Search Documents

By Richard H. Olson

The following discussion will deal with the domestic talc industry only, inasmuch as the writer has had no experience in this field outside of the U. S. This is strictly a geological-mining approach; no attempt is made to assess in depth the effects which milling technology and marketing capability might have in determining the potential of any given talc deposit.

Jan 1, 1970

By A. Bruynesteyn

I would like to talk to you today about microbiological leaching or, the solubilization of metal values due to the action of Thiobacillus ferrooxidans. Bacterial attack of sulfide minerals has been going on for centuries but only recently was it discovered that the acid and iron often found in coal mine drainage is produced by bacterial action on the iron sulfides in the coals. Not until 1950 was it proven that bacteria were playing a role in the dump leaching of sulfide ores. B. C. Research became involved in microbiological leaching in 1955 while examining mine drainage from the copper-zinc mine at Britannia Beach, north of Vancouver. Since 1955, B.C. Research has maintained a continuous re¬search program on microbiological leaching which, due to its applied nature, was put under industrial sponsorship in 1962. Most of the information pro¬vided in my talk today has been gathered under this sponsored research program and I would like to express our appreciation to the many sponsors who have made our work possible.

Jan 1, 1970

By Kenneth G. Colman

Even though wet processes were used in coal preparation plants prior to 1941, dewatering coal was not a problem then because the finer sizes were uneconomical to recover and were considered waste. However, during the war years the scarcity of raw materials necessitated the utilization of every pound of natural resources and coal plants began seeking an economical mans of recovering fine coal. Early efforts to this end concentrated primarily on centrifugal dewatering devices. Such equipment produced good results but was relatively expensive. In 1944, a method was devised utilizing a vibrating screen fitted with a profile wire deck rather than the standard woven wire cloth deck. This machine came to be referred to as a dewaterizer. Results obtained with the dewaterizer approached those of the centrifugal equipment, but at a lower capital cost, Their use reduced either the number of centrifugal units required to follow the dewaterizers or the required energy input to heat dryers, In some cases they eliminated the need for any further dewatering equipment.

Jan 1, 1970

By E. R. Hoskins

The Gulf Coast States ranging from South Texas to Alabama contain vast resources of lignite ranging in energy content from about 4000 to 7000 Btu/lb (as-received) with sulfur content ranging from about 0.5 to 2 percent. Currently, the strip mining rate is about 35 million tons per year in Texas and essentially zero in the other Gulf Coast states. Estimates of future mining rates are as high as 310 million tons per year by the year 2000 with 240 being in Texas. In this paper, we examine the life cycle of the surface mineable lignice based on the most recent estimates of surface mine recoverable resources with two scenarios. The first indicates that a 310 million tpy rate could be sustained for only 15 years while the second scenario suggests that the 310 million tpy could be sustained for 25 to 30 years. If lignite resources are required beyond those that are surface mineable, the deep basin lignite will be developed. Five strategies for developing deep basin lignite are discussed.

Jan 1, 1983

By B. W. Firth

Increasing depth in vertical mine shafts penalises conventional hoists in at least four distinct ways: rope weight becomes limiting; travel time increases; the obstruction of ventilation becomes more serious; and with friction drives, rope wear due to torque is aggravated. Travel speed is limited by instability of poorly sprung conveyances on inaccurately aligned flexible rails, and also by the cost of installed power to meet an inherently peaky demand. These problems call for a review of existing designs, firstly in respect of the furniture (Buntons and guides) obstructing the air flow, and secondly in regard to the hoist running in the shaft.

Jan 1, 1969

By Luisa Alfieri, Giorgio Fantauzzi, Sergio Notarianni, Spencer Cavagnet, Alessandro Damiani

"The new tunnels of the Copenhagen ""Cityringen"" will be excavated, at Kongens Nytorv square, crossing over the existing M1 and M2 metro lines. After the crossing, the tunnels will underpass the historical building of the Magasin du Nord and adjacent masonry buildings, with a minimum tunnel cover of about 4.5 m. The tunnels have an internal diameter of 4.9m and are being excavated through earth pressure balanced Tunnel Boring Machines in mixed face.The Magasin du Nord estate is characterized by a very complex structure, with different blocks built in different times. An assessment of the condition of the building and its sensitivity to tunnellinginduced ground movements has been conducted through a fully coupled soil-structure interaction analysis; based on the results of this analysis, mitigation measures have been designed.INTRODUCTIONThe Copenhagen Metro Cityringen is expected to be running in July 2019 and will consist of two single tracks in a twin tunnels, each approximately 16 km in length, for transporting up to 243,000 passengers on an average work day. The Cityringen includes 17 underground stations with island platforms, 4 crossover facilities and 3 construction and ventilation shafts. The tunnels is being excavated using earth pressure balanced Tunnel Boring Machines and have an internal diameter of 4.90 m.The intersection with the existing M1 and M2 metro-line will take place at Kongens Nytorv and at Frederiksberg. According to the design alignment, in Kongens Nytorv the new tunnels will pass over the existing M1 and M2 ones; as a result of this, the tunnels will underpass the historical building of the Magasin du Nord and the adjacent masonry building hosting a Mc Donald’s with a minimum cover of about 4.5m.In the framework of Risk Assessment for sensitive buildings, the effects of tunneling-induced ground movements on the Estates ØS0437 (McDonald’s building), ØS0428 (Magasin du Nord) and ØS0004 (Hviids Vinstue) were evaluated. To achieve this goal a fully coupled soil-structure interaction has been considered and the entire excavation process has been reproduced in a 3D model where the abovementioned buildings have been modeled. In this way, a risk assessment analysis was performed evaluating directly the effects of the excavation in terms of settlements and variations of the internal forces as far as the excavation process proceeds. In figure 1, a picture of the construction of Kongens Nytorv station, with Magasin du Nord and Mc Donald’s building on the background, is presented."

Jan 1, 2016

By G. J. Goldberg

Through the early 1980's, surveying at Bingham Canyon required a great deal of repetitive and manual work. The advent of total station surveying equipment provided an opportunity to improve the speed and accuracy of surveying work while reducing manpower needs. An evaluation of total station systems and their ability to meet the surveying requirements of Bingham Canyon culminated in the purchase of a total station system as the mine re-opened in 1986. This paper presents the procedure for evaluating, implementing and using the total station survey system at Bingham Canyon.

Jan 1, 1990

By Peter L. Dunn

With the advent of new high-strength magnetic materials, rare-earth magnetic separators have become more common place for processing heavy mineral sands. In many instances, rare-earth magnets have replaced conventional separators such as electromagnetic cross-belt and induced-roll type machines. This paper will present the results from a detailed test program developed to evaluate the performance of rare-earth drum and roll separators for processing heavy mineral sands. The effect of machine design parameters, such as magnetic element configuration and separator diameter, will be reviewed in light of these test results. The impact of basic operating parameters (i.e. feed rate and roll speed) on separation efficiency will also be presented.

Jan 1, 1999

By John R. Keith

Keith, John R. 1968. Relationships of lead and zinc contents of trees and soils, Upper Mississippi Valley District. Preprint, Fall 1968 Meeting, Soc. Mining Engineers of AIME. Lead and zinc contents of elm, maple, and oak trees and of soils in which the trees grew were determined in samples from the Upper Mississippi Valley mining district, and from an area outside but contiguous to the district. The lead and zinc analyses of plant materials served to differentiate the mineralized and non-mineralized areas. Stems contained about two times as much lead and about 2-5 times as much zinc as did leaves taken from the same stems. Lead and zinc analyses of all soil horizons could be used to differentiate between the two areas. Soils at most sample sites in the mineralized district seemed to be more reliable than plants for geochemical prospecting and are a more practical sampling medium. Soil samples from areas with thick loess cover, however, failed to indicate the presence of mineralized bodies whereas tree samples from the same sites contained anomalous amounts of lead and zinc. It is suggested that in areas of thick loess cover plant samples could be used in prospecting for lead and zinc.

Jan 1, 1968

By John C. Nixon

In 1959, The Australasian Institute of Mining and Metallurgy (Aus. I.M.M.) was asked by the Federal Government of Australia and the State Government of South Australia to join in the formation and management of a new contract research organization which was subsequently named The Australian Mineral Development Laboratories (Arndel) ? This body was formerly the Research and Development Branch of the South Australian Department of Mines which had been set up to develop the Radium Hill uranium deposit. It had then gone into contract R&D and the State felt that it would be more appropriate for the Branch to become a separate national organization. The Aus. I.M.M. decided that a professional institute could not participate directly in Arndel and, as there was no other suitable industry group to do so, it formed the. Australian Mineral Industries Research Association Limited (AMIRA). AMIRA held its first Annual General Meeting in September 1959 when the first Council was elected and the Memorandum and Articles of Association were adopted. The initial task of AMIRA was to raise guarantees of work or cash from its members to underwrite Arndel for the first five years of operation. The Federal and State Governments also provided guarantees and Arndel commenced operations in January 1960.

Jan 1, 1977

By Alfredo Menendez, Alberto Sarmentero

A B S T R A C T The Los Pijiguaos bauxite is one of the largest accumulations of trihydrate alumina ore recently discovered; it is a plateau type, with no overburden, relatively soft tertiary quartz-bearing bauxite developed on a pre-Cambrian Rapakivi Granite batholith. The deposits are found in the northwestern rim of the Guiana Shield, State of Bolivar, Venezuela, and were discovered in 1976 after a grass-roots exploration campaign. Target areas were mainly selected on the basis of geological and geo¬morpholigcal criteria, guided by correlation with known deposits elsewhere in the Guiana Shield. The vertical. lateritic profile consists of an upper concretionary zone, followed by a mottled zone, a palid zone and finally the weathered rock merging into fresh granite. The upper concretionary zone displays a cellular, pisolitic or spongy texture and contains the following minerals: gibbsite (60-90%),quartz (5-10%), hematite (5-10%), goethite (under 5%), boehmite (traces), kaolinite (traces). The gibbsite content decreases sharply downward from the lower limit of the concretionary zone and the kaolinite and quartz content increases in the underlying mottled zone. The mottled and palid zones display a pseudo rapakivi texture and quartz, kaolinite and mica are the. essential minerals.

Jan 1, 1984

By J. A. Herbst

Mineral liberation modeling can be traced back to the early work 0fA.M. Gaudin up through more recent population balance modeling by R.p. King, J.A. Herbst and G.T. Adel. A more micro-scopic look was taken at the University of Utah in the form of the J.E. Sepulveda and J.D. Miller Pargen model which permits the creation of an arbitrary shape, multiphase particle made up of discrete grains. Recent work on image analysis and tomographic analysis by J.D. Miller and C.L. Lin have laid the experimental ground work for model validation, but until now it hasn't been possible to include the necessary physics of the particle stressing process to allow the development of a 'ffirstprinciples"mode1 which does not presuppose a "mode” of liberation (e.g., random or by detachment). Recent developments in discrete grain breakage (DGB) modeling now make a generalized physics based model feasible. This paper describes current work that is being done to develop a physics based discrete grain liberation (DGL) model. Two-dimensional and three dimensional simulation results exploring the effects of particle size, phase properties and loading type are presented. Relationships between energy based liberation efficiency, degree of random liberation and material properties are identified.

Jan 1, 2005

By J. Payton

Public Service Company of Oklahoma began burning sub-bituminous coal in December, 1979. Initially PSO had a single source coal supply from Jacobs Ranch Mine, and in 1982 added deliveries from Clovis Point mine. Both are Powder River Basin (Wyoming) coal mines. In 1986 PSO began burning Oklahoma coal to meet Oklahoma's 10% native use law. PSO experienced random s lagging during certain blends of these coals. PSO installed a boiler performance system to help control the slagging problems from the various coal blends, to improve boiler efficiency, and increase total coal consumption.

Jan 1, 1990

By T. E. Durney

In the Fall of 1987 The Wellmore Coal division of The United Company installed a fines separation circuit in its #20 plant near Big Rock, Va. The addition of the fines circuit included a bank of classifying cyclones and two flotation units; one a conventional 4 cell, 34 m3 Wemco cell, the other an 2.4 meter diameter by 7.6 meter tall, 28.3 m3 column flotation cell. The new fine coal separation circuit is depicted in Figure 1. The column flotation cell is manufactured by the Deister Concentrator Company, Inc., under the trade name Flotaire. The Deister Flotaire column cell utilizes a counter current flow arrangement and a different means of generating air bubbles than that of conventional mechanical flotation cells found in coal processing plants. Other features include diffusers for additional air supply and a froth washer. This cell is one of the few commercial scale column cells processing coal.

Jan 1, 1990

By James Crosby

The Urad property had been worked intermittently for over 50 years before American Metal Climax (AMAX) started an extensive exploration program on this property in 1961. The detailed studies of the property proved a large ore body of low grade molybdenum ore that could be mined by modified panel caving methods. Mine development and mill construction for a 5000 TPD operation was completed in July 1967. The Urad mine and plant site is located 55 miles west of Denver near Berthoud Pass. The plant elevation is 10,200 feet. The crushing plant is located underground because available surface area is re¬stricted by snow slide hazards. Crushing plant layout and ventilation system design for the Urad mine was based on our operating experience at similar crushing facilities located at the Climax operations. Low speed conveyors of generous width, adequate exhaust volumes at all ore transfer locations, large hoods and good conveyor skirting have made the Urad underground crusher dust control operations very satisfactory. Good maintenance and cleanup of the crusher facilities have made a clean working area with very low dust exposure. The ore from the mine is dropped approximately 1000 feet through ore passes to scraping drifts above the crusher and then transferred to the coarse ore bin by 150 h.p. slusher hoists. A reciprocating plate feeder under the coarse ore bin feeds a 48 x 60 jaw crusher. Ore from under the crusher is conveyed on a 48 in. belt to a vibrating screen where oversize passes through a 7 ft. Standard cone crusher. The crushed ore along with the screen undersize is conveyed on a 42 in. belt to a 1000 ton surge bin.

Jan 1, 1971

By Howard W. Earnest

The Rio Blanco Oil Shale Company completed a modified in situ oil shale retorting demonstration at its Tract C-a Lease in the Piceance Creek Basin of northwestern Colorado during the spring of 1982. This demonstration was the first MIS project with shafts rather than adits for access to the mining operation, and it involved several potential hazards which required that particular attention be paid to mine ventilation. Methane was first encountered during shaft sinking and ultimately resulted in the mine being classified gassy by MSHA. Secondly, we encountered hydrogen sulfide in association with the ground water, and this proved to be a more persistent problem than did the methane. Thirdly, in order to burn the underground retorts, it was necessary to provide for potential leakage of retort gases and to obtain a modification to the MSHA standard which forbids fires under- ground. This modification had a significant effect on the ultimate ventilation procedures at Tract C-a. An extensive under- ground air monitoring program was included in the ventilation system.

Jan 1, 1983

By P. N. Thompson

The past few years have seen the introduction of mini-computers on an increasing scale at collieries in the British coal industry. These are being used for controlling underground transport systems, coal preparation plants and fixed plant (pumps etc.); and for monitoring the mine environment and face operations.. A separate mini-computer (termed a primary computer) is dedicated to each of these functions. The overall system under which these computers operate is a common one which is applicable at all collieries. The information collected by the primary computers, other than that required for immediate control, will be fed to a secondary computer for analysis and processing. This overall concept, called MINOS. (MINe Operating System) is being developed by the National Coal Board's Mining Research and Development Establishment (M.R.D.E.). Eventually most of the data required by the system will be captured automatically. For example, the fact that a delay has occurred on a face, together with the duration of that delay, will be detected automatically via transducers link linked to a primary computer. However, the reason for that delay will, in all likelihood, have to be recorded manually. Such a system is currently under development with the first trial installations now being made.

Jan 1, 1979

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sink times were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1% and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying and dumping of coal products by comparison to airborne dust capture from sprays.

Jan 1, 2013

By Bruce McKinstry

INTRODUCTION In June of 1992, the Bureau of Reclamation, United States Department of the Interior, awarded the contract for construction of the Sixth Water Aqueduct to the Fedrick-Redpath Joint Venture. This aqueduct, a segment of the Diamond Fork Power System, Central Utah Project, diverts water from Strawberry Reservoir into Sixth Water Creek and, when complete, will replace the old Strawberry Tunnel which was driven in the early 1900's. The new aqueduct is being built primarily as a result of deterioration of the old tunnel, but will also have a higher capacity and more positive control than the old tunnel as well as the capability to incorporate a turbine into the system at a later date. The Fedrick-Redpath Joint Venture is comprised of C.R. Fedrick, Inc. of Novato, California and J.S. Redpath Corporation of Tempe, Arizona. Fedrick, with its experience in pipelines and heavy construction, will construct the 4200 ft surface pipeline and flow control structure; Redpath, the managing partner, performed the underground work consisting of a 600 ft vertical shaft and 3300 ft tunnel. The project is located in the Uintah National Forest, approximately 20 miles east of Provo, Utah at a mean elevation of 7000 feet above sea level.

Jan 1, 1995

By K. Anim, C. Calderon-Arteaga

Located in Mojave, CA, The Soledad Mountain mine is an Open pit Heap-Leach gold Mine, which is operated by Golden Queen Mining Company LLC. under private capital. Open pit mining began in 2015 while full production was reached in 2016. The open pit mine feed a processing plant that can process more than 13K tons per day of ore which is sent to a heap leach pad. The Soledad Mountain project is a poly metallic deposit with Au and AG being recovered as payable metals. As the mine became bigger after moving to the east pit phases, Golden Queen was facing new challenges to control the production and accurately determine KPIs to improve/increase the production. To maximize returns and asset value, a new fleet management system (FMS) was adopted and implemented. The new FMS has enabled the mine to interconnect the different stages of the mining, as well as to recognize issues and implement the necessary corrections. With the associated increase in complexity in the process, the requirement of the ore control system to accurately predict ore feed characteristics is critical to maximizing metal recovery. Implementation of new daily and weekly plans were needed to ensure the ore delivery and meeting the tonnage goals, while allowed the equipment operators to better geolocate and to maximize the equipment production. These conditions alongside with Golden Queen’s drive to increase profitability and maximize net asset value has created challenges. These challenges are numerous and multifaceted. However, the ability to accurately route the material from the mine, is critical to site success and some of these challenges have been overcome by the adoption of the new FMS, the implementation of daily and weekly plans and upgrades in the ore control workflow. Examples of how the integration of the new systems allowed golden Queen to improve production strategy, are discussed in this article.

Mar 2, 2022