Search Documents

By M. Gobla

"Since 1994 the Bureau of Reclamation has used risk analysis to evaluate dams. Risk considers both the likelihood of failure and the expected consequences should failure occur. Risk analysis relies on the detailed formulation and critical analysis of all possible potential failure modes. Potential failure modes are formulated by describing the sequence of events that must occur to result in failure, where failure is defined as the uncontrolled release of the impounded reservoir. Failure occurs in response to loadings such as water seepage through a dam (static forces), shaking from an earthquake (dynamic forces), sudden flood inflows (hydrologic forces), or accidental overfilling (operational errors). Reclamation has applied risk analysis methods to inactive and abandoned mines to evaluate tailings dams and flooded underground mines. Case histories of potential failure mode analysis as applied to mine impounded water illustrates what critical technical information is needed to determine if failure is likely, what the consequences of failure are likely to be, and what are the highest risks that should be addressed first. INTRODUCTION Impounded water, and high water content wastes, at mining and industrial processing sites are potential threats to public safety and the environment. Recent failures such as the TVA Kingston flyash impoundment failure in Tennessee in 2008 (5.4 million yd3 released), the Mt Poly Tailings Dam failure in British Columbia in 2014 (5.8 million yd3 released), and the Smarco Fundao Tailings Dam failure in Brazil in 2015 (78 million yd3 released) has renewed attention to this issue. Potential risks from impounded water at mining and industrial sites originates not only from tailing dams, but also from water in process ponds and conveyance pipelines, sediment retention dams, water retention dams, mine pit lakes, and flooded underground mine workings. Conventional water retaining dams also have a record of failure. Notable examples of failure include Vajont Dam in Italy in 1963 (2,600 lives lost), Banqiao and Shimantan Dams in China in 1975 (171,000 lives lost), and Machhu-II Dam in India (10,000 lives lost). After the 1976 Teton Dam failure in Idaho, the Bureau of Reclamation (BOR) established a Dam Safety Program. By 1984 the agency developed and began using risk analysis methods. Reclamation operates and maintains an inventory of hundreds of aging dams which were designed and constructed over a period of one hundred years. Many of these facilities were constructed using engineering design and construction methods which would not be considered good practice according to present day standards. Diligent observational monitoring, detailed site investigations, and the application of risk evaluation to the BOR dam inventory has identified many deficiencies resulting in significant demands on available funding for remediation efforts. The application of risk analysis has allowed the agency to rank sites by risk. By giving priority of remedial efforts to high risk sites, significant improvements to dam safety have been achieved. BOR has also applied risk analysis to evaluate and reclaim inactive and abandoned mining and industrial sites. The application of risk analysis methods in the mining industry is not new, the methodology was transferred to the mining industry more than 15 years ago as discussed in ICOLD Bulleting 121 (ICOLD, 2001), yet failures persist. This paper is meant to convey the lessons learned from BOR’s use of risk analyses in its work on mine sites."

Jan 1, 2017

By J. Swensen, R. Brandon, A. Wallstein, S. Bessinger, J. Pile

It is generally agreed that C.C. White was the first to describe and market coal mine roof trusses beginning as early as 1967. White was issued a patent in 1969 1. Coal mine roof trusses were extensively used in the 1970’s, and their use has proven valuable in many difficult conditions. Beginning in the mid 1990’s, several types of bar/cable trusses have been introduced. A new and innovative bar/cable truss recently introduced offers several advantages. By eliminating many small parts, and simplifying the installation, these new trusses are much easier and faster to install, thereby increasing operator safety.

Jan 1, 2004

By Paul B. Queneau, Barry J. Hansen, D. Erik Spiller

Most lead and zinc secondaries are recycled pyrometallurgically. However, many problems encountered in secondary smelters have been solved by addition of physical concentration and/or hydrometallurgical processing steps, with resulting important environmental benefits. U.S. secondary lead and zinc operations are described, covering conventional smelters, EAF-dust treaters, and zinc sulfate/fertilizer producers, including plant capacities, technologies, and outputs. During the past two decades, remarkable advances have been achieved by recycling spent lead-acid battery components. Interaction between primary and secondary zinc producers, the fertilizer industry, and the zinc chemical industry has substantially decreased waste generation.

Jan 1, 1993

By Daniel R. Stewart, Ralph R. Sacrison

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines, support definition and slope stability at the Climax mine, and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1992

By C. M. Liu

"The Freeport-McMoRan Sierrita Crystal Plant produces Copper (II) Sulfate Pentahydrate (CuSO4·5H2O) through a series of cooling crystallizers. In this process, high supersaturation and unwanted spontaneous nucleation promote fine crystals. Seeding through recycled crystal classification can manipulate the crystal size distribution (CSD) for larger crystals. Proper selection of the crystallizer for seeding can prevent spontaneous nucleation and promote final crystal size. This study shows when seeding temperature is closer to the crystallizer temperature, suspension densities in the crystallizers are promoted and overall CSD shifts to a larger size of crystals. INTRODUCTION Figure 1 shows an overview of the crystallization process. The in-plant feed flow, called Pregnant Mother Liquor (PML), enters the first crystallizer and is subsequently cooled through a series of four crystallizers. Specific temperatures are targeted for each crystallizer to ensure the crystallization process is operating within the metastable zone (MSZ). The discharged flow from crystallizer #5 then enters two cyclones. The overflow from the cyclones contains smaller crystals providing seed crystals for crystallizer #5. The underflow from the cyclones begins the drying process. The overflow from crystallizer #5 enters cyclone #3 for removal of fine crystals and seeding purposes. The underflow from cyclone #3 has the capability to provide seed crystals for crystallizer #1 or crystallizer #2. The overflow leaves the system as Spent Mother Liquor (SML). Undersize crystals dissolve into the PML and return back to crystallizer #1.THEORIES AND METALLURGICAL TESTS Seeding requires an understanding of the crystal size, solution temperature and amount of crystals that enter the crystallizers (1). For the seed crystal size, classified crystal seeds can prevent fine crystals returning back into the system which eventually leads to excessive agglomeration (2). Proper selection of the crystallizer can ensure seeding at an appropriate temperature. Seeding at a temperature much lower or higher than the saturation temperature promotes spontaneous nucleation. Typically, seeding between 4-5°F below the saturation temperature is acceptable (5). A general rule of thumb is to add the seed crystals at the temperature between the solubility curve and the metastable zone. An experiment conducted by Mettler-Toledo AutoChem, Inc. indicates seeding close to the solubility curve rather than the metastable zone promotes a lower supersaturation and nucleation rate but yields a higher growth rate and a greater number of larger crystals (1). The amount of seed crystals can not only change the suspension density but also narrows the width of the MSZ in the crystallizers. An experiment conducted by Jaroslav Nyvlt reports with the crystals absent, the maximum allowable undercooling is 6.3 degrees at a cooling rate, 5°C/hour. With the presence of crystals, it narrows the MSZ width to 2.2 degrees (4). Industrial crystallizers normally operate at suspension densities between 15% and 25% by mass. When suspension densities are lower than 15%, it increases the risk of primary nucleation and the probability of incrustations; on the other hand, if the suspension densities are greater than 25%, it can cause a greater attrition rate and increase the probability of deposits (6). Moreover, operating suspension densities between 15% and 25% are also sufficient to minimize supersaturation rate which promotes crystal growth over nucleation (2, 6)."

Jan 1, 2015

By B. Weaver

Every year Pit & Quarry Magazine surveys the industry to produce their annual review. Here's a sampling of some of the statistics the survey produced from the end of the year 1994 survey.

Jan 1, 1995

By Marco Aurelio Piangatelli, Massimiliano Bringiotti, Ferdinando De Angelis

"The construction of the three connecting tunnels between the east side and the west side of station C13, adjacent to the Vistula river, has a long and complex history, as they cross beneath one of Warsaw’s main road arteries (Wislostrada). After the attempt to excavate the first tunnel, the face of the tunnel collapsed on the night of August 13, 2012, and a volume of about 10,000 cubic meters of liquid mass (water, silty soil and sand) entered and flooded the west side of the station, which was filled with more than seven meters of material. Fortunately, the workers managed to escape, but machines and equipment were lost. This is the story of how the tunnels were completed, by adopting soil improvement, jet grouting, GRP bars, ground freezing and a careful choice of work steps. INTRODUCTION The Centrum Nauki Kopernik station on Line II of the Warsaw Underground is located alongside to the Vistula river (Figure 1). This station hereinafter is referred to as station C13.The station consist of three parts: the east and west part, and three connecting tunnels 40 meters in length with a large cross section (170 m2).. It includes the rails along the sides and the platform along the centre. The reason for the underground connection of two shafts with a tunnel is due to the presence of a road tunnel (Wislostrada, hereinafter called WS), which must be underpassed by the new metro line (Figure 2).The existing tunnel (Wislostrada) was built many years before, between diaphragm walls, and some foundation structures interfere with the underground tunnel. The challenge was to build the connectors without stopping the traffic of vehicles along the highway above. All works took place in very difficult geological and groundwater conditions due to the presence of Vistula alluvial deposits with poor mechanical characteristics. The soil profile consists of relatively loose sands on top, and silts overlying high plasticity Pliocene clays highly disturbed by the effects of the repeated over-sliding of glacial moraine deposits."

Jan 1, 2016

By Jiang Su, Michal Uhrin

"The use of composite linings, consisting of permanent sprayed primary and secondary linings with a sandwiched spray applied waterproofing membrane is expected to improve efficiency and reduce lining thickness, but it also brings complex primary-secondary lining interaction. This issue is further complicated by the uncertainty regarding the long-term behavior and parameters of the sprayed concrete–sprayed membrane interface.This paper aims to address this issue by presentation of a series of numerical analyses of a typical shallow SCL tunnel in soft ground with a range of design assumptions on the interface behavior: (1) compression only; (2) compression and tension; and (3) compression, tension, and shear.The results demonstrate that the assumed interface behavior has a significant impact on the primary-secondary lining interactions. A design approach of ignoring the tension and shear bond at the interface may not be conservative particularly for serviceability. This paper explains the rationale behind these conclusions and discusses the implications for design.INTRODUCTIONSprayed Concrete Tunnel Lining SystemsSprayed concrete linings (SCL) have been used in conventional tunneling for decades. However, details of SCL systems may differ to a large extent depending on ground conditions and specific tunneling methodologies.In hard rock conditions, for example, drill and blast excavation is typically supported by rock bolts and sprayed concrete (NGI 2014). Such tunnels are usually designed fully drained and the above-mentioned support elements considered permanent without the need for a further inner liner. Therefore, there is no structural interaction between separate lining shells to consider.In conventional tunneling in the European Alps, a double shell lining is typically utilized, consisting of an outer (primary) sprayed concrete lining and an inner (secondary) cast-in-place concrete lining, separated by a waterproofing system. The primary lining normally includes rock bolts and may include other support elements. The waterproofing system is usually based on a plastic membrane and a geotextile fleece. The tunnel may be designed fully or partially drained or fully undrained. Although there are two structural lining shells interacting, investigation of such interaction is generally irrelevant to designers because the primary lining is considered only temporary (fully sacrificial in the long term). An overview of reasons for this assumption is given, for example, by Lemke (2014). The secondary lining is designed to resist all foreseeable loads on the tunnel. The primary lining may, in reality, interact structurally with the secondary lining during the life span of the tunnel. However, since the secondary lining design must cover all possible (extreme) scenarios, investigation of such interaction does not bring any value to the design."

Jan 1, 2016

By Richard C. Fox

"Why geophysics? We will have to drill anyway." Reliance on geophysical methods for detailed target appraisals will increase as direct surface evidence becomes more subtle. This will create a need for more effective and efficient geo- physical programs. Numerous computer-based techniques that deal with a broad range of geophysical problems are described in the literature. The purpose of this chapter is to provide a framework for the systematic application of these techniques to effect an overall optimization of the geophysical appraisal. The concepts described are not technique specific, but should serve as a guide for increasing the effectiveness and efficiency of any geophysical program. Fig. 1 shows a generalized flow chart of the major aspects of the program described. The three main subdivisions of a 'geophysical program are discussed: (1) survey design, (2) data processing, and (3) data interpretation. Detailed flow charts, outlining the goals, the requirements for meeting the goals, and the steps followed within each subdivision are presented at the beginning of each section. The objectives and type problems of each subdivision are defined, followed by a description of applicable computer methods. . References are cited that give a general cross section of computer techniques available in the literature, and examples are given in each subdivision to demonstrate basic concepts and the use. of computers in solving the type problems.

Jan 1, 1979

By Philip K. Chan

Batu Hijau is a new copper and gold mine located on the island of Sumbawa in the Republic of Indonesia. This paper details the design and construction of the Batu Hijau overland conveyor, one of the most challenging efforts of the project. The 1.8 m wide, 5.6 km long conveyor has a design capacity of over 10,000 mtph and carries primary crushed ore through the steep mountains of Sumbawa, which necessitated a 160 m vertical downhill section, a 75 m vertical uphill section, ten vertical curves and one horizontal curve.

Jan 1, 2000

By D. Malhotra, R. M. Hoover

The effect of a surfactant, designated Syntex, on the wetting and spreading of hydrocarbon oil on molybdenite surfaces (faces) has been investigated experimentally through measurements of zeta potentials and factorially designed flotation tests. These studies indicate that Syntex has a positive effect in increasing molybdenite recovery in the rougher flotation circuit at the Climax mill. The analysis of experimental data using DLVO theory shows that the controlling factor in determining the magnitude of the repulsive energy barrier preventing oil from wetting and spreading on the molybdenite faces is the MoS2 zeta potential and the vapor oil droplet size. The role of Syntex in this case seems to be related to the decrease and stabilization of MoS2 zeta potential by Syntex adsorption and also to the emulsifying action of Syntex on vapor oil to provide a more favorable oil particle size.

Jan 1, 1976

By M. J. Virnig, Marc Le Vier, Rong Yu Wan, Jan D. Miller

Although most gold production from primary resources is achieved by cyanidation, many research activities have focused on alternative processes using noncyanide lixiviants. Such research has been prompted by environmental concerns and problems associated with the processing of refractory gold ores. Numerous research projects have been conducted to search for a noncyanide hydrometallurgical process for gold extraction. In this paper, a technical review of gold recovery from noncyanide solutions is presented, and new results are reported. Gold recovery techniques that are considered include activated carbon adsorption, cementation, solvent extraction, ion exchange, and reduction-precipitation.

Jan 1, 1993

By Paul C. Schmall, John F. Donohoe, Arthur B. Corwin

In the aftermath of the September 11th attack on the World Trade Center, groundwater control was of immediate concern. Water in?ow from the adjacent Hudson River through the compromised slurry wall ‘bathtub’ surrounding the site, ruptured water and sewer mains, and saturation from fire hoses all contributed to an already critical situation, further hampering the recovery and rehabilitation effort. An extensive pumping and deep well installation program was initiated, focused on reducing the hydrostatic loading to the severely damaged perimeter slurry wall.

Jan 1, 2003

By Kugan Kuganathan

Pastefill is being increasingly considered as a viable fill by underground mine operators. Mount Isa Mines (MIM) chose pastefill to fill their deep copper mine (>1200m deep) after considering various other types of fill in the feasibility studies. During the development of pastefill at Mount Isa (1996 - to date) the Mining research of MIM developed two cost effective, reliable and simple testing methods and used. With the help of these tests the behaviour of MIM pastefill was studied thoroughly and the most optimum mix design for pastefill was achieved. The MIM's pastefill plant, the largest in the world with a capacity of 450rph continuous pastefill production and unique in the process used, has been built (1998-1999) to produce pastefill to the specification developed through extensive testing program using the Flow Cone and Mini Slump cone Tests. As a consequence, it is now possible to select the optimum pastefill mix designs and predict their flow behaviour in bore holes or pipe lines using only these tests. MIM Blended Tailings Pastefill (BTPF) uses 3-3.55 Portland cement and the cost of pastefill is much lower than the total tailings pastefill, that could be produced from the same tailings.

Jan 1, 2001

By Gordon T. Clark, Stephen H. Gleaton

This paper discusses the conceptual design of cut-and-cover tunnels currently being considered as one of the replacement options for the earthquake damaged, elevated double-deck highway and seawall built in downtown Seattle 50 years ago. The 4.8 km (3 mile) long, 6-lane improvement consists of 1.6 km (1 mile) of at-grade roadway with aerial interchanges, 1.6 km (1 mile) of large two-level cut-and-cover tunnels along the Elliott Bay waterfront, and retrofit of the 50-year old, 1.6 km (1 mile)long Battery Street tunnel and north transition to grade. Construction of deep cut-and-cover tunnels, in complex glacial geology overlain by hydraulically placed fill immediately adjacent the existing sea wall, will require extensive use of concrete diaphragm walls, ground improvement and dewatering. The potential liquefaction and lateral spreading of the fill materials in this active seismic region pose significant design challenges and risk.

Jan 1, 2003

By T. R. Ellis

The vast majority of valuations produced for mineral properties using the net present value method provide an estimate of investment value or use value. Such an estimate can be a long way from the price that the property would actually sell for if placed on the market. Indicators from the market need to be used to validate or modify the net present value calculation if market value is being appraised. The comparable sales and replacement cost methods used in the appraisal of urban buildings generally fail when used in the appraisal of mineral properties. Other methods of sales analysis are introduced. Guidelines for what a minerals appraisal report should contain are presented.

Jan 1, 2002

By S. K. Kawatra, Harrison R. Cooper

In the last 30 years, on-¬stream slurry analyzers have proven to be of great use in the control of mineral processing circuits. This review discusses the two most popular methods, x-ray fluorescence and neutron activation analysis, and also considers techniques which are still under development.

Jan 1, 1986

By Robert Bissonette, Samir Sbai

Machine Situational Awareness (MSA) requires the ability to efficiently evaluate the probability of interaction of objects within the environment, without creating false alarms or ignoring materializing hazards. To do this, an MSA system needs to assign context to observed object activity and integrate as much information about object identity, kinematics, behavior, and current state as possible. This paper describes how known object characteristics, attributes, and activities (drilling, dumping, driving, etc.) can refine interaction probabilities and help identify rogue actors that introduce anomalous risks to the health and safety of miners. Path projections need to incorporate velocity and direction as a function of time while accounting for terrain, safety response, environmental factors, current assigned activity, etc. This paper also describes the methodology for properly prioritizing responses to place the highest value on human safety.

Feb 1, 2024

By Karl Ingmarsson

Larger mines spend millions of dollars annually on rock drilling tools, but often purchase based on historic consumption. The results vary from excess inventory to acute tools shortages. These lead to emergency sourcing, sometimes mixing products that don’t perform optimally. Boart Longyear analyzed the usage pattern of 96 thousand drill bits at thirteen different underground mining contracts, showing very high variability. The monthly standard deviation on a product level was 42%, with the highest for development and low volume bits. A new rule of thumb is suggested to carry only one month of safety stock for high volume bits, but increase to three months for low volume bits. This balance will reduce the risk of outages with less inventory. The accuracy can be improved by considering the specific conditions at each mine and reclassifying individual bits for a different safety stock level. Root cause analysis and collaborative forecasting between mines and suppliers can lead to further optimization of availability and inventory levels.

Feb 1, 2024

By J. I. Schoenherr, G. Schubert, T. A. Baloun

The currently known and used plastics and rubber recycling or sorting processes cannot be applied efficiently and economically due to large amounts and different numbers of plastics types as well as of fine bulky materials (<4mm). These wastes are mostly given to land-fill sites. Thermal adhesion seems to be a great means to efficiently separate plastics mixes. Tests carried out at a special lab-scale testing unit (TaA1) confirm the effectiveness and feasibility of the separating mechanism. The thermal properties of the individual types of plastics differ from each other to a sufficient degree so that special products or product mixes of high material purity can be obtained according to the respective requirements. For this reason, plastics mixes such as PE and PP can be sorted with very good results. The separation efficiency is influenced only by different contact surfaces. The contact period can be adjusted to a short period of time so that sorting large amounts of fine dispersed plastics seems feasible. Sorting processes in feed streams were shown to be technologically effective when applying appropriate technologies. For the time being, the technological application of a thermal adhesion drum separator (TaTr1) is suitable. First tests on such a pilot-scale unit provided good separation results.

Jan 1, 2004