of the surface will be a relevant topic for the future of mine surveying. The same applies to the hard coal mines, which are partially flooded in Germany and therefore require extensive monitoring of soil movements in the future.The discontinuation of energy from hard coal and lignite calls for a change in the energy mix. With the renewable energy revolution in Germany, the focus is on a sustainable and environmentally compatible climate and energy policy based on renewable energies. Sustainable use of the subsoil, both natural and anthropogenically produced cavities, will play an essential role in the objectives of this policy. For example, disused mine cavities can be used to store electricity from renewable energy sources. (Umwelt Bundesamt, 2018) These functions will again cause classical ground movements such as subsidence and uplift, but will also bring new challenges for the mine surveyor. Challenges can be underground cavity exploration in inaccessible areas or legal aspects of underground competition."

Jan 1, 2019

By Ingo Ossenbühl, Wolfgang Dolsak, Vojtech Gall, Axel G. Nitschke

"Yielding support systems for application in underground construction have a long history, primarily in mining. Typical examples are tunnels subject to loading conditions that lead to overstressing of the newly installed support or existing tunnel structures in active fault zones. Recent applications for tunnel rehabilitation projects unveiled the capabilities and flexibility of combined yielding support systems presented in this paper. Frequently, the main requirements for tunnel rehabilitation applications are a fast, safe, and simple installation along with the need for flexibility with regards to existing tunnel geometries. A combined support system consisting of steel sets with yielding connections and special groutable hoses has proven to be an efficient support measure providing a multitude of advantages compared to conventional rehabilitation approaches. The presented yielding support system provides an immediate and active support, while it allows for controlled yielding upon experiencing loads beyond its support capacity. INTRODUCTION The excavation of underground spaces leads to redistribution in the existing stress regime. This load redistribution goes along with deformations in the surrounding rock mass. Magnitude and duration of these deformations depend on the tunnel’s depth and geological conditions, but also on the installed support system. Modern civil tunneling infrastructure has generally an envisioned service life of about 120 years. Conventional tunneling provides typically a dual support system, split into the initial (or primary) and final (or secondary) lining. A typical design principle in civil tunneling is to let the vast majority of deformations acting on the initial lining cease, before the final lining is installed. Based on this approach, the loading on the final lining is significantly reduced and signs of overstressing, such as cracking of the lining, are typically limited to the initial lining. However, special cases in swelling and squeezing ground require different approaches, including yielding support systems."

Jan 1, 2016

By S. A. Anzalone

The Helvetia copper deposit is a large undeveloped Laramide porphyry copper system located in the Santa Rita Mountains, Pima County, Arizona. This porphyry copper system consists of four areas of copper mineralization: Rosemont, Peach-Elgin, Broadtop Butte, and Copper World. Asarco refers to the four areas collectively as the "Helvetia Deposit". Mineralization and alteration are primarily contact pyrometasomatic, and zoning of hydrothermal alteration and sulfide mineral assemblages are similar to those observed at the Twin Buttes and Mission copper mines located approximately 32 km west of Helvetia. Asarco acquired the Helvetia Deposit in 1988 and has continued the exploration and development effort since then. A considerable amount of excellent geological work has been completed in the area but little information has been published on developments since the mid-1950's. The geology of the deposit as developed by numerous geologists over the past 75 years and the large, bulk tonnage low grade copper deposits outlined in recent years will be briefly reviewed in this paper.

Jan 1, 1992

By John E. Frost

Duval's (now Battle Mountain Gold Co.) copper and gold deposits in the Battle Mountain District in Nevada are in two subdistricts - Copper Basin and Copper Canyon - about 18 km (11miles) apart. Location of the two subdistricts is shown in Fig. 1. The two centers of mineralization have distinctive geologic and ore characteristics that required different innovative approaches to exploration and development. Nearly all of the copper from Copper Basin has been recovered by heap leaching. Because of relatively high gold and silver values in the Copper Canyon ores, a significant part of the sulfide copper ores has been recovered by a conventional flotation mill at Copper Canyon. Recently, this mill has been converted to the recovery of gold that is mined from zones peripheral to the copper deposits. Prior to Duval's entry, small amounts of copper, gold, silver, lead, zinc, and antimony had been mined in the district over a nearly 100 year period, beginning in 1866. The bulk of the $13 million total production to 1962 was derived from copper and gold lode ores and gold placers. Duval's interest in Battle Mountain-arose directly from a submittal by Asarco, which controlled key claims in both the Copper Basin and Copper Canyon subdistricts. Asarco acquired its holdings in the district in 1959 and undertook limited exploration until mid-1961. At that time, the company decided to dispose of its interests. Duval was invited to evaluate Asarco's properties and accepted. On Dec. 6 and 7, 1961, J.E. Frost, R.C. James, R.W. Sayers, and H.A. Schmitt, representing Duval, and K. Richard and E.W. New- man, representing Asarco, visited Copper Basin and Copper Canyon. Frost concluded that the properties were of considerable interest and prepared, by Jan. 12, 1962, a voluminous report recommending that Duval acquire and explore Asarco's properties. Furthermore, he recommended a large initial exploration program that included not only geologic mapping, geochemistry, and geophysics, but also the extensive drilling that was to involve, as the first phase of exploration, 49 drill holes in Copper Basin and 21 drill holes in Copper Canyon. Following property agreements between Duval and Asarco, and Duval and several other claim owners, geologic mapping, geochemical surveys, and drilling began in August 1962. Exploration drilling was completed in July 1964 and engineering studies in April 1965. Development of the Battle Mountain properties was authorized in July 1965, and production commenced in the first quarter of 1967. Because of the unusually high oxide copper content of the ore bodies, particularly in Copper Basin, a much larger than typical proportion of the copper in the deposits has been recovered by heap leaching. The generalized geology and ore zones of the Copper Basin are as shown in Fig. 2 and of Copper Canyon in Fig. 3.

Jan 1, 1991

By Edward R. Borcherdt

When one considers the advancements made during the 25 years prior to the late fifties, and compares these advances with the progress made in the past decade, the comparison is indeed startling. It was not until 1935 that trucks began to replace rail as a major hauling facility, Initially, the haulage capacity of end dump trucks was limited to 18 or 20 tons. "Straight stick" transmissions were utilized and the available horsepower was minimal. In the early forties single planetary axle 25 ton trucks were introduced, and shortly thereafter those were followed by 35 ton tandem axle units.

Jan 1, 1967

By David M. MacGillivray

1. INTRODUCTION The economic importance of bringing a new mine to production in the shortest possible time, is well known. In recent years the rate of escalation of mining costs has accelerated more rapidly than at any time in the past. This fact has enhanced the need to reduce time schedules and made it an overriding and predominant objective when planning new shafts. The squeezed profit margins and widely fluctuating metal prices have also increased the emphasis being placed on this aspect. Moreover the increase in the present value of future profits due to the reduction in the time element, can be so substantial that expenditure on equipment and additional labour can be justified conditional on sufficient gain in shaft sinking speed being achieved. The emphasis on time saving becomes more abundantly clear when considering the very large increase in the capital required to bring a modern underground mine to production. As an example, the initial capital expenditure requirements for a large new gold mine in the Western Transvaal, which has commenced production recently, is estimated at R200M, and a major extension to another deep level mine in the same area is estimated at R300M. With the uncertainty of future metal prices and the recent trends in increasing inflation, it is becoming more difficult than ever to estimate the profitability of proposed mining projects and any cost saving due to more rapid sinking of shafts can only assist in this respect. Since the shaft systems are frequently the most expensive set of underground excavations and no other underground work can commence until they are completed, the speed of shaft sinking is subject to closer scrutiny than in the past. In the following sections of this paper the factors contributing to the high average advance rates achieved by South African shaft sinkers are discussed. It is difficult, if not impossible, to estimate the effect of any single factor, in isolation, on the overall sinking achievements. However, the cumulative effect of improvements made in the inter-related activities is, probably, the most important contributor. Although there has not been any single major technical change or innovation to shaft sinking practices in the last decade, the average sinking speeds have increased, due to improved application and technical improvements in established procedures. 2. GENERAL When discussing South African shaft sinking techniques and average sinking rates compared to those achieved in other parts of the world, it should be remembered that the size and depth of South African shafts are often considerably greater than in most other countries. Typical examples of shafts either in the course of sinking or recently completed are -

Jan 1, 1979

By Chris Lynagh, Collin Schroeder

Determining the best excavation method is a critical step in successful tunnel construction. In rock tunneling, several factors can dictate the excavation method, such as: (1) rock characteristics, (2) tunnel size and length, (3) nearby utilities/infrastructure, and (4) contractor’s preferred means and methods. This paper discusses the various rock tunnel excavation methods utilized on the Doan Valley Storage Tunnel Project (DVT), a project constructed as part of the broader Project Clean Lake in Cleveland, Ohio. The differences between each method’s initial and final lining, geology, and cycle sequence will be analyzed and compared.

Jun 13, 2023

By R. Gray

"Experience from Australia has identified what is referred to as non-conventional surface subsidence behaviour. This occurs under irregular surface topography, resulting in valley closure, valley floor uplift or “upsidence”, and far-field horizontal movements – even occurring beyond conventional “angle of draw” limits. This paper discusses such behaviour recently observed in Pennsylvania and focuses on the 2005 case of Duke Lake Dam in Ryerson Station State Park. In July 2005, there was a significant increase in water leakage through a number of growing cracks in the dam leading to the dam being breached to avoid an uncontrolled failure. An underground longwall mine was located approximately 900ft to the north, mining at depths of 330 – 720ft. Investigations (including a subsequent ground movement monitoring program) found a range of evidence in the vicinity suggesting that valley closure and far-field horizontal movements may have occurred resulting from the adjacent mining. The paper discusses the phenomenon of non-conventional subsidence behaviour and the Ryerson State Park case study, including an assessment of mining, geology and subsidence impacts and suggested ground behavioural mechanisms. INTRODUCTION Non-Conventional Subsidence The conventional understanding of coal mine subsidence on which most current subsidence understanding and prediction techniques are based, includes the concept of angle of draw which effectively limits the lateral extent of subsidence effects and impacts. Within this zone – above and marginally beyond the boundary of mining – downward vertical subsidence is the dominant component, together with localised horizontal movements towards the mined region, with related tilts and strains. However, more recent experience from Australia over the last two or three decades has identified what is referred to as non-conventional surface subsidence behaviour. This is found to occur in areas of irregular surface topography or variable terrain, and is characterised by phenomena such as valley closure, valley floor uplift or upsidence, and far-field horizontal movements, all of which can occur beyond the conventional angle of draw limits. NSW Department of Planning (2008) defined the conditions for both conventional and non-conventional subsidence behaviour as follows: “The conventional or general model of surface subsidence, which finds worldwide acceptance, is based on assuming the following site conditions:"

Jan 1, 2015

By Dani Delaloye, Kas Zurek

Evaluating and selecting the appropriate excavation method is a key to the success of any tunnelling project. The benefits and risks of different methods should be well understood by the designer and communicated to the project owner to enable selection of a preferred method from a technical, social and environmental impact, cost and constructability perspective. For tunnels that have an internal diameter around 3 m, depending on the tunnel purpose and ground conditions, both microtunnelling with pipe jacking and tunnel boring machine excavation with a one- or two-pass lining may be feasible construction methods. Using the Ferry Road and Riverbend Combined Sewer Relief Project located in Winnipeg, MB as a case study, this paper will discuss the benefits and drawbacks of each method, including technical design, social, environmental, cost, schedule, and risk considerations.

Jun 13, 2023

The rheological behavior of high concentrated coal -water slurry (cws), a new liquid fuel, is an important factor in the preparation, transportation and combustion. The conventional viscosimeters designed for Use with true fluids are not suitable to the measurement of the rheological behavior of cws. So that a special viscosimeter of tube type for cws was designed and set up in .laboratory. Experiments using two kinds of cws from two provinces from P. R. Olfna were conducted. It is found from test results that the experimental cws possess the rheological character of Bingham fluid and there is the existence of the wall effects which causes the measurement errors. In our former paper published the wall effects were discussed III the light of methods of Odroyd and Jastrzerbsiki to make the correction of the experimental results. But a number of tests are necessary to meet the need of determining the slip coefficient. In this paper the models of the wall slip velocity and the thickness of the slip layer of Bingham fluid were proposed III in theoretical approach which were satisfactorily used in the correction of the measured results of the rheological character of cws.

Jan 1, 1994

By Johan K. Rodenburg

A major bauxite belt was discovered and evaluated from 1969 to 1974 by P. T. Alcoa Minerals of Indonesia in West Kalimantan, Indonesia. The proven reserves of beneficiated bauxite are 800 million tons averaging 38.6% AA1203 and 3.0% RSiO2. Inferred reserves of washed bauxite are in excess of 2 billion tons. The bauxite occurs as capping of low lying hills which were formed during the post Paleogene peneplaination stage. The overburden varies from 0.6 to 3.8 meters and the nodular bauxite horizon from 2.2 to 5.2 meters. The deposits were formed by the in situ weathering of predominantly acidic and basic intrusive rocks.

Jan 1, 1984

By Joseph J. Garbarino

World demand for phosphate fertilizers has grown at an average annual rate of between 6 and 7 per cent over the past 10 years. In the next five years world demand is expected to at least continue to grow at that rate. Also, the continued need for improved fertilizer materials, coupled with improvements in fertilizer technology, have placed added importance on the use of phosphoric acid as a starting material for high analysis phosphate fertilizers. This demand for phosphates and phosphoric acid must be met by increased production. Increased phosphoric acid production also brings increased demand for chemical processing agents including foam control agents. We at Arizona Chemical Company have closely followed the phosphate fertilizer industries needs. Arizona Chemical Company has been an important supplier of flotation agents to the phosphate industry, primarily from its Panama City, Florida plant. We have also recognized the important role played by foam control agents in the wet-phosphoric acid manufacturing process. We feel it is the responsibility of the supplier of foam control agents to offer specifically designed products that are highly efficient and economically useful. The difficulties involved in evaluating foam control agents in the plant are recognized. Owing to the large number of variables present, and the difficulties in controlling these variables during the period of a plant trial, plant evaluation of a large number of foam control agents is impractical. We have attempted to develop a practical, reproducible, and yet rapid, laboratory evaluation test which correlates with plant performance.

Jan 1, 1966

By J. Roufagalas

Sustainable development requires that exploitation of environmental resources is such that it does not result in permanent damage to the environment. In many instances environmental damage is an external cost of the entity exploiting the resource. Ideally, the entity should be forced to internalize this cost. Various financial assurance schemes have been proposed to ensure that the entities fulfill their financial responsibility to restore the environmental dam-age. Prominent among these schemes are ?environmental bonding requirements?. A main issue with these financial assurance schemes is that many times the amount and duration of environmental damage is uncertain. That is, the cost of restoring the environment in the future may be unknown (or unknowable), and, furthermore, the extent of the damage may not be known for many years into the future. Nevertheless, bonding requirements have to be set in advance and the rules for returning the bond and absolving the entity of responsibility have to be specified ex ante. In practice, a problem of allocation of resources arises. To make sure that all external costs are internalized, in the face of uncertainty, will require a sufficiently (arbitrarily) large bond for a sufficiently (arbitrarily) long period of time. But such a requirement may prove too expensive and may result in not undertaking a project (even if, under certainty, the project may be profitable after internalizing all costs). This will result in a reduction in total welfare. Under present bonding requirements, firms are responsible up to the value of the bond. This results in an asymmetry: if environmental restoration is less than the bond amount, the firm has an incentive to restore and reclaim the bond; if the cost of the environmental restoration is above the value of the bond, the incentive is to forfeit the bond, imposing on the government/ society the excess cost. This also may reduce social welfare, at least on distributional grounds since the firm owners pocket the profits and the taxpayers foot the bill. The presence of uncertainty suggests that a fee based reclamation fund may be welfare enhancing. The thinking can be sketched as follows: All firms undertaking environmentally sensitive projects pay into the proposed fund. The fund examines the risks and sets the premiums at the level of the expected restoration costs (not the maximum!) plus administrative expenses. One advantage of the scheme is that this eliminates the asymmetry. Firms with restoration costs below expected end up subsidizing firms whose restoration costs were underestimated. In other words, the industry ends up internalizing the costs not internalized by the individual firms, instead of the taxpayers.

Jan 1, 2007

By T. Vandergrift, J. Sturgill, W. Gerhard, J. Carrick

As surface minable coal is depleted, many operators look to high-wall mining to extend reserve life. Recent advances in highwall mining equipment have greatly improved productivity, clean coal recovery, and attainable penetration beneath the highwall. Somewhat lagging have been systematic design approaches for ensuring web pillar and overall highwall stability. This paper presents an overview of the design, planning, and field performance of a multiple-seam highwall mining application in southwest Wyoming. The safety and efficiency obtained to date is attributable to the careful geotechnical and operational planning described herein. Field confirmation of performance and suggestions for improvement are also discussed.

Jan 1, 2004

By Adolf U. Honkala

Dundee Cement Company was incorporated in 1958. The equity capital for the venture was supplied by a Swiss firm called Holderbank Financier and a group of its principals. Holderbank Financier, a holding company, is a direct outgrowth of Holderbank Cement Company, a company founded in 1912 by the father of Dr Hans Gygi who is the president of Dundee Cement Company and a member of the Board of Holderbank Financier. From one plant in 1912 located in Zurich, Switzerland, Holderbank grew to its present size of 32 plants in 17 countries, having a capacity of 90 million barrels of cement per year. Dundee Cement Company constructed its first cement plant near the little town of Dundee, Michigan. This site was selected because there is an abundance of limestone and clay of the correct chemical composition for cement manufacture and the deposit was advantageously located near the large population centers of Detroit, Toledo, Cleveland, and Chicago. Construction of the 5. 5 million barrel, two kiln, plant was completed and the plant started up in the fall of 1959. After a year or two of the usual problems in a new plant and the expected difficulty of breaking into a nearly saturated market, Dundee began to prosper.

Jan 1, 1970

By Terence G. McCusker, E. Roy Anderson

A four-mile length of interceptor sewer tunnel in Manhattan has finished sizes ranging from 10'6" to 14'6" horseshoe. Mixed face conditions were anticipated in three areas and encountered in five. All were short but since the tunnel lies well below the water table and failures would involve important utilities, major structures and human lives, great care had to be exercized in choosing a construc¬tion method. Chemical consolidation was selected as the best approach with compressed air working as a backup system. Initially grouting was accomplished from within the tunnel, but treatment from the surface was more successful and was later adopted. The soils consisted largely of impermeable weak silts and it was found possible to inhibit access of water to this material so that it could be controlled by breasting within the tunnel without loss of stability. It is concluded that in the interlayered permeable and impermeable soils encountered, chemical grouting would successfully stabilize the working face. INTRODUCTION An interceptor sewer is currently under construction along the entire length of the west side of Manhattan. When complete, the tunnel will intercept and divert to a treatment plant (also under construction) a daily flow in excess of 200 million gallons per day. About 9 miles of the interceptor sewer is in tunnel and the remain¬der is cut-and-cover construction. The tunnel is almost entirely in Manhattan schist but where its alignment crosses major faults at comparatively shallow depths, mixed face and earth conditions are

Jan 1, 1997

By R. W. Mossman, George E. Heim

Seismic exploration techniques offer the engineer and geologist a way of obtaining detailed information on the physical parameters and geometry of the rocks where extensive underground excavation or tunneling is proposed. Use of the seismic method can provide a greater amount of detailed information at relatively less cost than can be obtained by any other known subsurface exploration method. Boreholes are still required for calibration of the seismic data but at a much wider geographic spacing than otherwise would be needed for subsurface mapping. The seismic data can define with precision the actual location of zones of flexure or fracture of the rocks and reveal the configuration of the surface of the rock layers. ENGINEERING PROBLEMS One of the major requirements in the planning of subsurface installations is that of locating tunnels and other underground openings in favorable rock units. Such rock units should exhibit uniformity of composition, both vertically and horizontally, to minimize variation in excavation techniques. The depth and thickness of the unit must be known: a 30-foot diameter tunnel cannot be contained in a 25-foot thick limestone. The rock unit needs to be as free as possible from structural defects and should be suited to efficient excavation procedures. If liquid conduits are planned, the slope of the rock unit needs to be known so that maximum advantage can be taken of gravity flow with the tunnels wholly contained within the unit.

Jan 1, 1997

By J. A. Bowersmith

The environment in which the surface mining industry operates today is considerably different than that of a few years ago. Increased pressure from the public, government, labor and internal industry factors calling for the fulfillment of rapidly changing expectations is especially intense in the surface coal mining industry. Such things as requirements for increased production, the Mine Health and Safety Act, environmental concerns and land reclamation, shortages of qualified and enthusiastic employees and market cycles coupled with price competition are but some of the specific items that are requiring the surface mining industry to better utilize equipment, materials, and labor resources available, There is one technical tool available which will assist management to increase productivity, improve cost control and assist in planning, organizing and operating surface mines. Industrial Engineering is that tool. Before a discussion of specific applications of Industrial Engineering to surface mining is conducted, it is worthwhile to review a definition of Industrial Engineering and the history of its development. The following definition has been adopted by the American Institute of Industrial Engineers: "Industrial Engineering is concerned with the design, improvement and installation of integrated systems of men, materials and equipment. It draws upon specialized know- ledge and skill in the mathematical, physical and social sciences, together with the principles and methods of engineering analysis and design, to specify, predict and evaluate the results to be obtained from such systems."

Jan 1, 1976

By C. H. Smith

The present interest in beryllium seems to be the result of recent developments in the uses for the metal discovery of significant deposits of disseminated beryllium ores, and the development of chemical and physical processing techniques, for recovering the beryllium values contained in these ores. At the present time most of the new and potential uses for beryllium are in the research stage of development and are not consuming large quantities of the metal. However, they do point to an expanding market. Interesting new discoveries or extensions of previously known deposits have been reported during the past year from the Boomer Mine in Colorado, the Mesquite area of Nevada,, the Chemalloy pegmatites in Canada, the Brazilian and African pegmatite districts and from other areas, However, this paper will discuss only four of the beryllium deposits, which appear to be of special significance due to their; large reserves of ore and promise economic development. The new chemical and physical processing techniques are not discussed in detail, but it should be stressed that the development of an economical process to handle the pegmatitic and low-grade non-pegmatitic beryllium ores is of great importance to the development of the beryllium industry. Scientists in both government and industry are co-operating in this effort and it is expected that commercial processes will be developed in the near future.

Jan 1, 1962

"Outotec’s TankCell® e500 flotation cell was commissioned during 2014 at the Kevitsa Mine in northern Finland. The TankCell® e500 is the first cell in this size class (500m3) to be run in an operational duty and it has been working as the first rougher in the copper flotation circuit. Treating around 850tph with an average grade of 0.3% Cu the TankCell® e500 has run with an average copper recovery of 71% and an average enrichment ratio of 50. In addition the cell has proved to be very energy efficient, operating with a specific energy of around 0.4kW/m3 under production conditions. This presentation will provide a review of the installation and operation of the TankCell® e500 at Kevitsa and will summarize the results found in the published literature from the various testing campaigns conducted around the cell. INTRODUCTION The TankCell e500 was installed and commissioned at the Kevitsa mine in northern Finland in 2014. Post startup the cell was initially run for testing and optimization with various test campaigns undertaken. but was subsequently taken into a production duty (Mattson et al., 2015a). At Kevitsa the cell is run as the first copper rougher replacing the previous two copper roughers (both 160m3) in this duty. The unit is running at between 38-40% solids at a feed rate of approximately 850tph. Since operational the average copper recovery from this single cell has been around 71% copper. This is typically with an enrichment ratio of around 50 being fed with an average head grade of 0.3% copper. More details on the circuit configuration and production performance of the e500 at Kevitsa can be found in Mattson et al., (2015a) and Murphy et al., (2016). In addition through the optimization program with the use of a variable speed drive controlling rotor speed it was found the the e500 was very energy efficient under production conditions. During this work the cell was found to run at a specific energy of around 0.4kW/m3 which exceeded design expectations (Xia et al., 2015)."

Jan 1, 2016